Search Results

Search found 3674 results on 147 pages for 'floppy drives'.

Page 130/147 | < Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >

• "Access is Denied" when executing application from Command Prompt

  - by xpda

  Today when I tried to run an old DOS utility from the XP Command prompt, I got the message "Access is Denied." Then I found that most of the DOS utilities would not run, even though I have "full control" over them. They worked just fine a few weeks ago, and I have not made any OS changes other than Windows Upgrades. Then I tried running edlin.exe and edit.com from the Windows\system32 folder. Same result - "Access is Denied." I tried running these applications from Windows Explorer and got the message "Windows cannot access the specified device, path, or file. You may not have the appropriate permissions to access the item." I am logged in as a member of Administrators and have full control over these files. I tried logging in as THE Administrator, with no change. I checked the security settings on the files, and have full control over all of them. I have tried copying the files to different drives, booting in safe mode, and running without antivirus and firewall, all with no change. Does anybody know what could cause this?

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Possible disk IO issue

  - by Tim Meers

  I've been trying to really figure out what my IOPS are on my DB server array and see if it's just too much. The array is four 72.6gb 15k rpm drives in RAID 5. To calculate IOPS for RAID 5 the following formula is used: (reads + (4 * Writes)) / Number of disks = total IOPS. The formula is from MSDN. I also want to calculate the Avg Queue Length but I'm not sure where they are getting the formula from, but i think it reads on that page as avg que length/number of disks = actual queue. To populate that formula I used the perfmon to gather the needed information. I came up with this, under normal production load: (873.982 + (4 * 28.999)) / 4 = 247.495. Also the disk queue lengh of 14.454/4 = 3.614. So to the question, am I wrong in thinking this array has a very high disk IO? Edit I got the chance to review it again this morning under normal/high load. This time with even bigger numbers and IOPS in excess of 600 for about 5 minutes then it died down again. But I also took a look at the Avg sec/Transfer, %Disk Time, and %Idle Time. These number were taken when the reads/writes per sec were only 332.997/17.999 respectively. %Disk Time: 219.436 %Idle Time: 0.300 Avg Disk Queue Length: 2.194 Avg Disk sec/Transfer: 0.006 Pages/sec: 2927.802 % Processor Time: 21.877 Edit (again) Looks like I have that issue solved. Thanks for the help. Also for a pretty slick parser I found this: http://pal.codeplex.com/ It works pretty well for breaking down the data into something usable.

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• Recommended drive encryption solution

  - by Chris Driver

  Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

  Read the article

• I need a driver for my Cardbus USB 2.0 card

  - by Carl

  The picture and details of the card are here: http://www.ht-link.com/en/ProductView.asp?ID=106 The Windows drivers for this don't work right. I tried them on my previous laptop, and then installed the ones off their included CD. (Note that the systems requirements includes a CD-ROM drive...) I have a new laptop, and lost the CD. The website that lists the drivers is broken - the download links don't work. It is here: http://www.ht-link.com/en/DownView.asp?ID=10 I need the very first link - The Win XP drivers for the HT-112NEC. The company does not reply to my e-mails. I've tried searching Google for other sources for the driver (I didn't bother with those sites that want me to install driver detection software or create a log-in for their site). [Here's the problem I am getting using the drivers Windows XP SP3 installs: When I plug in my USB 2.0 hard-disk adapter, a USB Mass Storage Device entry is added in the Device Manager, but there is no entry under Disk Drives, and a drive letter is not assigned, so I can't access the driver. Like I said, this card didn't work without their special drivers on my other laptop, either.]

  Read the article

• PST backup with Volume Shadow Copy Service

  - by NoMadMan

  I was asked to implement the task of backing up 35 PST files ranging from 800Mb to 2000Mb. Windows XP and Windows 2000 workstations are assigned to the users and we have a Windows 2000 domain controller we use to back up files on 3x 500Gb external hard drives. I found several methods from applications to scripts. Local or remote applications would be my last resort. I came across this script based on Volume Shadow Copy Service. CopyWithVss I wanted to know if there would be a problem if the path had spaces. Would mounting the destination path of each PST folder with a drive letter be more practical? My concern with mounting option is that i would eventually run out of letters since I have 35 and possibly more workstations to back up. Lastly, can someone give me an example of CopyWithVss if it were run on a production network? The script is a bit cryptic even after reading several times. Where in the script do I enter the source and the destination? I'm a Mac user so please excuse my ignorance with Windows platform.

  Read the article

• IBM BladeCenter S: Disk Configuration

  - by gravyface

  Have just the one storage bay right now (SAS 15K 600GB x 6) and have configured one storage pool in RAID 10 with 4 disks (and two global spares). For each blade, I've created a volume and mapped accordingly: Blade #1 400 GB Blade #2 200 GB Blade #3 100 GB Blade #4 100 GB When I boot up Blade 1 and enter into the UEFI Setup (F1) followed by the Adapters and UEFI Drivers LSI Logic Fusion MPT SAS Driver Utility, I see 4 disks: two are the on-board 73GB drives, the other two are 200GB each and assume I'm being presented with two logical disks from the volume I created and mapped to this blade. I was a bit surprised by this: I figured I would've been presented with one logical drive per volume, not two. I'm assuming I can just configure whatever RAID level I wish that supports two disks, but not really sure what the benefits/trade-offs here. Should I go with RAID 10 on top of RAID 10? RAID 0? Software RAID 0/1/10? Does it even matter? If this is "normal" to see two disks, then I'm going to likely just do some benchmarking and see if it makes a difference changing the RAID levels (my guess is no); if this is not normal, well, please let me know. :)

  Read the article

• Can't get php+sqlite working

  - by facha

  Hi, everyone I'm struggling all morning to make php work with an sqlite database. Here is a piece of php code that I try to execute: #less /var/www/html/test.php <?php $db=new PDO("sqlite:/var/www/test.sql"); $sql = "insert into test (login,pass) values ('login','pass');"; $db->exec($sql); ?> Here is how I've done tests: # sqlite3 /var/www/test.sql sqlite> create table test (login varchar,pass varchar); #chown apache:apache /var/www/test.sql #chmod 644 /var/www/test.sql Here is the stuff that drives me mad: When I execute from command line: #php test.php everything goes well. Sql is being executed and I can see a new row appear in the database. When I execute the same script from a browser - sql is not being executed. I don't get a new row in the database. There are no errors in the apache log file. Please, help

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• no administrator password for Windows 7

  - by huskergirl78

  I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

• Installing Debian 7.1 on FakeRAID/Intel Z77 results in boot with no grub menu

  - by user198982

  I'm trying to install Debian 7.1 from DVD onto 2x500GB drives which are set up in a FakeRAID mirror using the on-board FakeRAID provided by the Z77 chipset. I have followed the guide here https://wiki.debian.org/DebianInstaller/SataRaid. Namely, I booted into the expert install with the 'dmraid=true' option added, installed onto the RAID mirror which the installer correctly detected, then installed grub2 onto /dev/mapper/.. raid volume. I chose to use LVM (so a boot partition + LVM volume). As per the guide, I have uncommented the "GRUB_DISABLE_LINUX_UUID=true" line in "/etc/default/grub" and ran "update-grub" then "grub-install /dev/mapper/.." (with the right RAID device in the command). However, after I rebooted the system, all I got was a grub console. It did not load the menu. I checked and it seems that it never even generated a menu file. I re-installed Debian a few times since, trying out different options and also a few workarounds people posted online, but to no avail. The best I am getting is a grub console. No menu. Some times it will generate the grub.cfg, some times it won't, depending on the workaround I try. I was wondering if anyone else has experienced this issue. There is no need to preach how I should not use FakeRAID. I have seen others trying to figure this out so I think a resolution to this issue would be of interest to more than just me. Also, I first installed the system onto a small drive for testing something else. I made a backup with Acronis and was able to restore that onto the RAID mirror by using Universal Restore. When I installed it onto a 500GB without RAID, backed up using the same method, then restored onto a RAID volume of the same size, it would not boot and I got grub errors. Weird. I can post more details, just let me know what you want to see.

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Booting an Asus EeePC from a LiveCD USB stick

  - by Bryan

  I have two identical Asus EeePC netbooks that are both installed with Ubuntu. One of them was sitting on the closet shelf and the battery went completely dead. When I charged the battery and tried to boot the it, I got the "No init found" error. In trying to follow the suggested way to fix it posted here, I used the Startup Disk Creator on my Ubuntu 11.10 desktop machine to create a USB stick with a bootable Ubuntu 11.10 live CD on it (the netbook doesn't have a CD drive). I plugged the USB stick into the netbook with the init issues, went into the BIOS and selected the USB stick as the 1st choice to boot from, and did a hard restart. It then just stuck at the flashing underscore. Not knowing why it wasn't working, I tried booting my working netbook from the USB stick. When I got into the BIOS on the working netbook, I noticed the description in the boot order section for the USB device was different. On the non-working netbook, the description was SWISSBIT (the name of the USB stick) but on the working netbook it was just "Rem. Drive". I also noticed on the working netbook there was an additional option under the bootable order section that allowed me to choose which hard drive to boot from. This section showed two hard drives, one of them being my USB stick. So, rather than changing the device boot order, I selected the USB stick as the hard drive to boot from first and it worked like a champ - I was able to boot into the LiveCD on the USB stick. Seems to me the working netbook is seeing the LiveCD USB stick as a hard drive, where-as the non-working netbook is seeing it as a plain ol' USB stick. The BIOS is the exact same version on both netbooks... any idea why it works on one and not on the other?

  Read the article

• Software RAID 1 Configuration

  - by Corve

  I have created a software RAID 1 quite some while ago and it always seemed to work for me. However I am not completely sure that I have configured everything right and do not have the experience to check so I would be very grateful for some advice or just verification that all seems right so far. I am using Linux Fedora 20 (32 bit with plans to upgrade to 64bit) The RAID 1 should consist of two 1TB SATA hard drives. This is the output of mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Sun Jan 29 11:25:18 2012 Raid Level : raid1 Array Size : 976761424 (931.51 GiB 1000.20 GB) Used Dev Size : 976761424 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Sat Jun 7 10:38:09 2014 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : argo:0 (local to host argo) UUID : 1596d0a1:5806e590:c56d0b27:765e3220 Events : 996387 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 0 1 active sync /dev/sda The RAID is mounted successfully: friedrich@argo:~ ? sudo mount -l | grep md0 /dev/md0 on /mnt/raid type ext4 (rw,relatime,data=ordered) Basically my question are: Why do I only have 1 active device? What does the State removed at bottom mean? Also I noticed some strange error messages that I see on the console on system start and shutdown and always repeating in the background when I switch with Ctrl + Alt + F2: ... ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: COMRESET failed (errno=-32) ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ata2: irq_stat 0x00000040 connection status changed ata2: SError: { CommWake DevExch } ata2: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen ... Are these errors related to the RAID? Something seems wrong with the SATA devices.. All together the system works (I can read and write to the mounted raid) but I always had these strange errors on startup shutdown (probably always in the background). Thx for your help

  Read the article

• Recovering ZFS pool with errors on import.

  - by Sqeaky

  I have a machine that had some trouble with some bad RAM. After I diagnosed it and removed the offending stick of RAM, The ZFS pool in the machine was trying to access drives by using incorrect device names. I simply exported the pool and re-imported it to correct this. However I am now getting this error. The pool Storage no longer automatically mounts sqeaky@sqeaky-media-server:/$ sudo zpool status no pools available A regular import says its corrupt sqeaky@sqeaky-media-server:/$ sudo zpool import pool: Storage id: 13247750448079582452 state: UNAVAIL status: The pool is formatted using an older on-disk version. action: The pool cannot be imported due to damaged devices or data. config: Storage UNAVAIL insufficient replicas raidz1 UNAVAIL corrupted data 805066522130738790 ONLINE sdd3 ONLINE sda3 ONLINE sdc ONLINE A specific import says the vdev configuration is invalid sqeaky@sqeaky-media-server:/$ sudo zpool import Storage cannot import 'Storage': invalid vdev configuration I should have 4 devices in my ZFS pool: /dev/sda3 /dev/sdd3 /dev/sdc /dev/sdb I have no clue what 805066522130738790 is but I plan on investigating further. I am also trying to figure out how to use zdb to get more information about what the pool thinks is going on. For reference This was setup this way, because at the time this machine/pool was setup it needed certain Linux features and booting from ZFS wasn't yet supported in Linux. The partitions sda1 and sdd1 are in a raid 1 for the operating system and sdd2 and sda2 are in a raid1 for the swap. Any clue on how to recover this ZFS pool?

  Read the article

• I need to preserve a tape using symantec backup exec. I'm aving trouble doing so

  - by MrVimes

  Please forgive me if this is the wrong stack exchange site. Please suggest which one I should post this to if it is. There's an automatic tape machine running in a remote location, with software (symantec backup exec 11d) Recently one of the servers being backed up had problems with its raid controller, so one of the drives has become invisible. I need to preserve the last good backup of that drive so I am trying to replace the tape with the most recent backup of that drive on it with one of the scratch tapes (blank tapes) present in the machine. I've tried the following... Associate the blank media with the media set in question (Wednesday) For the existing media (the tape with the data I want to keep) I click 'move to vault' and move it to the offline vault. I associate it with something other than 'Wednesday' (a media set called 'keep data infinitely...') I then do an inventory on that slot. The above steps I'm led to believe are supposed to put the fresh tape in the slot that had the tape I want to keep in it. But it just keeps showing up as containing the tape I want to keep after the inventory. (after refreshing the device tree) I am a complete newbie with this software. Can you tell me what I'm doing wrong, and/or tell me how to acheive my desired goal Edit: Just want to point out that I did try to get help directly from symantec with this, but having jumped through countless hoops to create an account and create a support ticket my progress was halted by requiring something called a 'tecnical contact id' at the final step with no explanation of what it is or how to get one.

  Read the article

• GPO - Setting not applied, although policy is applied

  - by Kenny Bones

  This is rather strange. In our domain we have several terminal servers and this morning a user reported that no drives are mapped when he logs on to the terminal server. So, I checked Group Policy Results and compare two users. Both users have the exact same policies applied. But for this particular user, the Script section under User Configuration - Policies - Windows Settings is just not there. For the other user, which this is working fine for, it says under the Script section that Winning GPO is Terminal2008, which is the GPO that contains the script section. And the Terminal2008 GPO is applied to both users. Also, the loopback processing is set to Replace. What could be the cause for this? I've never seen this particular issue before. I mean, both users are in the same OU, they log on to the same terminal server and the same policies are applied to both. They do not however have the exact same group memberships, but should that matter? It's not stated that the script should be run only if the user is a member of a certain group either. Not sure if that could be done through that specific setting either.All I know is, the very same policies are applied to both users, in the same OU and the same computer. Meaning, the same policies should be applied? Edit: I just ran Group Policy Results on one of the other terminal servers, which are also in the same OU, and the Scripts section is there! This means that this particular user don't get this setting when he's logged onto this particular server. What could be the cause of this?

  Read the article

• Choice of filesystem for GNU/Linux on an SD card

  - by gspr

  Hi. I have am embedded ARM-based system running on an SD card. It's currently Debian GNU/Linux using ext3 as filesystem. As I'm about to reinstall the system, I started wondering about changing to a more flash-friendly filesystem. I've heard about JFFS2, YAFFS2 and LogFS, and they all seem suited to the job. Which one would you recommend? Also, I've heard there have been a lot of ext4 improvements to better suit SSD disks; am I to interpret that as running ext4 should be just fine? What do I need to think especially about in that case? I guess the usage of the system is important. But for the sake of generality, imagine it'll do standard desktop stuff (even though it is infact a small ARM-based system). Thanks for any replies. Edit: Wikipedia tells me (in a "citation needed" statement) that Removable flash memory cards and USB flash drives have built-in controllers to perform wear leveling and error correction so use of a specific flash file system does not add any benefit. Thus, I'm leaning towards sticking with an ext filesystem.

  Read the article

• Best way to create and restore a Drive Image with Windows 7? [closed]

  - by jasondavis

  Possible Duplicate: Want to create a system image I am about to build a new PC. I am a windows 7 user. For years now I have been wanting to install windows and all my favorite software, music, etc., and then make a drive IMAGE and be able to go in 6 months later or WHENEVER I want to start fresh and completely format my drives and restore my IMAGE and have all my settings, programs, etc be just5 like when I created the original image. I know there is many ways to do this but I have never done this 100% successfully and I have about a week to figure out how to do it perfectly for when I build my new PC. I have heard good things about using tried Acronis true image in the PAST for doing what I describe4, I tried using it but, but the newer versions are overly complex and don't even seem to work the way I hoped. I also see that Windows 7 has some sort of drive IMAGE creator itself as well. Does the newer Windows 7 image creator do what I am describing above? If it does do what I am asking for (complete drive image with windows, all programs and settings) saved to an IMAGE file that can easily be restored to ANY hard drive in the future? Please share your experiences, tips, ideas on how to achieve this the easiest and most reliable way please

  Read the article

• Boot records messed on dual boot (win7 and ubuntu) machine with SSD and HDD

  - by Michael

  i have a lenovo ideapad y570 with two hard drives: SSD and normal HDD both managed by RapidDrive and windows 7 pre-installed. First, i have shrunk my 500 GB HDD a little bit to make some place for a linux installation. Then i installed linux mint 12 to it, also installed grub onto the drive (dev/sdb). Installation programm has not allowed me to install grub on sda. Then i replaced linux mint with ubuntu 12.04 but installed grub onto the SSD (which is dev/sda and was the default-option). After that i could boot into my windows, only ubuntu worked. So i did a research, and tried: rewriting mbr of windows into sda1, reinstalling grub, replacing grub2 with grub-legacy, and now i think my partitions table are totally messed. Here is fdisk -l output: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /dev/sda2 411648 1009430959 504509656 7 HPFS/NTFS/exFAT Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5e5d1cc8 Device Boot Start End Blocks Id System /dev/sdb1 * 1979 884389887 442193954+ 12 Compaq diagnostics /dev/sdb2 884391934 976771071 46189569 5 Extended /dev/sdb5 884391936 937705471 26656768 83 Linux /dev/sdb6 937707520 967006207 14649344 83 Linux /dev/sdb7 967008256 976771071 4881408 82 Linux swap / Solaris I also cant mount any windows partitions to recover data. And when i open gparted, the whole sda-disk appears unallocated and it states "can not have a partition outside the disk!", also the end-sector address of /dev/sda2 confuses me. If i boot from the SSD, it throws some mbr error and wont boot, if i boot from the HDD, i only get the grub bash. How do i restore the partition tables? I can boot only from a live-cd at the machine. Thanks for any help.

  Read the article

• computer fails to boot during/after POST for five or six boots, then works

  - by N13

  For the last few days, my computer has had issues booting. I've seen two different behaviors: The screen displays the graphics card information, then begins to list the RAM, hard drives, etc. At different points in this process (after the graphics info), the computer shuts off. After five or six attempts, it then boots normally. In roughly the same time frame, the computer freezes, and fails to boot. I think it boots successfully on the next attempt. I've also noticed that in some instances, the computer freezes on shutdown. It gets right to the point where it should shut off, but doesn't. I recently combined the best parts of two different machines into this one. I'm booting to GRUB, with Ubuntu 12.04, Linux Mint 11 and Windows Vista (unfortunately) as my OS options. It has an Enermax Modu82+ 525W power supply, and I've used an online calculator to determine that my load shouldn't exceed 400W. I even unplugged a hard drive, but that didn't help. I found the latest BIOS, patched it and checked the settings, but that didn't fix it. I'm fairly certain this issue didn't exist at first, but might have started when the power at my new apartment dropped for a second. The machine is plugged into a surge protector strip, but it's old and I've heard they lose effectiveness with age. Is a power dip as damaging as a spike? If something were damaged, why would it boot successfully after five or six attempts? It's almost like the BIOS or PSU need to be primed. The trouble with debugging is that there seems to be a "grace period" after shutdown where the issue doesn't present itself again. What should I try next?

  Read the article

• GRUB reporting wrong partition type

  - by plok

  It all started when I had to replace one of the disks that the software RAID 1 on this machine currently uses. From that moment on I have not been able to boot to the Windows XP that is installed on the fourth hard drive, /dev/sdd. I am almost positive that the problem is related not to Windows but to GRUB, as if I unplug all the other hard drives so that the Windows XP disk is now /dev/sda it boots with no problem. The problem seems to be that GRUB detects a wrong partition type, which I understand suggest that something is really messed up. This is what I get when I try to follow the steps that until now had worked like a charm: grub> map (hd0) (hd3) grub> map (hd3) (hd0) grub> root (hd3,0) Filesystem type is ext2fs, partition type 0xfd 0xfd? That doesn't make sense. /dev/sdb and sdc are 0xfd (Linux raid), but not /dev/sdd: edel:~# fdisk -l [...] Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00048d89 Device Boot Start End Blocks Id System /dev/sdd1 * 1 30400 244187968+ 7 HPFS/NTFS edel:/boot/grub# cat device.map (hd0) /dev/sda (hd1) /dev/sdb (hd2) /dev/sdc (hd3) /dev/sdd I have been trying to work this out for hours, to no avail. Can anyone point me in the right direction?

  Read the article

• Why can't I browse my D: drive, even if I'm in the Administrators group?

  - by Nic Waller

  My fileserver running Windows Server 2008 has two logical drives; the C: drive contains all of the system and application data, and the D: drive contains all of the business data. There are several shares on the top level of the D: drive that are working fine. However... When logged into the fileserver interactively via Remote Desktop, only the Domain Administrator and local Administrator accounts can browse the D: drive. I set up an account called "Maintenance" and added it to the local Administrators group, but when logged in with this user, I can't browse into the D: drive. The D: drive has the following permissions ACL: Full Access - SYSTEM Full Access - MACHINE\Administrators It won't even let me view the ACL for the E: drive. So I tried taking ownership of the E: drive, then I can read the ACL, and "Effective Permissions" says that I have full access. But I still get this error message. Location is not available D:\ is not accessible. Access is denied. Here's a screenshot proving that I get access denied even when I have Full Access. http://www.getdropbox.com/gallery/2319942/1/errors?h=2bd644

  Read the article

< Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >