Search Results

Search found 6523 results on 261 pages for 'route planning'.

Page 129/261 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• DNS error only in IE

  - by Le_Quack

  Our Intranet page has stopped working on some machines/some user accounts. The error I am getting points to a DNS issue but If I ping the site from the command line the it responds fine. The error I'm gettting on IE is Error: The web filter could not find the address for the requested site Why are you seeing this: The system is unable too determine the IP address of intranet.example.com I'm not quite sure why it mentions the web filter as there is a proxy exception for the intranet page and if I run a trace route it doesn't go via the web proxy (filtering system). Finally it isn't affecting everyone, just random users, also it doesn't affect the random users on all the client machines they use. I have one user where it happens on any client they log onto where most its just certian clients. It's even "fixed" itself for a few peoples. EDIT: hey Mikey thanks for the fast response. Proxies are correct and automatic configuration is off (both via GPO)

  Read the article

• ECMP Load Balancing in JUNOS

  - by SpacemanSpiff

  I'm trying to figure out how to use ECMP load balancing in JUNOS. I know this isn't the best way to load balance, but its quick and dirty and gets done what I need to. In ScreenOS this was pretty easy. Device: SRX220 JunOS: 10.3R2.11 Here's what I've got so far: routing-options { static { route 0.0.0.0/0 { next-hop [ 1.1.1.1 1.1.1.2 ]; metric 10; } } maximum-paths 2; Will that do it? Tom

  Read the article

• How can I recreate root dnsNode objects and their RootDNSServers folder in AD after they are deleted?

  - by TonyD

  A few days ago I was trying to permanently remove root hints from my DNS server. After much ado, I decided to go a different route and am now trying to put everything back as it was. During the original process, I opened ADUC, clicked ViewAdvanced Features, and then browsed to System MicrosoftDNS and deleted the folder RootDNSServers. Now in ADUC, I cannot create a folder here to replace the one I deleted. I can run adsiedit and load DomainDNSZones for my domain. Under there, I see MicrosoftDNS, RootDNSServers, with all of the objects still inside of it. Is there a way for me to undo what I did? Can I recreate these objects in ADUC? Can I do something else to cause them to show back up there? Thanks!

  Read the article

• Testing Tomcat with Virtual Hosts

  - by Marty Pitt

  I'm trying to test Tomcat virtual hosts on my dev machine (windows 7/Tomcat 6). I'd like to have requests for localhost, test1.localhost and test2.localhost all route through to the same tomcat instance. I've edited my hosts file to look as follows: 127.0.0.1 localhost ::1 localhost 127.0.0.1 test1.localhost 127.0.0.1 test2.localhost And added modified the Engine in server.xml as follows: <Engine defaultHost="localhost" name="Catalina"> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase" /> <Host appBase="webapps" autoDeploy="true" name="localhost" unpackWARs="true" xmlNamespaceAware="false" xmlValidation="false"> <Alias>test1.localhost</Alias> <Alias>test2.localhost</Alias> </Host> </Engine> However, I'm getting a 404 when hitting test1.localhost:8080/myWebApp, although localhost:8080/myWebApp works fine. I can ping test1.localhost fine. What have I missed?

  Read the article

• Getting MSExchange transport Error on Server 2003 SP2

  - by Scott

  I am getting the following Error messages and do not know how to fix it. Event Type: Error Event Source: MSExchangeTransport Event Category: (8) Event ID: 3017 Date: 4/29/2010 Time: 1:21:12 PM User: N/A Computer: NETSRV Description: A non-delivery report with a status code of 5.3.5 was generated for recipient rfc822;[email protected] (Message-ID <19104335.51321272561635734.JavaMail.SYSTEM@PARROT). Causes: A looping condition was detected. (The server is configured to route mail back to itself). If you have multiple SMTP Virtual Servers configured on your Exchange server, make sure they are defined by a unique incoming port and that the outgoing SMTP port configuration is valid to avoid looping between local virtual servers. Thanks for any help you can provide.

  Read the article

• how can I stop my sonicwall TZ-210 (SonicOS Enhanced 5.5.1.0-5o) from responding to arp queries on the wan subnet?

  - by IsaacB

  My sonicwall TZ-210 is answering arp queries on the wan subnet (which my isp doesn't like), basically mapping all the wan ips to its own mac address, causing network havoc since it is not set to route those back to the main isp gateway. How the heck can I turn this behavior off? I have already entered in all wan subnet ips in the static arp cache and left them 'unpublished' which I presumed would mean that it did not bother answering arp queries for them. Apparently it did not do the trick. Arp queries are still being answered unfortunately. What can I do? Any suggestions?

  Read the article

• mod_jk fails to detect error state because JBoss gives 404, not 500

  - by Ilya Sher

  Configuration: Apache + mod_jk, several workers on other machines (load balancing). When JBoss fails to deploy an application for example because of failed connection to the database, requests to /myapp/somepage generate 404. How do I configure JBoss to return 500 for everything under /myapp when the application failed to deploy? Additional info: Since 404 is not an "error state" code, mod_jk does not mark the worker as failed and continues to route the traffic there. Since there might be valid requests to this application also generating 404, I can not configure mod_jk to treat 404 as an "error state"

  Read the article

• In Varnish stats, what does "Backend conn. reuses" and "recycles" mean?

  - by electblake

  I have varnish installed and I think it's working properly (not sure if it matters but I am using iptables reroute method to route ports incoming:80 > varnish:8080 > apache:80 Anyway, In varnishstat I see a pretty high Hitrate average (60-80%) which I am working on but I am unclear at what all of the stats presented by varnishstat Specifically the following Backend stats: 380 0.00 0.26 Backend conn. success 10122 15.00 6.85 Backend conn. reuses 267 0.00 0.18 Backend conn. was closed 10391 15.00 7.04 Backend conn. recycles I've read a blog post called "Varnishstat for dummies" which outlines a lot of details of varnishstat (I recommend it for beginners) but it does not go over these Backend stats. Feel free to explain here or link to a resource I've missed :) thanks!

  Read the article

• IIS 7 Request routing

  - by Abraham Durairaj

  Not sure the title is right. I have my site configured in IIS7 and I have another partner site which runs on a different port eg. http:// localhost:1234 /mysite. Can I have my parent site to have a virtual site http:// localhost /mysite to route requests to the partner site http://localhost:1234 /mysite. I should not redirect but I should basically proxy the requests. Any help here is appreciable. Thanks in advance.

  Read the article

• Natively boot Virtualbox Image

  - by isync

  I am faced with a Windows hardware/software problem left over from another person. It's on me to resolve. It's a mission critical setup. The situation is: I've got a physical server machine with: -Disk C:\ (one disk) containing a basic install of Windows Server 2008 R2, formerly Win Vista Pro, now gone. -Disk D:\ (software Raid) containing a VirtualBox disk image of a configured Windows Server 2008 R2 running SQL Server R2 among others. What shall I do now? Migrate all the stuff from the configured VM to the basic but natively installed C:\ Windows Server 2008 R2 (with the possibility of breaking stuff)? Or, Setting up the machine to "natively boot" the VM with the help of bcdedit.exe (something I've read about, what I've never done, what I don't know of if it works, if it hits performance, or if it is stable for production) For me, being old skool, I am in the process of de-virtualising everything (option 1). But I'd be happy if someone suggests I am ok to go down the "natively boot" route.

  Read the article

• Automatically connect to VPN when initiating RDP Remote Desktop connection and then disconnect VPN when done

  - by Josh Newman

  I know I can create a batch file to initiate a VPN connection followed by an RDP session, however I want to know if it's possible (in Windows 7 and ideally Windows XP as well) to have the VPN connection tied to the RDP session status. Scenario: user has to VPN first in order to be able to RDP. Ideally user would click one icon (batch file?) to initiate VPN connection and load RDP session. When they close the RDP session I want the VPN to then automatically disconnect so they don't accidentally route their subsequent non-RDP browsing + Internet activity through the VPN.

  Read the article

• How can I specify nameserver's port number in osx? [duplicate]

  - by Cofyc

  This question already has an answer here: How is DNS lookup configured for OSX Mountain Lion? 2 answers In resolver manual, it said: The address may optionally have a trailing dot followed by a port number. For example, 10.0.0.17.55 specifies that the nameserver at 10.0.0.17 uses port 55. But it doesn't work, in /etc/resolv.conf or files under /etc/resolver/. 208.67.222.222.5353 Can I specify non-default port number for nameserver in osx? Update: osx don't use /etc/resolve.conf, but use files under /etc/resolver/. I have wrote a file dev with content '127.0.0.1' to route all dns queries for *.dev domains to a local dns server (127.0.0.). But I cannot specify dns server's port here. (It uses 53 anyway) Maybe there is no way to specify port number under osx?

  Read the article

• Switch computer off automatically when the internet is disconnected

  - by Vin

  Is there any free software that will detect the status of internet and shutdown the system when the internet disconnects? Or (more generally) can something run a task when the internet disconnects, and I can route it to shutdown the machine? I am downloading things overnight. But my problem is that sometimes the internet connection will be disconnected in the middle of the night, so there is no point in keeping the system running the rest of the night. So I need to avoid this problem by detecting the net connectivity.

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• Need assistance setting up Linux Router with 2 public lans

  - by user195407

  I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

  Read the article

• Multiple External IP Ranges on a Juniper SSG5

  - by Sam

  I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

  Read the article

• Node.js server crashes , Database operations halfway?

  - by Ranadeep

  I have a node.js app with mongodb backend going to production in a week and i have few doubts on how to handle app crashes and restart . Say i have a simple route /followUser in which i have 2 database operations /followUser ----->Update User1 Document.followers = User2 ----->Update User2 Document.followers = User1 ----->Some other mongodb(via mongoose)operation What happens if there is a server crash(due to power failure or maybe the remote mongodb server is down ) like this scenario : ----->Update User1 Document.followers = User2 SERVER CRASHED , FOREVER RESTARTS NODE What happens to these operations below ? The system is now in inconsistent state and i may have error everytime i ask for User2 followers ----->Update User2 Document.followers = User1 ----->Some other mongodb(via mongoose)operation Also please recommend good logging and restart/monitor modules for apps running in linux

  Read the article

• Why Mac cannot connect to Iphone?

  - by martin08

  I couldn't always ssh to my iPhone from my Mac. They're both on the same wifi network but sometimes the connection is established, sometimes it failed. From my Mac: $ ssh [email protected] ssh: connect to host 192.168.0.102 port 22: Operation timed out $ ping 192.168.0.102 PING 192.168.0.102 (192.168.0.102): 56 data bytes ping: sendto: No route to host ping: sendto: Host is down ping: sendto: Host is down I enabled SSH on the phone and am sure it can load webpages. So what might be a reason why they cannot connect? Thanks

  Read the article

• What is the best MTA setup for a home/laptop computer (*not* server)?

  - by thomasrutter

  Hello, What is a good MTA (e.g. Postfix or something else) setup for a home computer behind a NAT, or a laptop that is not always online? I've read a lot of Postfix tutorials on how to set it up this way or that, but they are usually geared towards computers that are servers ie they have a static IP have a domain name are always connected to the same network My requirements are, I guess: Ability to redirect mail for local users to another server of my choosing. No listening for incoming SMTP connections - outgoing only Ability to route outgoing mail via an external SMTP server with authentication (and perhaps encryption) If not Postfix, I need an MTA which can queue up mails in case it temporarily has no internet connection.

  Read the article

• ISP Load Balancing with ISA 2006

  - by Bill Best

  I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

  Read the article

• How to install PHP, Pear, PECL, and APC with Homebrew on Mac OS X?

  - by Andrew

  I'm trying to install APC for PHP 5.3 in the easiest way possible. I love Homebrew so I started down that route. I was able to install PHP 5.3.6 with this command: brew install https://github.com/adamv/homebrew-alt/raw/master/duplicates/php.rb --with-mysql I think this is supposed to install PHP, Pear, and PECL. It seems to install these just fine. Now when I try to install APC: $ pecl install apc downloading APC-3.1.9.tgz ... Starting to download APC-3.1.9.tgz (155,540 bytes) .................................done: 155,540 bytes Warning: require_once(Archive/Tar.php): failed to open stream: No such file or directory in PackageFile.php on line 305 Warning: require_once(Archive/Tar.php): failed to open stream: No such file or directory in /usr/local/Cellar/php/5.3.6/lib/php/PEAR/PackageFile.php on line 305 Fatal error: require_once(): Failed opening required 'Archive/Tar.php' (include_path='/usr/local/Cellar/php/5.3.6/lib/php') in /usr/local/Cellar/php/5.3.6/lib/php/PEAR/PackageFile.php on line 305 How can I fix this?

  Read the article

• firehol (firewall) with bridge: how to filter

  - by Leon

  I have two interfaces: eth0 (public address) and lxcbr0 with 10.0.3.1. I have a LXC guest running with ip 10.0.3.10 This is my firehol config: version 5 trusted_ips=`/usr/local/bin/strip_comments /etc/firehol/trusted_ips` trusted_servers=`/usr/local/bin/strip_comments /etc/firehol/trusted_servers` blacklist full `/usr/local/bin/strip_comments /etc/firehol/blacklist` interface lxcbr0 virtual policy return server "dhcp dns" accept router virtual2internet inface lxcbr0 outface eth0 masquerade route all accept interface any world protection strong #Outgoing these protocols are allowed to everywhere client "smtp pop3 dns ntp mysql icmp" accept #These (incoming) services are available to everyone server "http https smtp ftp imap imaps pop3 pop3s passiveftp" accept #Outgoing, these protocols are only allowed to known servers client "http https webcache ftp ssh pyzor razor" accept dst "${trusted_servers}" On my host I can connect only to "trusted servers" on port 80. In my guest I can connect to port 80 on every host. I assumed that firehol would block that. Is there something I can add/change so that my guest(s) inherit the rules of the eth0 interface?

  Read the article

• How do you implement NAT-T passthrough on a Juniper SRX series Firewall?

  - by Chris

  We have 3 juniper SRX-100 firewalls, they are configured like so: FW1 - FW2 - INTERNET - FW3 We would like to create an IPSEC tunnel between FW3 and FW1 passing through FW2 preferably using NAT-T. Is this possible? FW1 and FW2 have some strict access rules only allowing 1 port connected (it's a DMZ with a server in) so we can't just create a route based vpn between FW1 and FW2 to forward the traffic (otherwise all traffic will be forwarded) We know the tunnel is fine because we have managed to test it between FW1 and FW3 (without FW2 in the middle) so we know that the issue is to do with the 'passthrough' on FW2. Essentially, the question is - What options do we need to select on FW2 to enable it to pass through the IPSEC traffic straight to FW1? Many thanks in advance

  Read the article

• Can't connect to wireless-n in dual mode.

  - by Tyllyn

  I recently purchased a Acer Aspire Revo AR3610-U9022. This little nettop uses a Atheros AR5B91 Wireless Network Adapter. I also have a Netgear RangeMax NEXT Wireless Route (model WNDR3300). I have been using this router in dual mode (11G and 11N) on my normal desktop without a problem (Mode: Up to 270Mbps at 5GHz & 54Mbps at 2.4 GHz), but doing this, my Revo won't detect the 11N network as being around... my desktop still does, but the Revo, nope... just the 11G. However, when I switch my router over to just "Up to 270Mbps at 2.4GHz", it kills the 11G entirely, but the Revo recognizes the 11N network. I'm a programmer by trade, and this hardware-y stuff confuses me more than it should. Is there any way that I could set this stuff up so my Revo can connect to the 11N part of my router, but keep the 11G around? :) Thanks!

  Read the article

• Splitting Ethernet cable

  - by Nathan

  I am looking for the best way to network my small business. I have an office where my router/modem are located, and then 2 more computers in another room. I can route Ethernet to this room with about 75 ft of cabling, and I would like to do this because my computers on Ethernet are getting 3x the speed as computers on wireless. Is there any way I can use just one Ethernet cable to span the 75 feet, and then maybe 2 smaller ones to go to the two computers from there? If there's a simple way to do this, maybe with a connector that would be ideal, as opposed to buying over 150 ft of cabling. Thanks!

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >