Search Results

Search found 13178 results on 528 pages for 'subsonic active record'.

Page 130/528 | < Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >

• Adding a second IP address for IIS - static vs dynamic A records

  - by serialhobbyist

  I'm looking to add a second IP address to IIS so that I can run two sites with different SSL certificates. When I added one on my play box and ran ipconfig /registerdns both addresses were registered in DNS with the server's name. So, I deleted the A record for the new IP address and rebooted. That also registered both names. So, then I went into the network config for the adapter and, on the DNS tab, unchecked "Register this connection's addresses in DNS". I deleted the A record for the new IP address again and re-ran ipconfig /registerdns. This time, it deleted the A record for the old IP address and didn't created one for the new address. Neither of these is what I want: I want the main IP address to be registered and refreshed automatically as a dynamic DNS record and the second IP address to be registered and managed as a static address. Is there any way to achieve this?

  Read the article

• Changing DNS - Forgot to change MX records for one month - Is there a way to retrieve emails that we

  - by Chris Altman

  We have our own domain. Our email is hosted by Google Apps. We switched web servers and name servers to a new provider. In the switch, I forgot to move the MX record. When people tried to send emails to our domain, there was no bounce back. We fixed the MX record and now receive email. Is there anyway to retrieve the emails that were sent in the month when there was no MX record? I doubt it because there was no MX record on our name server. Where would the emails have gone since they did not bounce back?

  Read the article

• How to correctly configure DNS for Icelandic domains and Plesk

  - by Leonard Challis

  I have a domain registered with ISNIC (domain.is). They only let you set nameservers that pass their requirements. I've been told it's this requirement that I need to fix: Nameserver must be consistently registered in DNS, i.e. its own A resource record must be available and a corresponding PTR resource record as well. I allocated two new IP addresses from my server host and at that point set their PTR records to ns0.domain.is and ns1.domain.is. After that I created two A records for that domain in Plesk, again ns0. and ns2.domain.is with their respective IPs. Next, I went to the ISNIC page to register my nameservers, along with their IP addresses I'd allocated and this worked perfectly for both without error. So the final job was to set the nameservers for the domain via ISNIC's control panel, however when I try, I'm getting this error: Test results for "NS0.DOMAIN.IS": The nameserver ns1.vps123.vpsprovider.com is not consistently registered in DNS (ns1.vps123.vpsprovider.com => 1123.123.123.123 => vps123.vpsprovider.com) The nameserver ns0.vps123.vpsprovider.com is not consistently registered in DNS (ns0.vps123.vpsprovider.com => 1123.123.123.123 => vps123.vpsprovider.com) The nameserver ns0.DOMAIN.IS is missing from the NS record set for DOMAIN.IS Test results for "NS1.DOMAIN.IS": The nameserver ns1.DOMAIN.IS is missing from the NS record set for DOMAIN.IS The nameserver ns0.DOMAIN.IS is missing from the NS record set for DOMAIN.IS This is really at the limits of my DNS knowledge I'm afraid. It feels like I'm close but maybe missing a vital part, linking the nameservers in Plesk or something?

  Read the article

• Android app hanging, sometimes until Force Close / Wait dialog appears

  - by fredley

  I'm making an app that records uncompressed (wav format) audio. I'm using this class to actually record the audio. Currently, my application records fine (I can play the file), however when I click the button to stop the recording, the app hangs for 10 seconds or so, with no log output or any signs of life. Finally it comes round, dumps a load of errors into the log, updates the UI etc. I'm using AsyncTasks to try and avoid this kind of thing but it's not working. Here's my code: //Called on clicks of the record button. rar is the instance of RehearsalAudioRecorder private OnClickListener RecordListener = new OnClickListener(){ @Override public void onClick(View v) { Log.d("Record","Click"); if (recording){ new stopRecordingTask().execute(rar,null,null); startStop.setText("Record"); statusBar.setText("Recording Finished, ready to Encode"); }else{ recording = true; new startRecordingTask().execute(rar,null,null); startStop.setText("Stop"); statusBar.setText("Recording Started"); } } }; private class startRecordingTask extends AsyncTask<RehearsalAudioRecorder,Void,Void>{ @Override protected Void doInBackground(RehearsalAudioRecorder... rs) { RehearsalAudioRecorder r = rs[0]; r.setOutputFile("/sdcard/rarOut.wav"); r.prepare(); r.start(); return null; } } private class stopRecordingTask extends AsyncTask<RehearsalAudioRecorder,Void,Void>{ @Override protected Void doInBackground(RehearsalAudioRecorder... rs) { RehearsalAudioRecorder r = rs[0]; r.stop(); r.reset(); return null; } } In Logcat, I always get output like this, which has me stumped. I have no idea what's causing it (I'm logging the RehearsalAudioRecorder class, and it's being started/stopped correctly by the button clicks. This output occurs after the log output for the button click and correct stop() method call) 12-19 11:59:11.172: ERROR/AudioRecord-JNI(22662): Unable to retrieve AudioRecord object, can't record 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): Error occured in updateListener, recording is aborted 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): stop() called on illegal state: STOPPED 12-19 11:59:11.172: ERROR/AudioRecord-JNI(22662): Unable to retrieve AudioRecord object, can't record 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): Error occured in updateListener, recording is aborted 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): stop() called on illegal state: ERROR 12-19 11:59:11.172: ERROR/AudioRecord-JNI(22662): Unable to retrieve AudioRecord object, can't record 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): Error occured in updateListener, recording is aborted 12-19 11:59:11.172: ERROR/uk.ac.cam.tfmw2.steg.RehearsalAudioRecorder(22662): stop() called on illegal state: ERROR ... 10 or more times I've been fiddling with this all day and I'm not getting anywhere, any input would be greatly appreciated. Update I've replace the AsyncTasks with Threads, still doesn't work, the app completely hangs when I click record, despite the fact the Log indicates there's nothing going on in the main thread. Still completely stumped.

  Read the article

• Labels mail merge repeats on subsequent pages?

  - by leeand00

  I'm trying to do a mail merge to print to labels. The first field in the document does not contain a { NEXT } field code, and because of this the records repeat between label pages for example: Notice how the records shift to the left as the next page is displayed? But how they start over again in an off by one manner? Now I've tried to fix this by using the first record displayed on a page to see if the page number is 1. If it not on page 1 of the mail merge then it should just move to the next record; otherwise it should just display the first record: This doesn't work however, because when I do the preview and display the {page} field code, it reports that I am always on page 1 and thus the same behavior continues instead of just moving to the next record on the next page.

  Read the article

• How to force mdadm to stop RAID5 array?

  - by lucek

  I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

  Read the article

• Third Monitor (Mini Display Port, Display Port)

  - by muhsing

  I have got a Hd 6950(2x minidisplay port 2x DVI port 1x HDMI port) graphic cards. And I have got a three monitor. I want to active it all. I learned to need an active minidisplay port to vga or minidisplay port to dvi cable. Here's my problem. I want to buy minidisplay port to dvi but my country doesn't have it but I can find display port to active dvi cable. I have a minidisplay port to display port cable. If I buy Sapphire ACTIVE DP TO SL-DVI CABLE will my third monitor work? I mean I will plug mini display port to display port cable first and after I will plug active dp to dvi cable. Will it work? If someone help me I will be very grateful. I have this And I will buy this After this processing Will my third monitor work with eyefinity? Sorry for my English. I hope you will understand me. Take care.

  Read the article

• How do I do a mail merge that includes images?

  - by Ian Ringrose

  I am trying to find out the practicalities of doing a mail merge when each “record” to be merged on includes some images. I need to: print letters And envelopes Both the letters and the envelopes have: Fixed text Fixed images Text that come from the mail merge record Images that come from the mail merge record I don’t know if all images will be the same size for every record, so a bit of simple “on the fly” automatic formatting may be needed . I need to be able to repeat a single item if I get a problem (e.g when folding the letter). What problems am I likely to have? Is Word 2007 up to this sort of mail merging, or should I be looking at a report writing tool? How do I restart a print run after a printer jam etc? What format should I store the “records” and there images in? E.g Can standard software cope with images that are stored in separate files named after the “CustomerId” that is in the “record” (I can write custom software if needed, but would rather use standard “of-the-shelf” software for the printing, I am planning on custom software for the data creation, so can output in whatever format is needed)

  Read the article

• understanding my site's DNS records

  - by DaveM

  firstly apologies for using the word 'pointage' this is the word my french domain registrar uses so I may have used to wrong term. OK I would like to better understand what is going on on my 'pointage' record on my domain registrars site. for my (currently empty) web site it reports the following details... Type : Host : Destination A : www.mydomain.org : 62.210.176.146 A : mail.mydomain.org : 84.246.225.176 Mx : .mydomain.org : mail.mydomain.org I think I understand the MX record, that simply relays anything onto the mail.mydomain.org location. However why are the destination for the www and mail domains different. Even more confusing (for me) is the fact that if I ping either of www.mydomain.org or mail.mydomain.org the ping returns a different IP address. This IP address is consistent with that of my server (ie 92.39.247.92). So what exactly is going on ? I'm sure I could find the information on the web,I've read a few thing on the debianhelp site regarding DNS records, and it seems to suggest that the record should be a reverse lookup, but certains isn't the reverse of my servers IP ? but I don't what I should be looking for, so links to docs and search terms for google will be happily accepteed (even though they go against the grain of SO answers to question). thanks in advance. David. ps. I should add that everything seems to work just fine, and I've just descovered this part of the management page of my registrar. Edit: Addition of DNS records and ping results. The DNS record for the site. From what I've read there should only realy be a single 'A' record, so has something gone wrong ? should I change it (remove the extras and then just point www.facilitee.org - .facilitee.org and mail.facilitee.org - .facilitee.org here is the DNS record A www.facilitee.org ? 92.39.247.92 A .facilitee.org ? 92.39.247.92 A mail.facilitee.org ? 92.39.247.92 A webmail.facilitee.org ? 92.39.247.92 MX .facilitee.org ? mail.facilitee.org ping results... ~$ ping www.facilitee.org PING www.facilitee.org (92.39.247.92) 56(84) bytes of data. 64 bytes from vps4576-cloud.dns26.com (92.39.247.92): ~$ ping mail.facilitee.org PING mail.facilitee.org (92.39.247.92) 56(84) bytes of data. 64 bytes from vps4576-cloud.dns26.com (92.39.247.92): So the DNS and the ping correspond, but the 'pointage' doesn't. ~ how can I get a report of the pointage records other than from my registrar ?

  Read the article

• How to display/define Mirror/Stripping pairs with mdadm

  - by Chris

  I want to make a standard linux software Raid10 over 4 HDD. The server has 4HDDs, 2 pairs from different vendors in order to avoid batch problems. I want to have the mirror over two different Vendors, and then the Stripe over the mirror pairs. I could do that by manually creating Raid1/0, but mdadm supports Raid level 10. I just cant figure out how the Raid10 is then handled and how the data is distributed. mdadm --detail /dev/md10 /dev/md10: Version : 1.2 Creation Time : Wed May 28 11:06:23 2014 Raid Level : raid10 Array Size : 1953260544 (1862.77 GiB 2000.14 GB) Used Dev Size : 976630272 (931.39 GiB 1000.07 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Wed May 28 11:06:23 2014 State : clean, resyncing (PENDING) Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 512K Name : pdwhost:10 (local to host pdwhost) UUID : a3de0ad5:9e694ee1:addc6786:c4449e40 Events : 0 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 113 3 active sync /dev/sdh1 does not really give any information about that. How it should be: Raid 1 / Mirror over /dev/sda1 /dev/sdf1 and /dev/sdg1 /dev/sdh1 Raid 0 over the two Raid 1 pairs Is it possible to do that with the built in "level=10", how can I see what pairs are mirrored? Thanks a lot for you help

  Read the article

• cPanel Redundacy

  - by bogha

  hi, what information should i know to do the following: we will have 2 servers, each one will have a cPanel WHM installed and 2 will have DNS, we want to insure that redundancy is achieved on both servers, means the servers should work as active/standby unit. 2 cPanel active/standby 2 DNS active/standby also does this have any impact on the mySQL database, do we have to buy another server to use it as the mySQL database or it's possible to sync all the cPanel information from one server to another. thank you.

  Read the article

• Juniper SSG20 IP settings for email server

  - by codemonkie

  We have 5 usable external static IP addresses leased by our ISP: .49 to .53, where .49 is assigned to the Juniper SSG20 firewall and NATed for 172.16.10.0/24 .50 is assigned to a windows box for web server and domain controller .51 is assigned to another windows box with exchange server (domain: mycompany1.com) mx record is pointing to 20x.xx.xxx.51 Currently there is a policy set for all SMTP incoming traffic addressed to .51 forward to the NATed address of the exchange server box (private IP: 172.16.10.194). We can send and receive emails for both internal and external, but the gmail is saying mails from mycomany1.com is not sent from the same IP as the mx lookup however is from 20x.xx.xxx.49: Received-SPF: neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=20x.xx.xxx.49; Authentication-Results: mx.google.com; spf=neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] and the mx record in global dns space as well as in the domain controller .50 for mail.mycompany1.com is set to 20x.xx.xxx.51 My attempt to resolve the above issue is to Update the mx record from 20x.xx.xxx.51 to 20x.xx.xxx.49 Create a new VIP for SMTP traffic addressed to 20x.xx.xxx.49 to forward to 172.16.10.194 After my changes incoming email stopped working, I believe it has something to do with the Juniper setting that SMTP addressed to .49 is not forwarded to 172.16.10.194 Also, I have been wondering is it mandatory to assign an external static IP address to the Juniper firewall? Any helps appreciated. TIA

  Read the article

• How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

  - by cagenut

  Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only The hell you are: [root@localhost ~]# mount -o remount,rw /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

  Read the article

• Storage replication/mirror over WAN

  - by galitz

  Hello, We are looking at storage replication between two data centers (600km apart) to support an active-passive cluster design for disaster recovery. The OS layer will be mostly Windows Server 2003/2008 with some OpenSuSE Linux used for performance monitoring on VMWare or possibly XenServer. The primary application service to replicate is Nvision. Datacenter 1 will have two storage systems for local active-passive or perhaps active-active replication with Datacenter 2 used as a last resport disaster recovery site. We have a handle on most aspects, but I am looking for specific recommendations on storage platforms that can handle remote replication cleanly. Thanks.

  Read the article

• Raid 5 with 4 disks on Debian automatically creates a spare drive

  - by Razer

  I'm trying to to create a RAID 5 with 4x 2TB disks on Debian 6. I followed the instructions from: http://zackreed.me/articles/38-software-raid-5-in-debian-with-mdadm I created the raid with following command: sudo mdadm --create --verbose /dev/md0 --auto=yes --level=5 --raid-devices=4 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 After creating the RAID mdadm --detail /dev/md0 shows me: /dev/md0: Version : 1.2 Creation Time : Mon Jun 11 18:14:26 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 11 18:14:26 2012 State : clean, degraded Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : rsserver:0 (local to host rsserver) UUID : a68c3c99:1ef865e9:5a8a7bdc:64710ed8 Events : 0 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 8 33 1 active sync /dev/sdc1 2 8 49 2 active sync /dev/sdd1 3 0 0 3 removed 4 8 65 - spare /dev/sde1 Why is there a spare drive? I didn't create one. I don't want to use a spare drive.

  Read the article

• How do you link a time stamp to a cell using a userform button control? [migrated]

  - by Chad Cochrane

  Hello fellow VB Developers/Users/Hobbyists/What-Have-You! I have a user form that has two buttons: 1. Start 2. Stop When I press start, I would like it to record the current time with this format: (dd/mm/yy hh:nn:ss:) in a specific column. Then when I press the Stop Button I would like it to record the time again in the cell next to it. Then if I press start Again I would like it to record below the first cells current record. Basically I am building a timer to record data to see how long certain tasks take. I will post the excel file and provide more information were necessary. Thanks for any help provided. CURRENT CODE Public runTimer As Double Public startTime As Date Dim counter As Date Sub setStart() counter = 0 startTime = Now runTimer = Now + TimeSerial(0, 0, 1) Application.OnTime runTimer, "setStart", , True Set myTime = Sheet4.Range("F1") Set timeRng = Sheet4.Range("C8:C100") i = WorksheetFunction.CountA(timeRng) i = i + 1 Cells(i, "C") = myTime Sheet4.Cells(i, "C").NumberFormat = "yyyy/mm/dd HH:mm:ss" If i >= 2 Then Cells(i, "D8") = Cells(i, "C8") - Cells(i - 1, "C8") Sheet4.Cells(i, "C").NumberFormat = "yyyy/mm/dd HH:mm:ss" End If Application.EnableEvents = False End Sub Sub setStop() Application.OnTime runTimer, "setStop", , True Set myTime = Sheet4.Range("F1") Set timeRng = Sheet4.Range("D8:D100") i = WorksheetFunction.CountA(timeRng) i = i + 1 Application.EnableEvents = False Cells(i, "D") = myTime Sheet4.Cells(i, "D").NumberFormat = "yyyy/mm/dd HH:mm:ss" End Sub

  Read the article

• root domain to www forwarding issue

  - by user182332

  I want to forward my root domain(yourdomain.com) to www.yourdomain.com Should I delete the A record of the root domain and then setup 301 permanent forwarding to www.yourdomain.com? I am hosting my app on heroku. So I don't really have an IP address to setup an A record. The thing is I first deleted the A record of my root domain and then forwarded it. I pinged it and here is the result - ping yourdomain.com ping: cannot resolve yourdomain.com: Unknown host Update and some more information - I am hosting a static website. And managing the DNS on cloudflare.com I added an A record for yourdomain.com - 184.168.221.51 Just an random IP.

  Read the article

• Setting a subdomain to access home machine with windows remote desktop

  - by ianhales

  I'm trying to remotely connect to home machine through Windows Remote Desktop (amongst other things, but this is currently my primary focus). I can do this fine using my home WAN's static IP (thank god for cable!) with port-forwarding, but I would like to access it from a subdomain of my web-site (e.g. home.mydomain.co.uk). In the cPanel for my hosting account, I've gone into DNS zones and altered the A-record to point to my WAN's IP, which I thought should do the job, but I still cannot connect. When I ping the subdomain, I get my web-host's IP, which I guess is to be expected as I believe the DNS of the host domain is used first, then my server handles the redirection of traffic to the IP in the A-record. Is this the correct idea? Do A-record changes suffer from the same propagation delays as DNS record changes, as I suppose that could explain it? (by the way, this thread confirms my thoughts that setting the A-record should be enough: Hostmonster Subdomain redirected to home server IP: How to ssh into home server using subdomain)

  Read the article

• How do I do a mail merge that includes images? (Maybe in Word 2007)

  - by Ian Ringrose

  I am trying to find out the practicalities of doing a mail merge when each “record” to be merged on includes some images. I need to: print letters And envelopes Both the letters and the envelopes have: Fixed text Fixed images Text that come from the mail merge record Images that come from the mail merge record I don’t know if all images will be the same size for every record, so a bit of simple “on the fly” automatic formatting may be needed . I need to be able to repeat a single item if I get a problem (e.g when folding the letter). What problems am I likely to have? Is Word 2007 up to this sort of mail merging, or should I be looking at a report writing tool? How do I restart a print run after a printer jam etc? What format should I store the “records” and there images in? E.g Can standard software cope with images that are stored in separate files named after the “CustomerId” that is in the “record” (I can write custom software if needed, but would rather use standard “of-the-shelf” software for the printing, I am planning on custom software for the data creation, so can output in whatever format is needed)

  Read the article

• Force Pinned taskbar items to be "icon only" all the time in Windows 7

  - by Robert

  By default (at least in my installation), pinned items on the taskbar will be "icon only" when they have no active windows, but when there are active window, the icon expanded to include text (typically some portion of the title text). I'm looking for a way to either: A (preferred option): For any single pinned item, force this pinned item to always display as just the icon even if it has active windows. OR B (acceptable option): Force ALL pinned items to always display as icon only in the taskbar

  Read the article

• Need to push a mass desktop background change

  - by StephanieTaylorAL

  I need to find a quick way to change the background on all computers on my domain other than going to each one of them. I have already tried gpedit.msc user configuration/administrative templates/desktop/active desktop and enabled active desktop and maped the active desktop wallpaper

  Read the article

• Adding ftp records as A or CNAME

  - by Saif Bechan

  Is it better to use a A record or CNAME record for FTP.

  Read the article

• Domain registration and DNS, what am I actually paying for? [on hold]

  - by jozxyqk

  Long story short I'm quite confused as to exactly what is offered by domain registration and dns service sites. When I go to the url "http://google.com", my PC connects to a name server and gets the IP for "google.com", then connects to the IP and says, give me the page for "http://google.com". AFAIK there are many name servers and they all cache these bits of information in some hierarchical network, but ultimately a DNS record must come from a single source (not sure what this is called). There are different kinds of records, that might not an IP but an alias/redirect to other records for example. Lets say I want my own domain name for some server. Maybe it even has a static IP but I want a nicer thing for people to remember, or my ISP assigns dynamic IPs and I want a URL that always works, or my website is hosted on a shared machine so the browser needs to send "http://mydnsname.com" to the webserver to distinguish it from other requests to the same IP but for different sites. Registering a domain costs a small amount of money per year. Where does this money go, not that I'm complaining :P? Is that really all it costs to maintain the entire DNS system of nameservers? If I just register the domain and nothing else, what do I get? Is that just reserving a name or hosting WHOIS information or have I paid for a dns recrord to be hosted? Can a domain alone have a record, such as an IP or be an alias to another? A bunch of sites out there offer other services, in addition to domain registration (I'm assuming they register the domain through another party for me). One example is "dynamic DNS" (DDNS), but isn't this just a regular DNS record that's updated regularly? Does it cost extra to update more often? Without a DDNS, can a DNS record still point to an IP? I've also seen the term "managed DNS" and have no idea where that fits in.

  Read the article

• How do I align my partition table properly?

  - by Jorge Castro

  I am in the process of building my first RAID5 array. I've used mdadm to create the following set up: root@bondigas:~# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Wed Oct 20 20:00:41 2010 Raid Level : raid5 Array Size : 5860543488 (5589.05 GiB 6001.20 GB) Used Dev Size : 1953514496 (1863.02 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 20 20:13:48 2010 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 1% complete UUID : f6dc829e:aa29b476:edd1ef19:85032322 (local to host bondigas) Events : 0.12 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 8 32 1 active sync /dev/sdc 2 8 48 2 active sync /dev/sdd 4 8 64 3 spare rebuilding /dev/sde While that's going I decided to format the beast with the following command: root@bondigas:~# mkfs.ext4 /dev/md1p1 mke2fs 1.41.11 (14-Mar-2010) /dev/md1p1 alignment is offset by 63488 bytes. This may result in very poor performance, (re)-partitioning suggested. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=16 blocks, Stripe width=48 blocks 97853440 inodes, 391394047 blocks 19569702 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 11945 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 Writing inode tables: ^C 27/11945 root@bondigas:~# ^C I am unsure what to do about "/dev/md1p1 alignment is offset by 63488 bytes." and how to properly partition the disks to match so I can format it properly.

  Read the article

• Sync custom AD properties to SharePoint Profile

  - by KunaalKapoor

  Here are some step-by-step instructions regarding configuring SharePoint to sync with custom AD attributes:Add the custom attribute in Active DirectoryThis part will have to be your doing; here is some documentation regarding creating customattributes in AD:http://msdn.microsoft.com/en-us/library/ms675085(VS.85).aspxhttp://technet.microsoft.com/en-us/magazine/2008.05.schema.aspxhttp://blogs.technet.com/b/isingh/archive/2007/02/18/adding-custom-attributes-in-active-directory.aspx2. Open up the miisclient.exe (C:\Program Files\Microsoft Office Servers\14.0\Synchronization Service\UIShell\miisclient.exe)a. This will have to be opened up with the farm admin account3. Click on "Management Agents" in the ribbon4. Right-click the Active Directory Management Agent ("MOSS-<name of sync connection>") and click "Refresh Schema"a. When prompted, enter the credentials for the farm account5. Once complete, close out of miisclient.exe6. Go into Central Admin --> Application Management --> Manage Service Applications --> Go into the User Profile Service Application7. Click on "Manage User Properties"8. Click on "New Property"9. Put in the correct information regarding the attribute that was created10. At the bottom of this page, under the "Source Data Connection" drop down, select the AD synchronization connection you have already configured11. For the "Attribute" drop down, select the new attribute you have created12. For the "Direction" drop down, select "Import"13. Click "OK"14. Run a full synchronization for the user profile service application and the custom property will get synced (as long as the attribute is set in Active Directory for the desired users)

  Read the article

< Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >