Search Results

Search found 16980 results on 680 pages for 'home edition'.

Page 129/680 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• Determining cause of high NFS/IO utilization without iotop

  - by Matt

  I have a server that is doing an NFSv4 export for user's home directories. There are roughly 25 users (mostly developers/analysts) and about 40 servers mounting the home directory export. Performance is miserable, with users often seeing multi-second lags for simple commands (like ls, or writing a small text file). Sometimes the home directory mount completely hangs for minutes, with users getting "permission denied" errors. The hardware is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for the home directories. What I find curious, and suspicious, is that the sda device often has very high utilization, even though it only contains the OS. I would expect this virtual drive to be idle almost all the time. The system is not swapping, according to "free" and "vmstat". Why would there be major load on this device? Here is a 30-second snapshot from iostat: Time: 09:37:28 AM Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 44.09 0.03 107.76 0.13 607.40 11.27 0.89 8.27 7.27 78.35 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 44.09 0.03 107.76 0.13 607.40 11.27 0.89 8.27 7.27 78.35 sdb 0.00 2616.53 0.67 157.88 2.80 11098.83 140.04 8.57 54.08 4.21 66.68 sdb1 0.00 2616.53 0.67 157.88 2.80 11098.83 140.04 8.57 54.08 4.21 66.68 dm-0 0.00 0.00 0.03 151.82 0.13 607.26 8.00 1.25 8.23 5.16 78.35 dm-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-2 0.00 0.00 0.67 2774.84 2.80 11099.37 8.00 474.30 170.89 0.24 66.84 dm-3 0.00 0.00 0.67 2774.84 2.80 11099.37 8.00 474.30 170.89 0.24 66.84 Looks like iotop is the ideal tool to use to sniff out these kinds of issues. But I'm on CentOS 5.6, which doesn't have a new enough kernel to support that program. I looked at Determining which process is causing heavy disk I/O?, and besides iotop, one of the suggestions said to do a "echo 1 /proc/sys/vm/block_dump". I did that (after directing kernel messages to tempfs). In about 13 minutes I had about 700k reads or writes, roughly half from kjournald and the other half from nfsd: # egrep " kernel: .*(READ|WRITE)" messages | wc -l 768439 # egrep " kernel: kjournald.*(READ|WRITE)" messages | wc -l 403615 # egrep " kernel: nfsd.*(READ|WRITE)" messages | wc -l 314028 For what it's worth, for the last hour, utilization has constantly been over 90% for the home directory drive. My 30-second iostat keeps showing output like this: Time: 09:36:30 PM Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await svctm %util sda 0.00 6.46 0.20 11.33 0.80 71.71 12.58 0.24 20.53 14.37 16.56 sda1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 sda2 0.00 6.46 0.20 11.33 0.80 71.71 12.58 0.24 20.53 14.37 16.56 sdb 137.29 7.00 549.92 3.80 22817.19 43.19 82.57 3.02 5.45 1.74 96.32 sdb1 137.29 7.00 549.92 3.80 22817.19 43.19 82.57 3.02 5.45 1.74 96.32 dm-0 0.00 0.00 0.20 17.76 0.80 71.04 8.00 0.38 21.21 9.22 16.57 dm-1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 dm-2 0.00 0.00 687.47 10.80 22817.19 43.19 65.48 4.62 6.61 1.43 99.81 dm-3 0.00 0.00 687.47 10.80 22817.19 43.19 65.48 4.62 6.61 1.43 99.82

  Read the article

• How to configure DNS Server on Fedora

  - by user863873

  I want to learn how to configure my home PC server into a web server with domain and host. My IP is 109.99.141.133 and now points to a phpinfo page host on my home server. My registed domain is: anunta-anunturi.ro I searched for a tutorial and I've read that I have to configure /etc/named.conf and the file sources for the new zone that I create. So, from the tutorials, my /etc/named.conf looks like this: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { localhost; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "anunta-anunturi.ro" IN { type master; file "/etc/anunta-anunturi.db"; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; My /etc/anunta-anunturi.db file looks like this — I'm not sure if this is okay, or if it's the easy one. $TTL 86400 anunta-anunturi.ro. IN SOA serveur.anunta-anunturi.ro. root.serveur.anunta-anunturi.ro. ( 1997022700 ; Serial 28800 ; Refresh 14400 ; Retry 3600000 ; Expire 86400 ) ; Minumun IN NS serveur.anunta-anunturi.ro. IN MX 10 mail.anunta-anunturi.ro. serveur.anunta-anunturi.ro. IN A 192.168.1.37 www.anunta-anunturi.ro. IN A 192.168.1.37 mail.anunta-anunturi.ro. IN A 192.168.1.37 Extra info: At home I receive internet from my ISP through a router. My home PC and server recieve their IP automatically from the router when I start/restart. In my local home network, my server receives the IP 192.168.1.37 from the router. When I enter 109.99.141.133 in my browser, it points to the rooter that forwards port 80 to local IP 192.168.1.37 (my home server) Questions: Are my two files good? What/where is my nameserver that I need to copy/paste to my top level domain (where I registered my domain: rotld.ro)?

  Read the article

• NFS Mounts Issues

  - by user554005

  Having some issue with a NFS Setup on the clients it just times out refuses to connect [root@host9 ~]# mount 192.168.0.17:/home/export /mnt/export mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). mount: mount to NFS server '192.168.0.17' failed: timed out (retrying). Here are the settings I'm using: [root@host17 /home/export]# cat /etc/hosts.allow # # hosts.allow This file contains access rules which are used to # allow or deny connections to network services that # either use the tcp_wrappers library or that have been # started through a tcp_wrappers-enabled xinetd. # # See 'man 5 hosts_options' and 'man 5 hosts_access' # for information on rule syntax. # See 'man tcpd' for information on tcp_wrappers # portmap: 192.168.0.0/255.255.255.0 lockd: 192.168.0.0/255.255.255.0 rquotad: 192.168.0.0/255.255.255.0 mountd: 192.168.0.0/255.255.255.0 statd: 192.168.0.0/255.255.255.0 [root@host17 /home/export]# cat /etc/hosts.deny # # hosts.deny This file contains access rules which are used to # deny connections to network services that either use # the tcp_wrappers library or that have been # started through a tcp_wrappers-enabled xinetd. # # The rules in this file can also be set up in # /etc/hosts.allow with a 'deny' option instead. # # See 'man 5 hosts_options' and 'man 5 hosts_access' # for information on rule syntax. # See 'man tcpd' for information on tcp_wrappers # portmap:ALL lockd:ALL mountd:ALL rquotad:ALL statd:ALL [root@host17 /home/export]# cat /etc/exports /home/export 192.168.0.0/255.255.255.0(rw) [root@host17 /home/export]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain RH-Firewall-1-INPUT (2 references) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT icmp -- anywhere anywhere icmp any ACCEPT esp -- anywhere anywhere ACCEPT ah -- anywhere anywhere ACCEPT udp -- anywhere 224.0.0.251 udp dpt:mdns ACCEPT udp -- anywhere anywhere udp dpt:ipp ACCEPT tcp -- anywhere anywhere tcp dpt:ipp ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:http ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:https ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:6379 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:sunrpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:sunrpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:nfs ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:32803 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:filenet-rpc ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:892 ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:892 ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:rquotad ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:rquotad ACCEPT tcp -- 192.168.0.0/24 anywhere state NEW tcp dpt:pftp ACCEPT udp -- 192.168.0.0/24 anywhere state NEW udp dpt:pftp REJECT all -- anywhere anywhere reject-with icmp-host-prohibited on the clients here is some rpcinfos [root@host9 ~]# rpcinfo -p 192.168.0.17 program vers proto port 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100011 1 udp 875 rquotad 100011 2 udp 875 rquotad 100011 1 tcp 875 rquotad 100011 2 tcp 875 rquotad 100005 1 udp 45857 mountd 100005 1 tcp 55772 mountd 100005 2 udp 34021 mountd 100005 2 tcp 59542 mountd 100005 3 udp 60930 mountd 100005 3 tcp 53086 mountd 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100227 2 udp 2049 nfs_acl 100227 3 udp 2049 nfs_acl 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100227 2 tcp 2049 nfs_acl 100227 3 tcp 2049 nfs_acl 100021 1 udp 59832 nlockmgr 100021 3 udp 59832 nlockmgr 100021 4 udp 59832 nlockmgr 100021 1 tcp 36140 nlockmgr 100021 3 tcp 36140 nlockmgr 100021 4 tcp 36140 nlockmgr 100024 1 udp 46494 status 100024 1 tcp 49672 status [root@host9 ~]# [root@host9 ~]# rpcinfo -u 192.168.0.17 nfs rpcinfo: RPC: Timed out program 100003 version 0 is not available [root@host9 ~]# rpcinfo -u 192.168.0.17 portmap program 100000 version 2 ready and waiting program 100000 version 3 ready and waiting program 100000 version 4 ready and waiting [root@host9 ~]# rpcinfo -u 192.168.0.17 mount rpcinfo: RPC: Timed out program 100005 version 0 is not available [root@host9 ~]# I'm running CentOS 5.8 on all systems

  Read the article

• Nginx and multiple wordpress instances with fastcgi under same domain

  - by damnsweet

  My site is running on apache. two instances of wordpress exist under paths /tr/ and /eng/. I want to move the setup to nginx but could not manage to get it working. My setup consists of nging 0.7.66, php 5.3.2, and php-fpm. /tr/ and /eng/ are two separate wordpress instances located under /home/istci/webapps/wordpress_tr and /home/istci/webapps/wordpress respectively. Below is the server section from nginx.conf containing only configuration for tr, yet could not get it working either. server { listen 80; server_name www.example.com; charset utf-8; location ~ ^/$ { rewrite ^(.+)$ http://www.example.com/tr/ permanent; } location ~ /tr/.*php$ { fastcgi_pass unix:/home/istci/var/run/wptr.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/istci/webapps/wordpress_tr$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; } location /tr/ { root /home/istci/webapps/wordpress_tr/; index index.php index.html index.htm; if (!-e $request_filename) { rewrite ^(.+)$ /tr/index.php?q=$1 last; break; } if (-f $request_filename) { expires 30d; break; } } } php-fpm listens on unix:/home/istci/var/run/wptr.sock. running it in debug-mode shows no active handlers, which means no connection is made to unix socket from nginx. nginx access logs: 127.0.0.1 - - [09/Jun/2010:03:45:11 -0500] "GET /tr/ HTTP/1.0" 404 20 "-" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.2.4) Gecko/20100527 Firefox/3.6.4" nginx debug logs : 2010/06/09 03:38:53 [notice] 6922#0: built by gcc 4.1.2 20080704 (Red Hat 4.1.2-48) 2010/06/09 03:38:53 [notice] 6922#0: OS: Linux 2.6.18-164.9.1.el5PAE 2010/06/09 03:38:53 [notice] 6922#0: getrlimit(RLIMIT_NOFILE): 4096:4096 2010/06/09 03:38:53 [notice] 6923#0: start worker processes 2010/06/09 03:38:53 [notice] 6923#0: start worker process 6924 2010/06/09 03:38:53 [notice] 6923#0: start worker process 6925 2010/06/09 03:39:01 [notice] 6925#0: *1 "^(.+)$" matches "/tr/", client: 127.0.0.1, server: www.example.com, request: "GET /tr/ HTTP/1.0", host: "www.example.com" 2010/06/09 03:39:01 [notice] 6925#0: *1 rewritten data: "/tr/index.php", args: "q=/tr/", client: 127.0.0.1, server: www.example.com, request: "GET /tr/ HTTP/1.0", host: "www.example.com" Any clues about what is wrong with my configuration? Thanks.

  Read the article

• ubuntu mount iso but some files are unreadable

  - by Chao

  I'm new to Linux and just installed ubuntu 12.04 amd64 this month. I had failed installing Texlive with texlive2012 iso image. I used the recommended command to mount: "mount -t iso9660 -o ro,loop,noauto /your/texlive2012.iso /mnt " But the installer failed to read some file. The iso is fine, I checked the md5. I extracted everything from iso with archive manager, and it installed successfully. So, why mount is not working? Thanks. UPDATE with furius iso mount tool, mount with Fuse, and it installed, with warning: Summary of warning messages during installation: Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. While mount with Loop, it failed to install. Updated Error message from terminal, mounted with furius iso mount, loop. texlive2012-20120701_iso$ ./install-tl -gui Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] ... Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. ./tlpkg/installer/xz/xzdec.x86_64-linux: (stdin): File is corrupt tar: Unexpected EOF in archive tar: rmtlseek not stopped at a record boundary tar: Error is not recoverable: exiting now untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] ./install-tl: Could not write to install-tl.log, so flushing messages to stderr. Loading ./tlpkg/texlive.tlpdb Installing TeX Live 2012 from: . Platform: x86_64-linux = 'x86_64 with GNU/Linux' Distribution: inst (compressed) Directory for temporary files: /tmp Installer revision: 26794 Database revision: 26935 Installing [0001/2481, time/total: ??:??/??:??]: 12many [3k] Installing [0002/2481, time/total: 00:00/00:00]: 2up [4k] Installing [0003/2481, time/total: 00:00/00:00]: Asana-Math [457k] Installing [0004/2481, time/total: 00:00/00:00]: ESIEEcv [2k] Installing [0005/2481, time/total: 00:00/00:00]: FAQ-en [1k] ... Installing [0262/2481, time/total: 00:10/01:09]: c90 [2k] Installing [0263/2481, time/total: 00:10/01:09]: cachepic [5k] Installing [0264/2481, time/total: 00:10/01:09]: cachepic.x86_64-linux [1k] Installing [0265/2481, time/total: 00:10/01:09]: calctab [5k] Installing [0266/2481, time/total: 00:10/01:09]: calligra [42k] Installing [0267/2481, time/total: 00:10/01:09]: calligra-type1 [59k] Downloaded ./archive/calligra-type1.tar.xz, size equal, but md5sum differs; downloading again. untar: untarring /home/lichao/ttt/temp/calligra-type1.tar failed (in /home/lichao/ttt/texmf-dist) untarring /home/lichao/ttt/temp/calligra-type1.tar failed, stopping install. Installation failed. Rerunning the installer will try to restart the installation. Or you can restart by running the installer with: install-tl --profile installation.profile [EXTRA-ARGS] Segmentation fault (core dumped) I am sure that the iso is fine. I can open it with archive manager and all files are good. But after mounting it, even archive manager failed to open some files (which can be opened when the iso is opened in archive manager).

  Read the article

• How do bots access directories on a server that are not DocumentRoot of public IP address? How do I stop them?

  - by tmsimont

  I have a local network set up with apache2 and "named" running on OpenSuse 13.1 Linux. I used the "named" service to use my computer as a domain server. I set up my router to point to ask my computer for domain lookups, so I have a chance to have it rewrite a bunch of domains on my network to its own local IP, 192.168.0.111 This works great. I use virtual host configuration to allow various domains and subdomains (re-routed to the same IP via named) to pull up different directories in my computer. For example: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias fmb.wa.net DocumentRoot /home/work/wa.net/fmb </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias postrecord.wa.net DocumentRoot /home/work/wa.net/postrecord </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias cvalley.wa.net DocumentRoot /home/work/wa.net/cvalley_local </VirtualHost> This makes it possible for me to hit cvalley.wa.net from any device in my network and get the site that lives in /home/work/wa.net/cvalley_local I decided to forward port 80 to this computer, so I could share a few development sites with coworkers. I can't control which site they see with the same named service, because they'd have to use my computer as their domain name server... So I added a line like this: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias MY.IP.XXX.XX DocumentRoot /home/work/wa.net/cvalley </VirtualHost> Where "MY.IP.XXX.XX" is my public IP address. This works as expected, when you hit my IP address from a public network you see the site that lives in /home/work/wa.net/cvalley. The point of confusion that I have is that there are public IP addresses in my logs in other sites. I would have expected it to be impossible to access other sites in my network, unless the public user somehow figured out what I'm calling my ServerAliases, and is mimicing my domain set up... How can public traffic be hitting my other local sites? How can I recreate this kind of access? Here are some examples of public IP's hitting my VirtualHost sites: 162.253.66.76 - - [15/Aug/2014:19:20:47 -0600] "GET /xmlrpc.php HTTP/1.0" 404 1004 "-" "-" 162.253.66.74 - - [16/Aug/2014:10:50:28 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 185.4.227.194 - - [16/Aug/2014:11:16:45 -0600] "GET http://24x7-allrequestsallowed.com/?PHPSESSID=1rysxtj500143WQMVT%5E_NAZ%5BQ HTTP/1.1" 200 262 "-" "-" 101.226.254.138 - - [16/Aug/2014:13:32:14 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 162.253.66.74 - - [16/Aug/2014:14:26:19 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 212.129.2.119 - - [16/Aug/2014:16:00:51 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 91.240.163.111 - - [16/Aug/2014:18:34:32 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 162.253.66.74 - - [16/Aug/2014:19:02:53 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 122.226.223.69 - - [17/Aug/2014:05:53:09 -0600] "GET http://www.k2proxy.com//hello.html HTTP/1.1" 404 1006 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/6.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E)" ::1 - - [17/Aug/2014:10:19:26 -0600] "OPTIONS * HTTP/1.0" 200 - "-" "Apache/2.4.6 (Linux/SUSE) OpenSSL/1.0.1e PHP/5.4.20 (internal dummy connection)" 162.209.65.196 - - [17/Aug/2014:15:31:53 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 111.206.199.163 - - [18/Aug/2014:11:12:56 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 37.187.180.168 - - [18/Aug/2014:15:40:00 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 62.210.38.226 - - [18/Aug/2014:18:35:16 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" Is there anything that I can do to reliably deny public access by default, but allow it only in one VirtualHost?

  Read the article

• Windows Server 2008 / SQL 2008 Licensing for Authenticated Web Application

  - by MikeM

  Hello, I'm trying to crunch some numbers to see what the software costs involved are for hosting an application we are developing. Users will not be anonymous - they will need to log in. SQL Server 2008: SQL Server licensing is easy - it will be licensed per-processor. No real fuss there. The cost of CALs would be much higher for the number of users as compared to the processor licenses. Windows Server 2008: This is where it gets trickier. We need to license the OS for both the web servers (there will be a couple) plus the database servers (also a couple). The Web Servers could run on the Web Edition without a need for CALs, but if you continue reading, you will see that may not matter much because I will likely have user CALs for each user anyway. We can't use the "External Connector" for any of the Windows licenses, because that doesn't cover customers who are paying to access a hosted application. We can't use the Web Edition for the SQL Servers because that license only allows database running on Web Edition to host data for the local web application (i.e. other web servers can't connect to it). So that leaves us with the "full" editions of Windows Server for the database server OS. I find this a little rediculous, and I feel as though I must be missing something, but it looks to me like I will actually need to buy a CAL for every user who signs up to use our service. I feel like I'm missing something because that means that for every user, I have to shell out $40 for a CAL. That could be one or two years' worth of revenue from each user for an inexpensive service! Is there any way to serve a web application to authenticated users without paying for individual Windows Server CALs, if the web servers and SQL servers are seperate boxes?

  Read the article

• How to use cyg-wrapper to fork a new tab in win32 gvim

  - by Peter Nore

  I would like to set up an alias in my cygwin .bashrc that translates pathnames unix-to-dos and passes them to windows gvim in a new tab of an existing instance. I am trying to use Luc Hermitte's cyg-wrapper script for running native win32 applications from Cygwin as per this vim tip. Luc's example of how to use his script is: alias vi= 'cyg-wrapper.sh "C:/Progra~1/Edition/vim/vim63/gvim.exe" --binary-opt=-c,--cmd,-T,-t,--servername,--remote-send,--remote-expr' I do not understand this example because most of these vim parameters (-c,--cmd,--servername,--remote-send,--remote-expr, etc) require more information, and I have not found any example of how to supply the additional information to cyg-wrapper.sh. For example, calling C:/Progra~1/Edition/vim/vim63/gvim.exe --servername=GVIM --remote-tab-silent file1 & will open file1 in a new tab of existing (or non existing) instance GVIM, but calling gvim --servername accomplishes nothing on its own. Unfortunately, though, the corresponding cyg-wrapper phrase does not work: cyg-wrapper.sh "C:/Progra~1/Edition/vim/vim63/gvim.exe" --binary-opt=--servername=GVIM,--remote-tab-silent --fork=2 file1 If ran twice, this actually opens up two instances of gvim; it is as if the servername 'GVIM' is being stripped and ignored. How do you supply a servername to gvim --servername or a .vimrc to gvim -u using cyg-wrapper.sh? Furthermore, why is it that programs must be passed to cyg-wrapper.sh in the relatively obscure "mixed form?" For example, if I try cyg-wrapper.sh "/cygdrive/c/path/to/GVimPortable.exe" --binary-opt=--servername=GVIM,--remote-tab-silent --fork=2 I get "Invalid switch - "/cygdrive"." See also: getting-gvim-to-automatically-translate-a-cygwin-path alias-to-open-gvim-cream-version-from-cygwin-shell

  Read the article

• Installing SQLServer 2005 on Windows 7 64bit

  - by Mostafa

  Hi , It's 3 days I'm trying to install SqlServer 2005 under Windows 7 64 bit on my computer. First let me tell you what I've done and what I've got till now . 1-I Installed Windows 7 64 Bit on my computer 2-I tried to install SQl Server 2005 "Developer Edition" 2.1 But in "System Configuration Check" Page i recieved 2 warning , One for "IIS Feature Requirement" and another for "ASP.NET Version Registration Rquired" . 2.1.1 . I installed "Internet Information Services" from "Turn Windows features on or off" section in control panel 2.1.2 I Enabled reporting service 32 bit from "Inetpub= AdminScripts = adsutil.vbs" 2.2 At this stage There was no waring in System Configuration Check 3- So I installed SQl Server 2005 Developer Edition By all default settings 4- I installed Sql Server 2005 Service Pack 3 64 bit Now when when i run "Management Studio" There is no name in "Server name" section . I typed my Computer name Or "." and i got this Error : A network -related instance-specific error occurred while establishinga connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (Provider: Named Pipes Provider , error :40 - Could not open a connection to SQL Server ) ( Microsoft SQL Server , Error :2) . I googled some for this Error and some people said follow this instruction: Startsql server 2005Configuration toolsSql Server Surface Configuration AreaSurface Area Configuration for services and Connections But i got this Error : No SQl SErver 2005 Components were found on the specified computer . Either no components are installed , or you are not a administrator on this computer (SQLSAC) I'm really tired because of that , and i don't know what's wrong with this . Some more information : I have no additonal software on my computer , like Antivirus or Proxy I tried all step with "Standard Edition" either , but no difference My user is Administrator I tried more than 5 times all those steps including re-installing Windows 7 . Please help me , I'm losing all my hair

  Read the article

• How does the EFI partition work and can I boot an x86 OS with a bootx64.efi file?

  - by Ian

  I have a Thinkpad X230 laptop and I want to install Linux Mint Debian Edition along side Windows 7 on my GPT formatted SSD with the BIOS in UEFI mode. The problem is that I don't understand how EFI booting works. There seems to be an EFI partition involved with some folders and binary files in it. GRUB 2 seems to be able to make more folders in it (I followed this guide http://www.thinkwiki.org/wiki/UEFI_Firmware), but it appears that the only file that does anything is the bootx64.efi file in the /efi/boot folder of the EFI partition (I am not sure if this is always the case, but it appears to be the case for my laptop http://www.thinkwiki.org/wiki/Category:X220). Here is what I have been able to do: I can install Linux Mint Debian Edition x86 with the BIOS in BIOS mode on my SSD. I can then install grub-efi and follow the guide linked above. The problem is that I don't get a GRUB prompt when I switch the BIOS to UEFI mode. It just boots Windows. It appears that I can either boot from the SSD or something called "Windows Boot Manager". If I replace the bootx64.efi with the file created by GRUB, I can no longer boot directly from the SSD. Booting from "Windows Boot Manager" still works fine. I realize that the guide says to use x64 Linux, but Linux Mint Debian Edition x64 hangs during the install process. I am really confused. What should I do? Can anyone explain how the EFI boot partition works? Can a bootx64.efi boot an x86 OS? Should I just give up with using UEFI? I haven't been able to find very much useful information about using Debian based operating systems with UEFI. Thanks, Ian

  Read the article

• Active Directory FRS problems. 13508 error and other problems

  - by ITPIP

  I have 3 Domain Controllers. We will call them DC1, DC2 and DC3. DC3 and DC2 show Event ID 13508 in their FRS logs with no follow-up event(13509 I think) to say the error had been fixed. DC1's FRS log no matter what you do never shows any events besides FRS service stopped and started. DC1 holds the SYSVOL that needs to be replicated to the other DC's. The other DC's sysvol folders are empty. I have tried the burflag method of fixing this but I haven't had any luck. My procedure for that was to stop all FRS services on all DC's. Then set the burflag on DC1 to D4 and the other two DCs burflag to D2. Started FRS on DC1 and the only event's I see in DC1's FRS event logs are service stopped and service started messages. This fact is leading me to believe that something is wrong on FRS for DC1. I believe there should be events 13553 and 13516 in the FRS event logs after an authoritative sysvol restore. The other two DC's do not have anything in their SYSVOL, otherwise I would have made one of them the authoritative sysvol. DC1 is MS Server 2003 Enterprise Edition SP2 DC2 is MS Server 2003 Standard Edition SP1 DC3 is MS Server 2003 R2 Standard Edition SP2 I did not setup this domain originally but I am now the administrator of it, so I don't have a lot of background on why certain things may have been done in the past. My main goal is to try and fix these issues to get myself better prepared to decommision DC1 and add a DC running Server 2008 to my domain. Thanks.

  Read the article

• Confused about the Windows 7 Preinstallation Kit

  - by David Brown

  I build custom PCs and would like to use the Windows 7 Preinstallation Kit to make installation go a little quicker and customize the Windows image. However, since each PC is built to a particular customer's specifications, the hardware will rarely be the same. So, I would like to have a single answer file that will work for everything. I'm not sure if that's possible, however. What I mostly want to do for now is add my support information as well as pre-set anything that I would normally change after each installation completes. I have a Windows 7 Professional Upgrade DVD set (both 32-bit and 64-bit), but no OEM disks. I copied the Install.wim file to my local drive and opened it in the Windows System Image Manager, but it asks me to choose a catalog file specifically for each edition of Windows 7. Will this limit the answer file to whichever edition I choose? I would think choosing Starter would give me the most basic settings, which would apply to all other editions, but I'm not entirely sure of this. I don't intend to install any extra applications or drivers. I merely want to insert an OEM disk, my OPK USB drive, and have it work for whatever edition of Windows 7 I'm installing. If a large number of similarly-configured PCs need to be built, I'll go ahead and create a custom answer file in that case, but for a single machine order, that seems like overkill. In addition, do I need a separate answer file for 32-bit and 64-bit versions of Windows 7? Or will it work for both, even though I copied the Install.wim file from the 32-bit disk? Thanks!

  Read the article

• Google Desktop Search problems - unable to disable indexing and no index status page

  - by Howiecamp

  I've been running Google Desktop (I've used both the regular and Enterprise versions) without issues on my Windows 7 64-bit PC for a long time with no issues. I just paved my PC and reinstalled Google Desktop (regular edition). Initially, I want to use it only for the CTRL-CTRL launcher capability - I don't want it to do any indexing. So I unchecked all the items in the configuration dialog as well as excluded c:. Despite this, it is indexing all the content on my hard drive as well as Outlook email, etc. In my previous installations I had the same options set and they worked properly. The other problem I have is that when you right-click on the Google Desktop system tray icon, there used to be an option for "Index Status" which showed you the percentage complete the index creation process was, as well as an option to clear and rebuild the index. Those are no longer there. I uninstalled the regular edition and installed the Enterprise Edition, but same problems. Any ideas?

  Read the article

• mysqld-nt.exe exist in task list, but actually it's not running?

  - by PHP

  mysqld-nt.exe is showing in the task manager, but I cannot connect to it. I tried: telnet localhost 3306 And it fails to connect. So I restarted the server,and it's ok. This happens every day. Any ideas? EDIT Here is the error log(I didn't find anything abnormal though): 100122 10:11:16 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100122 10:11:16 InnoDB: Starting shutdown... 100122 10:11:18 InnoDB: Shutdown completed; log sequence number 0 22939338 100122 10:11:18 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100122 10:12:40 InnoDB: Started; log sequence number 0 22939338 100122 10:12:42 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100123 16:20:44 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100123 16:20:44 InnoDB: Starting shutdown... 100123 16:20:46 InnoDB: Shutdown completed; log sequence number 0 22939832 100123 16:20:46 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100123 16:22:09 InnoDB: Started; log sequence number 0 22939832 100123 16:22:11 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100125 9:18:59 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100125 9:18:59 InnoDB: Starting shutdown... 100125 9:19:00 InnoDB: Shutdown completed; log sequence number 0 22941001 100125 9:19:00 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100125 9:20:22 InnoDB: Started; log sequence number 0 22941001 100125 9:20:25 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL)

  Read the article

• Disk Error on Boot (Possible boot sector issue)

  - by Choco

  I own a 4-5 year old Dell Dimension E510 with Windows XP: Media Center Edition. I have 2 drives installed: C Drive: Windows XP: Media Center Edition G Drive: 2 partitions: Windows 7 (beta) Windows XP (professional) That is also the order they are connected. The C Drive is my primary drive. When I attempt to boot the computer, the bios loading screen appears normally; the progress bar moves and it's fine. The very next page, however, supposed to be a boot choice. When I installed Windows 7 onto the G Drive in context of the C drive it added a boot selector to the C drive's boot sequence. It gives me the option of booting Windows 7 or Windows XP: Media Center Edition. However, my problem is now this: After the bios screen I previously mentioned, instead of a boot selector, I receive the following error: A disk read error occurred. Press CTRL+ALT+DEL to restart. The drive is spinning up normally. I hear no odd noises/clicks/scraping coming from it, even after disabling the other drive to listen to it carefully. According to me, it's a boot sector issue. I have never experienced this before, but maybe during a recent shutdown, Windows XP: MCE errored out and ruined the boot sector. Dilemma! I don't have the Windows XP: MCE disc, because it was installed by the factory. I have accessed the hidden partition on the drive before (you hit a key combination on the bios screen and it comes up with an interface to fix your drive). However, I don't want to reformat the drive (which is what the interface gives me the option to do). I want to possibly fix the boot sector. How can I achieve that?

  Read the article

• MySQL password changed every other day in windows?

  - by PHP

  Every morning when I check server status,I will find MySQL's password is changed: mysql -uuser -ppassword will report ERROR 1045 (28000): Access denied for user 'user'@'localhost' (using password: YES) And then I restart server,and when it's up,MySQL will be back to normal. It has now become a routinely job. What can be the cause for this? How can I know what's exactly happening to MySQL? Here is the error log: 100122 10:11:16 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100122 10:11:16 InnoDB: Starting shutdown... 100122 10:11:18 InnoDB: Shutdown completed; log sequence number 0 22939338 100122 10:11:18 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100122 10:12:40 InnoDB: Started; log sequence number 0 22939338 100122 10:12:42 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100123 16:20:44 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100123 16:20:44 InnoDB: Starting shutdown... 100123 16:20:46 InnoDB: Shutdown completed; log sequence number 0 22939832 100123 16:20:46 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100123 16:22:09 InnoDB: Started; log sequence number 0 22939832 100123 16:22:11 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100125 9:18:59 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100125 9:18:59 InnoDB: Starting shutdown... 100125 9:19:00 InnoDB: Shutdown completed; log sequence number 0 22941001 100125 9:19:00 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100125 9:20:22 InnoDB: Started; log sequence number 0 22941001 100125 9:20:25 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL)

  Read the article

• vyatta Server Reboots by itself

  - by Fernando

  I have an issue regarding some hardware, maybe you can help me. First, I set up a Supermicro Superserver SYS-5016I-NTF with a Intel Xeon X3470 and 4 GB of Ram with a Hotlava Card Tambora 64G4 with Intel Chipset 82599EB and 4x10G SPF+ ports. Installed Vyatta community edition 6.3. I used it as router making BGP connections with 2 operators. No load at all, temp ranges normal. But the issue is that it reboots by itself in a ramdom way. Not very often, once every few days. But it is unacceptable for production purposes. So I try to test on different hardware, and installed Vyatta community edition 6.3 on a Dell PowerEdge 2950, with Xeon(R) E5345 @ 2.33GHz and 4 GB of Ram. Same Vyatta configuration as Supermicro Server. With same hotlava Card model ( I bought two of them ) Well I have reboots with this equipment as well. Same frecuency as above. I have checked syslog no strange logs until boot process starts to be logged. So it seems server reboot suddenly. I have installed latest driver for the chipset of the Hotlava card. Servers are placed in a datacenter with UPS So finally two things in common in both servers: Hotlava Card. Someone with issues with this card, or the chipset?? Could be it this card?? Vyatta 6.3 community edition. I don't thing is the problem. Is a regular Debian with packages to glue together different services. Or maybe is something I am missing. Andy ideas, suggestions?? Thank you very much... Fernando

  Read the article

• G4 server running slow

  - by Abby Kach

  I have HP proliant ML 350 servers. We have 8 remote locations where users connect and log on to our server through DYNDNS to access our company ERP's to conduct day to day work. The base of our company ERP's is oracle for which we have a separate server.Now the problem is day by day the load on the server is increasing and the speed is getting slower and slower and users are facing a lot of issues . so I are planning to implement Sonic wall VPN. I conducted a demo of sonic wall but it was slower than the current speed of dyndns. the configuration of my server is as follows :- Linux HP ProLiant 370 Intel Xenon 3.20 GHZ 150 GB (72 * 2) 3 GB Suse Omega HP ProLiant 370 Intel Xenon 3.20 GHZ 300GB (72.8 * 4) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Storage Box HP Storage Works 1400 Intel Xenon 2.00 GHZ 4 TB(1 TB * 4) Raid 5 2 GB Windows Server 2K8 Enterprise Edition Domain & Terminal HP ProLiant 350 Intel Xenon 3.20 GHZ 250 GB(72.8 * 3) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Can some one help me as to how can i speed up my network at remote locations and reduce the problems of speed etc..

  Read the article

• Active Directory FRS problems. 13508 error and other problems

  - by user59232

  I have 3 Domain Controllers. We will call them DC1, DC2 and DC3. DC3 and DC2 show Event ID 13508 in their FRS logs with no follow-up event(13509 I think) to say the error had been fixed. DC1's FRS log no matter what you do never shows any events besides FRS service stopped and started. DC1 holds the SYSVOL that needs to be replicated to the other DC's. The other DC's sysvol folders are empty. I have tried the burflag method of fixing this but I haven't had any luck. My procedure for that was to stop all FRS services on all DC's. Then set the burflag on DC1 to D4 and the other two DCs burflag to D2. Started FRS on DC1 and the only event's I see in DC1's FRS event logs are service stopped and service started messages. This fact is leading me to believe that something is wrong on FRS for DC1. I believe there should be events 13553 and 13516 in the FRS event logs after an authoritative sysvol restore. The other two DC's do not have anything in their SYSVOL, otherwise I would have made one of them the authoritative sysvol. DC1 is MS Server 2003 Enterprise Edition SP2 DC2 is MS Server 2003 Standard Edition SP1 DC3 is MS Server 2003 R2 Standard Edition SP2 I did not setup this domain originally but I am now the administrator of it, so I don't have a lot of background on why certain things may have been done in the past. My main goal is to try and fix these issues to get myself better prepared to decommision DC1 and add a DC running Server 2008 to my domain. Thanks.

  Read the article

• mysqld-nt.exe exist in task list, but actually it's not running?

  - by PHP

  mysqld-nt.exe is showing in the task manager, but I cannot connect to it. I tried: telnet localhost 3306 And it fails to connect. So I restarted the server,and it's ok. This happens every day. Any ideas? EDIT Here is the error log(I didn't find anything abnormal though): 100122 10:11:16 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100122 10:11:16 InnoDB: Starting shutdown... 100122 10:11:18 InnoDB: Shutdown completed; log sequence number 0 22939338 100122 10:11:18 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100122 10:12:40 InnoDB: Started; log sequence number 0 22939338 100122 10:12:42 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100123 16:20:44 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100123 16:20:44 InnoDB: Starting shutdown... 100123 16:20:46 InnoDB: Shutdown completed; log sequence number 0 22939832 100123 16:20:46 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100123 16:22:09 InnoDB: Started; log sequence number 0 22939832 100123 16:22:11 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100125 9:18:59 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100125 9:18:59 InnoDB: Starting shutdown... 100125 9:19:00 InnoDB: Shutdown completed; log sequence number 0 22941001 100125 9:19:00 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100125 9:20:22 InnoDB: Started; log sequence number 0 22941001 100125 9:20:25 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL)

  Read the article

• phablet-flash aborting while installing Ubuntu Touch on Nexus 4

  - by Till B

  I have a Nexus 4 with Android 4.3 installed and I want to flash it to Ubuntu Touch. My system is Ubuntu 12.04, running inside a virtual machine on Mac OS 10.5.8. To use the VM, I opened an NAT bridge and forwarded port 5037 for adb, I can see the Nexus with adb and e.g. use the adb shell into it. USB ports are also forwarded to the VM. I follow these instructions to the letter. My bootloader is unlocked, just as it was described in the instructions. Now I encounter different issues, when executing sudo phablet-flash ubuntu-system --no-backup. On the first run, it got stuck in this state: INFO:phablet-flash:Decompressing partitions/recovery.img from /home/till/Downloads/phablet-flash/imageupdates/pool/device-5ba3031cb0d6fc624848266edba781e3e821b6e1e8dd21105725f0ab26077d0a.tar.xz INFO:phablet-flash:Restarting device... wait INFO:phablet-flash:Restarting device... wait complete INFO:phablet-flash:Booting /tmp/tmpMSN8bm/partitions/recovery.img < waiting for device > downloading 'boot.img'... OKAY [ 1.772s] booting... OKAY [ 0.005s] finished. total time: 1.779s INFO:phablet-flash:Waiting for recovery image to boot The following happened: around the line "INFO:phablet-flash: Restarting...", it rebooted into the bootloader. The bootloader shows only for two seconds, then the screen goes off and the phone stays off. But I do notice, that the screen is not off - it is just black, but the background light is on. If I wait long enough, phablet-flash aborts with ERROR:phablet-flash:Wait for recovery expired On the second try, I wanted to manually start the bootloader and choose "Recovery mode". Pressing "volume down+power" at first did nothing. Releasing the buttons and then pressing them again brought me into the bootloder. After choosing "Recovery mode", phablet-flash continued and after a while aborted with the following output: INFO:phablet-flash:Wait for recovery image to boot complete INFO:phablet-flash:Clearing /data and /cache INFO:phablet-flash:Pushing /home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz to /cache/recovery/ failed to copy '/home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz' to '/cache/recovery/': Permission denied ERROR:phablet-flash:Command 'adb push /home/till/Downloads/phablet-flash/imageupdates/pool/ubuntu-2b5345658b58e55207c4a4e7b6b3d8cd4f3d9a3187d2448fc9020c884234bac0.tar.xz /cache/recovery/' returned non-zero exit status 1 Removing directory /tmp/tmpDnbz6N Removing directory /tmp/tmpth4L6w What can I do to properly flash my phone with Ubuntu Touch? I noticed that adb does not show the phone in recovery mode: Typing adb devices, when the Nexus 4 is in recovery mode, shows the serial number and the state device, where it should show recovery. Should the phone be rooted? This is not mentioned in the instructions.

  Read the article

• Find More Streaming TV Online with Clicker.tv

  - by DigitalGeekery

  Looking for a way to access more of your favorite TV Shows and other online entertainment? Today we’ll take a look at Clicker.tv which offers an awesome way to find tons of TV programs and movies. Clicker.tv Clicker.tv is an HTML5 web application that indexes both free and premium content from sources like Hulu, Netflix, Amazon, iTunes, and more. Some movies or episodes, such as those from Netflix and Amazon.com’s Video on Demand, will require viewers to have a membership, or pay a fee to access content. There is also a Clicker.tv app for Boxee.   Navigation Navigating in Clicker.tv is rather easy with your keyboard. Directional Keys: navigate up, down, left, and right. Enter: make a selection Backspace: return to previous screen Escape: return to the Clicker.tv home screen. Note: You can also navigate through Clicker.tv with your PC remote. Recommended Browsers Firefox 3.6 + Safari 4.0 + Internet Explorer 8 + Google Chrome Note: You’ll need the latest version of Flash installed to play the majority of content. Earlier versions of the above browsers may work, but for full keyboard functionality, stick with the recommendations. Using Clicker.tv The first time you go to Clicker.tv, (link below) you’ll be met with a welcome screen and some helpful hints. Click Enter when finished.   The Home screen feature Headliners, Trending Shows, and Trending Episodes. You can scroll through the different options and category links along the left side.   The Search link pulls up an onscreen keyboard so you can enter search terms with a remote as well as a keyboard. Type in your search terms and matching items are displayed on the screen.   You can also browse by a wide variety of categories. Select TV to browse only available TV programs. Or, browse only Movies in the movie category. There are also links for Web content and Music.   Creating an Account You can access all Clicker.tv content without an account, but a Clicker account allows users to create playlists and subscribe to shows and have them automatically added to their playlist. You’ll need to go to Clicker.com and create an account. You’ll find the link at the upper right of the page. Enter a username, password and email address. There also an option to link with Facebook, or you can simply Skip this step.   Go to Clicker.tv and sign in. You can manually type in your credentials or use the onscreen keyboard with your remote.   Settings If you’d prefer not to display content from premium sites or Netflix, you can remove them through the Settings. Toggle Amazon, iTunes and Netflix on or off.   Watching Episodes To watch an episode, select the image to begin playing from the default source, or select one of the other options. You can see in the example below that you can choose to watch the episode from Fox, Hulu, or Amazon Video on Demand.   Your episode will then launch and begin playing from your chosen source. If you choose a premium content source such as iTunes or Amazon’s VOD, you’ll be taken to the Amazon’s website or iTunes and prompted to purchase the content.   Playlists Once you’ve created an account and signed in, you can begin adding Shows to your playlist. Choose a series and select Add to Playlist.   You’ll see in the example below that Family Guy has been Added and the number 142 is shown next to the playlist icon to indicate that 142 episodes has been added to your playlist. Underneath the listings for each episode in your playlist you can mark as Watched, or Remove individual episodes.   You can also view the playlist or make any changes from the Clicker.com website. Click on “Playlist” on the top right of the Clicker.com site to access your playlists. You can select individual episodes from your playlists, remove them, or mark them as watched or unwatched. Clicker.TV and Boxee Boxee offers a Clicker.TV app that features a limited amount of the Clicker.TV content. You’ll find Clicker.TV located in the Boxee Apps Library. Select the Clicker App and then choose Start. From the Clicker App interface you can search or browse for available content. Select an episode you’d like to view… Then select play in the pop up window. You can also add it to your Boxee queue, share it, or add a shortcut, just as you can from other Boxee apps. When you click play your episode will launch and begin playing in Boxee. Conclusion Clicker.TV is currently still in Beta and has some limitations. Typical remotes won’t work completely in all external websites. So, you’ll still need a keyboard to be able to perform some operations such as switching to full screen mode. The Boxee app offers a more fully remote friendly environment, but unfortunately lacks a good portion of the Clicker.tv content. As with many content sites, availability of certain programming may be limited by your geographic location. Want to add Clicker.TV functionality to Windows Media Center? You can do so through the Boxee Integration for Windows 7 Media Center plug-in. Clicker.tv Clicker.com Similar Articles Productive Geek Tips Share Digital Media With Other Computers on a Home Network with Windows 7Stream Music and Video Over the Internet with Windows Media Player 12Listen to Online Radio with AntennaEnable Media Streaming in Windows Home Server to Windows Media PlayerNorton Internet Security 2010 [Review] TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos

  Read the article

• Unable to set background image using python (2.7.3), bash and gnome3

  - by malon

  #!/usr/bin/env python import os bashCommand = "gsettings set org.gnome.desktop.background picture-uri file:///home/malon/autowallpaperchanger/" + pic_name print bashCommand os.system(bashCommand) Print result: gsettings set org.gnome.desktop.background picture-uri file:///home/malon/autowallpaperchanger/wallpaper-1252048.jpg Copying and pasting the print result into a terminal makes the change successfully, so the command is correct, but os.system isn't processing the request correctly for some reason. In the full script (posted below), I use os.system for a different reason immediately before (wget) and that works fine. Thank you! Full script: http://pastebin.com/R90GTmBZ

  Read the article

• How to compile 'stygmorgan-0.29'?

  - by iwan

  I am trying to compile stygmorgan-0.29.tar.bz2 and got these messages: stygmorganui.cxx:7:28: fatal error: stygmicon128.xpm: No such file or directory compilation terminated. make[2]: *** [stygmorganui.o] Error 1 make[2]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make[1]: *** [all] Error 2 make[1]: Leaving directory `/home/papa/Downloads/stygmorgan-0.29/src' make: *** [all-recursive] Error 1 papa@papa-G31-M7-TE:~/Downloads/stygmorgan-0.29$

  Read the article

• get the path of moved directory/file (source path and destination path)

  - by Ghanshyam Rathod

  When one directory is moved to other destination path, then i want to log the entry of original source path and entry of the path where it moved. any command is already available ? or any other way of doing this task? Ex: D1 = /home/user/Documents/test D2 = /home/user/Documents/Data/test when i moved D1 directory to the destination path to D2 directory then i want to log, like "test" directory is moved from D1 to D2 path Thanks

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >