Search Results

Search found 9105 results on 365 pages for 'disk quota'.

Page 125/365 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• CDROM does not appear on desktop, MACOS 10.5.7

  - by Cheeso

  When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

  Read the article

• Xen Windows Guest spawn doesn't spawn a vnc display

  - by Henrik P. Hessel

  I'm using this HVM File to create a new guest kernel = "/usr/lib/xen-3.2-1/boot/hvmloader" builder='hvm' memory = 4096 # Should be at least 2KB per MB of domain memory, plus a few MB per vcpu. shadow_memory = 64 name = "hessel-windows2008" vif = [ 'ip=188.40.xx.xx,mac=00:16:3E:C1:8F:CE' ] acpi = 1 apic = 1 disk = [ 'file:/home/xen/disks/hessel/win2008/win2008.img,hda,w', 'file:/home/xen/isopool/win2008_32.iso,hdc:cdrom,r' ] device_model = '/usr/lib/xen/bin/qemu-dm' #----------------------------------------------------------------------------- # boot on floppy (a), hard disk (c) or CD-ROM (d) # default: hard disk, cd-rom, floppy boot="dc" sdl=0 vnc=1 vncdisplay=1 vnclisten="0.0.0.0" vncconsole=1 vncpasswd='howtoforge' stdvga=0 serial='pty' usbdevice='tablet' The guest is created without an error. But no vnc display is created. Any ideas, how to fix that? prometheus:~# netstat -ant Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:615 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:6010 0.0.0.0:* LISTEN tcp 0 232 188.40.xx.xx:8080 195.36.75.26:54032 ESTABLISHED tcp 0 0 188.40.xx.xx:8080 195.36.75.26:53085 ESTABLISHED tcp6 0 0 :::8080 :::* LISTEN tcp6 0 0 :::53 :::* LISTEN tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 ::1:6010 :::* LISTEN

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

• Performance monitoring on Linux/Unix

  - by ervingsb

  I run a few Windows servers and (Debian and Ubuntu) Linux and AIX servers. I would like to continously monitor performance on these systems in order to easily identify bottlenecks as well as to have an overview of the general activity on the servers. On Windows, I use Windows Performance Monitor (perfmon) for this. I set up these counters: For bottlenecks: Processor utilization : System\Processor Queue Length Memory utilization : Memory\Pages Input/Sec Disk Utilization : PhysicalDisk\Current Disk Queue Length\driveletter Network problems: Network Interface\Output Queue Length\nic name For general activity: Processor utilization : Processor\% Processor Time_Total Memory utilization : Process\Working Set_Total (or per specific process) Memory utilization : Memory\Available MBytes Disk Utilization : PhysicalDisk\Bytes/sec_Total (or per process) Network Utilization : Network Interface\Bytes Total/Sec\nic name (More information on the choice of these counters on: http://itcookbook.net/blog/windows-perfmon-top-ten-counters ) This works really well. It allows me to look in one place and identify most common bottlenecks. So my question is, how can I do something equivalent (or just very similar) on Linux servers? I have looked a bit on nmon (http://www.ibm.com/developerworks/aix/library/au-analyze_aix/) which is a free performance monitoring tool developed for AIX but also availble for Linux. However, I am not sure if nmon allows me to set up the above counters. Maybe it is because Linux and AIX does not allow monitoring these exact same measures. Is so, which ones should I choose and why? If nmon is not the tool to use for this, then what do you recommend?

  Read the article

• Converting An Older VMWare Image to ESXi

  - by Bart Silverstrim

  I have just installed VMWare ESXi and imported one physical machine without issue and one virtual machine, from an older version of VMWare Server on a Linux system, to it without issue. But I have another machine (Windows XP), virtual running on the VMWare Server, that I can't get the Converter to work with. Converter runs, says everything is fine, but when I go to the ESXi VSphere manager and hit the button to power up that vm, the console stays black with a blinking cursor and the processor for that VM spikes 100% and stays there. An event log item in VSphere warns something about activation issues with Windows. Has anyone else run into this issue before? Is it something with the disk controller? I copied the folder with the VM directly to the storage drive on ESXi hoping to create a new machine and point the data store to that folder or at least that drive image; nope, something about not using an IDE controller (must be something with the older format). In short, converter is doing something that particular machine doesn't like, and I can't find a way to simply open that hard disk image or convert it unless someone else has seen this. I try attaching a bootable CD image for disk repair to see if it can check the hard drive but I can't seem to get the console to boot from it...either too slow on the button or it just isn't able to easily boot from a virtual drive image (.iso). Any suggestions or help?

  Read the article

• Representing server state with a metric

  - by Sal

  I'm using Microsoft's Performance Monitor to dump logs of RAM, CPU, network, and disk usage from multiple servers. I'd like to get a single metric that captures the state of a given variable to a good extent. For instance, disk usage is pretty stable, so if I take a single reading that says I have 50% remaining disk space, that reading will give me an accurate measure for the day. (The servers aren't doing heavy IO writing.) However, the tricky part here is monitoring CPU and network usage. The logs currently dump the % CPU usage every ten seconds. If I take a straight average of the numbers, it may not represent reality, as % CPU will be much lower during the night than day. (We host websites that sell appliance items.) I'd like to get an average over a span during peak hours (about 5 hours in the day) and present a daily peak hour metric. Of course, there are most likely some readings that will come in as overly spiked (if multiple users pinged the server at once) or no use (a momentary idle state). Is there a standard distribution/test industries use in these situation?

  Read the article

• what is the fastest way to copy all data to a new larger hard drive?

  - by SUPER user

  I was certain this would have been covered before, but I cannot find an answer amongst all the almost-duplicates that come up; sorry if I've missed something obvious. I have a full 320gb disk inside my machine, a new 1tb disk to replace it, and a USB 2.0 chassis. It is only data on a single partition, no OS/apps involved, and the old drive will be kept somewhere as backup (no secure wiping etc). The simple option would be to put new disk in USB chassis, copy files, then swap them over. But for USB pen drives, reading is around 4x faster than writing. If the same is true for a USB SATA chassis (is it?) then it would be significantly faster to swap the drives first and read from the old drive over USB, right? Then the other consideration is that copying lots of files is usually slower than a single file of equivalent size. Is Windows 7 smart enough to do everything in a single lump like that, or is there specialised software that should be used instead? (Even if SATA-SATA copying is faster than involving USB, knowing what to do when it isn't an option is useful information.) Summary: Does a USB SATA chassis suffer from a read/write inequality? (like a USB pen drive does, but unlike a direct SATA connection) Can Windows 7 do sequential access? (I can't find confirmation if Robocopy does this.) Or is it necessary to use a bootable CD/USB with something like Clonezilla to achieve sequential copy speeds?

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated.

  Read the article

• Adobe e-book reader ("Digital Editions") not downloading on Mac OS X

  - by doug

  i recently bought a couple of books from ebooks.com, which i thought would be ordinary pdf files. After paying for them, and downloading them, you learn that while they are pdf files, they come with a lot of DRM baggage. The most conspicuous is that you can only view these files using an Adobe ebook reader called Adobe Digital Editions. (Note: this is not the ordinary Adobe Acrobat Reader, or anything close--it's a dedicated app for reading DRM-laden files. Fine--i'll know better next time. Still, i paid for these books and there's only one way i can actually read them, which happens to be an App that i seem to be unable to download. Here's the error message i get: "Couldn't write the application to the hard disk. Please verify the hard disk is available and try again" I've tried on several different browsers. My rig is a MBP, OS X 10.6.2. I've also checked the Adobe boards and this doesn't appear to be a known issue, nor could i find anything on their discussion forums. And just to be sure, i've checked my hard disk--no problems, plenty of space, and i have no problem, nor have i ever downloading other apps.

  Read the article

• Permission denied problem in Freenas + Transmission

  - by Torbjörn Karlsson

  Running Freenas 0.7.2 (5543) and Transmission 2.11 The problem it that i can not save a torrent where ever i want.. For example... I can save in: /nmt/1-500gb/Tv/dexter but i can not save in /nmt/4-1000gb/tv/Lost When i try to save in the lost folder I get a permission denied error in the Web interface. But when I try to save the same torrent file in the dexter folder everything works fine... This is probably an easy thing to fix, but I'm new to Freenas. The user name for Transmission is TorrentUser if that helps. Now I find out that I can not browse the disk in Quixplorer.. I can browse nmt/4-1000gb/ but not /nmt/1-500gb When I try to browse the nmt/4-1000gb/ I get Unable to read directory $ mount /dev/md0 on / (ufs, local) devfs on /dev (devfs, local) procfs on /proc (procfs, local) /dev/fuse1 on /mnt/5 - 500gb (fusefs, local, synchronous) /dev/fuse2 on /mnt/2 - 1000gb (fusefs, local, synchronous) /dev/fuse3 on /mnt/3 - 1000gb (fusefs, local, synchronous) /dev/fuse4 on /mnt/4 - 1000gb (fusefs, local, synchronous) /dev/fuse5 on /mnt/320GB - USB (fusefs, local, synchronous) /dev/md1 on /var (ufs, local) /dev/da0a on /cf (ufs, local, read-only) /dev/fuse0 on /mnt/1 - 500gb (fusefs, local, synchronous) Dont work : 1 - 500gb 2 - 1000gb 3 - 1000gb Works: 320GB - USB 4 - 1000gb 5 - 500gb And this 3 disk is the same disks that I can save my torrents to. Ps. Every disk works perfect when i use ftp...

  Read the article

• Parallels Plesk returning strange numbers

  - by Jack W-H

  Hi everyone, As a relatively new Server Admin I've become a bit confused by some statistics Parallels Plesk Panel 10.0.1 is returning to me. I have a domain ('subscription') set up, mysite.com. Mysite.com only hosts files, mostly images Its file contents use up about 390MB of disk space Here's a screenshot: this is what Plesk is reporting mysite.com to use: And some more info: Now this is pretty confusing... I thought at first my site might have been hacked and had contents written to disk, but I checked and all is in order, nothing has been hacked into as far as I can tell. So I had a look in the site's CP for some more in-depth statistics, and this is what's returned... Now - sod's law - when I go to check my disk space statistics in more depth via the control panel, this morning it says "The data were not collected yet." - not too sure what that means, but, last night when I checked it was reporting something odd. It said Files were using up 390MB, but 1.80GB or so were being used up by 'Mail Accounts'. This is really strange, as there are no mail accounts set up for the domain. The only hint of 'mail' there is, is the catchall set up to forward *@mysite.com to a separate, ISP-hosted email account. Any ideas anybody? I can post more details if you need it. Sorry to be a bit vague but I'm not sure what else I can post. Thanks, Jack

  Read the article

• OS X borked; need to backup outside of Time Machine

  - by rlbgator

  Quick Background: iMac G5 (the white one; 4 years old?) Running Leopard 10.5.something. Time Machine started failing on me; and every time I touch the Finder, things beachball like crazy. Booting from install disk then using Disk Utility to "Repair Disk" also fails. I'm left with the conclusion that I have a corrupt file somewhere important, that's (i) keeping TM from working and (ii) messing with basic functionality. I am not (yet) savvy enough in OS X to know what logs to look in, or how to decipher them - but 'corrupt file' seems to be the likely case, based on my readings of apple.com forum threads. So I think I need to backup, outside of Time Machine, then install fresh OS X on a new drive (or maybe SpinRite the current drive?). I'm able to put a (non-Time Machine) external USB drive on, so I dragged all 3 Users' folders to that... am I done backing up? Am I going to have a massive Permissions problem, trying to put things back together after a re-install? Thanks for reading.

  Read the article

• Sparing level on HP EVA 4000

  - by Samuel

  One of the disks of our EVA4000 died today. This diskgroup (all volumes vraid5 with sparing level 1 and almost no space left for more volumes, 1TiB drives) is being rebuilt with "spare space" right now, and it will take at least 15 hours to do the leveling/rebuilding. We can't get a new disk until Friday. So, the question is, what would happen if another disk dies before the leveling completes? Would we lose data? And after that, how many aditional disks could die before losing data? 1 or 2? In "usual" RAID, we would be vulnerable to data loss while the rebuild takes place, but in this case the space reserved for sparing is two times the size of the bigger disk, so at the very least the effect should be the same of having two spares. Thanks in advance. Update: I have found some interesting threads about this question but still can't answer to this question, so I'm starting a bounty. http://blog.thestoragearchitect.com/2008/10/27/understanding-eva/ http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&url=http%3A%2F%2Fwww.experts-exchange.com%2FStorage%2FStorage_Technology%2FQ_25548177.html (Expert Exchange question from google).

  Read the article

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• Where is '/host' declared for mount in Wubi (Ubuntu 9.10)?

  - by Pedro

  Hi! I'm using Wubi (ubuntu 9.10), and I couldn't find where '/host' mountpoint is declared for mounting. There's no entry in fstab, but it's listed in /proc/mount and mounted at boot time. Any ideas? pedroel@ubuntu:~$ cat /proc/mounts rootfs / rootfs rw 0 0 none /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 none /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,relatime,mode=755 0 0 /dev/sda1 /host fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 0 0 /dev/loop0 / ext4 rw,relatime,errors=remount-ro,barrier=1,data=ordered 0 0 none /sys/kernel/security securityfs rw,relatime 0 0 none /sys/fs/fuse/connections fusectl rw,relatime 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 none /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 none /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0 none /var/run tmpfs rw,nosuid,relatime,mode=755 0 0 none /var/lock tmpfs rw,nosuid,nodev,noexec,relatime 0 0 none /lib/init/rw tmpfs rw,nosuid,relatime,mode=755 0 0 /dev/loop1 /home/pedroel/Downloads ext4 rw,relatime,errors=remount-ro,barrier=1,data=ordered 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 gvfs-fuse-daemon /home/pedroel/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0 /dev/mapper/isw_efhafcifi_RAID_Volume01 /media/RAID_D fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 pedroel@ubuntu:~$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # proc /proc proc defaults 0 0 /host/ubuntu/disks/root.disk / ext4 loop,errors=remount-ro 0 1 /host/ubuntu/disks/pedro.disk /home/pedroel/Downloads ext4 loop,errors=remount-ro 0 1 /host/ubuntu/disks/swap.disk none swap loop,sw 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 Thanks in advance, Pedro

  Read the article

• VMWare Setup with 2 Servers and a DAS (DELL MD3220)

  - by Kumala

  I am planning to use a VMWare based setup consisting of two VMWare servers (2 CPU, 256GB Memory) and a DAS (DELL MD3220 with 24x900GB disks). The virtual machines will be half running MS SQL databases (Application, Sharepoint, BI) and the other half of the VM will be file services, IIS. To enhance the capacity of the storage, we'll be adding a MD1220 enclosure with another 24x900GB to the MD3220. Both DAS will have 2 controllers. Our current measured IOPS is 1000 IOPS average, 7000 IOPS peak (those happen maybe twice per hour). We are in the planning phase now and are looking at the proper setup of the disks. The intention is to setup up both DAS one of the DAS with RAID 10 only and the other DAS with RAID 5. That will allow us to put the applications on the DAS that supports the application performance needs best. Question is how best to partition the two DASs to get best possible IOPS/MBps, each DAS will have to have 2 hot spares? For the RAID 5 Setup: Generally speaking, would it be better to have one single disk group across all 22 disks (24 - 2 hot spares) with both controllers assigned to the one disk group or is it better to have 2 disk groups each 11 disks, assigned to one of the two controllers? Same question for the RAID 10 setup: The plan is: 2 disks for logs (Raid 1), 2 Hotspare and 20 disks for RAID 10. Option 1: 5 * 4 disks (RAID 10), with two groups assigned to 1 controller and 3 groups to the other controller Option 2: One large RAID 10 across all the disks and have both controllers assigned to the same group? I would assume that there is no right or wrong, but it all depends very much on the specific application behaviour, so I am looking for some general ideas what the pros and cons are of the different options. IF there are other meaningful options, feel free to propose them.

  Read the article

• mount error 5 = Input/output error

  - by alharaka

  I am running out of ideas. After a long period of testing this morning, I cannot seem to get this to work, and I have no idea why. I want to mount a Windows SMB/CIFS share with a Debian 5.0.4 VM, and it is not cooperating. This the command I am using. debianvm:/home/me# whoami root debianvm:/home/me# smbclient --version Version 3.2.5 debianvm:/home/me# mount -t cifs //hostname.domain.tld/share /mnt/hostname.domain.tld/share --verbose -o user=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD/username mount.cifs kernel mount options: unc=//hostname.domain.tld\share,ip=10.212.15.53,domain=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD,ver=1,rw,user=username,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,pass=*********mount error 5 = Input/output error Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) debianvm:/home/me# The word on the nets has not been very specific, and unfortunately it is almost always environment-specific. I receive no authentication errors. I have tried mount -t smbfs and mount -t cifs, along with smbmount and such. I get the same error before. I doubt it is a problem with DNS resolution, because logging shows the correct IP address. dmesg | tail -f no longer shows authentication errors when I format the domain and username accordingly. I have played a little with iocharset=utf8, file_mode, and dir_mode as described here. That did not help either. I have also tried ntlm and ntlmv2 assuming it might be a minimum auth method problem, but not forcing sec=ntlmv2 it can still authenticate without errors anymore. smbclient -L hostname.domain.tld -W SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD -U username correctly lists all the shares and shows it as the following. Domain=[SUBADDOMAIN] OS=[Windows 5.0] Server=[Windows 2000 LAN Manager] Sharename Type Comment --------- ---- ------- IPC$ IPC Remote IPC ETC$ Disk Remote Administration C$ Disk Remote Administration Share Disk Connection to hostname.domain.tld failed (Error NT_STATUS_CONNECTION_REFUSED) NetBIOS over TCP disabled -- no workgroup available I find the last line intriguing/alarming. Does anyone have any pointers!? Maybe I misread the effin manual.

  Read the article

• How to install a desktop environment onto Ubuntu Server -- but without internet access or a CDROM?

  - by James

  I am playing around with a computer which has no CDROM drive or internet access and I have installed Ubuntu Server onto it. I have that all up and running nicely but now I'd like to install Xfce, GNOME or something similar so I can load up a desktop environment from the command line if I wish. Obviously with internet access or a CDROM, this would be a simple task of using apt-get and it finding & retrieving the packages for me, I assume, but I do not have either. I do however have a USB drive and I have used Unetbootin to make it into a bootable drive with the Ubuntu Server disk image files on there. I have mounted the USB drive to /media/usb0 and tried the command "sudo apt-cdrom add -d /media/usb0" to get apt to recognise the USb drive as an "Ubuntu CD" -- a source of package files but apt-get doesn't seem to be finding Xfce.. I try "sudo apt-get install xfce" and "sudo apt-get install xfce4" but neither find the package.. I would prefer to have Xfce but GNOME would be OK too.. My question is, am I doing something wrong? I figured that the Ubuntu Server disk (or rather, my Ubuntu Server USB drive) might not have any desktop environment packages on there so I tried the Xubuntu Desktop disk too (again, from my USB drive). I tried "sudo apt-get install xubuntu-desktop" but it couldn't find the package - even though it is listed under the /casper/ directory in some MANIFEST file. Anyone see where I'm going wrong? Maybe apt-get install is looking somewhere other than my USB drive? Maybe my commands are wrong? Maybe the disks don't even have the desktop environments on!? Thanks in advance guys, any input would be much appreciated. Cheers - James

  Read the article

• Dual-booting Ubuntu and Pardus with GRUB2...Pardus no show?

  - by Ibn Ali al-Turki

  I have Ubuntu 10.10 installed and used to dual-boot Fedora, but I replaced Fedora with Pardus. After the install, I went into ubuntu, and did a sudo update-grub. It detected my Pardus 2011 install there. When I rebooted, it did not show up in my grub2 menu however. I went back to Ubuntu and did it again...then checked the grub.cfg, and it is not there. I have read that Pardus uses a grub legacy. How can I get Pardus into my grub2 menu? Thanks! sudo fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd9b3496e Device Boot Start End Blocks Id System /dev/sda1 * 1 15197 122067968 83 Linux /dev/sda2 36394 60802 196059757 5 Extended /dev/sda3 15197 30394 122067968 83 Linux /dev/sda5 36394 59434 185075308 7 HPFS/NTFS /dev/sda6 59434 60802 10983424 82 Linux swap / Solaris Partition table entries are not in disk order and update-grub Found linux image: /boot/vmlinuz-2.6.35-25-generic Found initrd image: /boot/initrd.img-2.6.35-25-generic Found memtest86+ image: /boot/memtest86+.bin Found Pardus 2011 (2011) on /dev/sda3 Yet after this, I go to grub.cfg, and Pardus is not there.

  Read the article

• Can a folder on a NAS be made available as a physical drive in VMWare?

  - by asbjornu

  We are currently in the process of moving from a single web server to two load balanced web servers and are facing some challenges we don't quite know how to fix. One of these is that the current single server hosts applications that write stuff to disk. The applications running on the server expects that when something is written to disk it later will in fact exist, so it's important that this premise is fulfilled with the dual server architecture as well. The dual server setup is a couple of VMWare instances with Windows Server 2008 R2 as the guest operating system. Out of the box, these instances does not share any kind of file system, so just moving the applications over would make them break since one instance would write something to the file system that doesn't exist on the other. Thus we need to share a file system between the two virtual servers. Our host has proposed to create a network share on a SAN and map this share individually on each virtual machine. This doesn't work too well due to NTFS permissions, etc., because the share needs to be accessed by several independent web applications that won't even be in the same application pool. The only solution that kind of works is to hard code an "identity" for each web application into its web.config file, but this means password in clear text which doesn't sit well with me. Since the servers are virtual, I'm thinknig: Wouldn't it be possible to make a NAS area available as a physical disk in the gues operating system somehow? Since VMWare has full control of the virtual hardware, you'd think it would be able to "fake" a local hard drive in the virtual machine that in reality is a folder on a NAS, but so far I haven't found anything that states how and if this is possible. So I have to ask the wonderful Server Fault community: Can a folder on a NAS be made available as a physical drive (typical D:) in both of the virtual machines?

  Read the article

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• Windows Action Center notification icon says Backup in Progress when no backup is occurring

  - by allquixotic

  How can I get Windows Action Center's little flag in the notification area to stop saying "Backup In Progress" on Windows 8? It's driving me nuts. I disabled the Windows Backup service completely and turned off File Recovery. Nothing that I can tell is using any disk I/O whatsoever, by examining Task Manager's resource monitor. It's just a visual cue that seems totally wrong considering my disk is only using about 50 KB/s of sporadic writes for superfetch etc. This wouldn't be a problem for me, since I rely on the knowledge that the Backup service is disabled and there's no disk activity, but I am trying to support a more traditional user who relies on visual cues from the operating system and trusts them over low-level observations like "...but the Windows Backup service is disabled!" Therefore this user still thinks that the backup is going on, even after the service is disabled. Technically, I think this is a bug in Windows 8. It really should not be displaying "Backup in Progress" if ... you know ... a backup, is not, in progress. Which it isn't. Is there a workaround?

  Read the article

• Blank list of windows services

  - by Joe

  Recently when I open windows services (always as administrator) I get a blank list of services: When I try and click on one of the empty lines I get this "Script Error" message: This happens over and over again, after several times I restarted my computer. I can't pinpoint exactly when this started happening or if I made any specific changes to my computer at that time. Someone told my to try running scf /scannow as administrator, but when I try to do that the scan stops at 34% and I get the message: "Windows Resource Protection could not perform the requested operation." I am running Windows 7 Enterprise 64 bit, and I would really like to avoid reinstalling windows. Does anyone know how to fix this? Edit - Here is another attempt I made and some more information that might help: Following WhoIsRich's suggestion, I tried the command sfc /scannow /offbootdir=c:\ /offwindir=c:\windows. This gave the error message "The arguments passed to sfc are invalid. The offline windows directory specified points to the online system", and then I realized this command is meant to be run after booting from another system. Since I don't have my windows installation disk right now, I used my own system to create a recovery disk, and then restarted my computer and used the recovery disk to boot. I then ran the above command, and I got the following message: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.log". I then restarted my computer and let it boot up normally. The problem with windows services persists, and the CBS.log file is a long log file with many entries, and I don't know if there is useful information in it, and if there is, how to find it.

  Read the article

• Synchronising a remote folder with a local one.

  - by Workshop Alex

  I am using a network disk (that's connected to my router by USB) to store several data files. A simple .NET application that I've created is supposed to read and modify these data files. However, some security issues are preventing this application to access these files directly. (Actually, these have been built-in to my application on purpose since it's not going to support NAS disks.) Since this disk is shared with several computers, I just want to have a simple synchronisation method, which will copy the files to a local folder where3 my application can access them. And, once modified, it should send back the modified files to the NAS disk again. I have two options: 1) Build a second application to do my own synchronisation. 2) Find some build-in function inside Windows 7 Ultimate which can do this for me. Option 2 is preferred. Option 1 is something I can do easily, if need be. I don't need third-party tools. (Still, feel free to add some references to good tools, although I won't accept them as answers.) Basically, is this possible with Windows 7 and if so, how?

  Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >