Search Results

Search found 7024 results on 281 pages for 'usb modem'.

Page 127/281 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• Why wireless adatper stop to work?

  - by AndreaNobili

  today I correctly installed the driver for the TP-LINK TL-WN725N USB wireless adapter on my RaspBerry Pi (I use RaspBian that is a Debian), then I setted up the wifi using the wpa-supplicant as explained in this tutorial: http://www.maketecheasier.com/setup-wifi-on-raspberry-pi/ This worked fine untill this evening. Then suddenly it stopped to work when I try to connect in SSH and the Raspberry is on the wireless (or rather it should be, as this is not in the list of my router's DHCP connected Client) The strange thing is that the USB wirless adapter blink so I think that this is not a driver problem. If I try to connect it by the ethernet I have no problem. It appear in my router's DHCP connected Client and I can connect to it by SSH. When I connect to it using ethernet if I perform an ifconfig command I obtain: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.9 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:59 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6006 (5.8 KiB) TX bytes:8268 (8.0 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1104 (1.0 KiB) TX bytes:1104 (1.0 KiB) wlan0 Link encap:Ethernet HWaddr e8:94:f6:19:80:4c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So it seems that the wlan0 USB wireless adapter driver is correctly loaded. If I remove the USB wireless adapter and put it again into the USB port, the lasts lines of dmesg log is: [ 20.303172] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 20.306340] RTL871X: set bssid:00:00:00:00:00:00 [ 20.306726] RTL871X: set ssid [g\xffffffc6isQ\xffffffffJ\xffffffec)\xffffffcd\xffffffba\xffffffba\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8\x1b\xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9f\xffffffc9\xffffff9a\xffffff9aD\xffffffa7\x1a\xffffffa0\x1a\xffffff8b] fw_state=0x00000008 [ 21.614585] RTL871X: indicate disassoc [ 21.908495] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 25.006282] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS [ 26.247997] RTL871X: nolinked power save enter As you can see some of these line are related to the RTL871X that is my USB wireless adapter, but I don't know is that these line report an error or if it is all ok. Looking at the adapter status I obtain: pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff As you can see the mode is DORMANT but I think that this is normal because now I am connected using ethernet. I tryied to set up the adapter but it seems that I obtain no result, infact: pi@raspberrypi ~ $ sudo ip link set dev wlan0 up pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff pi@raspberrypi ~ $ sudo ip link set dev wlan0 up This is my /etc/network/interfaces file content and it is ok: auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp and it is the /etc/wpa_supplicant/wpa_supplicant.conf that I think is ok (I did not change it compared to when it worked): ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 network={ ssid="MY-NETWORK" psk="mypassword" key_mgmt=WPA-PSK } and infact if I execute a network scan I correctly find MY-NETWORK in the network list,infact: pi@raspberrypi ~ $ sudo iwlist wlan0 scan | grep ESSID ESSID:"TeleTu_74888B0060AD" ESSID:"MY-NETWORK" ESSID:"FASTWEB-1-PT6NtjL4TOSe" ESSID:"DC" So I reboot the system and I remove the ethernet cable but when I try to connect again to my raspberry I obatin the following error message: andrea@andrea-virtual-machine:~$ sudo ssh [email protected] ssh: connect to host 192.168.1.9 port 22: No route to host It seems that it can't connect using wireless. What could be the problem? What am I missing? How can I solve this situation? Tnx

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• I used route delete 0.0.0.0 in Windows 7 and now i can't connect to my adsl internet

  - by Santiago Sanchez

  I was looking for a way to portfoward 0.0.0.0 default gateways and I found in a Microsoft page that I had to try the command route delete 0.0.0.0, my internet disconnected and I couldn't connect to the internet anymore... Does anyone have a solution? It's an ADSL Modem. I have: Windows 7 x32 4 GB ram A kanji modem that has this problem too... It's like Windows doesn't detect the wireless adapter, so it won't connect to the internet.

  Read the article

• Fiber optic internet, final connection to lan

  - by RayQuang

  Hi, We have fiber optic internet coming to our office soon, and i would like to know if it would be worth installing fiber NIC's in our servers and machines instead of using cat6 gigabit. Here is the layout: (fiber) cable from distribution point in basement - fiber optic modem - Network gateway (debian lenny) - network computers and servers I was wondering if it would be worth installing a fiber connection from the modem to the gateway and the network clients. Will the costs be worth it in terms of speed, latency and stability? Thanks, RayQuang

  Read the article

• Why is Wifi data transfer is slow?

  - by Ali Azam Rana

  I have a wifi router which was attached with my modem, and the pc was connected to the wifi router through an ethernet cable. Yesterday I moved my modem and router to another room and connected my PC with wifi through an external wifi usb dongle (tp-link tl-w722n). I noticed that the file transfer speed from my cell to PC via wifi is greatly affected. I am not clear why is this happening because although PC is now connected through wifi but the dongle supports more than 54Mbps which is still enough.

  Read the article

• How to ping ip dslam which is in other subnet

  - by vito

  I want to ping ip dslam, which is in another subnet The connection is like this: MyPc-----Rj45----------Adsl2+ Modem---------Rj11-------Dslam 192.168.1.4----192.168.1.1---172.80.1.3-------------172.80.1.2 -----------------LanSide-----------WanSide--------------------- The modem is set to Static Ip Address Encapsulation. How can I ping ip dslam with this setup, or what do I need to change about the architecture?

  Read the article

• Comcast SMC Port Forwarding Issue

  - by Zach Fedora

  I have a Comcast SMCD3G modem/router and I've been having issues getting the port to forward - When I check an online "open-port-checker" it says the port is forwarded/they can see the port on my IP. (1 Static IP is assigned to the modem) But when I try to access port 80 for example on a browser, it times out. Also when I try to remote desktop to the server (Windows Server 2008 R2) it doesn't work, yet canyouseeme.org says it is open. Any ideas as to what the problem could be?

  Read the article

• http port 80 slow, while other ports are fine

  - by lydonchandra

  I am using ADSL2+, and the sustained connection can go up to 1.3MB/s, but recently the HTTP connection has been quite slow ( other port i.e. ftp, torrent, etc are fine). I am using Netgear modem/router for my ADSL connection, and am using Netgear switches for my LAN (connected to the modem). What can go wrong and how can I investigate?

  Read the article

• Can I install an x86 version of XP on an acer aspire one

  - by Liam

  I have bought an acer aspire one which has the intel atom processor running linux and am having difficulty getting a 3G USB modem (huwaei e220) working with it. I have spent a significant amount of time trying to get this working but as the modem is not supported on Linux I have now decided to give in and install xp. Is there a specific version of xp that I need for this processor? or can I install the standard x86 version

  Read the article

• ADSL Line rate detected vs download speed

  - by JL

  My modem detects the line rate as 8mbps, but in reality when I use speedtest.net I'm only downloading 7mbps max. Is there a way I can configure my modem to get this extra 1mbps down? Thanks.

  Read the article

• How to make a dial up connection disconnect automatically after downloading + uploading 90 MB data in Windows?

  - by Shanky

  I am using a modem (ZTE USB Modem FFF1) to connect to internet and I want it to disconnect automatically after completing 90 MB (Downloaded data + Uploaded Data). Can anyone suggest how can I do this. I am using a desktop computer running on Windows 8 Consumer Preview. There's no router. I am using a dial up connection to connect. I just want to limit the data usage of my internet connection, considering sent data + received data.

  Read the article

• Wireless won't connect at home but works elsewhere

  - by Jenni

  My laptop connects via a wire into the modem fine and it works without any problems but it wont connect to it wirelessly, when I've taken it out places it connects fine in wifi area's! Also my son has his Wii connected wirelessly to it from his room upstairs without any problems, so I'm not sure where the problem lies, it hasn't worked since we got the modem it did on our old one and phoning Sky is just a waste of time they dont seem to know either and I just keep getting passed round departments repeating myself!

  Read the article

• Internet Pings but Does Not Load

  - by t3techcom18

  From what I've been seeing and been doing my research for the past two days, many people have been having the same issues throughout the years, however, this is the first time I've encountered this issue and many of the specific workarounds or fixes have not worked for me. I've been trying to work through this for 24 hours straight now, but to no avail so many thanks to those that can help. On Monday night, got home from work; surfing the internet for half an hour, everything was fine as always. Just after half an hour, my Internet got very sluggish and then it died completely. I thought it might have been the an update I just put through in terms of Windows Update that said was a critical update for MSE, as the same thing happened a few years ago. I did a System Restore to two different dates that were in the past two weeks, nothing. Uninstalled MSE and disabled Windows Defender and the Windows Firewall: Nothing. Reset IE Options, Reset Winsock, Dumping DNS, many of the other command prompt screens to reset items: Nothing. Reset the modem: Nothing. What DID work, however, was a ping test to Yahoo. The ping test worked, saying all four packets was recieved, yet nothing else popped up. LAN and CenturyLink said everything worked on their end and that everything was connected properly, as well as the speeds working fine. CenturyLink said in their notes that they thought Port 80 was blocked. I went and put in the Firewall to allow Port 80 but it didn't make any difference whatsoever. I remembered I had a spare modem laying around and I switched them up, both modem and the cords - nothing. I then hooked it up to my netbook to see if that would work, as it usually does - connection didn't work there either. Like I said, it's been about 24 hours now and this is increasingly frustrating, as I've tried all solutions (While browsing through 10 search results pages on my phone) suggested and still nothing. Any suggestions and tricks would be greatly appreciated! Here's my specs: Windows 7 32-bit Home Premium Intel Core 2 Duo 3.14 Ghz 4 GB Kingston DDR2 RAM eVGA nForce 750i SLI eVGA GeForce GTX 560 Ti FPB ISP: CenturyLink No router Modem: CenturyLink 660 Series Hardwired connection PLEASE NOTE: This is the only computer I have (Like I said, the netbook solution didn't work), so downloading programs and such is not an option til I get to other computers somewhere else, like right now. Unless someone knows of a way of copying/pasting a file in Windows and then transferring said info to an Android smartphone, this is gunna take a while haha. Patience is requested.

  Read the article

• How can I fix "[Error 6] The handle is invalid." with PySerial

  - by alnorth29

  I'm trying to connect to my phone from my Windows 7 PC using PySerial with the following code: import wmi import serial c = wmi.WMI() modem = c.query("SELECT * FROM Win32_POTSModem").pop() ser = serial.Serial(modem.AttachedTo, modem.MaxBaudRateToSerialPort) try: ser.write('at \r\n') print ser.readline() finally: ser.close() But get the following error on the write call: Traceback (most recent call last): File "D:\Alasdair\Documents\Python Scripts\Phone Interface\test.py", line 14, in <module> ser.write('at \r\n') File "C:\Python26\Lib\site-packages\serial\serialwin32.py", line 255, in write raise SerialException("WriteFile failed (%s)" % ctypes.WinError()) SerialException: WriteFile failed ([Error 6] The handle is invalid.) I've tried connecting with TeraTerm and that works fine, so it's not a problem with the connection to the phone itself. I've been searching around for ages trying to find a solution but haven't come up with anything that works. Any ideas?

  Read the article

• Android delivering different Cell IDs (Neighboring Cell Info)

  - by Curro

  Hello. Using an Android Dev Phone 2, I'm using the GsmCellLocation.getCid() method to get the Cell ID on my network. When I run the command and get all the CellIDs for the NeighboringCellInfo I get this values: 597195726 597185722 597195718 597110191 597101100 597175726 I'm running this using the SDK 1.6. The problem is that when I run the Engineering Mode on a GSM modem that I have, running a command to obtain the Neighboring Cell IDs, I get this values: 34253 0 34223 34262 34181 0 What is the difference here? In what format is Android delivering the Cell IDs? I tried doing a "cell.getCid() & 0xffff" but now I'm getting the values: 21690 31686 37068 11695 11694 31694 Which are still different from the one that the GSM Modem is delivering with the Engineering Mode. Obviously I tried this on at the same time, same location. I'm trying to get the same Cell IDs that the external GSM modem I using is delivering Please provide any help Thanks in advance!

  Read the article

• Can I set up two computers up with the same monitors/keyboard/mouse in a modular way?

  - by CodeJunkie

  I have a desktop computer computer (running Windows 7), and a laptop (running OSX Mountain Lion, and maybe Ubuntu 12 eventually). When the laptop is at home, I want both the desktop and the laptop to use the same (2+) monitors, the keyboard, and the mouse (or mice, if I add a track pad). I know about KVM switches, but I want something more complicated. I like to use Synergy to use both computers with one keyboard and mouse at the same time. Synergy requires that the keyboard and mouse be connected to one computer (the server), which shares them with other computers (clients) over wifi. the issue is that when one computer isn't logged in, Synergy doesn't work on it. Sometimes, I want my laptop to be the server (physically connected to the keyboard and mouse), and sometimes I want my desktop to be the server. This means that I need the keyboard/mouse/other USB devices to be able to switch computers without me playing musical plugs. To complicate things further, I don't always want the same desktop set up in terms of monitors. Sometimes, I want the desktop to have both monitors. Other times, I want the laptop to control both monitors. Sometimes I want the desktop to control one monitor, and the laptop to control the other. In any case, the keyboard and mouse need to be able to be physically connected to either computer without lots of fussing with plugs. This breaks down to at least this set of possible combinations: Desktop controls both monitors, and has a physical connection to keyboard and mouse Laptop controls both monitors, and has a physical connection to keyboard and mouse Desktop and laptop each control a monitor, but the desktop has a physical connection to the keyboard and mouse (which it shares with the laptop via wifi) Desktop and laptop each control a monitor, but the laptop has a physical connection to the keyboard an mouse (which it shares with the desktop via wifi) some usb devices connected via a usb hub need to be able to switch physical connection between computers, ideally without the keyboard and mouse switching computer connection There may be other combinations, but these are the main ones at the moment. Basically, I need a KVM switch which allows me to switch individual monitors/keyboard/mouse/usb hub between computers independently of each other, or a better solution. How can I set two computers up with the same monitors/mice/keyboard/usb hub without having to switch everything to one computer or the other all at the same time?

  Read the article

• Wireless Network Performance Issues

  - by colithium

  My brand new Dell XPS system has been running flawlessly except its abysmal download speeds. I have tried isolating every variable I could possibly think of but I can't figure out the problem. I've talked to Dell and Belkin without making progress (thought I'd try). Here are the speeds: Note that most of the time, upload speeds are actually much faster than download speeds (around 4.0 Mb/s which is better than most other devices on the network) It's not the ISP. The slowdown happens even when transferring files inside the network. Plus every other wireless device gets approximately this: It's not the wireless router. It's a Lynksis WRT160N v1 with the latest firmware (1.02.2). Plus everything else connected to it has normal speeds. It's not the browser. Speeds are the same in IE, FF, and when transferring files with Windows between computers. It's not the wireless adapter. I've tried a Belkin N Wireless USB Adapter (which works fine on another computer) and a Dell Wireless Draft 802.11n WLAN Mini-Card. They have the same slow speeds when connected to the problem computer. It's not the adapter connection. One adapter used USB and the other is a Mini-Card. It's not antenna placement. With the same antenna position and the same device, I get different speeds when connected to the problem computer vs a good computer. Plus everything reports the connection speed as at least 11Mbps and good signal strength. I've tried disabling IPv6 since it sometimes causes weird problems. I've tried disabling Windows Firewall/anti-virus. I've ensured the computer has updated drivers for both adapters. I've ensured that Windows is up to date and so is the BIOS. For the USB adapter I ensured that that USB port functioned at normal speeds with other USB devices. What else could it possibly be? I finally received my copy of Windows 7 and will be trying that. I'd rather not install Windows 7 because of a particular program that will stop working so a solution besides that is welcome. Specs: Vista x64 Core i7 920 6GB RAM 500GB HD GTX 260

  Read the article

• Sony VGN-NR260E "External Device Boot"

  - by user72158

  [A LITTLE BACKGROUND] On all modern Dell computers pushing the F12 on bios boot will allow for a screen that lets you choose what boot option you need. For example if I want to boot off of a USB flash drive to boot into a live Linux distribution in order to clean virus's on netbooks that do not have CD drives to boot from I would push F12 and choose USB device from the list of options. If this does not show up then I can always go to the F2 bios setup and choose flash drive to be the first option. When I restart the computer it will boot into the flash device. I understand that I can purchase an external USB CD drive and then boot from that. I do not want to use that option. The reason for using a flash device instead of a CD is: A: This USB flash device has several different boot OS's on it that are used. B: The antivirus disks are updated often and burning cd's and throwing away others is wasteful compared to simply updating a flash drive. There is nothing wrong with the flash drive. It works perfect on many other PC's. [PROBLEM] Booting this flashdrive has been working for years on hundreds of computers... I just have this ONE computer that I cannot figure out how to get it to boot on... I have a Sony Vaio that will not boot to this device. I've tried pushing every key combo I can think of (F12, Esc, Del, F10...) and none of these key combinations will bring up the boot menu. I chose F2 and went into the bios and changed the first boot device to USB flash device. This did not work either. There is an astrix next to the device and the note states: "This Drive is available when External Device Boot is Enable." [WHAT I NEED] I need to know How to enable External Device Boot on the Sony Vaio VGN-NR260E laptop. OR How to bring up the Boot Menu to allow me to boot off a flash device. Thanks for anyone that can help!

  Read the article

• Be your own cloud [closed]

  - by Jedi

  I have reasonably many electronic gadgets that can go LAN or WI-FI. But how do you share and/or syncronize all your files among them? Well, between my laptops and my desktop I use Dropbox. A nice way to share files among computers. But what if your HDD on your laptop is not large enough to carry music, pictures and films. Normally you would buy an extern USB HDD and store them there, but then you cannot reach the files from other computers which are not connected to the USB device. Many would say I should use a solution like a cloud with a disc station or something like that. But my needs are follows: A mass storage which can be reached among devices (laptops, desktops, iPhone, Android phone, XBox or Playstation). Has low power requirements and is silent. Can be reached inside home and it would be nice if it could be reached outside home as well. Cheap I have looked around and I have found an wireless router which can share a USB device: D-Link Wireless N HD Media Router. I thought it would be an interesting solution for a simple local cloud solution. D-Link uses a little program called SharePort Plus which mount the USB device to your computer. Unfortunately is the transfer rate to the USB storage device rather disappointing. The transfer rate was 5.8 Mbps even though the distance between the laptop and the router was 2 meter. The same is happening when I use cable from the computer to the router. Another thing is that SharePort Plus only allows one computer be connected to the device at a time. The last thing was something I could live with. I have search on the Internet for other solutions and found this video from Synology. I'm not sure if their solution is the right one. I think a disc station connected to my home LAN could the right solution. What have you done in your home to store and share files among your computers and game consoles?

  Read the article

• MacBook Pro Late 2009 SATA Resets, Slowness

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. The resets correlate with AC power connects and disconnects. I don't know if the warnings do. (How do I tell?) Are these bus CRC errors? Or something else? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16 :[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16 :[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16 :[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16 :[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16 :[ 0.813473] scsi0 : ahci 02:37:16 :[ 0.823340] scsi1 : ahci 02:37:16 :[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16 :[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16 :[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16 :[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16 :[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.229570] ata2.00: configured for UDMA/133 02:37:16 :[ 1.240133] ata2: hard resetting link 02:37:16 :[ 1.260738] ata1.00: configured for UDMA/133 02:37:16 :[ 1.280122] ata1: hard resetting link 02:37:16 :[ 1.470125] usb 2-5: new high speed USB device using ehci_hcd and address 3 02:37:16 :[ 1.550165] firewire_core: created device fw0: GUID 58b035fffea99f5c, S800 02:37:16 :[ 1.631306] Initializing USB Mass Storage driver... 02:37:16 :[ 1.631392] scsi6 : usb-storage 2-5:1.0 02:37:16 :[ 1.631454] usbcore: registered new interface driver usb-storage 02:37:16 :[ 1.631455] USB Mass Storage support registered. 02:37:16 :[ 1.960128] usb 4-1: new full speed USB device using ohci_hcd and address 2 02:37:16 :[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.994215] ata2.00: configured for UDMA/133 02:37:16 :[ 1.994220] ata2: EH complete 02:37:16 :[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 2.090773] ata1.00: configured for UDMA/133 02:37:16 :[ 2.090778] ata1: EH complete 02:37:16 :[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16 :[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16 :[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16 :[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16 :[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16 :[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16 :[ 2.091337] sda: 02:37:16 :[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16 :[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16 :[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091756] sdb: sda1 sda2 02:37:16 :[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16 :[ 2.093505] sdb1 sdb2 sdb3 02:37:16 :[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16 :[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16 :[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16 :[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25 :[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25 :[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25 :[ 19.641533] ata1: hard resetting link 02:37:25 :[ 19.642084] ata2: hard resetting link 02:37:26 :[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.396697] ata2.00: configured for UDMA/133 02:37:26 :[ 20.396703] ata2: EH complete 02:37:26 :[ 20.451491] ata1.00: configured for UDMA/133 02:37:26 :[ 20.451498] ata1: EH complete 02:37:30 :[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30 :[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30 :[ 24.627246] ata1: hard resetting link 02:37:30 :[ 24.632250] ata2: hard resetting link 02:37:31 :[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.386782] ata2.00: configured for UDMA/133 02:37:31 :[ 25.386788] ata2: EH complete 02:37:31 :[ 25.431668] ata1.00: configured for UDMA/133 02:37:31 :[ 25.431674] ata1: EH complete 02:45:54 :[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55 :[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55 :[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622583] ata1: hard resetting link 02:45:55 :[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622624] ata2: hard resetting link 02:45:56 :[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.384305] ata2.00: configured for UDMA/133 02:45:56 :[ 530.384314] ata2: EH complete 02:45:56 :[ 530.399225] ata1.00: configured for UDMA/133 02:45:56 :[ 530.399233] ata1: EH complete 02:45:58 :[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58 :[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58 :[ 532.590983] ata1: hard resetting link 02:45:58 :[ 532.591045] ata2: hard resetting link 02:45:59 :[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.344416] ata2.00: configured for UDMA/133 02:45:59 :[ 533.344424] ata2: EH complete 02:45:59 :[ 533.360839] ata1.00: configured for UDMA/133 02:45:59 :[ 533.360847] ata1: EH complete 02:45:59 :[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59 :[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59 :[ 533.660132] ata2: hard resetting link 02:45:59 :[ 533.660151] ata1: hard resetting link 02:46:00 :[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.416768] ata2.00: configured for UDMA/133 02:46:00 :[ 534.416777] ata2: EH complete 02:46:00 :[ 534.431396] ata1.00: configured for UDMA/133 02:46:00 :[ 534.431401] ata1: EH complete 02:46:03 :[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03 :[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03 :[ 537.586002] ata1: hard resetting link 02:46:03 :[ 537.586036] ata2: hard resetting link 02:46:04 :[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.334389] ata2.00: configured for UDMA/133 02:46:04 :[ 538.334398] ata2: EH complete 02:46:04 :[ 538.343511] ata1.00: configured for UDMA/133 02:46:04 :[ 538.343519] ata1: EH complete 02:46:04 :[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04 :[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04 :[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540159] ata1: hard resetting link 02:46:04 :[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540220] ata2: hard resetting link 02:46:05 :[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.294100] ata2.00: configured for UDMA/100 02:46:05 :[ 539.294106] ata2: EH complete 02:46:05 :[ 539.314125] ata1.00: configured for UDMA/100 02:46:05 :[ 539.314132] ------------[ cut here ]------------ 02:46:05 :[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05 :[ 539.314144] Hardware name: MacBookPro5,3 02:46:05 :[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05 :[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05 :[ 539.314224] Call Trace: 02:46:05 :[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05 :[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05 :[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05 :[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05 :[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05 :[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05 :[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05 :[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05 :[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05 :[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05 :[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05 :[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05 :[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05 :[ 539.314296] ata1: EH complete 02:46:12 :[ 547.040117] ata1: hard resetting link 02:46:13 :[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13 :[ 547.408430] ata1.00: configured for UDMA/100 02:46:13 :[ 547.408438] ------------[ cut here ]------------ 02:46:13 :[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13 :[ 547.408451] Hardware name: MacBookPro5,3 02:46:13 :[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13 :[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13 :[ 547.408531] Call Trace: 02:46:13 :[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13 :[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13 :[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13 :[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13 :[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13 :[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13 :[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13 :[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13 :[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13 :[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13 :[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13 :[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13 :[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13 :[ 547.408620] ata1: EH complete 02:46:13 :[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13 :[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13 :[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13 :[ 547.738218] ata1: hard resetting link 02:46:13 :[ 547.738274] ata2: hard resetting link 02:46:14 :[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.486809] ata2.00: configured for UDMA/100 02:46:14 :[ 548.486818] ata2: EH complete 02:46:14 :[ 548.498998] ata1.00: configured for UDMA/33 02:46:14 :[ 548.499004] ata1: EH complete 02:46:18 :[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18 :[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18 :[ 552.529684] ata1: hard resetting link 02:46:18 :[ 552.529723] ata2: hard resetting link 02:46:19 :[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.284141] ata2.00: configured for UDMA/100 02:46:19 :[ 553.284150] ata2: EH complete 02:46:19 :[ 553.301629] ata1.00: configured for UDMA/33 02:46:19 :[ 553.301637] ata1: EH complete 02:46:21 :[ 556.078830] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:21 :[ 556.180361] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:22 :[ 556.262612] ata1: hard resetting link 02:46:22 :[ 556.262617] ata2: hard resetting link 02:46:22 :[ 557.010050] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.010070] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.014069] ata2.00: configured for UDMA/100 02:46:22 :[ 557.014075] ata2: EH complete 02:46:22 :[ 557.023646] ata1.00: configured for UDMA/33 02:46:22 :[ 557.023654] ata1: EH complete 02:46:30 :[ 565.047438] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:30 :[ 565.051554] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:30 :[ 565.108332] ata1: hard resetting link 02:46:30 :[ 565.108389] ata2.00: limiting speed to UDMA/33:PIO4 02:46:30 :[ 565.108406] ata2: hard resetting link 02:46:31 :[ 565.850048] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.850068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.854304] ata2.00: configured for UDMA/33 02:46:31 :[ 565.854313] ata2: EH complete 02:46:31 :[ 565.868477] ata1.00: configured for UDMA/33 02:46:31 :[ 565.868485] ata1: EH complete 02:46:35 :[ 569.265469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:35 :[ 569.268139] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:35 :[ 569.340079] ata1: hard resetting link 02:46:35 :[ 569.340113] ata2: hard resetting link 02:46:35 :[ 570.092568] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.092589] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.096828] ata2.00: configured for UDMA/33 02:46:35 :[ 570.096837] ata2: EH complete 02:46:35 :[ 570.110727] ata1.00: configured for UDMA/33 02:46:35 :[ 570.110735] ata1: EH complete 02:47:04 :[ 598.528232] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:47:04 :[ 598.653973] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:47:04 :[ 598.730854] ata1: hard resetting link 02:47:04 :[ 598.730910] ata2: hard resetting link 02:47:05 :[ 599.480136] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.480159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.484206] ata2.00: configured for UDMA/33 02:47:05 :[ 599.484213] ata2: EH complete 02:47:05 :[ 599.496699] ata1.00: configured for UDMA/33 02:47:05 :[ 599.496707] ata1: EH complete 04:45:59 :[ 7733.756548] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 04:45:59 :[ 7733.882748] EXT4-fs (dm-2): re-mounted. Opts: commit=0 04:45:59 :[ 7733.960142] ata1: hard resetting link 04:45:59 :[ 7733.960189] ata2: hard resetting link 04:46:00 :[ 7734.701926] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.719939] ata1.00: configured for UDMA/33 04:46:00 :[ 7734.719946] ata1: EH complete 04:46:00 :[ 7734.722547] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.726652] ata2.00: configured for UDMA/33 04:46:00 :[ 7734.726659] ata2: EH complete 04:46:02 :[ 7736.656465] ACPI: EC: GPE storm detected, transactions will use polling mode 13:38:49 :[39704.188621] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 13:38:49 :[39704.280588] EXT4-fs (dm-2): re-mounted. Opts: commit=600 13:38:49 :[39704.360819] ata1: hard resetting link 13:38:49 :[39704.360882] ata2: hard resetting link 13:38:50 :[39705.112956] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.114435] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.118673] ata2.00: configured for UDMA/33 13:38:50 :[39705.118682] ata2: EH complete 13:38:50 :[39705.127076] ata1.00: configured for UDMA/33 13:38:50 :[39705.127084] ata1: EH complete 13:39:49 :[39764.142463] applesmc: F1Mn: write arg fail 13:48:11 :[40267.025145] applesmc: FS! : read arg fail 13:52:53 :[40548.596735] applesmc: FS! : read arg fail 13:53:58 :[40613.972856] applesmc: FS! : read arg fail 13:54:08 :[40624.057339] applesmc: FS! : read arg fail 13:58:20 :[40875.397749] applesmc: TC0D: read data fail 14:16:56 :[41991.722054] applesmc: Th2H: read data fail 14:22:32 :[42327.991522] applesmc: light sensor data length set to 10 14:26:19 :[42554.788886] applesmc: F1Mn: write arg fail 14:32:36 :[42931.860443] applesmc: TC0F: read data fail 14:34:32 :[43048.041469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 14:34:33 :[43048.185850] EXT4-fs (dm-2): re-mounted. Opts: commit=0 14:34:33 :[43048.270184] ata1: hard resetting link 14:34:33 :[43048.270224] ata2: hard resetting link 14:34:33 :[43049.030049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.030065] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.034106] ata2.00: configured for UDMA/33 14:34:33 :[43049.034112] ata2: EH complete 14:34:33 :[43049.056952] ata1.00: configured for UDMA/33 14:34:33 :[43049.056959] ------------[ cut here ]------------ 14:34:33 :[43049.056968] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:33 :[43049.056971] Hardware name: MacBookPro5,3 14:34:33 :[43049.056973] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:33 :[43049.057048] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:33 :[43049.057052] Call Trace: 14:34:33 :[43049.057060] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:33 :[43049.057064] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:33 :[43049.057069] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:33 :[43049.057074] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:33 :[43049.057083] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:33 :[43049.057088] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:33 :[43049.057093] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:33 :[43049.057097] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:33 :[43049.057102] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:33 :[43049.057107] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:33 :[43049.057111] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:33 :[43049.057115] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:33 :[43049.057118] ---[ end trace 76dbffc2d5d49d9d ]--- 14:34:33 :[43049.057123] ata1: EH complete 14:34:41 :[43057.012698] ata1: hard resetting link 14:34:42 :[43057.362780] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:42 :[43057.381432] ata1.00: configured for UDMA/33 14:34:42 :[43057.381441] ------------[ cut here ]------------ 14:34:42 :[43057.381450] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:42 :[43057.381453] Hardware name: MacBookPro5,3 14:34:42 :[43057.381455] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:42 :[43057.381530] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:42 :[43057.381533] Call Trace: 14:34:42 :[43057.381542] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:42 :[43057.381546] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:42 :[43057.381551] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:42 :[43057.381556] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:42 :[43057.381565] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:42 :[43057.381569] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:42 :[43057.381575] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:42 :[43057.381579] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:42 :[43057.381584] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:42 :[43057.381589] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:42 :[43057.381594] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:42 :[43057.381598] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:42 :[43057.381601] ---[ end trace 76dbffc2d5d49d9e ]--- 14:34:42 :[43057.381624] ata1: EH complete 14:34:42 :[43057.557887] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:42 :[43057.560517] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:42 :[43057.621194] ata1: hard resetting link 14:34:42 :[43057.621252] ata2: hard resetting link 14:34:43 :[43058.370141] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.370162] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.374407] ata2.00: configured for UDMA/33 14:34:43 :[43058.374415] ata2: EH complete 14:34:43 :[43058.381989] ata1.00: configured for UDMA/33 14:34:43 :[43058.381996] ata1: EH complete 14:34:43 :[43058.616228] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:43 :[43058.618931] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:43 :[43058.626687] ata1: hard resetting link 14:34:43 :[43058.626731] ata2: hard resetting link 14:34:44 :[43059.372908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.372932] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.376997] ata2.00: configured for UDMA/33 14:34:44 :[43059.377003] ata2: EH complete 14:34:44 :[43059.392576] ata1.00: configured for UDMA/33 14:34:44 :[43059.392585] ata1: EH complete 15:48:19 :[47474.710860] ata1: hard resetting link 15:48:19 :[47474.710882] ata2: hard resetting link 15:48:20 :[47475.460144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.460169] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.473709] ata1.00: configured for UDMA/33 15:48:20 :[47475.473717] ata1: EH complete 15:48:20 :[47475.727960] ata2.00: configured for UDMA/33 15:48:20 :[47475.727969] ata2: EH complete 16:29:39 :[49954.295017] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 16:29:39 :[49954.622307] EXT4-fs (dm-2): re-mounted. Opts: commit=0 16:29:39 :[49954.710139] ata1: hard resetting link 16:29:39 :[49954.710174] ata2: hard resetting link 16:29:40 :[49955.460046] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.460062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.464138] ata2.00: configured for UDMA/33 16:29:40 :[49955.464144] ata2: EH complete 16:29:40 :[49955.473251] ata1.00: configured for UDMA/33 16:29:40 :[49955.473258] ata1: EH complete

  Read the article

• How do you preseed an ssh key?

  - by Wes Felter

  I tried this: d-i preseed/late_command string mkdir -p /target/root/.ssh d-i preseed/late_command string cp /cdrom/id_rsa.pub /target/root/.ssh/authorized_keys d-i preseed/late_command string chmod -R go-rwx /target/root/.ssh (I'm using a USB installer and I put id_rsa.pub in the root directory of the USB drive.) The /root/.ssh directory is not created and the installer complains that the chmod command failed (not surprising if the directory doesn't exist).

  Read the article

• How to boot with Intel GMA500 Poulsbo graphics

  - by Seyed Mohammad

  I have a Sony VAIO netbook with Intel GMA-500 Poulsbo Graphics and I'm trying to boot the latest Ubuntu-12.04 Beta-2 using a bootable USB. According to this Ubuntu-Wiki, support for Intel GMA-500 Poulsbo graphics is promising in Precise-Beta2 and should work out of the box. Of course the wiki talks about a problem when booting from USB and states that restarting X using: sudo service lightdm restart will bring a functional graphical desktop, but nothing happens for me! Any help is highly appreciated.

  Read the article

• Problem booting 12.04-Beta2 with Intel GMA500 Poulsbo graphics

  - by Seyed Mohammad

  I have a Sony VAIO netbook with Intel GMA-500 Poulsbo Graphics and I'm trying to boot the latest Ubuntu-12.04 Beta-2 using a bootable USB. According to this Ubuntu-Wiki, support for Intel GMA-500 Poulsbo graphics is promising in Precise-Beta2 and should work out of the box. Of course the wiki talks about a problem when booting from USB and states that restarting X using: sudo service lightdm restart will bring a functional graphical desktop, but nothing happens for me! Any help is highly appreciated.

  Read the article

• How can fix HDMI HDTV overscan when I my TV has no aspect ratio setting?

  - by Colin Dean

  I have a 32" Vizio HDTV. It's a few years old, but running well. I just connected a new nettop to it using HDMI out. It's the Intel 3x00 graphics chipset. I'm seeing overscan, where the resolution in Ubuntu is set to 1280x720, but the TV itself is 1366x768. When I go into the Monitors control applet, I cannot change the resolution to anything other than the current or 640x480. A user had a similar overscan problem, but fixed the overscan by adjusting his TV's aspect ratio settings. I do not have that luxury. Is there a way I can do this without having to delve into xorg.conf or other command-line craziness? I'm more than comfortable doing so, but there must be a cleaner way. I'm running Ubuntu Natty, keeping up with updates and such. Here's the output of lspci: colin@bricktop:~$ lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:04.0 Signal processing controller: Intel Corporation Core Processor Thermal Management Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) 03:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Ubuntu turns off instead of suspend / sleeping

  - by Marcos

  I'm using Ubuntu 11.10 on my notebook as the main OS. How ever, I've been facing a serious problem: Every time I try to suspend it, or it just stays idle for a while, the computer shuts down, instead of suspending. It actually seems to be suspended, but when I press the button the awake it, it turns on, the open works are all lost. How can i fix this? P.s: On windows 7 the suspend / sleep resumes just fine. Here is a complete list of hardware: 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB Controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b4) 00:1c.2 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 [8086:1c14] (rev b4) 00:1d.0 USB Controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) 01:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 02:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2382] (rev 80) 02:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2381] (rev 80) 02:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2383] (rev 80) 02:00.5 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 03) I've updated the kernel to 3.2 still and hibernate or suspend is still not working. SWAP is 1/4 of my RAM.

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >