Search Results

Search found 18803 results on 753 pages for 'link'.

Page 129/753 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• Internet slow on one router only [the problem only in Ubuntu] [on hold]

  - by mrSuperEvening

  Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

  Read the article

• Why has my internet speed dropped down?

  - by Door Knob

  I recently switched to Ubuntu. I've been having a lot of internet troubles ever since. I used Windows 7 before. I've had trouble loading web pages, and it would take a solid minute or two to even start displaying anything. Why is this? How can I fix this? Details: Ubuntu 14.04 ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:2c:59:42 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 Memory:f7ae0000-f7b00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:785 errors:0 dropped:0 overruns:0 frame:0 TX packets:785 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:70511 (70.5 KB) TX bytes:70511 (70.5 KB) wlan0 Link encap:Ethernet HWaddr 14:da:e9:b0:9d:66 inet addr:192.168.2.12 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11979 errors:0 dropped:0 overruns:0 frame:0 TX packets:10503 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13659505 (13.6 MB) TX bytes:1449698 (1.4 MB) Here's a comparison: Speedtest on my phone: Speedtest on my PC: Taken about 30 seconds apart.

  Read the article

• How would one run a task sequence within a task sequence in SCCM 2012 SP1

  - by BigHomie

  A Shining Example: Inside all of my task sequences I have a group that installs driver packages conditionally based on computer model: And of course, this list does nothing but grow. The fact that it grows isn't a big deal, what is a big deal is that every time it changes I have to manually copy and paste those changes across every task sequence I have, which of course leaves huge room for human error. The same goes for other groups of tasks that are common across task sequences. Looking for a solution where I could centrally manage these tasks, be it link other task sequences to a group within another task sequence, or create a separate task sequence and link to that. I came across a solution by John Marcum (SCCM MVP) that mentioned this ability, but this was a while ago and I can't find the link to it anymore to see if it's even still being updated/maintained, but I'm looking for more of a free solution, or even using Powershell or the ConfigMgr SDK is fine with me, I'm no stranger to either. Update Getting close: http://msdn.microsoft.com/en-us/library/jj217869.aspx

  Read the article

• Apache virtual hosts - Resources on website not loaded when accessed from other hostname than localhost

  - by Christian Stadegaart

  Running virtual hosts on Mac OS X 10.6.8 running Apache 2.2.22. /etc/hosts is as follows: 127.0.0.1 localhost 3dweergave studio-12.fritz.box 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost Virtual hosts configuration: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot "/opt/local/www/3dweergave" ServerName 3dweergave ErrorLog "logs/3dweergave-error_log" CustomLog "logs/3dweergave-access_log" common <Directory "/opt/local/www/3dweergave"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost *:80> ServerName main </VirtualHost> This will output the following settings: *:80 is a NameVirtualHost default server 3dweergave (/opt/local/apache2/conf/extra/httpd-vhosts.conf:21) port 80 namevhost 3dweergave (/opt/local/apache2/conf/extra/httpd-vhosts.conf:21) port 80 namevhost main (/opt/local/apache2/conf/extra/httpd-vhosts.conf:34) I made 3dweergave the default server by putting it first in the list. This will cause all undefined virtual hosts' names to load 3dweergave, and thus http://localhost will point to 3dweergave. Of course, normally, the first in the list is the virtual host main and localhost will point to main, but for testing purposes I switched them. When I navigate to http://localhost, my CakePHP default homepage shows as expected: Screenshot 1 But when I navigate to http://3dweergave, my CakePHP default homepage doesn't show as expected. It looks like every relative link to resources are not accepted by the server: Screenshot 2 For example, the CSS isn't loaded. When I open the source and click on the link, it opens the CSS file in the browser without errors. But when I run FireBug while loading the webpage, it seems that the CSS file isn't retrieved. (<link rel="stylesheet" type="text/css" href="/css/cake.generic.css" />) How can I fix this unwanted behaviour?

  Read the article

• SEO and links content

  - by AntonAL

  For usability purposes, entire article thumbnail is wrapped to a link. <a href="/some_article"> <h2>Article title</h2> <div class="summary">Lorem ipsum dolor sit amet</div> </a> User needs to click on any place of a thumb and it will be redirected to article. Does this approach have some negative effect to SEO ? Another question: What is more valueable for Search Engine ? Just a link to article in articles list <a href="/article1">Article 1</a> <a href="/article2">Article 2</a> <a href="/article3">Article 3</a> Or h2, wrapped to link: <a href="/article1"><h2>Article 1</h2></a> <a href="/article2"><h2>Article 2</h2></a> <a href="/article3"><h2>Article 3</h2></a>

  Read the article

• Where can I configure wireless to be passed on to the Virtualbox guest?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• SEO & Multilingual: would be this a good practise?

  - by Younès

  I am currently making a bilingual website and I'd like to get nice SEO results of course. Here's my idea: The internal links would be composed of the "www" subdomain so that people can share links regardless of their language. Anyway, their language is determined by the HTTP_ACCEPT_LANGUAGE PHP variable. So, they would see http:// www.site.com/mydocument/123 in their adress bar and never see any links like "http:// fr.site.com/mydocument/123" or "http://en.site.com/mydocument/123" The user can always switch the page's language thanks to links in the footer. The switching language link would be : http:// fr.site.com/mydocument/123 , and clicking on it would change his language session and redirects the user to http:// www.site.com/mydocument/123 In case of a crawling bot: I read that if the HTTP_USER_LANGUAGE variable was missing then it's a crawling bot. So, in that case, we set the defaut language as English. Each page, as I mentionned earlier, has a link for another language: On the page: http:// www.site.com/document/1323, the link http:// fr.site.com/document/1323 can be seen by the bot and be crawled. What do you think about this practise ? Would I get good SEO results for each language ?

  Read the article

• Why are my backlinks not showing on google on this asp.net website with all I've done?

  - by Jason Weber

  I recently implemented many SEO techniques for a company on their asp.net website; in 6 months, we jumped from a PR1 to a PR3. But I'm having issues with google backlinking. Here are some of the things I've done: Not only did I set up their own Google+ page 6 months ago, I update it pretty much daily with links, pictures, etc., and I blog about it on my own personal Google+ page and post links, etc. ... They have their own Twitter, Facebook, YouTube, and all are updated almost daily. I've listed in as many quality, relevant directories as possible 6 months ago; I've avoided link farms. The site is solid SEO-wise. Key-phrase rich URLs, schema.org & rich snippets. No duplicate content ... www or non-www 301's, trailing slashes, etc. ... all taken care of. Probably a ton of other things, but basically, the site is all set, SEO-wise. Here's what's confounding: When I do a link:www.example.com in Bing/Yahoo, it shows many backlinks. When I do a link:www.example.com in google, it shows up 0 links. Or when I use a site-ranker like Web Site Rank Tool it's showing 0 backlinks from Google. Any suggestions would be appreciated!

  Read the article

• Wired Connection Problem

  - by Dave

  After upgrading to 12.04 my interent connection no longer works. More precisely it is really, really, slow, and occasionally will connect, but do so only for a few moments and then disappear again. I am on a Lenovo Workstation e20. Output of ifconfig: eth0 Link encap:Ethernet HWaddr 70:f3:95:00:64:3e inet addr:192.168.1.20 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::72f3:95ff:fe00:643e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7398 errors:0 dropped:74 overruns:0 frame:0 TX packets:6684 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5407828 (5.4 MB) TX bytes:854343 (854.3 KB) Interrupt:20 Memory:fb120000-fb140000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1587 errors:0 dropped:0 overruns:0 frame:0 TX packets:1587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:152089 (152.0 KB) TX bytes:152089 (152.0 KB) I am really at a loss for what to do. I am relatively new to Ubuntu, searched the other user questions and couldn't figure this out.

  Read the article

• How can I learn more about ADF?

  - by jhpierce -Oracle

  Look to the Oracle Technology Network for a wealth of information, tutorials, best practices and coding examples. The place to start is the Oracle Application Development Framework (ADF) web page. The Oracle ADF page has basic information and downloads for ADF, but the real wealth is in the links to other pages. One of the pages is the Oracle ADF Code Corner,  which is a blog-style column that provides hints, tips and coding examples for ADF developers. The content on this page ranges from easy to complex and often contains advanced programming concepts. The content is inspired by questions asked on the Oracle JDeveloper customer forum on OTN. The ADF Code Corner has many articles that will inspire your imagination and possibly solve your coding problem.How about the Oracle ADF Architecture Square link? The Oracle ADF Architecture Square focuses on architectural issues and developer guidelines for writing ADF software solutions. The goal is to give ADF developers an understanding of the necessary decisions for building a successful ADF application, to offer potential architectural blueprints to choose from when putting the ADF application together, and to provide potential ADF best practices to take back to your development team. The Oracle ADF Mobile link gives information on developing mobile applications for iOS and Android based applications. There are links to ADF Mobile Overview, ADF Mobile demos and ADF Mobile courses.The Sample ADF Applications link lists sample applications and other resources where you can find code samples for ADF. These are complete ADF applications that can be downloaded into JDeveloper and give you insight into coding an application.There are many more links found under the "Learn More" tab that can equip the developer with the knowledge they need to develop their applications. There are links to overview papers, technical resources, related topics and available training. The information you need IS just a click away.

  Read the article

• Sweden Windows Azure Group Meeting in November &amp; Fast with Windows Azure Competition

  - by Alan Smith

  SWAG November Meeting There will be a Sweden Windows Azure Group (SWAG) meeting in Stockholm on Monday 19th November. Chris Klug will be presenting a session on Windows Azure Mobile Services, and I will be presenting a session on Web Site Authentication with Social Identity Providers. Active Solution have been kid enough to host the event, and will be providing food and refreshments. The registration link is here: http://swag14.eventbrite.com If you would like to join SWAG the link is here: http://swagmembership.eventbrite.com Fast with Windows Azure Competition I’ve entered a 3 minute video of rendering a 3D animation using 256 Windows Azure worker roles in the “Fast with Windows Azure” competition. It’s the last week of voting this week, it would be great if you can check out the video and vote for it if you like it. I have not driven a car for about 15 years, so if I win you can expect a hilarious summery of the track day in Vegas. My preparation for the day would be to play Project Gotham Racing for a weekend, and watch a lot of Top Gear.   My video is “Rapid Massive On-Demand Scalability Makes Me Fast!”. The link is here: http://www.meetwindowsazure.com/fast/

  Read the article

• Listing Desktop Apps in the Windows 8 Store

  - by David Paquette

  So it looks like Microsoft will be allowing publishers to list their desktop apps in the Windows 8 Store.  As per the developer agreement: b. Desktop App Submission. You may submit an app description for one or more desktop apps to the Windows Store. Notwithstanding anything else in this agreement, you understand that Microsoft will not offer any desktop apps through the Store and only Windows Store apps are made available through the Windows Store. Microsoft may, but is not required to, list the desktop app in the Windows Store together with a link you provide, to a website where users can acquire the app. You are solely responsible and agree to maintain that website and provide an updated link to Microsoft if the url changes. Desktop apps are any apps built using APIs other than the APIs for Windows Store apps that run on Windows 8. As the agreement states, Microsoft will not distribute desktop apps through the store, but they will provide a link to a website where users can download your desktop app.  If nothing else, it is a great way to advertise your app.  Hopefully this doesn’t cause any confusion with consumers.  Will end users understand why some apps install automatically while others just send you to a website?

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• Create an array from mysql with column names and values [on hold]

  - by ScaZ

  i'm trying to create an array with PHP and MySQL, but i always get errors. The code i'm using function db_listar_usuarios(){ $link=db_connect(); $query = "select * from usuarios" or die("Problemas en el select: " . mysqli_error($link)); $result = $link->query($query); while($row = mysqli_fetch_assoc($result)) { $row['nombre'] . array(; foreach ($row as $col => $val) { $col => $val; } } } And what I want to create with this code is: array( 'john' => array('address' => 'st 123', 'age' => '25', 'surname' => 'doe'), 'ane' => array('address' => 'av 456', 'age'=> '32', 'surname' => 'smith'), ); To use then like something like this: private $contacts = db_listar_usuarios(); I use 2 files: functions.php and server.php server.php is a downloaded file example to do a REST API. Here are both of them. server.php - pastebin.com/5j54m1Mz functions.php - pastebin.com/N7jMhSBa Thank you in advance!

  Read the article

• What software can I use to create a video of following type?

  - by Bond

  Here is a video on this link http://www.youtube.com/watch?v=kSx873lOgIc&feature=player_embedded#at=62 Someone among my bosses wants to create some thing similar to the video on above link and has asked me what software can they use to do the same.The purpose is to create educational content only.Which can have the demonstrations (animations ) and audio also running in backend. I am not clear as what software can be used for this on Linux or Windows. I have users which use Windows and Linux both. I have used video editing on Mac using Final Cut Pro but the video on the above link is not some thing which can be achieved with FCP.(Or may be I am not aware) I am looking solution for 1) Linux users 2) Windows users In case of Linux it is Ubuntu for some users and Fedora for some others. I am a Linux guy so I am specifically posting this question in terms of Ubuntu but I also need suggestions for Windows type of users.I have no clue of such video animations at all.

  Read the article

• Do I need to conver the older Access Database, and, if so, how?

  - by octopusgrabbus

  I have an Access 2003 database. When I click on a pivot table, I get this message MS Access There isn't enough memory to complete the Automation object operation on the worksheet object. There is a lot of discussion concerning this message. Here is one link. http://community.spiceworks.com/topic/113228-access-2003-file-pivot-table-issue-when-opening-in-access-2010 But this particular link's explanation doesn't really go into fixing the problem in general, like fixing the pivot tables and getting things all nicely back together in the original Access database. That's why I am also interested in converting the database to 2010 format if that is possible. Are there instructions -- I cannot currently find them and would very much appreciate a link -- on dealing with this problem in a nice stepwise fashion?

  Read the article

• How do I copy hyperlink only (and not text) to another cell?

  - by OfficeLackey

  I have a spreadsheet where column A displays names. There are a few hundred names and each has a different hyperlink (which links to that person's web page). I want to transfer those hyperlinks across to a different column which has different text in and no hyperlinks. Not every cell in column A has a hyperlink. There are groups of cells merged together, so A2:A7 has one link, A8:A13 the next, A9:10 the next (i.e. number of cells merged is not uniform). e.g. where A2:A7 reads "Bob" and links to www.bob.com, I want I2:I7, which reads, "Smith," and does not link to anything, to link to www.bob.com. I want to do this repeatedly, copying links from A2:A579 into I2:I579. The information is copied from a table within a web page, and that is where the hyperlinks come from.

  Read the article

• How to make ip Address static (eth0)

  - by Jordan Angelucci

  I'm having a really hard time configuring ubuntu 13.04 to have a static ip address. I have tried multiple solutions but everytime I reboot (can't do the network reset command because ubuntu freezes) I end up with no connection. Here is what I get when i type ifconfig into the terminal: eth0 Link encap:Ethernet HWaddr 10:bf:48:bc:07:cb inet addr:192.168.0.8 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::12bf:48ff:febc:7cb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1763067 errors:0 dropped:0 overruns:0 frame:0 TX packets:1024326 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2284491220 (2.2 GB) TX bytes:136809317 (136.8 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1840 errors:0 dropped:0 overruns:0 frame:0 TX packets:1840 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:185688 (185.6 KB) TX bytes:185688 (185.6 KB) I have also tried this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.160 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 24.222.0.94 dns-nameservers 24.222.0.95 If anyone could help me it would be very much appreciated.

  Read the article

• vmware player - ubuntu can resolve hostname but ping fails

  - by recursive_acronym

  Using VMware players on Windows 7 with a Ubuntu 10.04 guest. When I ping it resolves the ip address but the ping fails. Hopefully this is a local issue as I don't have access to any of the network equipment (routers, etc). vmware tools is installed. Is there any other information I can provide to help resolve this? eth0 Link encap:Ethernet HWaddr 00:0c:29:83:4f:c0 inet addr:192.168.163.129 Bcast:192.168.163.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe83:4fc0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:50006 (50.0 KB) TX bytes:16701 (16.7 KB) Interrupt:19 Base address:0x2024 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)

  Read the article

• How to use CLEAR USB WiMax in Ubuntu (host) and Windows XP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for Linux as yet. I've installed Windows XP as guest in Ubuntu and the version I'm using is 3.2.2. USB is connecting fine in Windows XP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• Google Music Player doesn't work

  - by EricoPF

  I'm trying to log in on Google Music Player application but doesn't work. I get the message below: Login Failed Could not identify your computer. Learn More On Google Help it says that it doesn't run on virtual machines, which is not my case, but I have a virtualbox installed though, and it says some people get to work if they disable their bridge network. The thing is I don't have any bridge interface, even if I remove all virtualbox modules I still get this message. This is my ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:15374 errors:0 dropped:0 overruns:0 frame:0 TX packets:15374 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1455889 (1.4 MB) TX bytes:1455889 (1.4 MB) wlan0 Link encap:Ethernet HWaddr 94:db:c9:b2:1b:d7 inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::96db:c9ff:feb2:1bd7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:828467 errors:0 dropped:0 overruns:0 frame:0 TX packets:568040 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1086663025 (1.0 GB) TX bytes:72984931 (72.9 MB) Any ideias ? Thanks guys! Cheers.

  Read the article

• Unable to ping between subnets and out to internet

  - by battlemidget

  My setup is Modem - Linksys router - Laptop with 2 devices (wlan0/eth0) - desktop machine Router is 192.168.1.1 gateway to the internet Laptop wlan0 is 192.168.1.4 with a gw of 192.168.1.1 Laptop eth0 is 192.168.2.254 which acts as a second gateway desktop is 192.168.2.100 On laptop i've setup ip_forward to 1, and have inserted 2 iptables rules -A FORWARD -i eth0 -o wlan0 -j ACCEPT -A FORWARD -i wlan0 -o eth0 -j ACCEPT The laptop can ping outside the network (i,e, yahoo.com) it can not ping 192.168.2.100. The desktop can ping 192.168.2.254 but nothing outside the network or 192.168.1.0 subnet. On laptop ip route show lists: 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.4 127.0.0.0/8 dev lo scope link default via 192.168.1.1 dev wlan0 What am I missing to make my desktop go through the laptop in order to access the router which provides access to the internet? Thanks

  Read the article

• Linux, GNU GCC, ld, version scripts and the ELF binary format -- How does it work? [closed]

  - by themoondothshine

  I'm trying to learn more about library versioning in Linux and how to put it all to work. Here's the context: I have two versions of a dynamic library which expose the same set of interfaces, say libsome1.so and libsome2.so. An application is linked against libsome1.so. This application uses libdl.so to dynamically load another module, say libmagic.so. Now libmagic.so is linked against libsome2.so. Obviously, without using linker scripts to hide symbols in libmagic.so, at run-time all calls to interfaces in libsome2.so are resolved to libsome1.so. This can be confirmed by checking the value returned by libVersion() against the value of the macro LIB_VERSION. So I try next to compile and link libmagic.so with a linker script which hides all symbols except 3 which are defined in libmagic.so and are exported by it. This works... Or at least libVersion() and LIB_VERSION values match (and it reports version 2 not 1). However, when some data structures are serialized to disk, I noticed some corruption. In the application's directory if I delete libsome1.so and create a soft link in its place to point to libsome2.so, everything works as expected and the same corruption does not happen. I can't help but think that this may be caused due to some conflict in the run-time linker's resolution of symbols. I've tried many things, like trying to link libsome2.so so that all symbols are alised to symbol@@VER_2 (which I am still confused about because the command nm -CD libsome2.so still lists symbols as symbol and not symbol@@VER_2), but nothing seems to work. What am I doing wrong?

  Read the article

• Open mail-links with gmail in Chrome 9

  - by moose

  it happens quite often, that I click a link over a persons name, just to see that it launches the default mail client of my system. I thought it would be a normal link, but it was a "mailto:"-link. I would like Chrome to start gmail, not my default email client. For Firefox, I had only to paste this in the URL-Bar: javascript:window.navigator.registerProtocolHandler("mailto","https://mail.google.com/mail/?extsrc=mailto&url=%s","GMail") Unfortunately, it doesn't work in Chrome 9. I have found this tutorial for Ubuntu, but I would like a solution in Chome. If it is only in Chrome, I can sync the settings. (So How do I make mailto: links open gmail in Ubuntu? doesn't fit) http://www.google.com/support/forum/p/Chrome/thread?tid=2aad08042607a4eb&hl=en could be related to my problem, but there is no answer. Gnome: $ gnome-default-applications-properties set Email-Client to gnome-open https://mail.google.com/mail/?extsrc=mailto&url=%s

  Read the article

• Workaround broken sudo?

  - by perreal

  I managed to break sudo by deleting the libc.so.6 sym-link in /lib. I copied the actual file and created a symbolic link with the same name under my home directory by using LD_PRELOAD=/lib/libc-2.11.3.so. At this point, all binaries linking libc are working through preload except sudo. For sudo, I need to write (and don't know why): $ /lib/ld-linux-x86-64.so.2 --library-path . /usr/bin/sudo but this gives me: $ sudo: must be setuid root Checking the permissions: $ ls -l /usr/bin/sudo $ -rwsr-xr-x 2 root root 166120 So the setuid bit is actually set. Question: I need to create a symbolic link named /lib/libc.so.6 through my active ssh connection without using sudo, or, make sudo work somehow. I don't have the root password and I can't connect through ssh anymore. Is there any other way I can get authorization?

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >