Search Results

Search found 29432 results on 1178 pages for 'mite fine dailes'.

Page 126/1178 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

• Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

  - by Kairan

  Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

  Read the article

• Windows XP consuming drive letters

  - by billdehaan

  This one's a bit of a stumper. I'm running XP SP3, current with all fixes, etc. My problem is that I can assign a drive letter to a container file (explained below), it works just fine. But once I close the container, the drive letter is no longer available until the next boot. I've got some confidential data that I've placed in a container volume. I've used TrueCrypt (www.truecrypt.com) and FreeOTFE (www.freeotfe.org), with both installed and portable versions for both, with the same result. I open the container file, assign it to a drive letter (say R:), and run some portable apps that are within the volume. When I'm done, I close the container, and the drive letter is released. Fine so far. However, when I attempt to re-open it, the previous drive letter (in this case R:) is no longer available. It's not mapped to anything, it's just unavailable. Even attempting something like "subst R: C:\" returns "Invalid Parameter - R:". I can use the S: drive, no problem, but the next day I have to use T:, then U:, etc. Eventually, I have to reboot to reclaim all of of the drive letters. Unfortunately, everything I've read about drive letters relates to USB assignments, which doesn't apply here. I've tried the "show hidden" command (set devmgr_show_nonpresent_devices=1) with no success. And the Disk Management tool doesn't apply either, since it's not a physical drive. Does anyone know where Windows keeps the list of drive letters? And is there anything short of a reboot that can be used to reset it?

  Read the article

• Working with barcode fonts in Word

  - by Bob Rivers

  I need to create labels in Microsoft Word 2010 with numbers encoded as barcodes. The barcode's format (ean, code39, upc, etc) does not matter. I have downloaded a barcode conversion font that I found at this site. When I type the number that I want and then I format it with my new font, it produces a barcode. I then print it on an OKI laser printer (1200 dpi). The result seems to be fine, at least for common people. But, when I try to scan it, nothing happens. I tried both with a barcode scanner and a data collector, but neither of them read the barcode. My barcode scanner is working fine, because I can read commercial barcodes printed on products. Does anybody have any advice? How do I do this kind of stuff? I want to do it using Word because I will generate labels using Mail Merge. Therefore using external programs aren't option for me.

  Read the article

• Web SMTP Server(foo.com) will not send mail to exchange server which is also(foo.com)

  - by Atom

  I think I understand this problem fully, but I do not know how to approach it or where to go in terms of troubleshooting. I've got my one domain http://foo.com that runs a Zen Cart installation that needs to be able to send emails to users(order confirmation, password reset). This works fine to send to any other domain BUT foo.com. I'm running a locally hosted exchange server that is foo.com, and we can send and receive email just fine. If I run tail -f /usr/local/psa/var/log/maillog I recieve this error: Apr 1 10:08:51 foo qmail-local-handlers[25824]: Handlers Filter before-local for qmail started ... Apr 1 10:08:51 foo qmail-local-handlers[25824]: from= Apr 1 10:08:51 foo qmail-local-handlers[25824]: [email protected] Apr 1 10:08:51 foo qmail-local-handlers[25824]: cannot reinject message to '[email protected]' Apr 1 10:08:51 foo qmail: 1270141731.583139 delivery 32410: failure: This_address_no_longer_accepts_mail./ Apr 1 10:08:51 foo qmail: 1270141731.584098 status: local 0/10 remote 0/20 I understand that the foo.com SMTP service doesn't have any account but the one that is used to authenticate mail being sent, so of course, I understand why it's saying 'this address no longer accepts mail'. My question is, how can I get the foo.com(web) SMTP service to handle emails meant for my exchange server([email protected]) or how do I handle the mail that needs to be sent to our exchange server? Is this something to do with MX records? Thanks in advance A

  Read the article

• Dual Monitor Setup with Ati Radeon Hd 5700 results in unusabledesktop win7

  - by NorthPole

  I have an ATI Radeon HD 5700 card which i've been using under fully updated windows 7 with its latest drivers. My monitor is a 2004 NEC LCD1703M which despite being pretty old runs fine. A friend gave me an IIYAMA ProLite E1900WS monitor (2009 or 20010 ). Both monitors are vga only. I've been using a DLDVI to VGA adapter to connect my old monitor and tested the same adapter to the new monitor and it worked fine. So I bought an HDMI to vga adapter with the purpose of having a dual monitor setup. But when both screens are connected to the card the following problem occurs: The monitor connected to the hdmi port cycles between sleep and a black screen while the other shows the operating system for about two seconds before getting black for another two seconds. I can "use" the computer (move the mouse,click,type e.t.c.) while this happens but its not something pleasant. I tried reinstalling the driver, booting with both screens connected (in which case the powerup messages and the bios are mirrored in both screens until I get to the login screen where everything falls apart) Funny thing is, everything works if I disconnect the ATI graphics card and use the onboard intel one. So, any suggestions as to what might be the problem and how I can fix it?

  Read the article

• can't ssh within LAN, but can connect from outside

  - by Patrick B.

  A strange issue: I have a desktop running Ubuntu 10.04 behind a Netgear WNR1000 router performing NAT. I would like to be able to ssh into the desktop from my laptop (running Windows 7 and Cygwin). When at home, both the desktop and the laptop are connected by wireless (the desktop is in a different room from the router). sshd seems to be running fine, since ssh localhost from the desktop works without trouble. Also, ssh my.ip.address from my laptop when it is not behind the router works fine (I am forwarding port 22 on the router to my desktop). However, ssh same.ip.address from within the LAN fails with "Connection refused". ssh 192.168.local.ip.address fails with a different message, "Connection timed out". I can connect if I first ssh to a machine outside the LAN. So far I haven't found anything with Google because with the search terms that seem like they would be relevant, the vast majority of people have the opposite problem - i.e., they can't connect from outside the LAN but can connect within it. I can port forward through a remote server when I'm at home, but this seems like a totally absurd way to connect two computers on the same home LAN. I have already tried stopping and starting sshd on the desktop. Any thoughts?

  Read the article

• Perl EPIC Not recognising installed CPAN modules

  - by Recc

  Eclipse on a mac, was working fine adding new modules until I Installed Text::CSV_XS which Eclips doesn't recognise as added to @INC For instance use strict; use SOAP::Transport::HTTP; SOAP::Transport::HTTP::CGI->dispatch_to('C2FService')->handle; BEGIN { package C2FService; use vars qw(@ISA); @ISA = qw(Exporter SOAP::Server::Parameters); use SOAP::Lite; sub c2f { my $self = shift; my $envelope = pop; my $temp = $envelope->dataof("//c2f/temperature"); return SOAP::Data->name( 'convertedTemp' => ( ( ( 9 / 5 ) * ( $temp->value ) ) + 32 ) ); } } use SOAP::Transport::HTTP; is marked as error if I comment it out use SOAP::Lite; is in turn marked as an error, not found etc the usual if a module is not installed. Both are installed with CPAN and $ perl -c soap-test.pl post-code-check.pl syntax OK Perl is fine CPAN tests are all pass, the code works, only EPIC lags behind. $ pwd && ls /opt/local/lib/perl5/site_perl/5.12.4/SOAP Client.pod Lite Server.pod Constants.pm Lite.pm Test.pm Data.pod Packager.pm Trace.pod Deserializer.pod SOM.pod Transport Fault.pod Schema.pod Transport.pod Header.pod Serializer.pod Utils.pod And if I have use errors in the start of my files the rest of the source is not error checked..

  Read the article

• exim4 to relay emails

  - by Matthieu

  I have exim4 installed on a Linux box. The basics work fine and I can send email from that machine without any problem to whatever email address. I also have a printer/scanner which is capable to send scans as emails. It needs an SMTP gateway to be able to do that. So I give the IP address of that Linux box, changed the configuration a little bit but still cannot get it to work. After I run dpkg-reconfigure exim4-config, here is what I get in /etc/exim4/update-exim4.conf.conf : dc_eximconfig_configtype='internet' dc_other_hostnames='' dc_local_interfaces='127.0.0.1;192.168.2.2' dc_readhost='' dc_relay_domains='mycompanyemail.com' dc_minimaldns='false' dc_relay_nets='192.168.2.0/24' dc_smarthost='' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='' dc_mailname_in_oh='true' dc_localdelivery='mail_spool' My problem is that with this configuration, I can only send to emails @mycompanyemail.com... It says I can use wildcard, but when I do that, the '*' is replaced by whatever filename is in the directory where I run all that. How can I configure it to be able to send emails with any domain ? Or am I doing it wrong ? EDIT : here is the part of the log that's causing trouble : 2011-08-03 16:28:18 H=(NPI2D389C) [192.168.2.20] F=<[email protected]> rejected RCPT <[email protected]>: relay not permitted The first part ([email protected]) does not matter. I changed the email address. The point is that if this email is @mycompanyemail.com then everything works fine. Anything else does not work. I could add gmail.com, but I am looking to have any domain working...

  Read the article

• Moodle serves on IP only - will not work with mod_proxy

  - by Jon H

  I'm trying to set a moodle server up on an Ubuntu box, which already serves Plone & Trac via Apache. In my Moodle config I have $CFG-wwwroot = 'http://www.server-name.org/moodle' The configuration below works fine for the first two, but when I visit www.server-name.com/moodle I get: Incorrect access detected, this server may be accessed only through "http://xxx.xxx.xxx.xxx:8888/moodle" address, sorry It then forwards to the IP address, where Moodle functions fine. What am I missing to get the server name approach working correctly? Apache Config follows: LoadModule transform_module /usr/lib/apache2/modules/mod_transform.so Listen 8080 Listen 8888 Include /etc/phpmyadmin/apache.conf <VirtualHost xxx.xxx.xxx.xxx:8080> <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On <Location /> ProxyPass http://127.0.0.1:8082/ ProxyPassReverse http://127.0.0.1:8082/ </Location> </VirtualHost> <VirtualHost xxx.xxx.xxx.xxx:80> ServerName www.server-name.org ServerAlias server-name.org ProxyRequests Off FilterDeclare MyStyle RESOURCE FilterProvider MyStyle XSLT resp=Content-Type $text/html TransformOptions +ApacheFS +HTML TransformCache /theme.xsl /home/web/webapps/plone/theme.xsl TransformSet /theme.xsl FilterChain MyStyle ProxyPass /issue-tracker ! ProxyPass /moodle ! <Location /issue-tracker/login> AuthType Basic AuthName "Trac" AuthUserFile /home/web/webapps/plone/parts/trac/trac.htpasswd Require valid-user </Location> Alias /moodle /usr/share/moodle/ <Directory /usr/share/moodle/> Options +FollowSymLinks AllowOverride None order allow,deny allow from all <IfModule mod_dir.c> DirectoryIndex index.php </IfModule> </Directory> </VirtualHost>

  Read the article

• Ctrl + 1 and Ctrl + 2 key combinations don't work

  - by musicfreak

  I noticed back in August (when I got StarCraft 2) that the key combinations Ctrl + 1 and Ctrl + 2 didn't work. I thought this was weird because Ctrl + 3 and all the other combinations worked fine (including Shift + 1, etc), so I didn't think much of it; I just shrugged it off as a SC2 bug. Now, 4 months later, I decided to play a completely unrelated game--Dawn of War 2--and noticed the same thing: those two specific key combinations don't work. To make sure I wasn't going insane, I tried it in Chrome and a couple other applications, and alas, it didn't work. I remember playing strategy games over the summer before StarCraft 2 and it worked fine. Any idea as to what went wrong? My keyboard, a Microsoft Wireless Keyboard 1000 (I know, insert Microsoft joke here), is a little over a year old, so I'm going to assume it's not dying until proven otherwise. Things I've tried ActiveHotkeys says the key combination is not a global hotkey. Tried another keyboard--still doesn't work. The key combinations do work in a virtual machine (tried with both Windows and Ubuntu as guests).

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

• Since upgrading to Windows 8.1, I can't open any files on a SMB share shared by my OS X Mavericks Mac

  - by Gary

  I have a PC with Windows 8.1 and a Mac with Mavericks. I have a folder on the Mac that is shared with the PC. When I'm on the PC and I try to open a file that is shared by the Mac, such as an ISO file (a disk image), then I get a message saying that I cannot open the file, or the file is in use (it depends on the app/filetype). I have the same problem when I open a video file. Strangely, text files and PDF files are just fine. And if I copy any of the problematic files to the local Windows disk, then I can open them just fine. The specific error messages are: AVI files opened in VLC: "Your input can't be opened. VLC is unable to open the MRL." ISO files opened by Windows Explorer: "Sorry, there was a problem mounting the file." This only started happening after I upgraded to Windows 8.1 on the PC and Mavericks on the Mac. Mavericks upgraded its SMB version from SMB1 to SMB2, so perhaps that is related? Does anyone know what the problem might be, and how I could fix it? Thanks in advance!

  Read the article

• Custom flash uploader breaks only on Media Temple

  - by LaserWolf

  I've built a flash uploader to upload files up to 100MB using a php backend. It works wonderfully on our dev server, on a hostgator vps, and on one of our clients' servers running Debian. It will not work on our Media Temple (dv)3.5 and I don't know why. The upload will start but will choke after a few seconds with this flash error message: ioerror: [IOErrorEvent type="ioError" bubbles=false cancelable=false eventPhase=2 text="Error #2038: File I/O Error. URL: http://..._upload.php"] The problem seems to be specific to the asynchronous nature of the flash uploader because if I try a straight php upload it works fine. The php.ini settings are set to allow such a large upload as well. Also, I've thoroughly googled flash, 2038, I/O error, etc but have yet to find anything that helped. Here's the weird part though: We work in Seattle. It won't work from the office. It won't work from home. But, while on the phone with MT's support, they were able to upload a file through our flash uploader just fine. I'm not sure where his office was located but I think it was Atlanta. So the problem also seems specific to physical location. Has anyone run into this sort of problem before?

  Read the article

• Outlook 2007 will not send/receive using RPC over HTTP to an exchange server.. works for other users

  - by bob franklin smith harriet

  I have an incredibly frustrating user issue that I have been unable to resolve for over a week, any ideas for this would be greatly appreciated. The user is having troubles using Outlook 2007 to send or receive emails over using RPC over HTTP (Outlook Anywhere) to an exchange server. Basically what happens, the connection will be establised and the user will be prompted for the username and password, those are submitted and then outlook tries to download emails which fails and the connection to the exchange server will remain unavailable. The machine can ping and everything to the exchange server there is no connection issue there. The setup worked fine for him up untill now and also works for possibly hundreds of other users using the exact same settings, also the same settings will work from the users iphone on the same internet connection, and from my own system using outlook. The exchange server has the webmail https feature and that can be logged into and send and receive emails fine. Steps taken so far: removing the .ost file for the account and allowing office to rebuild it (fixes the issue for a short period of time, then the same symptons occur) deleted exchange profile and recreated (no change in issue) uninstalled all antivirus and firewalls (no change in issue) removed all cached passwords (keymgr.dll) (no change in issue) removed all entries from the hosts file (no change in issue) uninstalled and reinstalled office 2007 (Temporary fix of issue) Installing Symantec Endpoint Client caused a lot of email scan popups to be displayed, after a reboot this stopped and a scan it picked a few trojans that it removed. This fixed the issue temporarily as well, the issue is back again now. I am completely out of ideas now, there seems to be nothing that can be done to fix this issue outside of rebuilding the PC which is a massive pandoras box I don't want to enter with this user. --- Update ---- Malware scans from multiple products have been run on the machine and all updates were installed. The real problem with this user is his distance from us, there is no way to supply a spare laptop or rebuild the machine currently.

  Read the article

• Hyper-V Virtual Machine Networking issues related to Max Ethernet Frame Size

  - by Goatmale

  I fixed an issue today earlier today but i'm interested in learning WHY it worked. We set up a new Hyper-V virtual machine only to discover that HTTP traffic wasn't working. HTTPS, pings, everything else was working fine. After months of prodding around I took a shot in the dark. On the Hyper-V host server, the physical NIC card had an advanced setting of "Max Ethernet Frame Size" set to 1500. After setting this setting to 1514 the issue was fixed. Alternatively, setting this to 1512 did not solve the issue; 1514 is the magic number. My best guess it that when this setting was set to 1500 it was allowing incoming pings because the data payload was a lot smaller of say, HTTP traffic. As far as HTTPS traffic, I read about something called "Path MTU discovery" which i'm going to assume why is HTTPs traffic was getting through fine, albeit slower. Looking at this post, people agree that 1518 is the max total frame size. Why didn't I need to change this to 1518 instead of 1514 bytes? Why is the default frame size 1500 if that's the max size of the Ethernet payload and not the max size.

  Read the article

• File download speed issue over a dedicated fibre link

  - by nixnotwin

  My ISP has installed a fibre based dedicated internet connection at the place where I work. In the beginning the connection terminated at one of the ISP's core routers. It resulted in a strange issue. Eventhough the assigned speed was 5mbps, when tests were done by downloading large files over http and ftp from multiple locations, the speed never went above 2mbps. But bittorrent downloads reached 5mbps. Even file download from the ISP servers were fine. So, at the ISP our link was attached directly to their edge router. After this file downloads from high bandwidth servers, like Google and MS, reached the 5 mbps limit. Sometimes the speed would fall down below 2 mbps and suddenly it will go up to the 5 mbps limit ( it keeps on happening during any single file download). But other downloads like ubuntu apt repositories still struggle to go above 2 mbps. The engineers at the ISP have not been able to sort out the issue. After they moved us to their edge router instead of giving us 8 public ip's, they just gave 4 ip's. When we enquired about it, they told us that giving more ip's would result in arp overload at their edge router. But somehow I was able to convince them to give us the 8 ip's which we wanted. But the file download issue has remained. What might be the reason for files from different location getting downloaded with different speeds, that too with heavy fluctuation in speeds? I have downloaded files from same url's from a connection belonging to another smaller ISP, and the speeds were fine and reached full 5 mbps limit.

  Read the article

• Servers in DMZ will not communicate with each other

  - by Tukaro

  (Full disclosure: I rate barely above "noob" when it comes to networking.) My workplace recent got a new web server. Since we're nearing the end of an overhaul of our website, we're doing a slooooow migration between the old web server and the new one. The old webserver (we'll call it SERVOLD) is Windows Server 2008 with IIS 7. It does not have SQL Server installed. The new server (SERVNEW) is Windows Server 2008 R2, IIS 7.5, with the same version of SQL Server installed. Both are located in the DMZ for our network, and both have their own outward-facing IP address (.3 and .4, respectively). Each server can communicate fine with computers within the domain (not in the DMZ), and those same computers have no trouble communicating with either server. Both servers are also accessible from the internet just fine. However, no matter what, these two servers just refuse to recognize each other. They have the same Workgroup name listed (WORKGROUP), and I thought that would be enough for them to recognize each other. What needs to happen such that I can get these two servers to communicate with each other? We want to do a gradual roll-over to the new website (new one uses ASP.NET, old one uses CFMX), so being able to use one database between both servers is a necessity. Thanks!

  Read the article

• Can't do more than one activity at a time after switching modems

  - by vallorn

  I had to replace the Motorola 2210 DSL modem that I got when I signed up for AT&T DSL Direct a few years ago. The modem kept randomly restarting and it eventually gave out on me. I am assuming overheating was the cause here because it was almost too hot to touch. In any case, I replaced it with a Netgear DM111PSP. It works fine but I can't do more than one activity at a time with it. If my wife is watching Netflix, there is a noticeable delay/latency when trying to view web sites. It's even worse if I try to play an on-line game while she's streaming; the game is basically unplayable. The odd thing is, the only other activity I can do while she's streaming is stream another Netflix show myself. There is no delay when doing that, no buffering either. I'm not a networking guy so maybe there is an explanation for it but I find that kind of odd. I've tried using QoS through my Buffalo N600 wireless router and it doesn't seem to help. With the old Motorola modem, she could be watching Netflix while I play a game and everything worked just fine. Is there anything I can check or reconfigure possibly on the modem that would account for this? Should I just ditch the Netgear and get another modem instead? I have the Netgear modem connected to the Buffalo router in a bridged mode. Its the same exact setup as I had with the Motorola and as far as I can tell, it's not the router that is the cause.

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: Ethernet (see comment) Host network adapter: Wireless (see comment) Guest ethernet network adapter 1: Bridged VMNet (automatic) Guest ethernet network adapter 2: Host only VMNet comment: my host has LAN and Wifi but only one at the same time. I'm either wired or wireless. Never both. So bridged connection on VM goes either via wire or air. Problem When I'm wirelessly connected on the host and I access internet within VM my connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitely but connection won't pick-up automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when host is connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• Xp SP3 - Non-Functioning

  - by Josh

  Ok Here is a crazy problem, I have a HP dv6000 Laptop that can no longer hold a charge, so I hooked it up to my TV, bought a wireless mouse and keyboard and configured xp to run with the lid closed, It has medium to heavy usage mainly just streaming from sites like Netfilx, Hulu, ABC, etc. And playing movies I ripped of dvd. It ran fine for a while but recently it has been having some weird problems: Problem one: I used to use firefox but now when run it I can type but as soon as I click something it just shuts down, completely, I can't even close it unless I use taskmanager to do it. So I went and got google chrome which is better but still hit or miss, but never completely shuts down, I just can't click anything or type anything, or sometimes I just can't type anything or vice versa. Also when I open a new tab, and try to move back to my old one, it automatically closes the old tab when I click on it. Problem two: When using the internet I can't use any other application or anything windows (ie. Windows explorer) until I force quit all browsers with taskmanger. The reason I can't run anything is because I can't click on it. Problem three: When I try to play a movie (with vlc) Once it starts playing I can't click on anything, but I can use hotkeys, and once it stops everything is fine again. Well I hope somebody knows whats going on because I have no clue, If you need clarification or more info on something I would be happy to provide it...

  Read the article

• Windows - Website unaccessible only on windows pcs in LAN

  - by DorentuZ

  For serveral days now, a website isn't accessible on a single pc in the LAN. On the other pc's, it works just fine. And it's just a single website that's not accessible as far as I know of. The website generates a timeout on every single web browser I've tried (IE8, Firefox and Chrome). However, traceroute, nmap and telnet all work just fine. I've even tried multiple user accounts and safe mode, but that didn't work either. As a side note: using a linux live cd did work and I could access the website without any problems. The hosts file is the windows default, the ip- and dns settings on the network adapter normal as well. No strange processes are running and no viruses found. According to tcpview and netstat there are connections to the domain, but every request in the browser results in a timeout.. Any idea what's happening? Update: All of the computers on the network running Windows (any version) are showing this problem now. The website is still working under linux and mac osx. So, it has to be related to some kind of windows update (although I haven't installed any on one computer in the past week, which I've set to do manual updates only)..

  Read the article

• "Path Not Found" when attempting to write to a sub folder within a mapped drive

  - by Adam

  We have an interesting issue with one of our server shares, or possibly, our Win 7 desktops. When our users try to save files in a sub folder, either via copy/paste or through an application, to a mapped drive on our DC they receive an error saying "Path not found". They can however browse this folder and open files from it. This is where the "Path Not Found" error doesn't seem to stack up in my opinion. Users can however save files fine in the root folder of the mapped drive, it appears only to affect sub folders. It seems to be random which users and machines this affects. The users can log on to a different machine and be able to save in sub folders fine, on the same mapped drive. Event viewer hasn't been much help either. Currently, the only solution we have found is to image the machines affected which solves the issue. Our servers are Server 2008 R2 with Win 7 Pro desktops. Any help/pointers/suggestions would greatly be appreciated.

  Read the article

• Running git-svn with cron results in garbage in .git

  - by Paul

  I've setup a git-svn repo with cron to fetch from the svn repo daily. I have a script to do the fetching, and this is what is invoked by cron. Everything is fine with the repo, and the script works fine when executed manually. However, when it runs under cron, empty files get dropped into the .git directory. The files have names that look like they are some base64 output, e.g. juTrvjP6m8 and kcKf3hu3b4. Two of these files show up for every cron run. I thought these might be commit hashes, but they're not, git-show says it's an unknown revision. I set-up the repo as follows: git svn init http://svn.ip.addr/repo git svn fetch svn-remote My script looks like this: cd /gitsvn/dir git svn fetch svn-remote git svn push pub The last line pushes the repo to a separate (bare) public repo from which others can clone. I'm piping the output from the cron job to a file, which looks like this: fatal: unable to run 'git-svn' Counting objects: 21, done. Delta compression using up to 2 threads. Compressing objects: 100% (10/10), done. Writing objects: 100% (11/11), 59.08 KiB, done. Total 11 (delta 8), reused 0 (delta 0) To /gitpub/repo.git 360faf5..a153b0d trunk -> trunk The line "fatal: unable to run 'git-svn'" is alarming, but the fetch seems to go ahead anyway. Any suggestions? Where are these empty garbage files coming from, and how to stop them? Am I in for bigger problems in the future? BTW, I'm using git 1.6.3.3.

  Read the article

• Hyper-V 2008 R2 synthetic networking stops working with linux 2.6.32.15

  - by luxifer

  Hi there, so I thought I'd give Hyper-V on Windows Server 2008 R2 Enterprise a try on my Homeserver (yes, it's legit... got it from msdnaa). First thing to throw at it was my firewall which runs IPFire. This distribution currently uses the kernel version 2.6.32.15 and comes with the Hyper-V drivers. So I enabled them and at first they work just fine but after a few minutes they just fail. There are no packages going in or out anymore until I reboot the VM but sometimes even that won't work so the VM just keeps "Stopping" like forever. Emulated networking works fine but it slow and uses more CPU. That way my firewall routes slower than when running under virtualbox on an atom N270. My server has an E6750; VM is limited to 25%, but that should still outperform this atom CPU especially since it's never going anywhere near 100% CPU load, so give me a break! A quick google search led me to people having the same problem (even with other distributions and kernel versions that include those drivers) but no solution yet... I already found this but I can't quite follow the author on the part where he solved the issue - especially since I need two virtual nics for my firewall distro to work (obviously one internal and one external) What am I missing here?

  Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >