Search Results

Search found 3266 results on 131 pages for 'dell dimension'.

Page 127/131 | < Previous Page | 123 124 125 126 127 128 129 130 131  | Next Page >

  • Ubuntu 11 and 12 initially fast but later bogs down, CPU pegged

    - by uos??
    I started with Ubuntu 11 a few weeks ago. It's on a DELL M4300 with a OCZ SSD. Default setup, except that I've installed the proprietary NVIDIA graphics and BROADCOM wireless drivers. Dual boot with Windows. If I cold boot into Ubuntu, it is very fast, just like the Windows experience that I'm used to. But SOMETHING happens, and I haven't yet determined what, but the system gets incredibly slow and stays that way. At first I thought it had to do with Adobe Flash because it seemed to be triggered by sites with Flash. But then I removed Flash and the problem remains. I thought it was just an overheating problem, but I've now upgraded to 12.04 which supposedly fixes the overheating problems I've read about. Perhaps the heat situation was brought on by Flash in my early cases? So I installed Jupiter for CPU management, but the thermometer reports a familiar Windows-side temperature of 53 degrees Celsius. Switching Jupiter to lower performance doesn't help. When I check the System Monitor application, sorting by CPU usage, there are no obvious problem processes. However, in the graphs tab, both CPU cores are pegged at 100%! I notice that the slowness seems to be similar to the extremely bad performance I got prior to installing the NVIDIA drivers. I'm not sure if that helps. This is the strangest part to me - although the temperature seems OK, even after rebooting, the system remains slow - starting with GRUB2 which is very noticeably delayed, all the way through to either Ubuntu or Windows! That's right, even the Windows side suffers effects and takes several minutes to complete booting whereas normally (with my SSD) it's ready to use in 15 seconds. The only way to fix it is to shutdown and let the parts cool down. Or maybe it just needs to completely power off and boot rather than a soft reboot, temperature has nothing to do with it? - is that possible? But know that I have never had this problem in Windows, even if Windows gets very hot (135 F) a reboot would be enough time for it to recover. For this reason, I don't think it's a heat thing, but I can't imagine what else could be surviving the reboot. I'm entirely updated - there are no pending updates. I have the Post-Release updates of NVIDIA too, btw. If this sounds CLOSE to something you know about, but one of the details doesn't line up exactly, it might be a mistake in my perception. Are there tests you can suggest to rule something out? Thanks! processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5187.00 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5186.94 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: (Redundant figures removed. You can view them in the edits if they are still relevant) ps: %CPU PID USER COMMAND 9.4 2399 jason gnome-terminal 6.2 2408 jason bash 17.3 1117 root /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none 13.7 1667 jason compiz 1.3 1960 jason /usr/lib/unity/unity-panel-service 1.3 1697 jason python /usr/bin/jupiter 0.9 1964 jason /usr/lib/indicator-appmenu/hud-service 0.6 1689 jason nautilus -n 0.4 1458 jason //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session I should highlight specifically that GRUB2 can also be very slow. I don't know the relationship of which scenarios GRUB2 is also slow, but WHEN it is slow, it is slow both before the menu appears and after the selection is made - although for the diagnosis of GRUB2 it is harder for me to tell what the normal speeds should be. With SSD, I would expect that GRUB2 could load instantly, and that the GRUB2 purple would disappear instantly after the selection. The only delay to be expected is the change in graphics modes (though I couldn't guess why that ever requires any noticeable time)

    Read the article

  • OTN Architect Day Headed to Reston, VA - May 16

    - by Bob Rhubart
    In 2011 OTN Architect Day made stops in Chicago, Denver, Phoenix, Redwood Shores, and Toronto. The 2012 series begins with OTN Architect Day in Reston, VA on Wednesday May 16. Registration is now open for this free event, but don't get caught napping -- seating is limited, and the event is just 5 weeks away. The information below reflects the most recent updates to the event agenda, including the addition of Oracle ACE Director Kai Yu as the guest keynote speaker. Kai is Senior System Engineer / Architect at Dell, Inc., and has been very busy of late as a speaker at various industry and Oracle User Group events. I'm very happy Kai has agreed to make the trek from his hometown in Austin, TX to share his insight at the Architect Day event in Reston.  If you're in the area, put this one on your calendar. You won't be sorry.   Venue Sheraton Reston Hotel 11810 Sunrise Valley Drive Reston, VA 20191 Event Agenda 8:30 am - 9:00 am Registration and Continental Breakfast 9:00 am - 9:15 am Welcome and Opening Comments 9:15 am - 10:00 am Engineered Systems: Oracle's Vision for the Future | Ralf Dossman Oracle's Exadata and Exalogic are impressive products in their own right. But working in combination they deliver unparalleled transaction processing performance with up to a 30x increase over existing legacy systems, with the lowest cost of ownership over a 3 or 5 year basis than any other hardware. In this session you'll learn how to leverage Oracle's Engineered Systems within your enterprise to deliver record-breaking performance at the lowest TCO. 10:00 am - 10:30 am High Availability Infrastructure for Cloud Computing | Kai Yu Infrastructure high availability is extremely critical to Cloud Computing. In a Cloud system that hosts a large number of databases and applications with different SLAs, any unplanned outage can be devastating, and even a small planned downtime may be unacceptable. This presentation will discuss various technology solutions and the related best practices that system architects should consider in cloud infrastructure design to ensure high availability. 10:30 am - 10:45 am Break 10:45 am - 11:30 am Breakout Sessions: (pick one) Innovations in Grid Computing with Oracle Coherence | Bjorn Boe Learn how Coherence can increase the availability, scalability and performance of your existing applications with its advanced low-latency data-grid technologies. Also hear some interesting industry-specific use cases that customers had implemented and how Oracle is integrating Coherence into its Enterprise Java stack. Cloud Computing - Making IT Simple | Scott Mattoon The road to Cloud Computing is not without a few bumps. This session will help to smooth out your journey by tackling some of the potential complications. We'll examine whether standardization is a prerequisite for the Cloud. We'll look at why refactoring isn't just for application code. We'll check out deployable entities and their simplification via higher levels of abstraction. And we'll close out the session with a look at engineered systems and modular clouds. 11:30 pm - 12:15 pm Breakout Sessions: (pick one) Oracle Enterprise Manager | Joe Diemer Oracle Enterprise Manager (EM) provides complete lifecycle management for the cloud - from automated cloud setup to self-service delivery to cloud operations. In this session you'll learn how to take control of your cloud infrastructure with EM features including Consolidation Planning and Self-Service provisioning with Metering and Chargeback. Come hear how Oracle is expanding its management capabilities into the cloud! Rationalization and Defense in Depth - Two Steps Closer to the Clouds | Dave Chappelle Security represents one of the biggest concerns about cloud computing. In this session we'll get past the FUD with a real-world look at some key issues. We'll discuss the infrastructure necessary to support rationalization and security services, explore architecture for defense -in-depth, and deal frankly with the good, the bad, and the ugly in Cloud security. 12:15 pm - 1:15 pm Lunch 1:40 pm - 2:00 pm Panel Discussion - Q&A 2:00 pm - 2:45 pm Breakout Sessions: (pick one) 21st Century SOA | Peter Belknap Service Oriented Architecture has evolved from concept to reality in the last decade. The right methodology coupled with mature SOA technologies has helped customers demonstrate success in both innovation and ROI. In this session you will learn how Oracle SOA Suite's orchestration, virtualization, and governance capabilities provide the infrastructure to run mission critical business and system applications. And we'll take a special look at the convergence of SOA & BPM using Oracle's Unified technology stack. Track B: Oracle Cloud Reference Architecture | Anbu Krishnaswamy Cloud initiatives are beginning to dominate enterprise IT roadmaps. Successful adoption of Cloud and the subsequent governance challenges warrant a Cloud reference architecture that is applied consistently across the enterprise. This presentation gives an overview of Oracle's Cloud Reference Architecture, which is part of the Cloud Enterprise Technology Strategy (ETS). Concepts covered include common management layer capabilities, service models, resource pools, and use cases. 2:45 pm - 3:00 pm Break 3:00 pm - 4:00 pm Roundtable Discussions 4:00 pm - 4:15 pm Closing Comments & Readouts from Roundtable 4:15 pm - 5:00 pm Cocktail Reception / Networking Session schedule and content subject to change.

    Read the article

  • CodePlex Daily Summary for Tuesday, October 15, 2013

    CodePlex Daily Summary for Tuesday, October 15, 2013Popular ReleasesFFXIV Crafting Simulator: Crafting Simulator 2.4.1: -Fixed the offset for the new patch (Auto Loading function)iBoxDB.EX - Fast Transactional NoSQL Database Resources: iBoxDB.net fast transactional nosql database 1.5.2: Easily process objects and documents, zero configuration. fast embeddable transactional nosql document database, includes CURD, QueryLanguage, Master-Master-Slave Replication, MVCC, etc. supports .net2, .net4, windows phone, mono, unity3d, node.js , copy and run. http://download-codeplex.sec.s-msft.com/Download?ProjectName=iboxdb&DownloadId=737783 Benchmark with MongoDB Compatibility more platforms for java versionneurogoody: slicebox: this is the slice box jsEvent-Based Components AppBuilder: AB3.AppDesigner.55: Iteration 55 (Feature): Moving of TargetEdge (simple wires only) by mouse.Sandcastle Help File Builder: SHFB v1.9.8.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This new release contains bug fixes and feature enhancements. There are some potential breaking changes in this release as some features of the Help File Builder have been moved into...SharpConfig: SharpConfig 1.2: Implemented comment parsing. Comments are now part of settings and setting categories. New properties: Setting: Comment PreComments SettingCategory: Comment PreCommentsC++ REST SDK (codename "Casablanca"): C++ REST SDK 1.3.0: This release fixes multiple customer reported issues as well as the following: Full support for Dev12 binaries and project files Full support for Windows XP New sample highlighting the Client and Server APIs : BlackJack Expose underlying native handle to set custom options on http_client Improvements to Listener Library Note: Dev10 binaries have been dropped as of this release, however the Dev10 project files are still available in the Source CodeAD ACL Scanner: 1.3.2: Minor bug fixed: Powershell 4.0 will report: Select—Object: Parameter cannot be processed because the parameter name p is ambiguous.Json.NET: Json.NET 5.0 Release 7: New feature - Added support for Immutable Collections New feature - Added WriteData and ReadData settings to DataExtensionAttribute New feature - Added reference and type name handling support to extension data New feature - Added default value and required support to constructor deserialization Change - Extension data is now written when serializing Fix - Added missing casts to JToken Fix - Fixed parsing large floating point numbers Fix - Fixed not parsing some ISO date ...RESX Manager: ResxManager 0.2.1: FIXED: Many critical bugs have been fixed. New Features Error logging for improved exception handling New toolbar Improvements of user interfaceFast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Wsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.TerrariViewer: TerrariViewer v7 [Terraria Inventory Editor]: This is a complete overhaul but has the same core style. I hope you enjoy it. This version is compatible with 1.2.0.3 Please send issues to my Twitter or https://github.com/TJChap2840WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...MoreTerra (Terraria World Viewer): MoreTerra 1.11.3: =========== =New Features= =========== New Markers added for Plantera's Bulb, Heart Fruits and Gold Cache. Markers now correctly display for the gems found in rock debris on the floor. =========== =Compatibility= =========== Fixed header changes found in Terraria 1.0.3.1Media Companion: Media Companion MC3.581b: Fix in place for TVDB xml issue. New* Movie - General Preferences, allow saving of ignored 'The' or 'A' to end of movie title, stored in sorttitle field. * Movie - New Way for Cropping Posters. Fixed* Movie - Rename of folders/filename. caught error message. * Movie - Fixed Bug in Save Cropped image, only saving in Pre-Frodo format if Both model selected. * Movie - Fixed Cropped image didn't take zoomed ratio into effect. * Movie - Separated Folder Renaming and File Renaming fuctions durin...SmartStore.NET - Free ASP.NET MVC Ecommerce Shopping Cart Solution: SmartStore.NET 1.2.0: HighlightsMulti-store support "Trusted Shops" plugins Highly improved SmartStore.biz Importer plugin Add custom HTML content to pages Performance optimization New FeaturesMulti-store-support: now multiple stores can be managed within a single application instance (e.g. for building different catalogs, brands, landing pages etc.) Added 3 new Trusted Shops plugins: Seal, Buyer Protection, Store Reviews Added Display as HTML Widget to CMS Topics (store owner now can add arbitrary HT...New ProjectsArtezio SharePoint 2013 Workflow Activities: SharePoint Workflow 2013 doesn’t provide activities to work with permissions, we've fixed it using HttpSend activity that makes REST API calls.Dependency.Injection: An attempt to write a really simple dependency injection framework. Does property-based and recursive dependency injection. Handles singletons. Yay!DHGMS SUO Killer: SUO Killer is a Visual Studio extension to deal with the removal of SUO file to mitigate SUO related issues in Visual Studio. This project is written in C#.dynamicsheet: dynamicsheetExcel Comparator: Excel Comparator is an add-in for Microsoft Excel that allows the user to compare a range between two sheets. FetchAIP: FetchAIP is a utility to download the various sections of the Aeronautical Information Publication (AIP) for New Zealand.Fluent Method and Type Builder: Still working on the summary.getboost: NuGet package for Boost framework.Goldstone Forum: WebForms Forum - TelerikAcademy Team ProjectGroupMe Software Development Kit: .NET Software Development Kit for http://groupme.com/ chat service.GSLMS: ----Import Excel Files Into SQL Server: Load Excel files into SQL Database without schema changes.Inaction: ?????????? jBegin: Learning ASP.net MVC from beginning, then here will be the source code for jbegin.comKDG's Statistical Quality Control Solver: This tool will include methods that can solve sample standard deviation, sample variance, median, mode, moving average, percentiles, margin of error, etc.kpi: Key Performance Indicator (KPI)????; visual studio 2010 with .NET 4.0 runtimeLECO Remote Control Client Application: Sample code and binaries are provided to demonstrate the remote control capability of a LECO Cornerstone instrument.LinkPad: My first Windows Store app intended for student to sketch up thoughts and concepts in quick diagrams.Modler.NET - Automating Graphical Data Model Co-Evolution: Modler.NET was the tool created for a Master's thesis project, which automates the co-evolution of graphical data models and the database that they represent.MyFileManager1: SummaryNever Lotto: Korean 465 Lotto Analyzer and Simulator. The real purpose of this project is to show that this kind of lotto things are just shit.NHibernate: The purpose of this project is to demo CRUD operations using NHibernate with Mono in Visual Studio 2012 using C# language. OAuth2 Authorizer: OAuth2 Authorizer helps you get the access code for a standard OAuth2 REST service that implements 3-legged authentication.Regular Expression for Excel: Regular Expression For Excel is an Excel Plugin. It provides a regular expressions EXCEL support. We can use it in the EXCEL function.Service Tester: Service Tester is an Azure Cloud based load testing application targeted at Soap Web Services which allows you to invoke your Web Service by random parameters.Simple TypeScript and C# Class Generator: Simple GUI application to generate compatible class source code for C# and TypeScript for communications between C# and TypeScript. Soccer team management: ---Spanner: No more stringly-typed web development! Build statically typed single page web applications in C#, automatically generating all HTML, JavaScript, and Knockout.

    Read the article

  • Superpower Your Touchpad Computer with Scrybe

    - by Matthew Guay
    Are you looking for a way to help your Touchpad computer make you more productive?  Here’s a quick look at Scrybe, a new application from Synaptics that lets you superpower it. Touchpad devices have become increasingly more interesting as they’ve included support for multi-touch gestures.  Scrybe takes it to the next level and lets you use your touchpad as an application launcher.  You can launch any application, website, or complete many common commands on your computer with a simple gesture.  Scrybe works with most modern Synaptics touchpads, which are standard on most laptops and netbooks.  It is optimized for newer multi-touch touchpads, but can also work with standard single-touch touchpads.  It works on Windows 7, Vista, and XP, so chances are it will work with your laptop or netbook. Get Started With Scrybe Head over to the Scrybe website and download the latest version (link below).  You are asked to enter your email address, name, and information about your computer…but you actually only have to enter your email address.  Click Download when finished. Run the installer when it’s download.  It will automatically download the latest Synaptics driver for your touchpad and any other components needed for Scrybe.  Note that the Scrybe installer will ask to install the Yahoo! toolbar, so uncheck this to avoid adding this worthless browser toolbar. Using Scrybe To open an application or website with a gesture, press 3 fingers on your touchpad at once, or if your touchpad doesn’t support multi-touch gestures, then press Ctrl+Alt and press 1 finger on your touchpad.  This will open the Scrype input pane; start drawing a gesture, and you’ll see it on the grey square.  The input pane shows some default gestures you can try. Here we drew an “M”, which opens our default Music player.  As soon as you finish the gesture and lift up your finger, Scrybe will open the application or website you selected. A notification balloon will let you know what gesture was preformed. When you’re entering your gesture, the input pane will show white “ink”.  The “ink” will turn blue if the command is recognized, but will turn red if it isn’t.  If Scrybe doesn’t recognize your command, press 3 fingers and try again. Scrybe Control Panel You can open the Scrybe Control panel to enter or change commands by entering a box-like gesture, or right-clicking the Scrybe icon in your system tray and selecting “Scrybe Control Panel”. Scrybe has many pre-configured gestures that you can preview and even practice. All of the gestures in the Popular tab are preset and cannot be changed.  However, the ones in the favorites tab can be edited.  Select the gesture you wish to edit, and click the gear icon to change it.  Here we changed the email gesture to open Hotmail instead of the default Yahoo Mail. Scrybe can also help you perform many common Windows commands such as Copy and Undo.  Select the Tools tab to see all of these commands.   Scrybe has many settings you may wish to change.  Select the Preferences button in the Control Panel to change these.  Here’s some of the settings we changed. Uncheck “Display a message” to turn off the tooltip notifications when you enter a gesture Uncheck “Show symbol hints” to turn off the sidebar on the input pane Select the search engine you want to open with the Search Gesture.  The default is Yahoo, but you can choose your favorite. Adding a new Scrybe Gesture The default Scrybe options are useful, but the best part is that you can assign gestures to your own programs or websites.  Open the Scrybe control panel, and click the plus sign on the bottom left corner.  Enter a name for your gesture, and then choose if it is for a website or an application. If you want the gesture to open a website, enter the address in the box. Alternately, if you want your gesture to open an application, select Launch Application and then either enter the path to the application, or click the button beside the Launch field and browse to it. Now click the down arrow on the blue box and choose one of the gestures for your application or website. Your new gesture will show up under the Favorites tab in the Scrybe control panel, and you can use it whenever you want from Scrybe, or practice the gesture by selecting the Practice button. Conclusion If you enjoy multi-touch gestures, you may find Scrybe very useful on your laptop or netbook.  Scrybe recognizes gestures fairly easily, even if you don’t enter them perfectly correctly.  Just like pinch-to-zoom and two-finger scroll, Scrybe can quickly become something you miss on other laptops. Download Scrybe (registration required) Similar Articles Productive Geek Tips Fixing Firefox Scrolling Problems with Dell Synaptics TouchpadRemove Synaptics Touchpad Icon from System TrayRoll Back Troublesome Device Drivers in Windows VistaChange Your Computer Name in Windows 7 or VistaLet Somebody Use Your Computer Without Logging Off in Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Fun with 47 charts and graphs Tomorrow is Mother’s Day Check the Average Speed of YouTube Videos You’ve Watched OutlookStatView Scans and Displays General Usage Statistics How to Add Exceptions to the Windows Firewall Office 2010 reviewed in depth by Ed Bott

    Read the article

  • Searching for the Perfect Developer&rsquo;s Laptop.

    - by mbcrump
    I have been in the market for a new computer for several months. I set out with a budget of around $1200. I knew up front that the machine would be used for developing applications and maybe some light gaming. I kept switching between buying a laptop or a desktop but the laptop won because: With a Laptop, I can carry it everywhere and with a desktop I can’t. I searched for about 2 weeks and narrowed it down to a list of must-have’s : i7 Processor (I wasn’t going to settle for an i5 or AMD. I wanted a true Quad-core machine, not 2 dual-core fused together). 15.6” monitor SSD 128GB or Larger. – It’s almost 2011 and I don’t want an old standard HDD in this machine. 8GB of DDR3 Ram. – The more the better, right? 1GB Video Card (Prefer NVidia) – I might want to play games with this. HDMI Port – Almost a standard on new Machines. This would be used when I am on the road and want to stream Netflix to the HDTV in the Hotel room. Webcam Built-in – This would be to video chat with the wife and kids if I am on the road. 6-Cell Battery. – I’ve read that an i7 in a laptop really kills the battery. A 6-cell or 9-cell is even better. That is a pretty long list for a budget of around $1200. I searched around the internet and could not buy this machine prebuilt for under $1200. That was even with coupons and my company’s 10% Dell discount. The only way that I would get a machine like this was to buy a prebuilt and replace parts. I chose the  Lenovo Y560 on Newegg to start as my base. Below is a top-down picture of it.   Part 1: The Hardware The Specs for this machine: Color :  GrayOperating System : Windows 7 Home Premium 64-bitCPU Type : Intel Core i7-740QM(1.73GHz)Screen : 15.6" WXGAMemory Size : 4GB DDR3Hard Disk : 500GBOptical Drive : DVD±R/RWGraphics Card : ATI Mobility Radeon HD 5730Video Memory : 1GBCommunication : Gigabit LAN and WLANCard slot : 1 x Express Card/34Battery Life : Up to 3.5 hoursDimensions : 15.20" x 10.00" x 0.80" - 1.30"Weight : 5.95 lbs. This computer met most of the requirements above except that it didn’t come with an SSD or have 8GB of DDR3 Memory. So, I needed to start shopping except this time for an SSD. I asked around on twitter and other hardware forums and everyone pointed me to the Crucial C300 SSD. After checking prices of the drive, it was going to cost an extra $275 bucks and I was going from a spacious 500GB drive to 128GB. After watching some of the SSD videos on YouTube I started feeling better. Below is a pic of the Crucial C300 SSD. The second thing that I needed to upgrade was the RAM. It came with 4GB of DDR3 RAM, but it was slow. I decided to buy the Crucial 8GB (4GB x 2) Kit from Newegg. This RAM cost an extra $120 and had a CAS Latency of 7. In the end this machine delivered everything that I wanted and it cost around $1300. You are probably saying, well your budget was $1200. I have spare parts that I’m planning on selling on eBay or Anandtech.  =) If you are interested then shoot me an email and I will give you a great deal mbcrump[at]gmail[dot]com. 500GB Laptop 7200RPM HDD 4GB of DDR3 RAM (2GB x 2) faceVision HD 720p Camera – Unopened In the end my Windows Experience Rating of the SSD was 7.7 and the CPU 7.1. The max that you can get is a 7.9. Part 2: The Software I’m very lucky that I get a lot of software for free. When choosing a laptop, the OS really doesn’t matter because I would never keep the bloatware pre-installed or Windows 7 Home Premium on my main development machine. Matter of fact, as soon as I got the laptop, I immediately took out the old HDD without booting into it. After I got the SSD into the machine, I installed Windows 7 Ultimate 64-Bit. The BIOS was out of date, so I updated that to the latest version and started downloading drivers off of Lenovo’s site. I had to download the Wireless Networking Drivers to a USB-Key before I could get my machine on my wireless network. I also discovered that if the date on your computer is off then you cannot join the Windows 7 Homegroup until you fix it. I’m aware that most people like peeking into what programs other software developers use and I went ahead and listed my “essentials” of a fresh build. I am a big Silverlight guy, so naturally some of the software listed below is specific to Silverlight. You should also check out my master list of Tools and Utilities for the .NET Developer. See a killer app that I’m missing? Feel free to leave it in the comments below. My Software Essential List. CPU-Z Dropbox Everything Search Tool Expression Encoder Update Expression Studio 4 Ultimate Foxit Reader Google Chrome Infragistics NetAdvantage Ultimate Edition Keepass Microsoft Office Professional Plus 2010 Microsoft Security Essentials 2  Mindscape Silverlight Elements Notepad 2 (with shell extension) Precode Code Snippet Manager RealVNC Reflector ReSharper v5.1.1753.4 Silverlight 4 Toolkit Silverlight Spy Snagit 10 SyncFusion Reporting Controls for Silverlight Telerik Silverlight RadControls TweetDeck Virtual Clone Drive Visual Studio 2010 Feature Pack 2 Visual Studio 2010 Ultimate VS KB2403277 Update to get Feature Pack 2 to work. Windows 7 Ultimate 64-Bit Windows Live Essentials 2011 Windows Live Writer Backup. Windows Phone Development Tools That is pretty much it, I have a new laptop and am happy with the purchase. If you have any questions then feel free to leave a comment below.  Subscribe to my feed

    Read the article

  • Surface and the Uphill Battle to Win Over iPad Users (Namely: Me)

    - by D'Arcy Lussier
    I went away this past weekend and decided to bring along the Windows 8 tablet from the Build conference last year – y’know, to give Windows 8 a try in a typical scenario. I also brought our iPad 2 along since I figured my wife would want to use that. I’d love to tell you how I found using my Windows 8 tablet but I can’t – I used the iPad exclusively the entire weekend. It was during this that I realized what Microsoft needs to do to win me over as an iPad user. As you’ll see, I’m left wondering what it is that Surface is meant to compete with: iPad and other tablets, or thin laptops like the MacBook Air or Ultrabooks. Device Size I really like the size of the iPad compared with the Build tablet. It’s not as long and the thinness/weight of the device makes it feel more like you’re holding a magazine than a computer. I’m pleased that Microsoft will be matching the thinness of the iPad with Surface, but I’m suspect as to what that actually means. The iPad’s edges slant inwards where the Surface has a thicker boxish look (similar to the iPhone 4S). So while they may have the same depth at the deepest part of both devices, I bet the iPad will come off feeling thinner. However, its not lost on me the number of external port options the Surface’s design provides over the iPad (Usb, etc.). With that said, I haven’t missed having a USB slot on my iPad. I’m not a fan of lengthening the Surface screen size to almost a full inch over the iPad, mainly because… Vertical Orientation Experience Did you notice at the announce event, in the images of the devices that have been released, and in any marketing for it, that the surface is always displayed in horizontal orientation. This is a huge beef I have with my Build tablet and why I prefer the iPad. Yes the iPad can do the wide-screenish mode, but the iPad is oriented to be vertical by nature. Don’t agree? Look at the button and camera placement – both on the shorter sides of the device. Compare that with the Surface, where the orientation for the button and camera is on the longer sides. To be fair, Blackberry and the horde of Android tablets out there haven’t gotten this either – since most monitors are widescreen nowadays tablets should be too right? Wrong. Widescreen is great for certain things, but tasks such as reading is not one of them – hence why monitor companies like Dell provide stands that allow you to flip your widescreen monitor to a vertical orientation. That Microsoft has chosen a horizontal orientation by default for Windows 8 is disappointing – hopefully hardware manufacturers will be given the option of a default vertical orientation. Fast Startup Time I like that I can turn off/turn on the iPad very quickly. Even from a true “off” mode and not just sleeping, the iPad boots up very quickly. Windows RT needs to have that same quick response. If I start finding that I’m waiting for the device to boot up for more than 30 seconds that could be a show stopper. No Heat I really hate that the Build tablet has fans that kick in to cool the procs, but its basically a slate computer and I get its part of that prototype build. For Surface, it needs to be the same type of experience as the iPad – no heat! I know Surface doesn’t have fans and uses some cool new vent system or something like that, but even then – I want to sit and read a book on my Surface without having to feel any heat coming from the device, which is the experience I have with the iPad now. What About Apps?! I am definitely not the target client when it comes to app stores. On my iPad I use: Safari Kindle Reader Twitter App Settlers of Catan TSN’s App And that’s it. So really, while its nice that some version of Office might be available, I’m not planning on utilizing a Surface for creating a PowerPoint or working on a Word document – that’s what my laptop is for. I want my tablet to be for information snacking or as an e-reader and occasionally an entertainment device. Surface vs iPad or Surface vs Air? The more that I read up on Surface, the more I wonder if it won’t be a touch-enabled MacBook Air competitor more than an iPad one. Also, I really question if Microsoft gets tablets – when one of your main selling features is a built-in physical keyboard it speaks more to a traditional laptop experience than a tablet one that’s entirely reliant on touch. Still, I really love the Windows Phone interface – way more than iOS – so I’m still very optimistic that the Metro experience on the tablet will be fantastic. I just worry that Microsoft has interpreted a tablet as a computer with a removable keyboard and a touch screen, and that’s not what tablet computing is about at all.

    Read the article

  • CodePlex Daily Summary for Thursday, December 13, 2012

    CodePlex Daily Summary for Thursday, December 13, 2012Popular ReleasesHome Access Plus+: v8.6: v8.6.1213.1220 Added: Group look up to the visible property of the Booking System Fixed: Switched to using the outlook/exchange thumbnailPhoto instead of jpegPhoto Added: Add a blank paragraph below the tiles. This means that the browser displays a vertical scroller when resizing the window. Previously it was possible for the bottom edge of a tile not to be visible if the browser window was resized. Added: Booking System: Only Display Day+Month on the booking Home Page. This allows for the cs...Layered Architecture Solution Guidance (LASG): LASG 1.0.0.8 for Visual Studio 2012: PRE-REQUISITES Open GAX (Please install Oct 4, 2012 version) Microsoft® System CLR Types for Microsoft® SQL Server® 2012 Microsoft® SQL Server® 2012 Shared Management Objects Microsoft Enterprise Library 5.0 (for the generated code) Windows Azure SDK (for layered cloud applications) Silverlight 5 SDK (for Silverlight applications) THE RELEASE This release only works on Visual Studio 2012. Known Issue If you choose the Database project, the solution unfolding time will be slow....Torrents-List Organizer: Torrents-list organizer v 0.5.0.3: ????????? ? 0.5.0.3: 1) ?????????? ??????? ??? ?????????? ???-??????? ? ???????-??????. 2) ? ??????? ?????? ??????????? ?????????????? ????? ?????????? ?????????: ???? ?? ??????-???? ?????????? ?? ????????? ?? ????? ???????, ?? ? ????? ????? ????????? ????? ????????? ?? ????, ? ????????? ??? ???? ?????? ??????????.Fiskalizacija za developere: FiskalizacijaDev 2.0: Prva prava produkcijska verzija - Zakon je tu, ova je verzija uskladena sa trenutno važecom Tehnickom specifikacijom (v1.2. od 04.12.2012.) i spremna je za produkcijsko korištenje. Verzije iza ove ce ovisiti o naknadnim izmjenama Zakona i/ili Tehnicke specifikacije, odnosno, o eventualnim greškama u radu/zahtjevima community-a za novim feature-ima. Novosti u v2.0 su: - That assembly does not allow partially trusted callers (http://fiskalizacija.codeplex.com/workitem/699) - scheme IznosType...Simple Injector: Simple Injector v1.6.1: This patch release fixes a bug in the integration libraries that disallowed the application to start when .NET 4.5 was not installed on the machine (but only .NET 4.0). The following packages are affected: SimpleInjector.Integration.Web.dll SimpleInjector.Integration.Web.Mvc.dll SimpleInjector.Integration.Wcf.dll SimpleInjector.Extensions.LifetimeScoping.dllBootstrap Helpers: Version 1: First releasesheetengine - Isometric HTML5 JavaScript Display Engine: sheetengine v1.2.0: Main featuresOptimizations for intersectionsThe main purpose of this release was to further optimize rendering performance by skipping object intersections with other sheets. From now by default an object's sheets will only intersect its own sheets and never other static or dynamic sheets. This is the usual scenario since objects will never bump into other sheets when using collision detection. DocumentationMany of you have been asking for proper documentation, so here it goes. Check out the...DirectX Tool Kit: December 11, 2012: December 11, 2012 Ex versions of DDSTextureLoader and WICTextureLoader Removed use of ATL's CComPtr in favor of WRL's ComPtr for all platforms to support VS Express editions Updated VS 2010 project for official 'property sheet' integration for Windows 8.0 SDK Minor fix to CommonStates for Feature Level 9.1 Tweaked AlphaTestEffect.cpp to work around ARM NEON compiler codegen bug Added dxguid.lib as a default library for Debug builds to resolve GUID link issuesArcGIS Editor for OpenStreetMap: ArcGIS Editor for OSM 2.1 Final for 10.1: We are proud to announce the release of ArcGIS Editor for OpenStreetMap version 2.1. This download is compatible with ArcGIS 10.1, and includes setups for the Desktop Component, Desktop Component when 64 bit Background Geoprocessing is installed, and the Server Component. Important: if you already have ArcGIS Editor for OSM installed but want to install this new version, you will need to uninstall your previous version and then install this one. This release includes support for the ArcGIS 1...SharpCompress - a fully native C# library for RAR, 7Zip, Zip, Tar, GZip, BZip2: SharpCompress 0.8.2: This release just contains some fixes that have been done since the last release. Plus, this is strong named as well. I apologize for the lack of updates but my free time is less these days.Media Companion: MediaCompanion3.511b release: Two more bug fixes: - General Preferences were not getting restored - Fanart and poster image files were being locked, preventing changes to themVodigi Open Source Interactive Digital Signage: Vodigi Release 5.5: The following enhancements and fixes are included in Vodigi 5.5. Vodigi Administrator - Manage Music Files - Add Music Files to Image Slide Shows - Manage System Messages - Display System Messages to Users During Login - Ported to Visual Studio 2012 and MVC 4 - Added New Vodigi Administrator User Guide Vodigi Player - Improved Login/Schedule Startup Procedure - Startup Using Last Known Schedule when Disconnected on Startup - Improved Check for Schedule Changes - Now Every 15 Minutes - Pla...Secretary Tool: Secretary Tool v1.1.0: I'm still considering this version a beta version because, while it seems to work well for me, I haven't received any feedback and I certainly don't want anyone relying solely on this tool for calculations and such until its correct functioning is verified by someone. This version includes several bug fixes, including a rather major one with Emergency Contact Information not saving. Also, reporting is completed. There may be some tweaking to the reporting engine, but it is good enough to rel...CAML Builder: CAML Builder 1.0.0.0: First public release of CAML BuilderVidCoder: 1.4.10 Beta: Added progress percent to the title bar/task bar icon. Added MPLS information to Blu-ray titles. Fixed the following display issues in Windows 8: Uncentered text in textbox controls Disabled controls not having gray text making them hard to identify as disabled Drop-down menus having hard-to distinguish white on light-blue text Added more logging to proxy disconnect issues and increased timeout on initial call to help prevent timeouts. Fixed encoding window showing the built-in pre...WPF Application Framework (WAF): WPF Application Framework (WAF) 2.5.0.400: Version 2.5.0.400 (Release): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Changelog Legend: [B] Breaking change; [O] Marked member as obsolete Update the documentation. InfoMan: Write the documentation. Other Downloads Downloads Overviewlog4net Dynamics CRM 2011 Appender: log4net Dynamics CRM 2011 Appender DLL: log4net Dynamics CRM 2011 Appender DLLBee OPOA Platform: Bee OPOA Demo V1.0.001: Initial version.postleitzahlensuche: Plz Suche: Eine C# Wpf Applikation, welche ermöglicht nach Postleitzahlen oder Orten zu suchen und als Ergebnis sowohl die Postleitzahl als auch den Ort liefert.Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.78: Fix for issue #18924 - using -pretty option left in ///#DEBUG blocks. Fix for issue #18980 - bad += optimization caused bug in resulting code. Optimization has been removed pending further review.New ProjectsBing Maps WPF Viewer: A helpful multi layer map viewer tool. Features (more soon) : * Tile layers XYZ format * MS SQL Server spatial layerBizTalk Business Rules Engine Pipeline Framework: The BizTalk BRE Pipeline Framework provides increased flexibility in development and maintenance of pipeline components by leveraging the Business Rules Engine.Bootstrap Helpers: Html Helpers for creating Twitter Bootstrap ControlsChord Analizer: Component to help user to analizing chord of a songCodeStudyX: The learning materials of programming.faiztest22: Kudu testingFizzEdit: A multilingual code editor written in C#.FlowDOS: gGDI WebServices: Este projecto está relacionado com a cadeira de Gestão de Dados e Informação, mestrado de Sistema de Informação (Universidade de Aveiro). 2012HyperLinq - Multidimensional LINQ: HyperLINQ is an extension to LINQ that supports multidimensional arrays without dimension limit.ImageTools for WinRT: This is a poring project, so for more details information, pls refer to Sebastian Stehle's page: http://imagetools.codeplex.com/JavuHD - 2D Evolved.: An Amazing next generation High Definition 2D sdk for C#/.Net that uses OpenCL to accelerate a wide variety of features and rendering operations. All in one.MVC ActionValidator: Infrastructure for bisness validationNosso Rico Dinheirinho: Financial control system like Microsoft Money, but via web.Open Song to Chord Pro converter: A converter to convert sheet music from the Open Song format to the Chord Pro formatOpenXML Word AltChunk: Using ALTCHUNK with OPENXML and SharePoint.Project : Afspraaksysteem voor dokters (oefening opleiding Sharepoint & .Net): Een planningsysteem gemaakt door de developers van lokaal 105, in opdracht van Erdem Yarici. Dit in het kader van een Cevora/VDAB Sharepoint & .NET-opleiding.project13271213: 11SIPAS: Support Sip Client Call to FreeswitchSmall Deterministic Embedded Assembler Register Machine: SIDEARM is a minimal, virtual register machine that acts as an interpreter/shell for valid AVR assembly language execution in real-time by the virtual machine.studyx: The learning materials of programming.Unused File Detector: A small program that detects any files not used by Visual Studio solutions.Web.Ajax: Web.Ajax is an AJAX library for the .NET framework. It is designed to make it easy to add ajax functionality to an application. Windows Azure Diagnostics to SQL: Copy Windows Azure Diagnostics (WAD) data from Azure Tables to SQL server to allow for a familiar querying interface.

    Read the article

  • Build 2012, some thoughts..

    - by Dennis Vroegop
    I think you probably read my rant about the logistics at Build 2012, as posted here, so I am not going into that anymore. Instead, let’s look at the content. (BTW If you did read that post and want some more info then read Nia Angelina’s post about Build. I have nothing to add to that.) As usual, there were good speakers and some speakers who could benefit from some speaker training. I find it hard to understand why Microsoft allows certain people on stage, people who speak English with such strong accents it’s hard for people, especially from abroad, to understand. Some basic training might be useful for some of them. However, it is nice to see that most speakers are project managers, program managers or even devs on the teams that build the stuff they talk about: there was a lot of knowledge on stage! And that means when you ask questions you get very relevant information. I realize I am not the average audience member here, I am regular speaker myself so I tend to look for other things when I am in a room than most audience members so my opinion might differ from others. All in all the knowledge of the speakers was above average but the presentation skills were most of the times below what I would describe as adequate. But let us look at the contents. Since the official name of the conference is Build Windows 2012 it is not surprising most of the talks were focused on building Windows 8 apps. Next to that, there was a lot of focus on Azure and of course Windows Phone 8 that launched the day before Build started. Most sessions dealt with C# and JavaScript although I did see a tendency to use C++ more. Touch. Well, that was the focus on a lot of sessions, that goes without saying. Microsoft is really betting on Touch these days and being a Touch oriented developer I can only applaud this. The term NUI is getting a bit outdated but the principles behind it certainly aren’t. The sessions did cover quite a lot on how to make your applications easy to use and easy to understand. However, not all is touch nowadays; still the majority of people use keyboard and mouse to interact with their machines (or, as I do, use keyboard, mouse AND touch at the same time). Microsoft understands this and has spend some serious thoughts on this as well. It was all about making your apps run everywhere on all sorts of devices and in all sorts of scenarios. I have seen a couple of sessions focusing on the portable class library and on sharing code between Windows 8 and Windows Phone 8. You get the feeling Microsoft is enabling us devs to write software that will be ubiquitous. They want your stuff to be all over the place and they do anything they can to help. To achieve that goal they provide us with brilliant SDK’s, great tooling, a very, very good backend in the form of Windows Azure (I was particularly impressed by the Mobility part of Azure) and some fantastic hardware. And speaking of hardware: the partners such as Acer, Lenovo and Dell are making hardware that puts Apple to a shame nowadays. To illustrate: in Bellevue (very close to Redmond where Microsoft HQ is) they have the Microsoft Store located very close to the Apple Store, so it’s easy to compare devices. And I have to say: the Microsoft offerings are much, much more appealing that what the Cupertino guys have to offer. That was very visible by the number of people visiting the stores: even on the day that Apple launched the iPad Mini there were more people in the Microsoft store than in the Apple store. So, the future looks like it’s going to be fun. Great hardware (did I mention the Nokia Lumia 920? No? It’s brilliant), great software (Windows 8 is in a league of its own), the best dev tools (Visual Studio 2012 is still the champion here) and a fantastic backend (Azure.. need I say more?). It’s up to us devs to fill up the stores with applications that matches this. To summarize: it is great to be a Windows developer. PS. Did I mention Surface RT? Man….. People were drooling all over it wherever I went. It is fantastic :-) Technorati Tags: Build,Windows 8,Windows Phone,Lumia,Surface,Microsoft

    Read the article

  • CodePlex Daily Summary for Wednesday, October 16, 2013

    CodePlex Daily Summary for Wednesday, October 16, 2013Popular ReleasesHyper-V Management Pack Extensions 2012: HyperVMPE 2012 (1.0.1.206): RTM ReleaseFFXIV Crafting Simulator: Crafting Simulator 2.4: Added : - You can now drag&drop to reorganize the sequence. (Right click to remove now) - Fixed a bug with Ingenuity II not taken into consideration for quality Increase.C# Intellisense for Notepad++: Release v.1.0.8.2: Solved scrolling problem after DocumentFormatting Implemented "format as you type" --- To avoid the DLLs getting locked by OS use MSI file for the installation.CS-Script for Notepad++ (C# intellisense and code execution): Release v1.0.8.2: Solved scrolling problem after DocumentFormatting Implemented "format as you type" --- To avoid the DLLs getting locked by OS use MSI file for the installation.Collection Commander for Configuration Manager 2012: CMCollCtr 1.0.0: Change log: - MSI Setup - UI Improved - CM12 Console integration - New Powershell code snippets - Client Center IntegrationLINQ to Twitter: LINQ to Twitter v2.1.09: Supports .NET 3.5, .NET 4.0, .NET 4.5, Silverlight 4.0, Windows Phone 7.1, Windows Phone 8, Client Profile, Windows 8, and Windows Azure. 100% Twitter API coverage. Also supports Twitter API v1.1! Also on NuGet.Sandcastle Help File Builder: SHFB v1.9.8.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This new release contains bug fixes and feature enhancements. There are some potential breaking changes in this release as some features of the Help File Builder have been moved into...AD ACL Scanner: 1.3.2: Minor bug fixed: Powershell 4.0 will report: Select—Object: Parameter cannot be processed because the parameter name p is ambiguous.Json.NET: Json.NET 5.0 Release 7: New feature - Added support for Immutable Collections New feature - Added WriteData and ReadData settings to DataExtensionAttribute New feature - Added reference and type name handling support to extension data New feature - Added default value and required support to constructor deserialization Change - Extension data is now written when serializing Fix - Added missing casts to JToken Fix - Fixed parsing large floating point numbers Fix - Fixed not parsing some ISO date ...RESX Manager: ResxManager 0.2.1: FIXED: Many critical bugs have been fixed. New Features Error logging for improved exception handling New toolbar Improvements of user interfaceFast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Wsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.TerrariViewer: TerrariViewer v7 [Terraria Inventory Editor]: This is a complete overhaul but has the same core style. I hope you enjoy it. This version is compatible with 1.2.0.3 Please send issues to my Twitter or https://github.com/TJChap2840WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...Free language translator and file converter: Free Language Translator 3.4: fixes for new version look up.MoreTerra (Terraria World Viewer): MoreTerra 1.11.3: =========== =New Features= =========== New Markers added for Plantera's Bulb, Heart Fruits and Gold Cache. Markers now correctly display for the gems found in rock debris on the floor. =========== =Compatibility= =========== Fixed header changes found in Terraria 1.0.3.1Media Companion: Media Companion MC3.581b: Fix in place for TVDB xml issue. New* Movie - General Preferences, allow saving of ignored 'The' or 'A' to end of movie title, stored in sorttitle field. * Movie - New Way for Cropping Posters. Fixed* Movie - Rename of folders/filename. caught error message. * Movie - Fixed Bug in Save Cropped image, only saving in Pre-Frodo format if Both model selected. * Movie - Fixed Cropped image didn't take zoomed ratio into effect. * Movie - Separated Folder Renaming and File Renaming fuctions durin...New ProjectsCDEasyUI: CDEasyUIEnough XamlConverter: A collection of useful XAML converters for Windows Phone and Windows 8 developers alike.GeReS: Geres is a simple batch job manager for Azure, written in Python for general applicability. Global Excel Automation Powershell Library: The Global Excel Automation PowerShell Library is a series of scripts to help with build deployment, application configuration, database copies and Hyper-V.jean1016jabbrchang: 11katrukTestProject: katruk test projectLocal to Global Option Set Converter: Automates the task of converting a Local Option Set into a Global Option Set in Microsoft Dynamics CRM 2011.Machine Cards: Machine Cards is a card playing game!Microsoft Translator Portable Wrapper: A portable wrapper for Microsoft Translator service. Can be used in various apps types. Desktop apps(.Net Framework 4.5), Windows Phone 8, Windows Store apps.Mod.DisplayTypes: Orchard module for a url that display content items with a certain display type. Multilingual Translator & Dictionary: The Multilingual Translator & Dictionary can translate and search meanings of words / phrases in multiple languages using Google Translator and Glosbe APIs.nDistribute: This is an attempt to build a library for synchronising data across a network of machines without the use of a predetermined central server.neurogoody: js sliceboxNotepadXX: NotepadXX is one of the requirements to complete in Open source. It is a open source text editor software.ODTK: Ein Toolkit für das Rollenspiel "Das Schwarze Auge (Ulisses Verlag)" um manche abläufe beim Spielen zu vereinfachen. Kampf Übersicht, Helden DBPhoto Frame and Door Cam: A Windows Service that hosts a simple digital photo frame web page that integrates with the Blue Iris NVR to show camera alerts when motion is detected.Powershell XML Deployment: While working as a Windows Server technology specialist in Sweden in the outsourcing branch, i've discovered that people have poor since of automation.PulseMonitor: this is pulse media projectRentACarRESTApi: Rent A Car REST ApiRubricaSentimentale: testScrutR - Monitor entities and notifiy when changes: ScrutR monitors entities of an application and sends notification when the conditions are matchedSRMongoDB: ????MongoDB C# ???。 ?????QueryBuilder.cs??。TP1_Quimica: uiuuuWake On LAN Gateway: A Client/Server solution for relaying WOL magic packets. Server runs as IIS module or Windows Service. Usage via REST service or installable windows client.Weather Forecast - Team Pixie - Telerik Academy 2012/2013: Simple weather forecast sharing website.Webapplication1: WebApplication1

    Read the article

  • Unable to keep the connecting using a wireless bridge

    - by dan
    I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

    Read the article

  • Demantra 7.3.1.3 Controlling MDP_MATRIX Combinations Assigned to Forecasting Tasks Using TargetTaskSize

    - by user702295
    New 7.3.1.3 parameter: TargetTaskSize Old parameter: BranchID  Multiple, deprecated  7.3.1.3 onwards Parameter Location: Parameters > System Parameters > Engine > Proport   Default: 0   Engine Mode: Both   Details: Specifies how many MDP_MATRIX combinations the analytical engine attempts to assign to each forecasting task.  Allocation will be affected by forecsat tree branch size.  TaskTargetSize is automcatically calculated.  It holds the perferred branch size, in number of combinations in the lowest level. This parameter is adjusted to a lower value for smaller schemas, depending on the number of available engines.   - As the forecast is generated the engine goes up the tree using max_fore_level and not top_level -1.  Max_fore_level has     to be less than or equal to top_level -1.  Due to this requirement, combinations falling under the same top level -1     member must be in the same task.  A member of the top level -1 of the forecast tree is known as a branch.  An engine     task is therefore comprised of one or more branches.     - Reveal current task size       go to Engine Administrator --> View --> Branch Information and run the application on your Demantra schema.  This will be deprecated in 7.3.1.3 since there is no longer a means of adjusting the brach size directly.  The focus is now on proper hierarchy / forecast design.     - Control of tasks       The number of tasks created is the lowest of number of branches, as defined by top level -1 members in forecast       tree, and engine sessions and the value of TargetTaskSize.  You are used to using the branch multiplier in this       calculation.  As of 7.3.1.3, the branch ID multiple is deprecated.     - Discovery of current branch size       To resolve this you must review the 2nd highest level in the forecast tree (below highest/highest) as this is the       level which determines the size of the branches.  If a few resulting tasks are too large it is recommended that       the forecast tree level driving branches be revised or at times completely removed from the forecast tree.     - Control of foreacast tree branch size         - Run the following sql to determine how even the branches are being split by the engine:             select count(*),branch_id from mdp_matrix where prediction_status = 1 and do_fore = 1 group by branch_id;             This will give you an understanding if some of the individual branches have an unusually large number of           rows and thus might indicate that the engine is not efficiently dividing up the parallel tasks.         - Based on the results of this sql, we may want to adjust the branch id multiplier and/or the number of engines           (both of these settings are found in the Engine Administrator)           select count(*), level_id from mdp_matrix where prediction_status = 1 and do_fore = 1 group by level_id;           This will give us an understanding at which level of the Forecast tree where the forecast is being generated.            Having a majority of combinations higher on the forecast tree might indicate either a poorly designed forecast           tree and/or engine parameters that are too strict           Based on the results of this we would adjust the Forecast Tree to see if choosing a different hierarchy might           produce a forecast, with more combinations, at a lower level.           For example:             - Review the 2nd highest level in the forecast tree, below highest/highest, as this is the level which               determines the size of the branches.             - If a few resulting tasks are too large it is recommended that the forecast tree level driving branches               be revised or at times completely removed from the forecast tree.               - For example, if the highest level of the forecast tree is set to Brand/All Locations.             - You have 10 brands but 2 of the brands account for 67% and 29% of all combinations.             - There is a distinct possibility that the tasks resulting from these 2 branches will be too large for               a single engine to process.  Some possible solutions could be to remove the Brand level and instead               use a different product grouping which has a more even distribution, possibly Product Group.               - It is also possible to add a location dimension to this forecast tree level, for example Customer.                This will also reduce forecast tree branch size and will deliver a balanced task allocation.             - A correctly configured Forecast Tree is something that is done by the Implementation team and is               not the responsibility of Oracle Support.  Allocation will be affected by forecast tree branch size.  When TargetTaskSize is set to 0, the default value, the system automatically calculates a value for 'TargetTaskSize' depending on the number of engines.   - QUESTION:  Does this mean that if TargetTaskSize is 1, we use tree branch size to allocate branches to tasks instead                of automatically calculating the size?     ANSWER: DEV Strongly recommends that the setting of TargetTaskSize remain at the DEFAULT of ZERO (0).   - How to control the number of engines?     Determine how many CPUs are on the machine(s) that is (are) running the engine.  As mentioned earlier, the general     rule is that you should designate 2 engines per each CPU that is available.  So for example, if you are running the     engine on a machine that has 4 CPU then you can have up to 8 engines designated in the Engine Administrator.  In this     type of architecture then instead of having one 'localhost' in your Engine Settings Screen, you would have 'localhost'     repeated eight times in this field.     Where do I set the number of engines?                 To add multiples computers where engine will run, please do a back-up of Settings.xml file under         Analytical Engines\bin\ folder, then edit it and add there the selected machines.                 Example, this will allow 3 engines to start:         - <Entry>           <Key argument="ComputerNames" />           <Value type="string" argument="localhost,localhost,localhost" />           </Entry Otherwise, if there are no additional engines defined, the calculated value of 'TargetTaskSize' is used. (Oracle does not recommend changing the default value.) The TargetTaskSize holds the engines prefered branch size, in number of level 1 combinations.   - Level 1 combinations, known as group size The engine manager will use this parameter to attempt creating branches with similar size.   * The engine manager will not create engines that do not have a branch. The engine divider algorithm uses the value of 'TargetTaskSize' as a system-preferred branch size to create branches that are more equal in size which improves engine performance.  The engine divider will try to add as many tasks as possible to an existing branch, up to the limit of 'TargetTaskSize' level 1 combinations, before adding new branches. Coming up next: - The engine divider - Group size - Level 1 combinations - MAX_FORE_LEVEL - Engine Parameters  

    Read the article

  • CodePlex Daily Summary for Friday, October 18, 2013

    CodePlex Daily Summary for Friday, October 18, 2013Popular ReleasesVoya Media: Voya Media v. 1.2.255: Voya Media is free, open-source and provides one central place to play and organize all your music, pictures and videos. Voya Media | Twitter | Facebook | Google+ Features: Scans disk drives and network shares for valid media files. Generates playlist tags based on directory names. Supports MP3 tags and cover images. Supports built-in and external SRT/SUB subtitles. Gets TV Show episode details from the tvrage.com API. Gets Movie details from the themoviedb.org API. Supports Med...Aphid: Aphid 0.1.0.17 Alpha: Added several samples Fixed + operator bugpatterns & practices - Windows Azure Guidance: Cloud Design Patterns: 1st drop of Cloud Design Patterns project. It contains 14 patterns with 6 related guidance.Media Companion: Media Companion MC3.582b: New* Both - Added 'An' as option to ignore in title * Movie - Renaming - added %Z - Sorttitle to Legend * Movie - Renaming - added %O - Audio Channels to Legend * Movie - Remove a poster source from priority list. Reset List back to defaults. * Made Media Companion truly portable application. Fixed* Movie - browse for Poster Or Fanart, allows for jpg, tbn, png and bmp images * Movie - Alt Fanart Browser - Url or Browse window now fully visible. * Movie - Manual renaming checks if 'Use Fold...Json.NET: Json.NET 5.0 Release 8: Fix - Fixed not writing string quotes when QuoteName is falsePowerShell Community Extensions: 3.1 Production: PowerShell Community Extensions 3.1 Release NotesOct 17, 2013 This version of PSCX supports Windows PowerShell 3.0 and 4.0 See the ReleaseNotes.txt download above for more information.SQL Power Doc: Version 1.0.2.1: Misc. bug fixes Added logic to resolve members of a Windows Group server login Added columns to Excel workbooks to show definitions for server permissions, server roles, database permissions, and database rolesNB_Store - Free DotNetNuke Ecommerce Catalog Module: NB_Store v2.3.8 Rel1: v2.3.8 Is now DNN6 and DNN7 compatible NOTE: NB_Store v2.3.8 is NOT compatible with DNN5. SOURCE CODE : https://github.com/leedavi/NB_Store (Source code has been moved to GitHub, due to issues with codeplex SVN and the inability to move easily to GIT on codeplex)Social Network Importer for NodeXL: SocialNetImporter(v.1.9): This new version includes: - Download latest status update and use it as vertex tooltip - Limit the timelines to parse to me, my friends or both - Fixed some reported bugs about the fan page and group importer - Fixed the login bug reported latelyTerrariViewer: TerrariViewer v7.1 [Terraria Inventory Editor]: You can now backspace in number fields Items added in 1.2.0.3 no longer corrupt player files Buff durations capped at 9999999 Item stacks capped at 9999999 Version info added Prefix IDs corrected Shoe and Eye color box are now properly clickable Moved Bank and Safe into their own tab Users will now be notified of new updatesPython Tools for Visual Studio: 2.0: PTVS 2.0 We’re pleased to announce the release of Python Tools for Visual Studio 2.0 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, IPython, and cross platform and cross language debugging support. QUICK VIDEO OVERVIEW For a quick overview of the general IDE experience, please watch this v...Collection Commander for Configuration Manager 2012: CMCollCtr 1.0.0: Change log: - MSI Setup - UI Improved - CM12 Console integration - New Powershell code snippets - Client Center IntegrationSandcastle Help File Builder: SHFB v1.9.8.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This new release contains bug fixes and feature enhancements. There are some potential breaking changes in this release as some features of the Help File Builder have been moved into...Fast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Wsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...Free language translator and file converter: Free Language Translator 3.4: fixes for new version look up.New ProjectsA Program to Calculate the Sum of Two Numbers: Dennis Gaya - University of HertfordshireAllow users to change their Active Directory password from SharePoint 2013: Allow users to change their Active Directory password from SharePoint 2013 user menu contextAutoCAD Code Pack: AutoCADCodePack is a powerful library that help you to develop AutoCAD plugins using the AutoCAD .NET API.Core Engine: A game engine, written by engineers, for engineers.EmeraldForum: A simple forumFcdbas: FcdbasFreedom: ...High School Behaviour Log: A web based tool for recording student detentions, behaviour issues as well as referrals and positive behaviour. Integrated with school's SIMS.net MIS system.htmlcxx unicode version: thanks for Davi de Castro Reis and Robson Braga Ara?o's work. also thanks for Kasper Peeters 's tree.hhLets Learn DirectX 11.1 Series: Lets Learn DirectX 11.1 is a project run by Ernest Loveland to make knowledge about DirectX 11.1 development more public and freely available.Migrate CPPUnit to VS2013: migrate CPPUnit to VS2013Poll System: Poll system for educational purposePort Layer: ????????,???????R.M.B: JUST XIXIRecetas_LosBorbotones: Recetas Los BorbotonesScrolltastic-Skin: Imagine A Free DotNetNuke responsive Skin, Which Will Make Your Wishes Come True. Sharepoint and web service: This is Sharepoint 2010 project, after deploy it, you can use javascript (ajax) to access sharepoint list, call a custom web service. Everything are very easy!SourceSareProject: 00TestWebApi: WebApi serviceTFSBuildMonitor: Application that in its current shape let you monitor build queues and finished builds in an easier way than what is possible throug the built in Build ExplorerTigerProjects: This project is to create a online RSS reader similar as Google ReaderVottReader: It is project simple reader and viewer for http://vott.ru site.WinFormStudy: C#??

    Read the article

  • CodePlex Daily Summary for Monday, October 14, 2013

    CodePlex Daily Summary for Monday, October 14, 2013Popular ReleasesAD ACL Scanner: 1.3.2: Minor bug fixed: Powershell 4.0 will report: Select—Object: Parameter cannot be processed because the parameter name p is ambiguous.Json.NET: Json.NET 5.0 Release 7: New feature - Added support for Immutable Collections New feature - Added WriteData and ReadData settings to DataExtensionAttribute New feature - Added reference and type name handling support to extension data New feature - Added default value and required support to constructor deserialization Change - Extension data is now written when serializing Fix - Added missing casts to JToken Fix - Fixed parsing large floating point numbers Fix - Fixed not parsing some ISO date ...Fast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Coevery - Free ASP.NET CRM: Coevery_WebApp: it just for publish to microsoft web app gellaryWsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.TerrariViewer: TerrariViewer v7 [Terraria Inventory Editor]: This is a complete overhaul but has the same core style. I hope you enjoy it. This version is compatible with 1.2.0.3 Please send issues to my Twitter or https://github.com/TJChap2840WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...Free language translator and file converter: Free Language Translator 3.4: fixe for new version look up.MoreTerra (Terraria World Viewer): MoreTerra 1.11.3: =========== =New Features= =========== New Markers added for Plantera's Bulb, Heart Fruits and Gold Cache. Markers now correctly display for the gems found in rock debris on the floor. =========== =Compatibility= =========== Fixed header changes found in Terraria 1.0.3.1Dynamics AX 2012 R2 Kitting: First Beta release of Kitting: First Beta release of Kitting Install by using XPO or Models.C# Intellisense for Notepad++: Release v1.0.8.0: - fixed document formatting artifacts To avoid the DLLs getting locked by OS use MSI file for the installation.CS-Script for Notepad++ (C# intellisense and code execution): Release v1.0.8.0: - fixed document formatting artifacts To avoid the DLLs getting locked by OS use MSI file for the installation.Generic Unit of Work and Repositories Framework: v2.0: Async methods for Repostiories - Ivan (@ifarkas) OData Async - Ivan (@ifarkas) Glimpse MVC4 workig with MVC5 Glimpse EF6 Northwind.Repostiory Project (layer) best practices for extending the Repositories Northwind.Services Project (layer), best practices for implementing business facade Live Demo: http://longle.azurewebsites.net/Spa/Product#/list Documentation: http://blog.longle.net/2013/10/09/upgrading-to-async-with-entity-framework-mvc-odata-asyncentitysetcontroller-kendo-ui-gli...Media Companion: Media Companion MC3.581b: Fix in place for TVDB xml issue. New* Movie - General Preferences, allow saving of ignored 'The' or 'A' to end of movie title, stored in sorttitle field. * Movie - New Way for Cropping Posters. Fixed* Movie - Rename of folders/filename. caught error message. * Movie - Fixed Bug in Save Cropped image, only saving in Pre-Frodo format if Both model selected. * Movie - Fixed Cropped image didn't take zoomed ratio into effect. * Movie - Separated Folder Renaming and File Renaming fuctions durin...(Party) DJ Player: DJP.124.12: 124.12 (Feature implementation completed): Changed datatype of HistoryDateInfo from string to DateTime New: HistoryDateInfoConverter for the listbox Improved: HistoryDateInfoDeleter, HistoryDateInfoLoader, HistoryDateInfoAsynchronizer, HistoryItemLoader, HistoryItemsToHistoryDateInfoConverterSmartStore.NET - Free ASP.NET MVC Ecommerce Shopping Cart Solution: SmartStore.NET 1.2.0: HighlightsMulti-store support "Trusted Shops" plugins Highly improved SmartStore.biz Importer plugin Add custom HTML content to pages Performance optimization New FeaturesMulti-store-support: now multiple stores can be managed within a single application instance (e.g. for building different catalogs, brands, landing pages etc.) Added 3 new Trusted Shops plugins: Seal, Buyer Protection, Store Reviews Added Display as HTML Widget to CMS Topics (store owner now can add arbitrary HT...NuGet: NuGet 2.7.1: Released October 07, 2013. Release notes: http://docs.nuget.org/docs/release-notes/nuget-2.7.1 Important note: After downloading the signed build of NuGet.exe, if you perform an update using the "nuget.exe update -self" command, it will revert back to the unsigned build.New Projectsaigiongai: aigiongaiArtificial LIfe BEing - ALIBE: An Autonomous Arduino Robot based on a 4 wheel electric RC style vehicle equipped w/ various sensors and reactionary devices powered by Arduino Mega. BH Auto-injector: This ia a BH hack injector developed for r/SlashDiablo. For more information visit: http://www.reddit.com/r/slashdiablo BloxServer: A server for a game currently in DevBugNet Premium: BugNet Premium is extended version of open source defect tracking tool BugNetCASP Editor: CASP Editor hosted at SimlogicalGrace: Grace is an Dependency Injection Container as well as a couple other services like Data Transformation Service, Validation Service, and Reflection Service.Halogy v1.2 CE1.0: Halogy v1.2 Community Edition v1.0Hot Likes: Simple web Application Like Facebook and TwitterHyper-V Backup.NET: TestIndexedList: This library helps you to create lists with large amount of data and do high speed searches on your data. Kinect Skeleton Stream to BVH Converter: The program converts the skeleton data stream into BVH.Mama Goose's Birthday & Anniversary Calendar: This is a simple calendar that allows entering birthdays and anniversaries and to print the calendar for the year or month.MQL to FDK converter with migration toolkit: "MQL to FDK" project provides an easy and convenient way for conversion of MQL advisers to C# and launching them on FDK.Produzr: Produzr is a very simple CMS without a high learning curve.PSWFWeb - PowerShell Workflow WebConsole: A PSWorkflow job managersacm: naSave Cleaner: Sims 3 save cleanerSimple AES file appender: Simple AES file appenderSims 3 Package Viewer: Sims 3 ProjectsxBot Framework: xBot Framework is a dot Net framework for building a bot for use with Reddit.com.

    Read the article

  • CodePlex Daily Summary for Thursday, October 17, 2013

    CodePlex Daily Summary for Thursday, October 17, 2013Popular ReleasesSocial Network Importer for NodeXL: SocialNetImporter(v.1.9): This new version includes: - Download latest status update and use it as vertex tooltip - Limit the timelines to parse to me, my friends or both - Fixed some reported bugs about the fan page and group importer - Fixed the login bug reported latelyDotNetNuke® Wiki: 05.00.00: Changes made to better support upgrades and the removal of deprecated legacy files that were causing formatting issues. Updated the Version number to better indicate the significance of the C# migration and the new DNN 7.0.2 minimum requirement.TerrariViewer: TerrariViewer v7.1 [Terraria Inventory Editor]: You can now backspace in number fields Items added in 1.2.0.3 no longer corrupt player files Buff durations capped at 9999999 Item stacks capped at 9999999 Version info added Prefix IDs corrected Shoe and Eye color box are now properly clickable Moved Bank and Safe into their own tab Users will now be notified of new updatesPython Tools for Visual Studio: 2.0: PTVS 2.0 We’re pleased to announce the release of Python Tools for Visual Studio 2.0 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, IPython, and cross platform and cross language debugging support. QUICK VIDEO OVERVIEW For a quick overview of the general IDE experience, please watch this v...C# Intellisense for Notepad++: Release v.1.0.8.2: Solved scrolling problem after DocumentFormatting Implemented "format as you type" --- To avoid the DLLs getting locked by OS use MSI file for the installation.CS-Script for Notepad++ (C# intellisense and code execution): Release v1.0.8.2: Solved scrolling problem after DocumentFormatting Implemented "format as you type" --- To avoid the DLLs getting locked by OS use MSI file for the installation.Collection Commander for Configuration Manager 2012: CMCollCtr 1.0.0: Change log: - MSI Setup - UI Improved - CM12 Console integration - New Powershell code snippets - Client Center IntegrationLINQ to Twitter: LINQ to Twitter v2.1.09: Supports .NET 3.5, .NET 4.0, .NET 4.5, Silverlight 4.0, Windows Phone 7.1, Windows Phone 8, Client Profile, Windows 8, and Windows Azure. 100% Twitter API coverage. Also supports Twitter API v1.1! Also on NuGet.Sandcastle Help File Builder: SHFB v1.9.8.0 with Visual Studio Package: General InformationIMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog. This new release contains bug fixes and feature enhancements. There are some potential breaking changes in this release as some features of the Help File Builder have been moved into...C++ REST SDK (codename "Casablanca"): C++ REST SDK 1.3.0: This release fixes multiple customer reported issues as well as the following: Full support for Dev12 binaries and project files Full support for Windows XP New sample highlighting the Client and Server APIs : BlackJack Expose underlying native handle to set custom options on http_client Improvements to Listener Library Note: Dev10 binaries have been dropped as of this release, however the Dev10 project files are still available in the Source CodeAD ACL Scanner: 1.3.2: Minor bug fixed: Powershell 4.0 will report: Select—Object: Parameter cannot be processed because the parameter name p is ambiguous.Json.NET: Json.NET 5.0 Release 7: New feature - Added support for Immutable Collections New feature - Added WriteData and ReadData settings to DataExtensionAttribute New feature - Added reference and type name handling support to extension data New feature - Added default value and required support to constructor deserialization Change - Extension data is now written when serializing Fix - Added missing casts to JToken Fix - Fixed parsing large floating point numbers Fix - Fixed not parsing some ISO date ...Fast YouTube Downloader: YouTube Downloader 2.2.0: YouTube Downloader 2.2.0VidCoder: 1.5.8 Beta: Added hardware acceleration options: Bicubic OpenCL scaling algorithm, QSV decoding/encoding and DXVA decoding. Updated HandBrake core to SVN 5834. Updated VidCoder setup icon. Fixed crash when choosing the mp4v2 container on x86 and opening on x64. Warning: the hardware acceleration features require specific hardware or file types to work correctly: QSV: Need an Intel processor that supports Quick Sync Video encoding, with a monitor hooked up to the Intel HD Graphics output and the lat...ASP.net MVC Awesome - jQuery Ajax Helpers: 3.5.2: version 3.5.2 - fix for setting single value to multivalue controls - datepicker min max date offset fix - html encoding for keys fix - enable Column.ClientFormatFunc to be a function call that will return a function version 3.5.1 - fixed html attributes rendering - fixed loading animation rendering - css improvements version 3.5 ========================== - autosize for all popups ( can be turned off by calling in js awe.autoSize = false ) - added Parent, Paremeter extensions ...Wsus Package Publisher: Release v1.3.1310.12: Allow the Update Creation Wizard to be set in full screen mode. Fix a bug which prevent WPP to Reset Remote Sus Client ID. Change the behavior of links in the Update Detail Viewer. Left-Click to open, Right-Click to copy to the Clipboard.WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.6.maint: I think this covers all of the issues. new additions: fixed the thumbnail problem for backgrounds. general clean up and error checking. need to get this put through the wringer and all feedback is welcome.BIDS Helper: BIDS Helper 1.6.4: This BIDS Helper release brings the following new features and fixes: New Features: A new Bus Matrix style report option when you run the Printer Friendly Dimension Usage report for an SSAS cube. The Biml engine is now fully in sync with the supported subset of Varigence Mist 3.4. This includes a large number of language enhancements, bugfixes, and project deployment support. Fixed Issues: Fixed Biml execution for project connections fixing a bug with Tabular Translations Editor not a...Free language translator and file converter: Free Language Translator 3.4: fixes for new version look up.PowerShell App Deployment Toolkit: PowerShell App Deployment Toolkit v3.0.6: Added PersistPrompt parameter to Show-InstallationWelcome and Show-InstallationPrompt. Prompt window is persistently returned to center screen after interval specified in config file (default 10 seconds). For Show-InstallationWelcome, this only takes effect if deferral is not available to user. The user will have no option but to respond to the prompt - resistance is futile! Added example advanced Office 2010 deployment script Asynchronous actions now write to the same log file as synchro...New ProjectsAdditionPage: This is a simple ASP.NET in VB.NET page that allows users to enter 2 numbers, and display their sum. Arad Enterprise Messaging Proxy: In these situations, the overhead and configuration complexity of an external webserver is seldom worth the trouble. AEMGP Server Implementation base on Socke.Boring Sudoku: Boring Sudoku is Sudoku game, made for SFML-game programming tutorial. Feel free to download the source code to learn more about game programming.Configurator Debug: O Configurator Debug é uma ferramenta que auxilia na depuração das queries da feature do Configurador no Dynamics AX 2009.Fast Query: FastQuery - is a tool to execute MS SQL Queries without SQL Server Management Studio (SSMS). gdrwebapp1: Test ProjectK2 workflow Manifestation d'interet with custom IPF methode: K2 SamplesL Language Interpreter: We are now in dev start stage, when none of the functionality is available, but probably you will be able to see it published. this shoud have tex outputLameXP - Audio Encoder Front-End: LameXP is a graphical user-interface for various of audio encoders: It allows you convert audio files from one format to another one in the most simple way.Learn Node.js: Node.js express jade ...localcompare: localhistory add new featureOpen source WPF PDF Viewer: Open source PDF Viewer based on Apitron PDF Rasterizer for .NET component that performs high-quality conversion from PDF file to an image.Pfz.AnimationManagement: A .NET animation library that supports both declarative and imperative animations, capable of creating from simple animation to entire games.SerieSpotter: .net projectSimpleUnitity: ??????? ??? DataBase, TextLog, CacheSPOnlineDevelopTool(SharePoint ??????): SPOnlineDevelopTool?????????SharePoint WebPart?SharePoint WebPartVoya Media: Voya Media is free, open-source and provides one central place to play and organize all your music, pictures and videos.

    Read the article

  • Synergy - easy share of keyboard and mouse between multiple computers

    Did you ever have the urge to share one set of keyboard and mouse between multiple machines? If so, please read on... Using multiple machines Honestly, as a software craftsman it is my daily business to run multiple machines - either physical or virtual - to be able to solve my customers' requirements. Recent hardware equipment allows this very easily. For laptops it's a no-brainer to attach a second or even a third screen in order to extend your native display. This works quite handy and in my case I used to attached two additional screens - one via HD15 connector, the other via HDMI. But... as it's a laptop and therefore a mobile unit there are slight restrictions. Detaching and re-attaching all cables when changing locations is one of them but hardware limitations, too. After all, it's a laptop and not a workstation. I guess, that anyone working in IT (or ICT) has more than one machine at their workplace or their home office and at least I find it quite annoying to have multiple sets of keyboard and mouse conquering my remaining space on my desk. Despite the ugly looks of all those cables and whatsoever 'chaos of distraction' I prefer a more clean solution and working environment. This allows me to actually focus on my work and tasks to do rather than to worry about choosing the right combination of keyboard/mouse. My current workplace is a patch work of various pieces of hardware (approx. 2-3 years): DIY desktop on Ubuntu 12.04 64-bit, Core2 Duo (E7400, 2.8GHz), 4GB RAM, 2x 250GB HDD, nVidia GPU 512MB Dell Inspiron 1525 on Windows 8 64-bit, 4GB RAM, 200GB HDD HP Compaq 6720s on Windows Vista 32-bit, Core2 Duo (T5670, 1.8GHz), 2GB RAM, 160GB HDD Mac mini on Mac OS X 10.7, Core i5 (2.3 GHz), 2GB RAM, 500GB HDD I know... Not the latest and greatest but a decent combination to work with. New system(s) is/are already on the shopping list but I live in the 'wrong' country to buy computer hardware. So, the next trip abroad will provide me with some new stuff. Using multiple operating systems The list of hardware above already names different operating systems, and actually I have only one preference: Linux. But still my job as a software craftsman for Visual FoxPro and .NET development requires other OSes, too. Not a big deal, it's just like this. Additionally to those physical machines, there are a bunch of virtual machines around. Most of them running either Windows XP or Windows 7. Since years I have the practice that each development for one customer is isolated into its own virtual machine and environment. This keeps it clean and version-safe. But as you can easily imagine with that setup there are a couple of constraints referring to keyboard and mouse. Usually, those systems require their own pieces of hardware attached. As stated, I don't like clutter on my desk's surface, so a cross-platform solution has to come in here. In the past, I tried it with various applications, hardware or network protocols like X11, RDP, NX, TeamViewer, RAdmin, KVM switch, etc. but the problem in this case is that they either allow you to remotely connect to the other system or exclusively 'bind' your peripherals to the active system. Not optimal after all. Synergy to the rescue Quote from their website: "Synergy lets you easily share your mouse and keyboard between multiple computers on your desk, and it's Free and Open Source. Just move your mouse off the edge of one computer's screen on to another. You can even share all of your clipboards. All you need is a network connection. Synergy is cross-platform (works on Windows, Mac OS X and Linux)." Yep, that's it! All I need for my setup here... Actually, I couldn't believe it myself that I didn't stumble over synergy earlier but 'Get over it' and there we go. And despite the fact that it is Open Source, no, it's also for free. Donations for the developers are very welcome and recently they introduced Synergy Premium. A possibility to buy so-called premium votes that can be used to put more weight / importance on specific issues or bugs that you would like the developers to look into. Installation and configuration Simply download the installation packages for your systems of choice, run the installer and enter some minor information about your network setup. I chose my desktop machine for the role of the Synergy server and configured my screen setup as follows: The screen setup allows you currently to build or connect up to 15 machines. The number of screens can be higher as those machine might have multiple screens physically attached. Synergy takes this into the overall calculations and simply works as expected. I tried it for fun with a second monitor each connected to both laptops to have a total number of 6 active screens. No flaws after all - stunning! All the other machines are configured as clients like so: Side note: The screenshot was taken on Windows 8 and pasted via clipboard into Gimp running on Ubuntu. Resume Synergy is now definitely in my box of tools for my daily work, and amongst the first pieces of software I install after the operating system. It just simplifies my life and cleans my desk. Never again without Synergy!Now, only waiting for an Android version to integrate my Galaxy Tab 10.1, too. ;-) Please, check out that superb product and enjoy sharing one keyboard, one mouse and one clipboard between your various machines and operating systems.

    Read the article

  • How to set BackGround color to a divider in JSplitPane

    - by Sunil Kumar Sahoo
    I have created a divider in JSplitPane. I am unable to set the color of divider. I want to set the color of divider. please help me how to set color of that divider import javax.swing.; import java.awt.; import java.awt.event.*; public class SplitPaneDemo { JFrame frame; JPanel left, right; JSplitPane pane; int lastDividerLocation = -1; public static void main(String[] args) { SplitPaneDemo demo = new SplitPaneDemo(); demo.makeFrame(); demo.frame.addWindowListener(new WindowAdapter() { public void windowClosing(WindowEvent e) { System.exit(0); } }); demo.frame.show(); } public JFrame makeFrame() { frame = new JFrame(); // Create a horizontal split pane. pane = new JSplitPane(JSplitPane.HORIZONTAL_SPLIT); left = new JPanel(); left.setBackground(Color.red); pane.setLeftComponent(left); right = new JPanel(); right.setBackground(Color.green); pane.setRightComponent(right); JButton showleft = new JButton("Left"); showleft.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { Container c = frame.getContentPane(); if (pane.isShowing()) { lastDividerLocation = pane.getDividerLocation(); } c.remove(pane); c.remove(left); c.remove(right); c.add(left, BorderLayout.CENTER); c.validate(); c.repaint(); } }); JButton showright = new JButton("Right"); showright.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { Container c = frame.getContentPane(); if (pane.isShowing()) { lastDividerLocation = pane.getDividerLocation(); } c.remove(pane); c.remove(left); c.remove(right); c.add(right, BorderLayout.CENTER); c.validate(); c.repaint(); } }); JButton showboth = new JButton("Both"); showboth.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { Container c = frame.getContentPane(); c.remove(pane); c.remove(left); c.remove(right); pane.setLeftComponent(left); pane.setRightComponent(right); c.add(pane, BorderLayout.CENTER); if (lastDividerLocation >= 0) { pane.setDividerLocation(lastDividerLocation); } c.validate(); c.repaint(); } }); JPanel buttons = new JPanel(); buttons.setLayout(new GridBagLayout()); buttons.add(showleft); buttons.add(showright); buttons.add(showboth); frame.getContentPane().add(buttons, BorderLayout.NORTH); pane.setPreferredSize(new Dimension(400, 300)); frame.getContentPane().add(pane, BorderLayout.CENTER); frame.pack(); pane.setDividerLocation(0.5); return frame; } } Thanks Sunil kumar Sahoo

    Read the article

  • Incremental PCA

    - by smichak
    Hi, Lately, I've been looking into an implementation of an incremental PCA algorithm in python - I couldn't find something that would meet my needs so I did some reading and implemented an algorithm I found in some paper. Here is the module's code - the relevant paper on which it is based is mentioned in the module's documentation. I would appreciate any feedback from people who are interested in this. Micha #!/usr/bin/env python """ Incremental PCA calculation module. Based on P.Hall, D. Marshall and R. Martin "Incremental Eigenalysis for Classification" which appeared in British Machine Vision Conference, volume 1, pages 286-295, September 1998. Principal components are updated sequentially as new observations are introduced. Each new observation (x) is projected on the eigenspace spanned by the current principal components (U) and the residual vector (r = x - U(U.T*x)) is used as a new principal component (U' = [U r]). The new principal components are then rotated by a rotation matrix (R) whose columns are the eigenvectors of the transformed covariance matrix (D=U'.T*C*U) to yield p + 1 principal components. From those, only the first p are selected. """ __author__ = "Micha Kalfon" import numpy as np _ZERO_THRESHOLD = 1e-9 # Everything below this is zero class IPCA(object): """Incremental PCA calculation object. General Parameters: m - Number of variables per observation n - Number of observations p - Dimension to which the data should be reduced """ def __init__(self, m, p): """Creates an incremental PCA object for m-dimensional observations in order to reduce them to a p-dimensional subspace. @param m: Number of variables per observation. @param p: Number of principle components. @return: An IPCA object. """ self._m = float(m) self._n = 0.0 self._p = float(p) self._mean = np.matrix(np.zeros((m , 1), dtype=np.float64)) self._covariance = np.matrix(np.zeros((m, m), dtype=np.float64)) self._eigenvectors = np.matrix(np.zeros((m, p), dtype=np.float64)) self._eigenvalues = np.matrix(np.zeros((1, p), dtype=np.float64)) def update(self, x): """Updates with a new observation vector x. @param x: Next observation as a column vector (m x 1). """ m = self._m n = self._n p = self._p mean = self._mean C = self._covariance U = self._eigenvectors E = self._eigenvalues if type(x) is not np.matrix or x.shape != (m, 1): raise TypeError('Input is not a matrix (%d, 1)' % int(m)) # Update covariance matrix and mean vector and centralize input around # new mean oldmean = mean mean = (n*mean + x) / (n + 1.0) C = (n*C + x*x.T + n*oldmean*oldmean.T - (n+1)*mean*mean.T) / (n + 1.0) x -= mean # Project new input on current p-dimensional subspace and calculate # the normalized residual vector g = U.T*x r = x - (U*g) r = (r / np.linalg.norm(r)) if not _is_zero(r) else np.zeros_like(r) # Extend the transformation matrix with the residual vector and find # the rotation matrix by solving the eigenproblem DR=RE U = np.concatenate((U, r), 1) D = U.T*C*U (E, R) = np.linalg.eigh(D) # Sort eigenvalues and eigenvectors from largest to smallest to get the # rotation matrix R sorter = list(reversed(E.argsort(0))) E = E[sorter] R = R[:,sorter] # Apply the rotation matrix U = U*R # Select only p largest eigenvectors and values and update state self._n += 1.0 self._mean = mean self._covariance = C self._eigenvectors = U[:, 0:p] self._eigenvalues = E[0:p] @property def components(self): """Returns a matrix with the current principal components as columns. """ return self._eigenvectors @property def variances(self): """Returns a list with the appropriate variance along each principal component. """ return self._eigenvalues def _is_zero(x): """Return a boolean indicating whether the given vector is a zero vector up to a threshold. """ return np.fabs(x).min() < _ZERO_THRESHOLD if __name__ == '__main__': import sys def pca_svd(X): X = X - X.mean(0).repeat(X.shape[0], 0) [_, _, V] = np.linalg.svd(X) return V N = 1000 obs = np.matrix([np.random.normal(size=10) for _ in xrange(N)]) V = pca_svd(obs) print V[0:2] pca = IPCA(obs.shape[1], 2) for i in xrange(obs.shape[0]): x = obs[i,:].transpose() pca.update(x) U = pca.components print U

    Read the article

  • Representing game states in Tic Tac Toe

    - by dacman
    The goal of the assignment that I'm currently working on for my Data Structures class is to create a of Quantum Tic Tac Toe with an AI that plays to win. Currently, I'm having a bit of trouble finding the most efficient way to represent states. Overview of current Structure: AbstractGame Has and manages AbstractPlayers (game.nextPlayer() returns next player by int ID) Has and intializes AbstractBoard at the beginning of the game Has a GameTree (Complete if called in initialization, incomplete otherwise) AbstractBoard Has a State, a Dimension, and a Parent Game Is a mediator between Player and State, (Translates States from collections of rows to a Point representation Is a StateConsumer AbstractPlayer Is a State Producer Has a ConcreteEvaluationStrategy to evaluate the current board StateTransveralPool Precomputes possible transversals of "3-states". Stores them in a HashMap, where the Set contains nextStates for a given "3-state" State Contains 3 Sets -- a Set of X-Moves, O-Moves, and the Board Each Integer in the set is a Row. These Integer values can be used to get the next row-state from the StateTransversalPool SO, the principle is Each row can be represented by the binary numbers 000-111, where 0 implies an open space and 1 implies a closed space. So, for an incomplete TTT board: From the Set<Integer> board perspective: X_X R1 might be: 101 OO_ R2 might be: 110 X_X R3 might be: 101, where 1 is an open space, and 0 is a closed space From the Set<Integer> xMoves perspective: X_X R1 might be: 101 OO_ R2 might be: 000 X_X R3 might be: 101, where 1 is an X and 0 is not From the Set<Integer> oMoves perspective: X_X R1 might be: 000 OO_ R2 might be: 110 X_X R3 might be: 000, where 1 is an O and 0 is not Then we see that x{R1,R2,R3} & o{R1,R2,R3} = board{R1,R2,R3} The problem is quickly generating next states for the GameTree. If I have player Max (x) with board{R1,R2,R3}, then getting the next row-states for R1, R2, and R3 is simple.. Set<Integer> R1nextStates = StateTransversalPool.get(R1); The problem is that I have to combine each one of those states with R1 and R2. Is there a better data structure besides Set that I could use? Is there a more efficient approach in general? I've also found Point<-State mediation cumbersome. Is there another approach that I could try there? Thanks! Here is the code for my ConcretePlayer class. It might help explain how players produce new states via moves, using the StateProducer (which might need to become StateFactory or StateBuilder). public class ConcretePlayerGeneric extends AbstractPlayer { @Override public BinaryState makeMove() { // Given a move and the current state, produce a new state Point playerMove = super.strategy.evaluate(this); BinaryState currentState = super.getInGame().getBoard().getState(); return StateProducer.getState(this, playerMove, currentState); } } EDIT: I'm starting with normal TTT and moving to Quantum TTT. Given the framework, it should be as simple as creating several new Concrete classes and tweaking some things.

    Read the article

  • What's the most unsound program you've had to maintain?

    - by Robert Rossney
    I periodically am called upon to do maintenance work on a system that was built by a real rocket surgeon. There's so much wrong with it that it's hard to know where to start. No, wait, I'll start at the beginning: in the early days of the project, the designer was told that the system would need to scale, and he'd read that a source of scalability problems was traffic between the application and database servers, so he made sure to minimize this traffic. How? By putting all of the application logic in SQL Server stored procedures. Seriously. The great bulk of the application functions by the HTML front end formulating XML messages. When the middle tier receives an XML message, it uses the document element's tag name as the name of the stored procedure it should call, and calls the SP, passing it the entire XML message as a parameter. It takes the XML message that the SP returns and returns it directly back to the front end. There is no other logic in the application tier. (There was some code in the middle tier to validate the incoming XML messages against a library of schemas. But I removed it, after ascertaining that 1) only a small handful of messages had corresponding schemas, 2) the messages didn't actually conform to these schemas, and 3) after validating the messages, if any errors were encountered, the method discarded them. "This fuse box is a real time-saver - it comes from the factory with pennies pre-installed!") I've seen software that does the wrong thing before. Lots of it. I've written quite a bit. But I've never seen anything like the steely-eyed determination to do the wrong thing, at every possible turn, that's embodied in the design and programming of this system. Well, at least he went with what he knew, right? Um. Apparently, what he knew was Access. And he didn't really understand Access. Or databases. Here's a common pattern in this code: SELECT @TestCodeID FROM TestCode WHERE TestCode = @TestCode SELECT @CountryID FROM Country WHERE CountryAbbr = @CountryAbbr SELECT Invoice.*, TestCode.*, Country.* FROM Invoice JOIN TestCode ON Invoice.TestCodeID = TestCode.ID JOIN Country ON Invoice.CountryID = Country.ID WHERE Invoice.TestCodeID = @TestCodeID AND Invoice.CountryID = @CountryID Okay, fine. You don't trust the query optimizer either. But how about this? (Originally, I was going to post this in What's the best comment in source code you have ever encountered? but I realized that there was so much more to write about than just this one comment, and things just got out of hand.) At the end of many of the utility stored procedures, you'll see code that looks like the following: -- Fix NULLs SET @TargetValue = ISNULL(@TargetValue, -9999) Yes, that code is doing exactly what you can't allow yourself to believe it's doing lest you be driven mad. If the variable contains a NULL, he's alerting the caller by changing its value to -9999. Here's how this number is commonly used: -- Get target value EXEC ap_GetTargetValue @Param1, @Param2, OUTPUT @TargetValue -- Check target value for NULL value IF @TargetValue = -9999 ... Really. For another dimension of this system, see the article on thedailywtf.com entitled I Think I'll Call Them "Transactions". I'm not making any of this up. I swear. I'm often reminded, when I work on this system, of Wolfgang Pauli's famous response to a student: "That isn't right. It isn't even wrong." This can't really be the very worst program ever. It's definitely the worst one I've worked

    Read the article

  • zoom a JPanel and all of its components

    - by user253530
    I have a big JPanel which holds many TileMapping objects (TileMapping extends JPanel). I want to zoom the big JPanel and all of its components to be scaled aswell. A TileMapping has an image which of course has to be zoomed as well. here is my TileMapping class public class TileMapping extends JPanel { private double zoom = 1.0; private Mapping mapping; private int height; private int width; private int xCoord; private int yCoord; TileMapping(Mapping m, int w, int h, int x, int y) { super(); mapping = m; height = h; width = w; this.xCoord = x; this.yCoord = y; this.setPreferredSize(new Dimension(w, h)); } public int getXcoord() { return xCoord; } public int getYcoord() { return yCoord; } public Mapping getMapping() { return mapping; } public void setMapping(Mapping m) { mapping = m; } public void originalSize() { zoom = 1; } public void zoomIn() { zoom += 0.2; } public void zoomOut() { zoom -= 0.2; } @Override public void paintComponent(Graphics g) { Graphics2D g2d = (Graphics2D) g; if (mapping.getImage() != null) { BufferedImage bg = mapping.getImage(); g2d.scale(zoom, zoom); g2d.drawImage(bg, 0, 0, width, height, this); } else { g2d.scale(zoom, zoom); this.setBackground(Color.white); } } } I need to know how i should continue this on the main JPanel which is populated using this code: This is part of a MapWindow class. if you carefully read the code you will understand what i'm talking about. Basically this is a Tile MapEditor and I am simulating a Tile as a JPanel which holds the mapping object (mapping is a binding between an ASCII character and an image) you place. private void populateMapPanel(Map map) { GridBagConstraints c = new GridBagConstraints(); mapPanel.setLayout(new GridBagLayout()); for (int i = 0; i < map.getMapGrid().getRows(); i++) { for (int j = 0; j < map.getMapGrid().getColumns(); j++) { tile = new TileMapping(map.getMapItem(i, j), cellSize, cellSize, i, j); tile.setBorder(new LineBorder(Color.black)); tile.addMouseListener(this); tile.addMouseMotionListener(this); c.gridx = i; c.gridy = j; mapPanel.add(tile, c); } } mapPanel.validate(); mapPanel.repaint(); } I need to know how to do the following: 1. When the user presses Zoom In the mapPanel should zoom in and also all the images in the smaller panels. 2. when the user click and drag over the TileMappings an image should be painted on them and this image should get scaled of course if the mapPanel is zoomed. Pseudo code, ideas, hints, java code ...anything would be helpful. Thank you

    Read the article

  • How do I get a JPanel with an empty JLabel to take up space in a GridBagLayout

    - by user2888663
    I am working on a GUI for a project at school. I am using a GridBagLayout in swing. I want to have a label indicating the input(a type of file @ x = 0, y = 0), followed by another label(the actual file name once selected @ x = 1, y = 0), followed by a browse button for a file chooser( @ x = 2, y = 0). The label at (1,0) is initially blank, however I want the area that the text will occupy to take up some space when the label contains no text. I also want the space between the label at (0,0) and the button at (2,0) to remain constant. To achieve this, I'm trying to put the label onto a panel and then play with the layouts. However I can't seam to achieve the desired results. Could anyone offer some suggestions? The next three rows of the GridBagLayout will be laid out exactly the same way. Here is a link to a screen shot of the GUI. calibrationFileSelectionValueLabel = new JLabel("",Label.LEFT); calibrationFileSelectionValueLabel.setName("calibrationFileSelection"); calibrationFileSelectionValueLabel.setMinimumSize(new Dimension(100,0)); calibrationFileSelectionValuePanel = new JPanel(); calibrationFileSelectionValuePanel.setBorder(BorderFactory.createEtchedBorder()); calibrationFileSelectionValuePanel.add(calibrationFileSelectionValueLabel); c.gridx = 0; c.gridy = 0; c.fill = GridBagConstraints.NONE; filesPanel.add(calibrationFileLabel,c); c.gridy = 1; filesPanel.add(frequencyFileLabel,c); c.gridy = 2; filesPanel.add(sampleFileLabel,c); c.gridy = 3; filesPanel.add(outputFileLabel,c); c.gridx = 1; c.gridy = 0; c.fill = GridBagConstraints.BOTH; // filesPanel.add(calibrationFileSelection,c); filesPanel.add(calibrationFileSelectionValuePanel,c); c.gridy = 1; // filesPanel.add(frequencyFileSelection,c); filesPanel.add(frequencyFileSelectionValueLabel,c); c.gridy = 2; // filesPanel.add(sampleFileSelection,c); filesPanel.add(sampleFileSelectionValueLabel,c); c.gridy = 3; // filesPanel.add(outputFileSelection,c); filesPanel.add(outputFileSelectionValueLabel,c); c.gridx = 2; c.gridy = 0; c.fill = GridBagConstraints.NONE; filesPanel.add(calibrationFileSelectionButton,c); c.gridy = 1; filesPanel.add(frequencyFileSelectionButton,c); c.gridy = 2; filesPanel.add(sampleFileSelectionButton,c); c.gridy = 3; filesPanel.add(createOutputFileButton,c); panelForFilesPanelBorder = new JPanel(); panelForFilesPanelBorder.setBorder(BorderFactory.createCompoundBorder(new EmptyBorder(5,10,5,10), BorderFactory.createEtchedBorder())); panelForFilesPanelBorder.add(filesPanel); buttonsPanel = new JPanel(); buttonsPanel.setLayout(new FlowLayout(FlowLayout.CENTER)); buttonsPanel.setBorder(BorderFactory.createCompoundBorder(new EmptyBorder(5,10,10,10), BorderFactory.createEtchedBorder())); buttonsPanel.add(startButton); buttonsPanel.add(stopButton); basePanel.add(panelForFilesPanelBorder); basePanel.add(numericInputPanel); basePanel.add(buttonsPanel);

    Read the article

  • get eigenvalue pca with java

    - by Muhamad Burhanudin
    I try use PCA to reduce dimention, and i use jama for help me using matrix. but, i got problem when get eigenvalue with jama. for example i hava 2 image dimention 100x100, then i create single matrix 2 image x (100x100). there is 20.000 pixel. and how to get reduction with eigenvalue? this is sample my code : public static void main(String[] args) { BufferedImage bi; int[] rgb; int R, G, B; // int[] jum; double[][] gray = new double[500][500] ; String[] baris = new String[1000]; try { //bi = ImageIO.read(new File("D:\\c.jpg")); int[][] pixelData = new int[bi.getHeight() * bi.getWidth()][3]; int counter = 0; for (int i = 0; i < bi.getHeight(); i++) { for (int j = 0; j < bi.getWidth(); j++) { gray[i][j] = getPixelData(bi, i, j); // R = getR(bi, i, j); //G = getG(bi, i, j); //B = getB(bi, i, j); //jum = R + G + B; // gray[counter] = Double.toString(R + G + B / 3); // System.out.println("Gray " +gray); //for (int k = 0; k < rgb.length; k++) { // pixelData[counter][k] = rgb[k]; // } counter++; } } } catch (IOException e) { e.printStackTrace(); } Matrix matrix = new Matrix(gray); PCA pca = new PCA(matrix); pca.getEigenvalue(6); String n = pca.toString(); System.err.println("nilai n "+n); //double dete = pcadete(matrix,3600); } private static int getPixelData(BufferedImage bi, int x, int y) { int argb = bi.getRGB(y, x); int r, g, b; int gray; int rgb[] = new int[]{ (argb >> 16) & 0xff, //red (argb >> 8) & 0xff, //green (argb) & 0xff //blue }; r = rgb[0]; g = rgb[1]; b = rgb[2]; gray = (r + g + b) / 3; System.out.println("gray: " + gray); return gray; } when i show eigenvalue in this code : PCA pca = new PCA(matrix); pca.getEigenvalue(6); String n = pca.toString(); System.err.println("nilai n "+n); Result is : nilai n PCA@c3e9e9 Can, u tell me what way to get eigenvalue and reduction dimension.

    Read the article

  • Recursing data into a 2 dimensional array in PHP 5

    - by user315699
    I'm getting bamboozled by "for each" loops and two dimensional arrays, and I'm a php newb so please bear with me (and ignore any variables with the word "image" - it's all about the mp3s, I just didn't change it from the xml tutorial) I found a php function on the net that list files in a directory, the output of which is: Array ( [0] = audio/1.mp3 [1] = audio/2.mp3 [2] = audio/3.mp3 [3] = audio/4.mp3 [4] = audio/5.mp3 ) As expected. And another that lists some info about mp3 files. $mp3datafile = 'audio/1.mp3'; $m = new mp3file($mp3datafile); $mp3dataArray = $m-get_metadata(); print_r($mp3dataArray); unset($mp3dataArray); The output of which is Array ( [Filesize] = 31972 [Encoding] = CBR [etc] ) In order to automatically build RSS for a podcast, I need to generate XML for each item. So far so good. This is how I'm making the xml foreach ($imagearray as $key = $val) { $tnsoundfile = $xml_generator-addChild('item'); $tnsoundfile-addChild('title', $podcasttitle); $enclosure = $tnsoundfile-addChild('enclosure'); $enclosure-addAttribute('url', $val); // that's the filename $enclosure-addAttribute('length', $mp3dataArray[Filesize]); // << Length is file length, not time. But later I also need $mp3dataArray[Length mm:ss] for duration tag. $enclosure-addAttribute('type', 'audio/mpeg'); $tnsoundfile-addChild('guid', $path_to_image_dir.'/'.$val); } (The above has been truncated, I realise it's not proper xml right now, but it was just to show what was going on). Perfect. But I need to do it for as many files as there are in the directory. So, I have an array of the names of the files in the directory in $mp3data And, I have an array of mp3 data in $mp3dataArray from one iteration of the get_metadata() function. If I do the following, then I get a nice list of the mp3 data of the 5 files in the directory: foreach ($mp3data as $key = $val) { $mp3datafile = $val; $m = new mp3file($mp3datafile); $mp3dataArray = $m-get_metadata(); print_r($mp3dataArray); unset($mp3dataArray); } As expected. Where I'm struggling, and have been for most of the day in spite of reading many forums and tutorials, is how to populate the "second dimension" of the array, so that it goes through 1,2,3,4 and 5.mp3 (or however many there are), extracts the metadata, then allows me to use it in the xml section above. Here's what I have foreach ($mp3data as $key = $val) { $mp3datafile = $val; $m = new mp3file($mp3datafile); $mp3dataArray = $m-get_metadata(); $mp3testarray = array($mp3dataArray); } print_r($mp3dataArray); Shouldn't that line print_r($mp3dataArray); give me a nice list of 5 lots of mp3 data, in the way it did when I recursed through the loop as before? Cos this is driving me nuts! It must be something so simple, and any help would be greatly appreciated. Thank you in advance.

    Read the article

  • Accessing a vector<vector<int>> as a flat array

    - by user1762276
    For this array: vector<vector<int> > v; v.push_back(vector<int>(0)); v.back().push_back(1); v.back().push_back(2); v.back().push_back(3); v.back().push_back(4); I can output {1, 2, 3, 4} easily enough: cout << v[0][0] << endl; cout << v[0][1] << endl; cout << v[0][2] << endl; cout << v[0][3] << endl; To access it as a flat array I can do this: int* z = (int*)&v[0].front(); cout << z[0] << endl; cout << z[1] << endl; cout << z[2] << endl; cout << z[3] << endl; Now, how do I access the multidimensional vector as a flat multidimensional array? I cannot use the same format as accessing a single-dimensional vector: // This does not work (outputs garbage) int** n = (int**)&v.front(); cout << n[0][0] << endl; cout << n[0][1] << endl; cout << n[0][2] << endl; cout << n[0][3] << endl; The workaround I've found is to do this: int** n = new int* [v.size()]; for (size_t i = 0; i < v.size(); i++) { n[i] = &v.at(i).front(); } cout << n[0][0] << endl; cout << n[0][1] << endl; cout << n[0][2] << endl; cout << n[0][3] << endl; Is there a way to access the entire multidimensional vector like a flat c-style array without having to dynamically allocate each dimension above the data before accessing it? Speed is not critical in the implementation and clarity for maintenance is paramount. A multidimensional vector is just fine for storing the data. However, I want to also expose the data as a flat c-style array in the SDK so that it can be easily accessible by other languages. This means that exposing the vectors as an STL object is a no go. The solution I came up with works fine for my needs as I only evaluate the array once at the very end of processing to "flatten" it. However, is there a better way to go about this? Or am I already doing it the best way I possibly can without re-implementing my own data structure (overkill since my flatten code is only a few lines). Thank you for your advice, friends!

    Read the article

  • My Jtable is blank

    - by mazin
    Hello my q is about a jtable that i have ,i fill it with components from a .txt ,I have a main (menu ) JFrame and by pressing a jbutton i want the jtable to pop out ! My problem is that my jtable is blank and it supposed to show some date !I would appreciated any help , Thanks. this is my ''reading'' class` public static void main(String[] args) { company Company=new company(); payFrame jframe=new payFrame(Company); jframe.setDefaultCloseOperation( JFrame.EXIT_ON_CLOSE); jframe.setSize(600,300); jframe.setVisible(true); readClass(); } //diavasma public static void readClass(){ ArrayList<Employee> emp =new ArrayList<Employee>() ; //Employee[] emp=new Employee[7]; //read from file try { int i=0; // int rowCounter; // int payments=0; String inputDocument = ("src/Employees.txt"); FileInputStream is = new FileInputStream(inputDocument); Reader iD = new InputStreamReader(is); BufferedReader buf = new BufferedReader(iD); String inputLine; while ((inputLine = buf.readLine()) != null) { String[] lineParts = inputLine.split(","); String email = (lineParts[7]); int EmpNo = Integer.parseInt(lineParts[0]); String type = lineParts[10]; int PostalCode = Integer.parseInt(lineParts[5]); int phone = Integer.parseInt(lineParts[6]); int DeptNo = (short) Integer.parseInt(lineParts[8]); double Salary; int card = (short) Integer.parseInt(lineParts[10]); int emptype = 0; int hours=Integer.parseInt(lineParts[11]); if (type.equals("FULL TIME")) { emptype = 1; } else if (type.equals("SELLER")) { emptype = 2; } else { emptype = 3; } /** * Creates employee instances depending on their type of employment * (fulltime=1, salesman=2, parttime=3) */ switch (emptype) { case 1: Salary = Double.parseDouble(lineParts[10]); emp.add(new FullTime(lineParts[1], lineParts[2], EmpNo, lineParts[3], lineParts[4], PostalCode, phone, email, DeptNo, card, Salary,hours, type)); i++; break; and this is my class where i make my Jtable and fill him public class company extends JFrame { private ArrayList<Employee> emp = new ArrayList<Employee>(); public void addEmployee(Employee emplo) { emp.add(emplo); } public ArrayList<Employee> getArray() { return emp; } public void getOption1() { ArrayList<Employee> employee = getArray(); JTable table = new JTable(); DefaultTableModel model = new DefaultTableModel(); table.setModel(model); model.setColumnIdentifiers(new String[]{"Code", "First Name", "Last Name", "Address", "City", "Postal Code", "Phone", "Email", "Dept Code", "Salary", "Time Card", "Hours"}); for (Employee current : employee) { model.addRow(new Object[]{current.getempCode(), current.getfirst(), current.getlast(), current.getaddress(), current.getcity(), current.getpostalCode(), current.gettelephone(), current.getemail(), current.getdep(), current.getsalary(), current.getcardcode(), current.getHours() }); } table.setPreferredScrollableViewportSize(new Dimension(500, 50)); table.setFillsViewportHeight(true); JScrollPane scrollPane = new JScrollPane(table); add(scrollPane); setVisible(true); table.revalidate();

    Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131  | Next Page >