Search Results

Search found 4248 results on 170 pages for 'adsl router'.

Page 129/170 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• dd-wrt Bonjour/ netbios etc on two subnets

  - by user72182

  Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

  Read the article

• Hosting 3 domains on 3 PC (1 domain per PC) with only 1 static IP address

  - by StealthRT

  Hey all i am trying to figure this out here. I have 3 PC's that are hooked into my router which i have a static IP for. I am currently hosting a web site (ex: blah1.com) on the 1st PC but have yet to connect PC 2 and 3 up to the network. That one PC thats online is using port 77. I direct all 80 traffic to port 77 using that servers IP address (192.168.x.xxx) My question is, how can i direct traffic for my other 2 domains (ex: blah2.com and blah3.com) to the 2 individual PC's (ip's) as i already am doing with the 1st PC if i can only use one port 80 to direct taffic to the website in?

  Read the article

• Nagios check_bgp_neighbors plugin showing critical status

  - by user141610

  I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C snmpName -n xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. Status information: line: neighbor:xx.xx.xx.50:sent:78838:received:9769 Failed: status:6 prefixes:16 sent:0 received:1 Log [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-email;line: neighbor:103.7.248.50:sent:78842:received:9772 [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-sms;line: neighbor:103.7.248.50:sent:78842:received:9772 Why does it show critical status???? I am not getting response for this question, if you need additional information please mention it in comment.

  Read the article

• Why does WebDAV fail from inside home network

  - by Claus

  On my OSX server there is a folder that is configured in the Server App to be accessible via WebDAV. This folder is used to sync OmniFocus. On my router, I have set up a dynamic dns. When I am outside my home network (physically away or when connected via a vpn), I can connect and sync fine via: https://<server name from dyndns>/<username>/<path to WebDAV folder> However, when I am in my home network, the connection to WebDAV does not work (other connections, AFP, f.ex, do work). What could be some reasons why I can't connect to WebDAV from within my home network? What log files could give hints and where are they stored? I am running OSX server 10.9.3. and server.app. Thanks for your help.

  Read the article

• How do I configure tinydns (with fefe's IPv6 patch) to listen on IPv6 address?

  - by Christian Hudon

  I'm setting up my network to support IPv6. I have static IPv6 addresses assigned to each interface of my router, and radvd advertising different prefixes on each interface. The next step would be to get my dnscache (from djbdns) working on IPv6. Said dnscache has fefe's IPv6 patch applied, so I assume it should work with IPv6. However, I can't find any documentation online on how to make the patched dnscache listen on IPv6. How do I configure tinydns and dnscache to listen on IPv6 too?

  Read the article

• Purpose of LAN Domain?

  - by Leonard Thieu

  What is the purpose of creating a domain name for your LAN? I'm using DD-WRT on my router and assigned local.moofz.com as the LAN domain. I setup Apache HTTP servers on two of the computers on my LAN to test it out. I could reach them on oneil.local.moofz.com and vala.local.moofz.com, but I found out that I could also reach them via their hostnames oneil and vala. If I can reach them through their host names, then what would be the purpose of having a domain name for my LAN?

  Read the article

• Resolving real IP address out of a dynamic dns address

  - by stavnir

  I recently opened a dynamic dns user (at no-ip for that matter..) for my own personal needs and especially for ssh-ing my computer whenever I need to, without knowing it's static IP. My questions are: Am I misusing the concept of dynamic dns? Are there more appropriate methods to do what I want to do? If not, how do I resolve my router's real ip address? Firefox somehow manages to do so, nslookup and other similar commands only resolve the ip of the ddns server (e.g. no-ip.org). Trying to figure this mystery with wireshark failed miserably ;)

  Read the article

• Error while setting up Anywhere Access on Windows Server 2012 Essential (personalized domain name from Microsoft)

  - by Thomas

  I am trying to setup Anywhere Access on a Windows Server 2012 Essential Release Candidate, but keep getting this error: "The domain name was not setup for your server. Wait a few minutes and run the wizard again. An unknown error occurred. Please wait a few minutes and then try again". These are the options that I selected in the Wizard: I want to set up a new domain name Get a personalized domain name from Microsoft Entered my Windows live id and password xxxx.remotewebaccess.com And on the next page the error is displayed. I have setup my router (Linksys WRT160N) to forward all TCP traffic to the Server. UPnP is also enabled. If I hit my public (dynamic) IP (http://188.182.194.182/) I get the Windows Server 2012 homepage. Any ideas?

  Read the article

• D-Link DNS-323 NAS firmware update

  - by Mark Beaton

  Hi all, I've got a D-Link DNS-323 NAS enclosure holding a bunch of multimedia files that I've (possibly stupidly) just updated the firmware on, from 1.03 to 1.08. The updater indicated it applied the firmware patch successfully, but after rebooting it I can no longer get into it via the web interface, either via the static IP I had assigned it before the update, or by any of the DHCP-assigned addresses that I can see are currently assigned by my router. The unit just sits there, with the drives (2x512 set up as RAID-1) thrashing away seemingly forever... So, my question - has anyone had a similar experience with one of these units? Any advice etc? I've googled the hell out of it, and can't find anything useful.

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• Does a USB to RJ-45 console cable exist?

  - by Carl Flippin

  I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• Microsoft Forefront Management Gateway 2010 - Which topology to choose for monitoring only server?

  - by MadBoy

  Hello, I've installed Forefront and wanted to use it as monitoring traffic solution until we decide to put it as a router. I've 2 nic's assigned to this virtual machine. One NIC has connected port which is "mirror port" of our WAN redirected on switch so it sees all the network traffic flying by. The other NIC is internet access. This server is located inside our lan network. What topology should i choose and which options I should look at to be able to see which traffic is used (SMTP, WWW etc) and who does what? We had cases of infected machines with spam and we want to be able to see that some machine is sending large amounts of mails. Is that possible ?

  Read the article

• Trouble accessing network drives in Windows 7

  - by Warlax

  Hi, Recently purchased a LaCiE network drive. Connected it to my router, configured it, added a user for myself. Installed the "Network Assistant" that came with it - no problem. Went to My Computer Network, found the network drive - was prompted for a login/password to see the contents, types \user and password (leading slash to get rid of DOMAIN) and accesses contents. There is one open share that I can access/mount without problem and there's another share with my user name as set-up via the network drive's web-based config. Double-clicked on that, prompted again. user/password doesn't work! It says I have no permissions but the user/pass combination is PERFECT. Some Windows Vista posts talk about a Local Security Policy menu - but that's nowhere to be found. Any ideas? (Windows 7 Professional BTW).

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• Windows 7 Utlimate x64 - No Internet access

  - by rafek

  I've just installed Windows 7 Ultimate x64. As all of my computers at home I've connected to my router via wifi (open/wep). And what has happened is that Wireless Connection is Connected but with No Internet access -- my ipconfig says: Autoconfiguration IPv4 Address : 169.254.33.161 Subnet Mask : 255.255.0.0 Default Gatewawy : (empty) After ipconfig /renew I get: An error occurred while renewing interface Wireless Network Connection : unable to contact your DHCP server. Request has timed out. [..] I'm looking for a solution for 2 hours now...

  Read the article

• IP Address on internet access shared over ad-hoc wifi network

  - by Jacxel

  The Situation When im staying at my girlfriends we both like to have internet access on our laptops but her accommodation don't allow wireless routers. My Question My question is if I set up an Ad-Hoc network to share the internet connection as shown here on How To Geek. Will my laptop be acting as a wireless router or will the connection all go through my laptop as one ip address so it appears to be my computer accessing the webpages etc, that my girlfriend actually is. i would be interested in knowing any additional information that could help sove this problem eg. if connectify would do what i want.

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers? What we ended up doing In case anyone are courious, we ended up doing seperate VLANs for each user. And as a matter of fact, not just the 550 users, but for 2500 users (11 dorms). Here's a page describing the setup: http://k-net.dk/technicalsetup/ (the section "Transparent firewall using VLANs"). There was no significant load on the router server as I feared in one of the comments below. Even at 800Mpbs.

  Read the article

• Blocking ports on the public IP assigned to lo interface in GNU/Linux

  - by nixnotwin

  I have setup my Ubuntu server as a router and webserver by following the answer given here. My ISP facing interface eth0 has a private 172.16.x.x/30 ip and my lo interface has a public IP as mentioned in the answer to the question linked above. The setup is working well. The only snag I have experienced is that I could not find a way to block the ports exposed by the public IP on the lo interface. I tried doing iptables -A INPUT -i eth0 -j DROP, and my server lost connectivity to the public network (internet). I could not ping any public ips. What I want is a way to block ports that are exposed by the public ip on the lo interface. And also I require iptables rules that can expose ports like 80 or openvpn port to the public network.

  Read the article

• Access Methods to a computer Using MAC Address

  - by Dimal Chandrasiri

  I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

  Read the article

• unusual webpage access problem

  - by user28163

  This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

  Read the article

• Making internal website available publicly (Win 2008 Server)

  - by endigo

  I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

  Read the article

• How to go about scheduling a task in windows 7 to change wireless connection

  - by Skindeep2366

  This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >