Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 127/216 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

  - by Jander

  I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

  Read the article

• Routing table on Linux not respected

  - by MRHaarmann

  I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

  Read the article

• Can't display RSSI values in Wireshark

  - by Giovanni Soldi

  I am trying to analyze the up-link Wireless traffic generated by my Sony Ericsson phone and captured by my D-Link router, on which I installed the DD-WRT firmware. To do this, first I log in the router and enable the prism0 interface by typing the command: wl -i eth1 monitor 1 and then I start to capture the packets by typing: tcpdump -i prism0 ether src xx:xx:xx:xx:xx:xx -s0 -w /tmp/smbshare/sony_ericsson_test.pcap where xx:xx:xx:xx:xx:xx is the MAC address of my Sony Ericsson phone. After a while I transfer the sony_ericsson_test.pcap file to my computer and open it with Wireshark program. In order to display the RSSI values I follow this procedure: Edit - Preferences... - Columns - Press "Add" button - As "Field type" I choose "IEEE 802.11 RSSI" and finally I choose name "Power" and click on "Apply" button. The problem is that the column "Power" is empty with no RSSI values. Does Anyone has a clue on why are RSSI values not displayed? Maybe I am missing a passage. Looking forward to hearing from anyone of you! Thanks in advance for your help!

  Read the article

• Road Warrior VPN Setup

  - by wobblycogs

  I apologise up front for the rather open ended nature of this question but I've got well out of my depth and could really do with some pointers. I need to set up a road warrior VPN solution which will allow our customers to securely access a number of services we provide for them. Customer machines will be running a variety of Windows versions from XP onwards with a variety of patch levels. Typically they will connect from the clients main offices but not always. It is safe to assume that all clients will be behind NATs but we may occasionally see a connection that isn't NAT'ed. Typical connection situation is therefore: Customer Laptop -- Router (NAT) -- Internet -- VPN Server + Firewall -- Server (Win 2008 R2, Non-routable IP) There will initially be a dozen or so people that could connect but that will grow quickly to around 100. It's unlikely that we'll see that many concurrent connections though, I imagine our total VPN throughput would be <50Mbps peak. What are my options for setting this up? I've been trying to set up a system like this using a MikroTik router for a few days but have struggled to get it working correctly, particularly with NAT'ed clients. I've had a quick look at OpenVPN and liked what I saw but I think it's unlikely our customers IT departments would allow the client to be installed. Finally I've looked at the Cisco ASA range but I'm on a fairly tight budget so this is less preferable but it looks like it would work pretty much out of the box. My fall back position is to connect the server directly and use the provided VPN + Firewall facilities but that is far from ideal as the number of servers is likely to grow over time.

  Read the article

• Weirdly high ping on direct ethernet connection?

  - by Antriel

  I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• using gmail as email relay for sendmail

  - by Nikita

  I used to be able to send emails using a gmail account & sendmail configured using one of the guides on the Internet, for example: http://appgirl.net/blog/configuring-sendmail-to-relay-through-gmail-smtp/ This is a small server and I've recently moved it to a different house. And sendmail has stop working. The only thing different in the network setup is a new router. What is happening: In the log files, I see the following error: ...stat=Deferred: smtp.gmail.com: No route to host When I run from the command line: strace sendmail -f A -t B -u "Subject" -m "Message" -tls=yes ssl=yes -s smtp.gmail.com:587 -xu A -xp XYZ It hangs on this call: recvfrom(3, "m0\201\203\0\1\0\0\0\0\0\0\4ares\3lan\0\0\34\0\1", 8192, 0, {sa_family=AF_INET, sin_port=htons(53), sin_addr=inet_addr("192.168.1.254")}, [16]) = 26 close(3) = 0 time(NULL) = 1339997943 open("/etc/localtime", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb76ff000 read(3, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0\0\0\0"..., 4096) = 3477 _llseek(3, -24, [3453], SEEK_CUR) = 0 read(3, "\nEST5EDT,M3.2.0,M11.1.0\n", 4096) = 24 close(3) = 0 munmap(0xb76ff000, 4096) = 0 socket(PF_FILE, SOCK_DGRAM|SOCK_CLOEXEC, 0) = 3 connect(3, {sa_family=AF_FILE, path="/dev/log"}, 110) = 0 send(3, "<18>Jun 18 01:39:03 sendmail[268"..., 96, MSG_NOSIGNAL) = 96 nanosleep({60, 0}, So it looks like at some point it tries to resolve the DNS name, but I don't have anything running on 53, so it dies out and then just hangs. The other interesting thing is that msmtp works just fine on the same server. Update: ares in strace output is actually the name of my server, but .254 IP address is the address of the router. Could anyone tell me why this is happening or what further steps can I take to investigate the issue? Thanks!

  Read the article

• Instructions to setup primary and only domain controller

  - by Robert Koritnik

  Where could I get best step by step instructions (with some simple explanations) how to setup domain controller on Windows Server 2008 R2 Server Core? I don't know what do I need? Do I need DNS as well and AD and so on and so forth. I don't know enough about these things, but I need to set them up to prepare development environment. I would also like to know how to configure firewall on DC machine, to make it visible on other machines because I've setup DC somehow but I can't connect to it... This is my HW config: Linksys internet router with DHCP my dev machine is Windows 7 my DC machine is a VM in my dev machine my dev machine has a hw network adapter to linksys and a virtual network adapter to DC DC machine has two network adapters: one to linksys (to be internet connected so it can be updated etc.) and one to host (my dev Win7 machine) Edit My development machine should access domain controller and logon using domain credentials. Development machine would access internet directly via Linksys router. My domain controller machine would only serve authentication (and if I'm able to configure it right) should also have Active Directory Federation Services in a workable condition. I hope this is a bit more clear now. At least a small bit.

  Read the article

• How to stop NAT dropping idle connections?

  - by WGH

  I have a TCP connection that can be idle for many hours. The traffic is flowing from the server to the client only. One might say it's kind of push notification. My home router, however, tends to drop the connection silently after 20 minutes (the value of /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established). The server detects the loss once it tries to send anything (I assume it receives RST from the router itself). As client never sends anything, it never detects the loss. RFC 5382 "NAT Behavioral Requirements for TCP" states the following: A NAT can check if an endpoint for a session has crashed by sending a TCP keep-alive packet and receiving a TCP RST packet in response. It makes sense. It's much more effective than sending keep-alives by the host itself (as only NAT knows its own timeout). And probably not hard to implement. Is there any NAT solutions implementing this? It would be great if there was a way to enable this in iptables.

  Read the article

• Why do I need a managed switch and which one should I buy?

  - by ascanio1

  I bought a 2nd router and I want both routers to have direct WAN access to the modem. One of the 2 routers directs VOIP traffic to a telephone line port. This VOIP service is provided by the cable carrier which also leases the modem & the router. The cable company technician told me that this VOIP line uses IPv6 addressing and therefore I must employ an IPv6 capable/compliant Giga Hub/Switch or my telephone line won't work anymore. Pls advise me (brand/model) an IPv6 compliant, 2 port, switch to purchase. Pls educate me: By reading this forum I thought that hubs broadcast traffic to all ports, regardless of which input/output is being used and so, theoretically, they have nothing to do with IP. Correct? Same story for unmanaged switches, where the only difference is that these latter devices route traffic only to those ports which are detected to be in use. Correct? I also understood that unmanaged switches route traffic simply by detecting hardware use and not by selecting specific IP traffic. Correct? Finally, there are managed switches which DO select traffic based on IP and, therefore, only these managed switches are involved with IPv6... Why would my cable company explicitly tell me, over and over, that I must use an IPv6 compliant switch? Why would they need a managed switch instead of an unmanaged one? Thanks in advance for helping me understand!

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• Setup windows 2012 AD in Hyper-V for a Test environment

  - by hub

  Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

  Read the article

• How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

  - by Aesir

  I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

  Read the article

• How can I make IPv6 on OpenVPN work using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 server side (set as gateway on client) 2001:db8::100:abc:2 tap0 client side 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

• How can I setup OpenVPN with IPv4 and IPv6 using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 (on server) (set as gateway on client) 2001:db8::100:abc:2 tap0 (on client) 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). net.ipv6.conf.all.forwarding is set to 1, I've tried disabling net.ipv6.conf.all.accept_ra as well, without luck. Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

• Apache local verses external (domain)

  - by Jessy Houle

  I have an Apache server running on Ubuntu server 10, using Passenger for Ruby on Rails. I have configured my site under the sites-enabled directory of Apache and can hit the server with an internal IP address (192.168.X.X) and the site comes back as expected. However, whenever I try to hit the site externally, either through the domain name or the IP address tied to the domain name, the site will not come back. I have a router in the middle with a static IP address, with Port Forwarding turned on (forwarding 80/443) to the server and I'm quite confident the issue isn't there. In fact, I even DMZed to the Ubuntu Server just to make sure. Also, all router firewall options have been turned off. So here is the question... Is there something else I have to do with Ubuntu server to allow externally requested port 80 traffic? Otherwise, is there some settings that need to be set in Apache to allow domain or external IP address port 80 traffic through? I'm pretty new to Apache, so, please take it a bit easy on me :-) Thank you for your responses. -Jessy Houle

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• Find routers IP address on the other side

  - by corsiKa

  Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

  Read the article

• Can I autoregister my servers hostname in my local DNS? [on hold]

  - by Christian Wattengård

  We have evaluated a W2k12 server as a domain controller at work. This has the extra benefit of registering every "subordinate" computers name in it's DNS so that I don't have to go around remembering IP's all the time. (And it let's me easily run dhcp also on my "pop-up" dev-servers). We need to rework our work network for several odd reasons, and in this new scenario there was no money for an extra Windows 2012 license. We have at our disposal several old boxes that run linux quite well. Is it possible to set up a DNS-server-"appliance" that somehow autoregisters it's own hostname.. Scenario: Router (N66u) on 172.20.20.1. Runs DHCP on 172.20.20.100-200 range. Server [verdant] of a *nix flavor on 172.20.20.2 Laptop [speedy] of W8 flavor on DHCP assigned Laptop [canary] of W8 flavor on DHCP assigned Desktop [lianyu] of Ubuntu flavor on DHCP assigned What I would like is that all of the above servers (except possibly the router) would be available on verdant.starling.lan and canary.starling.lan and so on. This is how it works right now (except the Ubuntu box... I haven't cracked that one yet) because Windows just does this for you.. I would also be able to do this without any manual labor on the server. When I tell my box it's name is smoak it should "immediately" be available as smoak.starling.lan without any extra configuration on my part. How can I do this in a Linux (Ubuntu) environment?

  Read the article

• Freshly installed dd-wrt on dir-300 and no internet. What to do?

  - by Erik B

  With the d-link firmware I just connected the router and it worked, as is expected when using DHCP, but with dd-wrt I have no internet access. It is configured with DHCP, and dd-wrt's wan status page reports that it is connected and that it has an ip address. Yet it is impossible to reach the internet. If I disconnect the router and plugs the cable directly into my computer I get internet access, so it's obviously the dd-wrt software that isn't doing its job. However, I have no previous experience with the dd-wrt software and have no clue what to look for. I thought it would just work. By the way, the power led is orange, the internet led is off, and wireless+lan1 is green. They all used to be green with the d-link firmware. Not sure if it's relevant, but now you know. Does anyone have any idea what I should do to get internet access (besides reinstalling d-link's firmware)? EDIT: It's a version B1. I read that it is very different from the A1 version, so I thought it may be relevant.

  Read the article

• Ubuntu: Network connection seems to fail after some time

  - by chrischu

  I just bought a Shuttle XS-35 barebone mini-PC and put a 1 TB WD hard drive and 2 Gigs of RAM into it and installed Ubuntu onto it. The machine will post as a media server (streaming videos to my PS3) and as a webserver for some small private projects. Now I wanted to copy my videos from my Windows 7 machine to the Ubuntu machine and therefore created a Samba share on the Ubuntu machine. I tried copying the files with the standard Windows copy function and with SyncToy but after some time (sometimes 5 copied files, sometimes 120 copied files) the Samba share just disappears. When that happens I can't reach the internet from the Ubuntu machine although the network connection still seems to be fine (IP still there etc.). Between the machines lies a LinkSys router. When I try to ping my router (after the connection doesn't work anymore) from the Ubuntu machine only a very small subset of the packages actually get there (something around 20%). When I restart the Ubuntu machine everything seems to work normal again. I have no idea where the problem lies here. Does anybody have a clue? Thanks in advance!

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

• Change source address based on destination IP

  - by hgj

  We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

  Read the article

• SSH connection times out unless I tunnel in from a different server-

  - by rm-vanda

  OK, so this just started last week - Whenever we try to connect to our server via ssh (we use sftp, as well) - The connection times out. However, when you ssh to any other server and then ssh into the machine - it works flawlessly. Now, the mindblowing thing is that sometimes the ssh connection will succeed. Moments ago, I tried it from another machine, and then my own, and it worked - only to time out the next go around. Last week, simply restarting the ssh daemon worked, but this week, no such luck. I even went in and changed: /etc/hosts.allow ALL : ALL and /etc/hosts.deny is blank. The firewall config hasn't changed - but I even disabled the firewall to see if that would work - It did, for a moment - before cutting off, again. (ufw is set to "ALLOW" not "LIMIT") When I try SSH'ing in from my phone -- it works, fine -- So, it seems the problem is with our ISP/router/gateway - However, I see no log in the router/gateway that says its blocking our connections - And that wouldn't explain why we can SSH into any other server -- except for this one - from our network --- I truly appreciate any insight that anyone may have on this matter -

  Read the article

• Slow upload, fast download on Windows 7 64bit system

  - by Malik

  I've got a weird problem in the download speeds on my desktop PC (Windows 7 Home Premium 64bit) are consistently fast (approx. 400kB/s) but uploads are very slow (around 6-10kB/s). This has been going on for the last 3 weeks or so. I am a very competent user and troubleshooter, and have searched online for 2 weeks for a solution, to no avail. Part of the problem is that internet is provided by WiFi by my landlord and I have no access to the router (BT Home Hub router) although I know for sure he wouldn't have the first idea on how to restrict my usage :) (rules that out) Anyway, I've tried: - various drivers (my Wifi 'card' is TP-link TL-WN851N, and I've tried TP-link + Atheros + Qualcomm Atheross drivers, suggested by Microsoft) - various tweaks to network parameters (e.g. as suggested by SpeedOptimser) - various tweaks to Windows 7 services (e.g. disabling/manual-ing unecessary services) - raising and lowering head onto a reasonably firm surface at moderate frequency (jk :D) None of the above have helped, and I'm officialy asking for help now!! Thanks for your time and effort in advance!

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >