Search Results

Search found 744 results on 30 pages for 'metric'.

Page 13/30 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • Unable to ping inside or outside network with default gateway 0.0.0.0

    - by agentroadkill
    I've been around here before and I could usually piece together everything to more or less get myself up and running, but this time I'm truly stumped. I'm trying to connect my new 14.04 install to a network, and I'm forced to be behind my college's router. Now I've tested the vary cable that is right now plugged into my Ubuntu box on a Windows, Mac OS X, and even my friend's Ubuntu 14.04 box, and they all connect no problem. I've been trying to track this down for about two days, but every time I get close to it, the bug jumps to some other piece of my connection. Anyway, as it sits ifconfig -a gives: eth2 Lninkencap:Ethernet HWaddr:00:1f:bc:08:31:1d inet addr:10.32.51.51 Bcast:10.32.51.155 Mask: 255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 RX bytes:0 TX bytes:0 as well as the local loopback, but I'm assuming that is not an issue here. sudo dhclient -v eth2 returns: Listening on LPF/<hardware address of my integrated NIC, above> Sending on <same> Sending on Socket/fallback DHCPREQUEST of 10.32.51.51 on eth2 to 255.255.255.255 port 67 (xid=0x6f4a66ba) <two more lines of same> DHCPDISCOVER on eth2 to 255.255.255.255 port 67 interval 3 (xid=0x156f9fb4) <many more of above with varying intervals> No DHCPOFFERS received. Trying recorded lease 10.32.51.51 RTNETLINK answers: File exists bound: renewal in <large number> seconds If I then try ping 8.8.8.8, I get: connect: Network is unreachable /etc/resolv.conf only contains the two lines telling you not to edit it, while /etc/network/interfaces only has the loopback interface block in it. I've tried commenting out the "option rfc3442" line in /etc/dhcp/dhclient.conf which seemed to fix this issue for many people, as well as adding the line send vendor-class-indentifier "MSFT5.0" to dhclient.conf as well to tell the router I'm a windows box, in case they don't like Linux. Finally, route -n reveals: Destination Gateway Genmask Flags Metric Ref Use Iface 10.32.51.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 I would like to apologize in advance for the doubtless butchered text alignment, but I'm obviously typing this all by hand, reading from the terminal as I type commands. I'm hoping this is an interesting problem, and not something I blithely stumbled past in my (apparent) over-confidence. TIA! Quick addendum before posting: The activity light on the ethernet port are lit and one blinks during boot, but they rarely (and seemingly randomly) do so afterwards (both are dark) even while running dhclient in the foreground. When I had the Ubuntu box tethered to my MacBook earlier, I got what looked like a normal power/uplink blinking pattern, but was unable to ping one from the other.

    Read the article

  • Free Webinar: Monitoring your business, not just your servers – Getting the most out of SQL Monitor

    Wednesday July 25 2012, 6:00pm BST: Learn how you can use SQL Monitor to gather information and alert on extra performance data for your servers and applications, making this tool vital for keeping an eye on your business. In this free webinar David Bick, Product Manager at Red Gate, will give you an overview of SQL Monitor including the new custom metric functionality in v3. Repeatable deployment without fear of data lossUse your version control system with the SSMS plug-in SQL Source Control and SQL Compare for accurate deployments without the worry. Find out more.

    Read the article

  • Ubuntu 12.04 - PPTP VPN is the only Internet Access

    - by user212553
    I know this has been covered. I've read dozens of posts but still have questions. I have a work server whose traffic should never leave my house without encryption. The VPN is PPTP. Currently I have a cron job that checks the status of the ppp0 adapter each minute. If the connection drops, which it does fairly often, it shuts key components down. It's fairly easy to restart PPTP with "nmcli con up id 'myVPNServer'" but there's no assurance it will reconnect and I need a better way to stop traffic (other than killing apps) when ppp0 is down. The two options I've seen discussed are the firewall (UFW, Firestarter, IPTables) or the route tables. I could be easily swayed to consider the firewall option but I focused on the route tables since no new function needs to be started. My questions involve the way the route tables change and then specifics on rules. When I start the PPTP VPN the route tables change. That suggests that if the VPN drops, the table will change back, defeating my stated intent of preventing external traffic. How can I make "sticky" changes to the route table that will persist even if the VPN connection drops? Perhaps the check boxes "Ignore automatically obtained routes" or "Use this connection only for resources on it's network" (which are part of the VPN configuration options)? It would seem that, if I can force the active VPN route table to stay in effect, even when the VPN drops, that this will effectively kill any external traffic should the VPN drop. This will give me the latitude to run a routine to restart the VPN from the command line (assuming the route table rules don't prevent me re-establishing the connection). My route table, with the VPN active is (ip route list): Any comments on what 10.10.1.1 is? $ ip route list default dev ppp0 proto static 10.10.1.1 dev ppp0 proto kernel scope link src 10.10.1.11 VPN_Server_IP_Address via 192.168.1.1 dev eth0 proto static VPN_Server_IP_Address via 192.168.1.1 dev eth0 src 192.168.1.60 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.60 metric 1

    Read the article

  • Properly Analyze the Value of the Cloud

    Most analyses of the benefits of cloud computing are based on unrealistic total cost of ownership (TCO), return on investment (ROI), and capex/opex calculations. To fully understand the potential benefits of cloud computing, a new metric is required.

    Read the article

  • Force Windows Local Subnet Traffic through a Gateway

    - by Beerey
    Hi all, We are attempting to route all traffic from a certain machine to a gateway. This works ok for traffic destined for subnets outside of the machine's subnet. However, traffic to machines in the same subnet as the source machine goes through an On-Link gateway in Windows. This means that the default gateway is ignored, and traffic in a subnet (for example, 192.168.50.10 - 192.168.50.11) flows. Destination Netmask Gateway Interface Metric 192.168.50.0 255.255.255.0 On-link 192.168.50.214 276 This route can be deleted from Windows, but when the machine is rebooted it always comes back. Adding a persistant static route to the gateway with a lower metric doesn't work, since it will still try the On-Link gateway after the persistant route fails. Adding each machine in a VLAN isn't an option due to the setup we have Adding a startup script to delete the gateway isn't a great option either, since users will have full admin access to the machine and might disable the script. We cannot transperantly intercept all network traffic on the subnet using Gratuitous ARPs or transparent proxying, since there are other machines on the subnet which use a different gateway The only way we have gotten it to work is by adding a persistant route to the gateway for the subnet traffic, and deleting the On-link route on reboot. The question is then. Is there a way to permanently remove this On-link route If not, is there a way to otherwise force even local subnet traffic to go through a gateway?

    Read the article

  • ESXi Server with 12 physical cores maxed out with only 8 cores assigned in virtual machines

    - by Sam
    I have an ESXi 5 server running on a 2-processor, 12-core system with hyperthreading enabled. So: 12 physical cores, 24 logical ones. On this server are 4 Windows 7 VMs, each configured for 2 processors, each running VMware Tools. Looking at my stats in vSphere, my "core utilization" is constantly maxed out. Yes, these machines are working hard, but only 8 cores have been allocated. How is this possible? Should I look into reducing the processor count per machine as in this post: VMware ESX server? I checked to ensure that hardware virtualization is enabled in the BIOS of the machine (a DELL R410). I've also started reading up on configuration, but being a newbie there's a lot of material to catch up on. It also seems I should only bother with advanced settings and pools if I'm really pushing the load, and I don't think that I should be pushing it with so few VMs. I suspect that I have some basic, incorrect configuration setting, but it's also possible that I have some giant misconceptions about virtualization. Any pointers? EDIT: Given the responses I've gotten so far, it seems that this is a measurement problem and not a configuration problem, making this less critical. Perhaps the real question is: How does the core utilization of the server reach a higher percentage than all individual cores' core utilization, and given that this possibility makes the metric useless for overall server load, what is the best global metric for measuring CPU load on hyper-threaded systems?

    Read the article

  • How can find the USB wireless adapter into the dmesg log file?

    - by AndreaNobili
    I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

    Read the article

  • Ubuntu-VirtualBox-LikeWiseOpen network disaster

    - by Sergio
    I've a virtual machine on VirtualBox 4.1.4 with Ubuntu 11.04. It was working perfectly, but after a reboot something really wrong happened: I wasn't able to connect to the internal network (same for NAT). $ sudo dhclient -v Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet System Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Error creating socket to list interfaces; Permission denied Can't get list of interfaces. The network interface is PCnet-FAST III. Additional information: $ uname -a Linux LinuxFileServer 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/Linux Any ideas? Thanks EDIT: $ sudo ifconfig -a eth1 Link encap:Ethernet HWaddr 08:00:27:af:f2:c7 indirizzo inet6: fe80::a00:27ff:feaf:f2c7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:1000 Byte RX:0 (0 B) Byte TX:3870 (3.8 KB) Interrupt:10 lo Link encap:Loopback locale indirizzo inet:127.0.0.1 Maschera:255.0.0.0 indirizzo inet6: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:0 Byte RX:960 (960.0 B) Byte TX:960 (960.0 B)

    Read the article

  • Internet doesn't work when enable local network

    - by rakesh yadav
    We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: Lan A) WAN interface (192.168.51.50) ( Used for internet) Lan B) LAN interface (192.168.30.228) ( used for local connectivity ) When I keep both LAN Enabled than my internet doesn't work, but if I disable my local LAN then internet works fine. How can I resolve this issue? Do I need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

    Read the article

  • How can I find the USB wireless adapter into the dmesg log file?

    - by AndreaNobili
    I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

    Read the article

  • virtualisation with kvm: export services from guest to the host

    - by ascobol
    Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

    Read the article

  • server and user directly connected no pinging...

    - by jtzero
    I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

    Read the article

  • Internet doesn't work when enable local Lan

    - by rakesh yadav
    We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

    Read the article

  • Network problems with Ubuntu on VMware

    - by svick
    I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

    Read the article

  • Ubuntu second static IP, ifconfig, /etc/network/interfaces

    - by Schmoove
    I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

    Read the article

  • When would a persistent route not be an active route?

    - by alnorth29
    I've added a persistent route to our Windows Server 2003 box using "route -p add". After a reboot the "route print" gave this: Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.91.131.1 10.91.131.9 20 10.88.0.0 255.255.255.252 10.88.0.1 10.88.0.1 30 10.88.0.1 255.255.255.255 127.0.0.1 127.0.0.1 30 10.91.131.0 255.255.255.0 10.91.131.9 10.91.131.9 20 10.91.131.9 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.88.0.1 10.88.0.1 30 10.255.255.255 255.255.255.255 10.91.131.9 10.91.131.9 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 224.0.0.0 240.0.0.0 10.88.0.1 10.88.0.1 30 224.0.0.0 240.0.0.0 10.91.131.9 10.91.131.9 20 255.255.255.255 255.255.255.255 10.88.0.1 10.88.0.1 1 255.255.255.255 255.255.255.255 10.91.131.9 10.91.131.9 1 Default Gateway: 10.91.131.1 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 10.88.0.0 255.255.255.0 10.88.0.2 1 The route I added is listed as a persistent route, but not an active one. Why might this be the case? The route in question is for an OpenVPN connection, would that have anything to do with it?

    Read the article

  • Android openvpn + zeroconf browser sending mdns query packets over eth0 instead of tap0 interface on wifi

    - by Mrunal
    On an android device, I am connecting to a remote network using openvpn for performing service discovery. WORKING CASE: After the device is camped on 3g/4g and after connecting to remote network by openvpn, when the zeroconf browser is launched, I can see the mdns query packets being send through the tap0 interface resulting into rendering of services on the browser. From the tcpdump captured on the device, I can see that the mdns query packets are send to tap0 interface. tap0 ip: 192.168.11.200 Route table information: Destination Gateway Genmask Flags Metric Ref Use Iface 76.26.112.234 10.179.240.1 255.255.255.255 UGH 0 0 0 pdpbr1 10.179.240.1 * 255.255.255.255 UH 0 0 0 pdpbr1 32.1.72.136 * 255.255.255.255 UH 0 0 0 pdpbr0 10.179.240.0 * 255.255.255.0 U 0 0 0 pdpbr1 192.168.11.0 * 255.255.255.0 U 0 0 0 tap0 default 192.168.11.1 0.0.0.0 UG 0 0 0 tap0 NOT WORKING CASE: However, after switching on the wifi and connecting it to remote network, when the zeroconf browser is launched, instead of sending the mdns query packets to tap0 interface; these packets are being send to eth0 interface due to which we cannot see the services. From the tcpdump captured on the device, I can see that mdns query packets are send to eth0 interface. tap0 ip: 192.168.11.200 eth0 ip: 192.168.43.230 route table information: Destination Gateway Genmask Flags Metric Ref Use Iface 76.26.112.234 192.168.43.1 255.255.255.255 UGH 0 0 0 eth0 32.1.72.136 * 255.255.255.255 UH 0 0 0 pdpbr0 192.168.11.0 * 255.255.255.0 U 0 0 0 tap0 192.168.43.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.11.1 0.0.0.0 UG 0 0 0 tap0 In the above case, even though there is a default route for tap0, all the multicast packets are being routed through eth0. How is this possible? Has anyone observed a similar problem and it would be really helpful if you can help us to discover services through zeroconf browser after the device is connected to remote network via openvpn through wifi. Thank You Very much, Mrunal

    Read the article

  • EC2 instance is blocking all outbound connections, how to diagnose/fix?

    - by Fraggle
    My EC2 instance is blocking all outbound connections. wget http://www.google.com ==> Hangs ping google.com ==>hangs ssh user@anyserver ==>hangs I ran : sudo iptables -F to eliminate all rules to no avail AWS Management console shows Security Group for that instance has Inbound rule allowing ssh and port 80. Can't find anything about Outbound rules there. Rebooted instance, no change. If anyone knows how to diagnose or fix, please help. Adding info: [ec2-user@ip-10-112-62-73 ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3D:06:31:BB inet addr:10.112.62.73 Bcast:10.112.63.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3dff:fe06:31bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1933 errors:0 dropped:0 overruns:0 frame:0 TX packets:1764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164075 (160.2 KiB) TX bytes:343256 (335.2 KiB) Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:672 (672.0 b) TX bytes:672 (672.0 b) [ec2-user@ip-10-112-62-73 ~]$ ip route show 10.112.62.0/23 dev eth0 proto kernel scope link src 10.112.62.73 default via 10.112.62.1 dev eth0

    Read the article

  • Routing subnet over GRE tunnel

    - by eMgz
    Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

    Read the article

  • How can I configure multiple default gateways on a CISCO Router?

    - by Spirit
    Does any one knows a way to configure a cisco router with multiple gateways - multiple gateways of last resort? I've tried adding a gateway of last resort twice (with different metric) but only one is shown: Router(config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 Router(config)# ip route 0.0.0.0 0.0.0.0 3.3.3.3 100 And the show ip route output was: Router# show ip route Gateway of last resort is 2.2.2.2 to network 0.0.0.0 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, FastEthernet0/0 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, FastEthernet0/1 32.0.0.0/30 is subnetted, 1 subnets C 32.2.2.0 is directly connected, Serial0/2/0 S* 0.0.0.0/0 [10/0] via 2.2.2.2 The point is that i cannot see the other route with higher distance metric? Anyone has a sugestion? I mean will this config work if the link on 2.2.2.2 fails? Will the router choose the other network 3.3.3.3, if the link 2.2.2.2 fails?

    Read the article

  • Amazon EC2 instance missing Network Interface

    - by Sergiks
    I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

    Read the article

  • Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

    - by larsks
    I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

    Read the article

  • Connect linux server to VPN server via PPTP

    - by wowpatrick
    I'm trying to connect a Linux (Ubuntu 10.04 LST) server to a VPN server via the PPTP client to an VPN server. I configured the PPTP client as said in the documentation. The connection is correctly added as an interface, but somehow the connection dose not work. ping -I ppp0 google.com dose not return anything and traceroute -i ppp0 only shows the first hop, and then displays nothing. Any ideas of what is going wrong? Incorrect routing configuration? ifconfig output for the configured interface: ppp0 Link encap:Point-to-Point Protocol inet addr:xx.x.xxx.xxx P-t-P:10.0.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1496 Metric:1 RX packets:415 errors:0 dropped:0 overruns:0 frame:0 TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:31428 (31.4 KB) TX bytes:32394 (32.3 KB) route output Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.x.x.1 * 255.255.255.255 UH 0 0 0 ppp0 xx.xxx.xxx.xx sp.ip 255.255.255.255 UGH 0 0 0 eth1 192.168.3.0 * 255.255.255.0 U 0 0 0 eth2 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 default sp.ip 0.0.0.0 UG 100 0 0 eth1

    Read the article

  • debian 6 losing a large amount of packets

    - by Sc0rian
    I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

    Read the article

  • linux container bridge filters ARP reply

    - by Dani Camps
    I am using kernel 3.0, and I have configured a linux container that is bridged to a tap interface in my host computer. This is the bridge configuration: :~$ brctl show bridge-1 bridge name bridge id STP enabled interfaces bridge-1 8000.9249c78a510b no ns3-mesh-tap-1 vethjUErij My problem is that this bridge is dropping ARP replies that come from the ns3-mesh-tap-1 interface. Instead, if I statically populate the ARP tables and ping directly everything works, so it has to be something related to ARP. I have read about similar problems in related posts, and I have tried with the solutions explained therein but nothing seems to work. Specifically: ~$ grep net.bridge /etc/sysctl.conf net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 arptables and ebtables are not installed. iptables FORWARD is all set to accept: Chain FORWARD (policy ACCEPT) target prot opt source destination The bridged interfaces are set to PROMISC: ~$ ifconfig ns3-mesh-tap-1 Link encap:Ethernet HWaddr 1a:c7:24:ef:36:1a ... UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 vethjUErij Link encap:Ethernet HWaddr aa:b0:d1:3b:9a:0a .... UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 The macs learned by the bridge are correct (checked with brctl showmacs). Any insight on what I am doing wrong would be greatly appreciated. Best Regards Daniel

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >