Search Results

Search found 9122 results on 365 pages for 'sound card'.

Page 123/365 | < Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >

• Is there a grey-area with Copyright infringement?

  - by Z.O

  Currently a student, I'm trying to put together a game for iOS. From everywhere I've read, it seems any game's sound and art are apart of their IP and covered under their Copyright. That being said, say I wanted to use the coin sound effect from the original Mario (less than 1s long and used sparsely)... would anyone really care? Having no experience with this, I'm just wondering if cases like this are treated like "Ya you're driving slightly over the speed limit, but nobody cares" or as "you stole that car". Thanks for any insight anyone may be able to provide.

  Read the article

• Best Ati Radeon x1200 drivers for 12.10

  - by Jaclyn

  [Long story short is at the bottom if you don't care about my ranting] Ok, well, I have the unfortunate distinction of having an Acer Extensa 4420 (Yes, the model with the faulty motherboard, and no, I do not know how it is still working either). Long story short I need the best drivers for my Ati Radeon x1200 integrated graphics card. The Ati Propriatary drivers for 12.10 no longer supports my video card. Currently when I try to play Minecraft, or any game really, the framerate is quite terrible despite the fact that my handy dandy system load monitor says that I have plenty of memory and CPU power (Mind you, this is when I'm not playing minecraft; that kind of uses up all of my resources unless it's on the worst graphical settings, and even then I have terrible framerate, but plenty of resources left over). I tried the fglrx through a workaround guide, and it completely killed my display and I had to uninstall it. I'm considering just trying to install fglrx through synaptic, but I am hesitant to do so since I don't want a repeat of the BSBDD!!! (Black Screen of Bad Drivers 'o DOOOM!!!), so I will wait until after I get some input from you fine ladies and gentlemen on to what your advice it. ok, so I'm running xubuntu 12.10 64 bit. I upgraded from 10.10 to 11.04. Then about a month ago I went from natty to quantal via the update option in the package updater, and then I decided that I was sick of gnome so I installed xfce. I did not install new drivers from natty to when I wound up at 12.10, so that shouldn't have changed, and they were indeed quite terrible back then, but now I'm using xubuntu as my main os, so I actually need good drivers. uuuugh. Anyway, long story short: I need to know what are the best drivers available for my card, and how to install them, because I am a linux novice, and I have tried everything that I can think of, including search google. Small edit: I forgot to note that since I upgraded to 12.10, my VGA out does not work (I haven't had a chance to try the s-video yet), and possibly related, the USB port on that side of my laptop does not work anymore either.

  Read the article

• Some Flash moving portions displayed incorrectly in Firefox 5

  - by hansioux

  I am using 11.04 Natty and Firefox 5. Video card is ATI Radeon HD 4670 and I am using the newest proprietary driver downloaded from ATI website. Some Flash apps, such as embedded youtube vids and a couple of other apps, are displayed incorrectly (i think with real embed instead of the new iframe embed). What happens is as a portion of the flash moves around, parts of it keeps blanking out. For the embedded youtube vid, it greys out. Some other apps turns transparent, showing the webpage's background. The same flash apps runs perfectly fine for Google Chromium on the same computer. I have another computer with 10.10 Maverick, Firefox 5 and nVidia card and driver, and it they also run fine. So, anyone has an idea of what is causing the problem?

  Read the article

• cpu usage and near to crash when i plug in the power cable

  - by mohamad

  i have had this problem since i installed ubuntu 12.4 on my laptop (on all of distro i have this problem execpt of backtrack) my problem is when i start my linux while it connect to power source there is no problem everything works fine . but when i disconnect and wants to work with battery it crash i mean everything work tooooo slowly and my cpu usage goes to 100 ... it happen too when i start my linux with battery and want to connect the power source to it .... it happens again . i updated my distro and now on i have 12.10 on my laptop but it has this problem . my lap top is hp probook 4520s my graphic card is ati radeon 530 v and i installed catalyst control center on my lap top and it works fine but the only problem is that what i said ...is it relate to my graphic card ???

  Read the article

• Upgrade to Xubuntu 11.04 Breaks Wireless

  - by fleamour

  When I tried to connect at my mother's house and then my brother's house; the little connection icon would circle forever before eventually prompting for password. I have triple checked all network keys & then some. Even with my home network I now have to revert to 10.04 LTS Lucid Lynx (dual boot) or wired Ethernet. Not even sure where to start trouble shooting TBH? My card is a Edimax EW-7108PCg PCMCIA card which I bought for it's out the box Linux compatibility. Hardware is an IBM Thinkpad T21.

  Read the article

• pulseaudio on ubuntu server

  - by Dan

  I am running ubuntu server, and trying to get pulseaudio working. I followed the instructions at How do I run PulseAudio in a headless server installation? At the moment, pacmd list-cards is reporting 0 cards, and I suspect this has something to do with the fact aplay is only playing sound when I run it as sudo. As far as I can tell, this means the the kernel module for my sound card is in fact loaded. I have already tried adding my user to the "audio" group, but this does not help. My questions are 1) How do I get aplay to work without running it as sudo 2) Is there anything special I need to do to make pulseaudio work at this point.

  Read the article

• Internal Mic Ubuntu 12.04 on Compaq Presario CQ50

  - by Genius FDE

  I have problem with the internal microphone not working on Ubuntu 12.04. It looks like a common problem on most of the laptops running ubuntu 12.04. I tried a lot of possible solutions available online but nothing seems to work! sudo aplay -l gives: **** List of PLAYBACK Hardware Devices **** card 0: NVidia [HDA NVidia], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 By the way, the Laptop has no HDMI port! I've seen the same problem with Sony laptop but the mic was working with too much static noise. Thank you.

  Read the article

• pulseaudio and alsa on ubuntu 12.04 server

  - by Dan

  I am running ubuntu 12.04server, and trying to get pulseaudio working. I followed the instructions at How do I run PulseAudio in a headless server installation? At the moment, pacmd list-cards is reporting 0 cards, aplay will only playing sound when I run it as sudo, and running alsamixer as sudo also works, but running it as my user produces "cannot open mixer: No such file or directory" As far as I can tell, this means the the kernel module for my sound card is in fact loaded. I have already tried adding my user to the "audio" group, but this does not help. The permissions on the devices in /dev/snd are all crw-rw---T 1 root audio 116 I noticed on an ubuntu 12.04 desktop, that the file permissions are slightly different. On the desktop, they are crw-rw---T+ 1 root audio 116 My questions are 1) How do I get aplay to work without running it as sudo on the server 2) Is there anything special I need to do to make pulseaudio work at this point.

  Read the article

• What method replaces GL_SELECT for box selection?

  - by Jake

  Last 2 weeks I started working on a box selection that selects shapes using GL_SELECT and I just got it working finally. When looking up resources online, there is a significant number of posts that say GL_SELECT is deprecated in OpenGL 3.0, but there is no mention of what had replace that function. I learnt OpenGL 1.2 in back in college 2 years back but checking wikipedia now, I realise we already have OpenGL 4.0 but I am unaware of what I need to do to keep myself up to date. So, in the meantime, what would be the latest preferred method for box selection? EDIT: I found http://www.khronos.org/files/opengl-quick-reference-card.pdf on page 5 this card still lists glRenderMode(GL_SELECT) as part of the OpenGL 3.2 reference.

  Read the article

• Use a template to get alternate behaviour?

  - by Serge

  Is this a bad practice? const int sId(int const id); // true/false it doesn't matter template<bool i> const int sId(int const id) { return this->id = id; } const int MCard::sId(int const id){ MCard card = *this; this->id = id; this->onChange.fire(EventArgs<MCard&, MCard&>(*this, card)); return this->id; } myCard.sId(9); myCard.sId<true>(8); As you can see, my goal is to be able to have an alternative behaviour for sId. I know I could use a second parameter to the function and use a if, but this feels more fun (imo) and might prevent branch prediction (I'm no expert in that field). So, is it a valid practice, and/or is there a better approach?

  Read the article

• Low graphics mode on Ubuntu 12.04 with Intel Graphics

  - by NightShadeQueen

  When I boot, my computer just tells me it can't detect graphic card (or something else) settings and it has to use the low graphics mode. Then it gives me four choices, but doesn't let me choose any of them. I can get my computer to boot by going to some sort of terminal mode and then typing sudo gdm. The other graphics manager I have is lightdm. I originally had the nVidia propriety driver, and I've tried bumblebee. Mobile Intel Graphics Media Accelerator 4500M is my graphics card. Is there any way to fix this so I can use lightdm again?

  Read the article

• Triple monitor setup with an ATI Radeon 4200?

  - by Ben Clapp

  I have a relatively new Powerspec computer (i5 quad core processor, about a year or two old) and just grabbed a new relatively inexpensive ($40?) graphics card. It has 1 DVI, one VGA, and one HDMI output. I have two (different type) monitors plugged into the DVI and VGA slots, and they work great. However, I cannot seem to be able to get a third monitor in the HDMI slot to work. I can see the monitor (and monitor info) show up in display settings. However, if I try to switch the monitor to 'on' and click apply, nothing happens. Anyone have the slightest idea what the problem might be? (It's a Radeon graphics card FYI; if I remember right I think it was the Radeon 4200?)

  Read the article

• Bumblebee : Module bbswitch could not be loaded

  - by StepTNT

  I've upgraded to 12.04 and I had to switch from Ironhide to the latest version of Bumblebee. Now, when I try to run bumblebeed, I get this error: FATAL: Module bbswitch not found. [ERROR]Module bbswitch could not be loaded (timeout?) [WARN]No switching method available. The dedicated card will always be on. I don't really need to use the secondary VGA on Kubuntu, so I would like to find a way to definitely shut the discrete GPU down and avoid wasting battery. I can't disable it from the BIOS because I use it on Windows. My card is an nvidia 540M.

  Read the article

• Does an onboard video affect the X windows configuration?

  - by Timothy

  Does the onboard video on the motherboard affect the X windows configuration? My system has onboard and pcie video. The onboard video is a NVIDIA GeForce 7025 GPU, On Board Graphic Max. Memory Share Up to 512MB(Under OS By Turbo Cache). I have a pcie dual head video card installed with two monitors. The video card is a GeForce 8400 GS, with 512mb memory. When installing Ubuntu 12.04, only one monitor worked. When pulling up system settings- Displays it shows a laptop. This is a desktop pc. I did get both monitors to work using nvidia using twinview -- A complicated process! When checking nvidia now it shows the monitors disabled. The Nvidia X server setting does show the GPU and all the information. I was thinking it's seeing the onboard video on the motherboard. Why else would it show laptop?

  Read the article

• Macbook Pro 8,2 Graphics switching - Ubuntu 12.04

  - by fgs

  I've been reading docs and various pages for a few hours now and can't seem to put all of the pieces together on this. Basically I am trying to get 12.04 installed on my MBP 8,2 with graphics card switching working in some way or another. My basic understanding is that I need to do an EFI boot install of ubuntu so that graphics card switching will work (due to the hardware design). From there I may be able to use one of the kernel modules for graphics switching: https://help.ubuntu.com/community/HybridGraphics That article isn't clear on whether I need to do an EFI install. I have also seen comments in posts here that say and EFI install works by default as long as you have refit installed. Overall, I'm quite lost as to the simplest way to proceed to get an install up and running with graphics switching. I don't mind using open source GFX drivers as long as the basics work. Any help towards a solution is greatly appreciated.

  Read the article

• HighPoint RocketRAID 62x Controller

  - by TeXnewbie

  I have the subject card recently installed in Ubuntu 12.04.1 LTS (GNU/Linux 3.2.0-31-generic x86_64). See partial lspci -vv listing below (complete listing played havoc with pre tags): 03:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0622 (rev 01) Subsystem: HighPoint Technologies, Inc. Device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9c00 [size=8] Region 1: I/O ports at 9800 [size=4] Region 2: I/O ports at 9400 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8c00 [size=16] Region 5: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at fdbe0000 [disabled] [size=64K] Capabilities: I followed instructions I found at https://help.ubuntu.com/community/RocketRaid to compile the drivers for it, and although performing the process described there seemed to work fine with no noticeable errors, when I rebooted after performing that procedure I could not boot. During dkms steps, I noticed messages indicating that (If next boot fails, revert to initrd.img-3.2.0-31-generic.old-dkms image) update-initramfs................ so I booted using a Ubuntu 12.10 LiveDVD and reverted to the old-dkms initrd.img as suggested above, but this failed to repair the boot problem. Ultimately, I used https://help.ubuntu.com/community/Boot-Repair in Ubuntu-Secure-Remix to fix the boot problem and was able to boot normally again, but now with the newly generated initrd.img in place again (which now boots normally), when I modprobe the rr62x kernel module, I immediately get a hard crash with messages to console about a kernel paging request that seems to have caused the problem. I've tried on multiple occasions now to use the newly built kernel module so as to allow me to use an eSATA port multiplier plugged into the card, but to no avail. Any suggestions on fixes or workarounds (I've read that some of the HighPoint cards (2720SGL) seem to work as a host bus adapter and thus may not need a custom driver, but that seems not to be the case for mine) would be most appreciated. My goal is to use the card as described here and with software RAID mdadm utilities. If necessary, I can hand-copy the console messages after the hard crash into a follow-up message, but I obviously can't do a cut/paste. I'll gladly provide any other details that are needed, but not sure what those would be at this point, so I'll refrain from adding other details for now. Thanks in advance for any help.

  Read the article

• HTG Explains: How Do Noise Reducing Headphones Work?

  - by YatriTrivedi

  Passive noise reduction, active noise cancellation, sound isolation… The world of headphones has become quite advanced in giving you your own private sound bubble. Here’s how these different technologies work. Latest Features How-To Geek ETC Should You Delete Windows 7 Service Pack Backup Files to Save Space? What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions How to Enable User-Specific Wireless Networks in Windows 7 How to Use Google Chrome as Your Default PDF Reader (the Easy Way) WizMouse Enables Mouse Over Scrolling on Any Window Enhance GIMP’s Image Editing Power with Gimp Paint Studio Reclaim Vertical UI Space by Moving Your Tabs to the Side in Firefox Wind and Water: Puzzle Battles – An Awesome Game for Linux and Windows How Star Wars Changed the World [Infographic] Tabs Visual Manager Adds Thumbnailed Tab Switching to Chrome

  Read the article

• How to setup ATI Mobility Radeon HD 4650?

  - by Thi An

  I'm currently using Ubuntu 12.04 64bit. After installing ATI/AMD proprietary FGLRX graphics drivers via Additional Drivers, I checked the status of my VGA card using lspci -v. Here's the output: 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI M96 [Mobility Radeon HD 4650] (prog-if 00 [VGA controller]) Subsystem: Dell Device 0456 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at d0000000 (32-bit, prefetchable) [size=256M] I/O ports at 2000 [size=256] Memory at cfef0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at cfe00000 [disabled] [size=128K] Capabilities: Kernel driver in use: fglrx_pci Kernel modules: fglrx, radeon As mentioned in the title, my VGA card is 1GB and yet my computer only recognizes 256MB. My question is: "How to make my computer fully recognize the capacity of my ATI Mobility Radeon HD 4650 (1GB)?"

  Read the article

• NVidia with Optimus conflicting in Ubuntu 12.04

  - by Humannoise

  i have recently installed Ubuntu 12.04 in a Intel Ivy Bridge with integrated graphics and NVidia GPU with Optimus tech, however i cant manage it to work properly. I have already passed by the solution of bumblebee project, however iam got the following message when try to run anything with nvidia card( e.g. with optirun firefox): [ERROR]The Bumblebee daemon has not been started yet or the socket path /var/run/bumblebee.socket was incorrect. [ERROR]Could not connect to bumblebee daemon - is it running? Since the nvidia card is not working properly, some softwares like Scilab, that make use of X11 system for graphic handling and plotting, wont work too. my bios has no option concerning graphics card and the log of daemon returned: Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ bumblebeed[980]: Module 'nvidia' is not found. Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ kernel: [ 17.943272] init: bumblebeed main process (980) terminated with status 1 Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ kernel: [ 17.943288] init: bumblebeed main process ended, respawning Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ bumblebeed[1026]: Module 'nvidia' is not found. The lspci -nn | grep '\[030[02]\]:' returned: 00:02.0 VGA compatible controller [0300]: Intel Corporation Ivy Bridge Graphics Controller [8086:0166] (rev 09) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:0de9] (rev a1) Ok, for the command dpkg -l | grep '^ii' | grep nvidia i got : ii bumblebee-nvidia 3.0-2~preciseppa1 nVidia Optimus support using the proprietary NVIDIA driver ii nvidia-current 302.17-0ubuntu1~precise~xup1 NVIDIA binary Xorg driver, kernel module and VDPAU library ii nvidia-current-updates 295.49-0ubuntu0.1 NVIDIA binary Xorg driver, kernel module and VDPAU library ii nvidia-settings 302.17-0ubuntu1~precise~xup3 Tool of configuring the NVIDIA graphics driver ii nvidia-settings-updates 295.33-0ubuntu1 Tool of configuring the NVIDIA graphics driver After full reinstallation, including the remove of any previous nvidia drive, lsmod | grep -E 'nvidia|nouveau' returned: nvidia 10888310 46 dmesg | grep -C3 -E 'nouveau|NVRM' returned things like: [ 1875.607283] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1875.607289] nvidia 0000:01:00.0: setting latency timer to 64 [ 1875.607293] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none [ 1875.607363] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 302.17 Tue Jun 12 16:03:22 PDT 2012 [ 1884.830035] nvidia 0000:01:00.0: PCI INT A disabled [ 1884.832058] bbswitch: disabling discrete graphics [ 1884.832960] bbswitch: Result of Optimus _DSM call: 09000019 Some programs, like Scilab, are now working fine under optirun(e.g. >optirun scilab) call. Thank you.

  Read the article

• How do I record audio through M-Audio Keystudio?

  - by interstar

  Hi, I'm trying to get my M-Audio Keystudio (which has an audio input as well as the keyboard) to record audio to Audacity. I'm in Ubuntu 10.10. When I look at the Sound Preferences I can select "M-Audio RunTime DFU Analog Stereo" as my input device. However, when I try to record in Audacity, Audacity remains frozen. The program seems to be running and recording, but the recording cursor won't advance. If I reset the audio input to the internal sound card, recording works normally. Any ideas what to look for?

  Read the article

• /etc/X11/xorg.conf doesn't exist?

  - by BBetances

  I'm trying to get my video card properly setup to handle 3D acceleration. After searching a bit, I've come across a few howtos that tell me I need to edit my xorg.conf file. That file doesn't exist. X.org is installed by default, I'm sure, and I figured this video card would be widely supported. 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) Any ideas on how I can get this to work properly and play Starcraft II? Or any game for that matter? No resolution problems or anything, just no 3D rendering.

  Read the article

• Getting WLAN on my Laptop to work (Medion MD98300)

  - by Anand Böhmer

  Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

  Read the article

• Installing old Loki games on 12.04 64-bit results in no audio

  - by FlabbergastedPickle

  All, Here's an interesting problem. I followed instructions provided online for installing Loki Games' Heroes of Might and Magic 3 (see http://www.swanson.ukfsn.org/loki/ and http://wtanaka.com/node/7641) and got it installed and patched to the latest version. However, every time I start it regardless whether the pulseaudio is running, I get the following error: LD_LIBRARY_PATH=/usr/local/lib/Loki_Compat/ /usr/local/lib/Loki_Compat/ld-linux.so.2 /usr/local/games/Heroes3/heroes3.dynamic ALSA lib conf.c:3314:(snd_config_hooks_call) Cannot open shared library libasound_module_conf_pulse.so ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM default Couldn't open audio: My first soundcard is HDMI output and my second one is the actual soundcard (HP DM1 running 12.04 64-bit with latest updates). I did set up /etc/asound.conf as follows: asound.conf pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } So, the default soundcard should work ok. Between Shadowgrounds that also stopped working and this it appears a there may be some unfinished business/regressions in 32-bit support on 64-bit systems in 12.04. Any thoughts?

  Read the article

• Why is my fan constatnly blowing in Ubuntu?

  - by Derfder

  I have installed Ubuntu 13.04 (64-bits) alongside Windows 7 on different partition on my second desktop. It's working nice. I have updated everything. However, I have problems with my fan. It's blowing non-stop and very fast(loud). I haven't these problems in Windows 7 where it works nicely. How to update drivers for my fan or something else? My desktop is: HP Pro 3410 Microtower PC. Graphic card: AMD Radeon HD 6570 Board: 2A9C 1.1 Bus Clock: 133 megahertz BIOS: American Megatrends Inc. 6.14 11/05/2010 Processor: 3,20 gigahertz Intel Core i3 550 DRIVERS I HAVE TRIED FOR MY GRAPHIC CARD: I have tried these drivers so far: xserver-xorg-video-ati, version: 1:7.1.0-0ubuntu2 fglrx Version: 2:9.010-0ubuntu3 fglrx-updates Version 2:9.012-0ubuntu1 But the fan is still blowing like a maniac. I have tried to install Linux Mint 15 previously and I have had the same problems with the fan. Any idea how to fix it?

  Read the article

• Why doesn't LightDM always doesn't start under XEN

  - by DaedalusFall

  When I use XEN on Ubuntu (12.10), I have a problem that lightdm sometimes doesn't start when I boot up, I have to log in on the TTY and use sudo service lightdm restart, sometimes several times. Some of the time I get a mouse cursor and a blinking underscore in the top left of the (otherwise black) screen, but after restarting lightdm a few times it eventually comes up properly. I've tried this with XEN from the repos (version 4.1), XEN 4.2 built from source, an NVIDIA card and a radeon card (not using fglrx, which I can't seem to make work under XEN), the results are more or less the same. I can't see anything obvious in my Xorg.log, but I'm not really sure what to look for. Anyone had similar problems or luck getting xen working? Thanks in advance.

  Read the article

< Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >