Search Results

Search found 4772 results on 191 pages for 'complex'.

Page 131/191 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

• Can I setup NAT for the same service, two public IPs on different routers to the same private IP?

  - by James

  This might be needlessly complex, but here goes. I've got two Firebox x550e devices. The first has a local IP of 10.0.0.1, public IP 64.x.x.x. The second has a local IP of 10.0.0.10, public IP 70.x.x.x. There is an FTP server on our LAN with a private IP of 10.0.0.55. I've set up NAT rules in each of the Fireboxes, on the first firebox it is 64.x.x.x-10.0.0.55 tcp 21, on the second 70.x.x.x-10.0.0.55 tcp 21. The first rule works fine. I can ftp to 64.x.x.x and everything's good. The second rule doesn't work. ftp to 70.x.x.x results in a connection timeout. The second firebox logs say the connection is being allowed through. The default gateway on the FTP server is 10.0.0.1 (the first firebox) If I change the default gateway on the server to 10.0.0.10, the rule on the second firebox starts working, but the rule from the first firebox stops. Is there some way to make this work for both rules?

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Is it worthwhile to block malicious crawlers via iptables?

  - by EarthMind

  I periodically check my server logs and I notice a lot of crawlers search for the location of phpmyadmin, zencart, roundcube, administrator sections and other sensitive data. Then there are also crawlers under the name "Morfeus Fucking Scanner" or "Morfeus Strikes Again" searching for vulnerabilities in my PHP scripts and crawlers that perform strange (XSS?) GET requests such as: GET /static/)self.html(selector?jQuery( GET /static/]||!jQuery.support.htmlSerialize&&[1, GET /static/);display=elem.css( GET /static/.*. GET /static/);jQuery.removeData(elem, Until now I've always been storing these IPs manually to block them using iptables. But as these requests are only performed a maximum number of times from the same IP, I'm having my doubts if it does provide any advantage security related by blocking them. I'd like to know if it does anyone any good to block these crawlers in the firewall, and if so if there's a (not too complex) way of doing this automatically. And if it's wasted effort, maybe because these requests come from from new IPs after a while, if anyone can elaborate on this and maybe provide suggestion for more efficient ways of denying/restricting malicious crawler access. FYI: I'm also already blocking w00tw00t.at.ISC.SANS.DFind:) crawls using these instructions: http://spamcleaner.org/en/misc/w00tw00t.html

  Read the article

• Application to automate Windows software installation in a test lab

  - by Marc

  I have several test environments (hyper-V) which contain a variety of windows servers. Each machine needs periodically rolling back to a given snapshot and then re-installing with the latest version of our software to test. The software installs are quite complex MSI's with a fair few option screens. I know that the installs can be driven from the command line, passing in parameters to override the wizard options. At the simplest level I suppose I could just write a batch file to kick off each install with the required parameters, however the values that are passed in do need to change from time to time (and environment to environment) so a tool with a config file and simple GUI seems like a better idea. I think what makes it slightly more painful is the multiple environments. For example one environment might contain 4 servers and need a config file with all the server names, service endpoints etc. Another environment might be a 1-box install with all names and endpoints set to localhost. So, ideally I want to be able to store different setup configurations and use them to run all the required installers with the relevant settings against the relevant machines. Before I go off to write the thing, does anyone know of an existing, simple, free tool that will let me achieve this?

  Read the article

• TCP: Address already in use exception - possible causes for client port? NO PORT EXHAUSTION

  - by TomTom

  Hello, stupid problem. I get those from a client connecting to a server. Sadly, the setup is complicated making debugging complex - and we run out of options. The environment: *Client/Server system, both running on the same machine. The client is actually a service doing some database manipulation at specific times. * The cnonection comes from C# going through OleDb to an EasySoft JDBC driver to a custom written JDBC server that then hosts logic in C++. Yeah, compelx - but the third party supplier decided to expose the extension mechanisms for their server through a JDBC interface. Not a lot can be done here ;) The Symptom: At (ir)regular intervals we get a "Address already in use: connect" told from the JDBC driver. They seem to come from one particular service we run. Now, I did read all the stuff about port exhaustion. This is why we have a little tool running now that counts ports and their states every minute. Last time this happened, we had an astonishing 370 ports in use, with the count rising to about 900 AFTER the error. We aleady patched the registry (it is a windows machine) to allow more than the 5000 client ports standard, but even then, we are far far from that limit to start with. Which is why I am asking here. Ayneone an ide what ELSE could cause this? It is a Windows 2003 Server machine, 64 bit. The only other thing I can see that may cause it (but this functionality is supposedly disabled) is Symantec Endpoint Protection that is installed on the server - and being capable of actinc as a firewall, it could possibly intercept network traffic. I dont want to open a can of worms by pointing to Symantec prematurely (if pointing to Symantec can ever be seen as such). So, anyone an idea what else may be the cause? Thanks

  Read the article

• Getting some French-Canadian keyboard strokes to work on English keyboard

  - by Gradient

  I'm trying to use some of the French-Canadian keyboard stokes I'm used to on an English keyboard. I would like to change the behaviour of some keys. I was able to implement these changes in Vim, but I would like them to be applied system-wide (for Windows and Ubuntu). Here's what I want to implement : If I press [a, the character printed is â. When I press [r, something that's supposed to stay normal, the characters printed are [r. If I hold [ for 3 seconds, [ is printed. I want this delay to be applied to all my modified keys. I want to map < to ' and the characters 'e to è. The complex problem here is that I only want the ' beside the ; key to produce the è character, NOT when I press the < (remapped to ') then e. I'll show you a .vimrc file that implements this, now I want this behavior system-wide: set timeout timeoutlen=3000 ttimeoutlen=100 inoremap [a â inoremap [A Â inoremap [e ê inoremap [E Ê inoremap [i î inoremap [I Î inoremap [o ô inoremap [O Ô inoremap [u û inoremap [U Û inoremap 'a à inoremap 'A À inoremap 'e è inoremap 'E È inoremap 'u ù inoremap 'U Ù inoremap }e ë inoremap }E Ë inoremap }i ï inoremap }I Ï inoremap }u ü inoremap }U Ü inoremap ]c ç inoremap ]C Ç inoremap / é inoremap < '

  Read the article

• Load balanced IIS. Should I use NLB, or linux-based reverse proxy, or something else?

  - by growse

  What would be the best approach for load-balancing at least 2-3 Windows 2008 R2 IIS webservers running a multitude of .NET applications? My choices appear to be: 1) Hardware-based network device load balancer, like a Cisco CSS 2) Windows NLB 3) Some sort of linux based proxy, either haproxy or other The three servers sit as VMs on a vSphere farm, so I have the ability to clone to up the instance count in times of high load. I control the switch that the vSphere hosts are plugged into (Cisco 3750), but don't control the switching/routing infrastructure beyond that to the clients. (1) Is too expensive, and probably overkill for my needs. I've included this in case someone figures out a cunning way to do it on my existing network kit, which I doubt. (2) would seem to be the obvious "built-in" option, but seems to be quite fiddly messing around with network interfaces, multicast, and generally other things that seem to be needlessly complex. It's also fairly stupid, in that it can't remove hosts from the pool if they start throwing 500 errors or otherwise go wrong (3) is the most interesting option, as it would appear to offer the most flexibility and customizability, but without having to mess around with the network. However, while I'm familiar with the reverse-proxy capabilities of lighttpd etc, I'm not that well read on other options like HAProxy, which might be able to offer a lot more. Which would you go for, and is there anything I've not thought of?

  Read the article

• Underbraces in Word math zones and dealing with stretchy parentheses

  - by Johannes Rössel

  Parentheses in Word usually stretch with whatever they're containing. This might be un-noticeable for things like but for stuff like it's definitely nice, especially compared to the fact that naïve LaTeX users often produce uglinesses such as There is a problem, however, when using under-/overbraces in math and putting parentheses around the complete term it becomes ugly. For simple things like shown here this can be solved by not letting the parentheses stretch which looks almost right. However, for more complex things it's certainly not an option: Both variants look horrible. So is there a way of letting the parentheses only stretch around the actual term parts, not including the under-/overbraces? Those are frequently used for annotations of individual pieces, so simply not using them is a bad idea too. In LaTeX you can get away with guesswork and using explicit sizes for the parentheses instead of relying on \left and \right but I haven't found a comparable option in Word yet. Since the underbrace is (tree-wise) a sibling of the term in parentheses it probably simply has to stretch and there probably can't be an algorithm that determines when to stretch or when not, considering that \above and \below are used for annotations as well but also for other things where perentheses have to stretch. Also, since the parenthesized expression is opaque from the outside one has to put the underbrace inside. From a markup point of view, at least. One can probably draw the rest around but that falls apart when styles change and wouldn't be a good idea either.

  Read the article

• Active Directory + IIS + SQL + ASP.NET

  - by Amira Elsayed Ismail

  I have sent the following question to stackoverflow website I have installed Windows server 2008 r2 on a virtual machine, Can I install Active directory with domain controller + IIS + SQL server on the same machine? I want to make web application and this web application will authenticate users from Active Directory, the web application should be published on the server IIS and the users should access it remotely from their home using domain name of my machine, Someone tell me that its very wrong to have IIS and Active directory on the same machine I got the following Answer You can't use ActiveDirectory over the internet. At least not without something like a VPN as a middle man. Their home computers will not be joined to the domain, so there is no pass-through authentication. Yes, it's a bad idea to put AD on the web server. Why is too complex to get into in an answer here. Suffice it to say that even if you did do this, it's probably would not work the way you are thinking it should. It's not impossible to do this. For instance, many of the Microsoft "Small Businesss" products put IIS, AD, and SQL Server on the same server. But, you kind of have to know what you're doing to configure it securely. Then I add the following comment Thanks for ur reply.so what you think about the best way to do this as I didn't do anything like that before should I install active directory on a machine and IIS on another machine ? and what about SQL should I add it to the same server of active directory ? I didn't mentioned also that it will be Microsoft dynamics server that will access some information about work and i have to read data from axapta also ? also what is VPN and how can I use it to let users access my web application anywhere ? Sorry for my long questions and thanks in advance so please if anyone can help I will be thankful

  Read the article

• One Active Directory, Multiple Remote Desktop Services (Server 2012 solution)

  - by Trinitrotoluene

  What I am trying to do is quite complex, so I figured I'd throw it out to a wider audience to see if anyone can find a flaw. What I am trying to do (as an MSP/VAR) is design a solution that will give multiple companies a session based remote desktop (companies that need to be kept completely seperate), using only a handful of servers. This is how I imagine it at the moment: CORE SERVER - Server 2012 Datacentre (All below are HyperV servers) Server1: Cloud-DC01 (Active Directory Domain Services for mycloud.local) Server2: Cloud-EX01 (Exchange Server 2010 running multi tenant mode) Server3: Cloud-SG01 (Remote Desktop Gateway) CORE SERVER 2 - Server 2012 Datacentre (All below are HyperV servers) Server1: Cloud-DC02 (Active Directory Domain Services for mycloud.local) Server2: Cloud-TS01 (Remote Desktop Session Host for Company A) Server3: Cloud-TS02 (Remote Desktop Session Host for Company B) Server4: Cloud-TS03 (Remote Desktop Session Host for Company C) What I thought about doing was setting up each Organisation in their own OU (perhaps creating their OU structure based on the Excahnge 2010 tenant OU structure so the accounts are linked). Each company would get a Remote Desktop Session Host server that would also serve as a file server. This server would be seperated from the rest on its own range. The server Cloud-SG01 would have access to all these networks and route the traffic to the appropriate network when a client connects and authenticated so they are pushed onto the correct server (Based on session collections in 2012). I won't lie this is something I have come up with quite quickly so there may well be something gapingly obvious that I am missing. Any feedback would be appreciated.

  Read the article

• Underbraces in Word math zones and dealing with parentheses

  - by Johannes Rössel

  Parentheses in Word usually stretch with whatever they're containing. This might be un-noticeable for things like but for stuff like it's definitely nice, especially compared to the fact that naïve LaTeX users often produce uglinesses such as There is a problem, however, when using under-/overbraces in math and putting parentheses around the complete term it becomes ugly. For simple things like shown here this can be solved by not letting the parentheses stretch which looks almost right. However, for more complex things it's certainly not an option: Both variants look horrible. So is there a way of letting the parentheses only stretch around the actual term parts, not including the under-/overbraces? Those are frequently used for annotations of individual pieces, so simply not using them is a bad idea too. In LaTeX you can get away with guesswork and using explicit sizes for the parentheses instead of relying on \left and \right but I haven't found a comparable option in Word yet. Since the underbrace is (tree-wise) a sibling of the term in parentheses it probably simply has to stretch and there probably can't be an algorithm that determines when to stretch or when not, considering that \above and \below are used for annotations as well but also for other things where perentheses have to stretch. Also, since the parenthesized expression is opaque from the outside one has to put the underbrace inside. From a markup point of view, at least. One can probably draw the rest around but that falls apart when styles change and wouldn't be a good idea either.

  Read the article

• tail -f and then exit on matching string

  - by Patrick

  I am trying to configure a startup script which will startup tomcat, monitor the catalina.out for the string "Server startup", and then run another process. I have been trying various combinations of tail -f with grep and awk, but haven't got anything working yet. The main issue I am having seems to be with forcing the tail to die after grep or awk have matched the string. I have simplified to the following test case. test.sh is listed below: #!/bin/sh rm -f child.out ./child.sh > child.out & tail -f child.out | grep -q B child.sh is listed below: #!/bin/sh echo A sleep 20 echo B echo C sleep 40 echo D The behavior I am seeing is that grep exits after 20 seconds , however the tail will take a further 40 seconds to die. I understand why this is happening - tail will only notice that the pipe is gone when it writes to it which only happens when data gets appended to the file. This is compounded by the fact that tail is to be buffering the data and outputting the B and C characters as a single write (I confirmed this by strace). I have attempted to fix that with solutions I found elsewhere, such as using unbuffer command, but that didn't help. Anybody got any ideas for how to get this working how I expect it? Or ideas for waiting for successful Tomcat start (thinking about waiting for a TCP port to know it has started, but suspect that will become more complex that what I am trying to do now). I have managed to get it working with awk doing a "killall tail" on match, but I am not happy with that solution. Note I am trying to get this to work on RHEL4.

  Read the article

• Bridging Wireless and Wired Interfaces in Linux

  - by The Daemons Advocate

  My network setup is something like: Wireless Router <---> Netbook <---> Ubuntu Desktop ...or, more verbosely (with interfaces): Wireless Router <--(wireless)--> (eth2) Ubuntu Netbook Ubuntu Netbook (eth0) <---(wired)----> (eth0) Ubuntu Desktop In a perfect world, I'd have the desktop wired, but weird circumstances combined with my wanting to understand more about networking in linux make me want to figure out how to bridge these two devices. A bit of googling has given me this example using bridge-utils, and here's how I'm (failing) to setup the bridge (on the netbook): sudo -i ifconfig eth0 0.0.0.0 ifconfig eth2 0.0.0.0 brctl addbr bridget brctl addif bridget eth0 brctl addif bridget eth2 ifconfig bridget up ...then, trying to make sure that the netbook can still get on the internets... route add default gateway 192.168.2.1 dhclient bridget What happens after this is that the dhclient command above (netbook) doesn't get served an IP, and the Desktop, if I run dhclient, it doesn't get served an IP. Some weird considerations might be that I'm running the Network Manager Applet that comes with Ubuntu. While I'm sure I can get a command line wireless configuration setup, it's a bit complex. Can someone give me a shout as to where I'm going wrong? I'd also like to note another related question titled 'Bridging my laptop’s wireless and wired adaptors', however the setup is different to mine.

  Read the article

• Sun Grid Engine (SGE) / limiting simultaneous array job sub-tasks

  - by wfaulk

  I am installing a Sun Grid Engine environment and I have a scheduler limit that I can't quite figure out how to implement. My users will create array jobs that have hundreds of sub-tasks. I would like to be able to limit those jobs to only running a set number of tasks at the same time, independent of other jobs. Like I might have one array job that I want to run 20 tasks at a time, and another I want to run 50 tasks at a time, and yet another that I'm fine running without limit. It seems like this ought to be doable, but I can't figure it out. There's a max_aj_instances configuration option, but that appears to apply globally to all array jobs. I can't see any way to use consumable resources, as I'd need a "complex attribute" that is per-job, and that feature doesn't seem to exist. It didn't look like resource quotas would work, but now I'm not so sure of that. It says "A resource quota set defines a maximum resource quota for a particular job request", but it's unclear if an array job's sub-tasks' resource requests will be aggregated for the purposes of the resource quota. I'm going to play with this, but hopefully someone already knows outright.

  Read the article

• Why is my mono/XSP site loading slow?

  - by acidzombie24

  I have two sites on the same server. One is loading perfectly and incredibly fast. The other is an equally complex site except a bit less javascript and 0 images. Its taking several seconds to load and there is a 1 in 3 chance that i get a Http500 error. WTF I grabbed the lastest 2.6.? version of mono, mod_mono and xsp (libgdiplus-2.6.7, xsp-2.6.5, mod_mono-2.6.3 and mono 2.6.7) This is whats in apache error.log [Mon Jan 03 19:33:40 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:33:40 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 this is the page error Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, webmaster@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny9 with Suhosin-Patch mod_mono/2.6.3 Server

  Read the article

• Can you transfer a Windows 7 XP-mode VHD to a new PC without the need for reactivation?

  - by Henk

  Hi. At the moment I am running Vista 32 bit and use VPC 2007 a lot. I have several W2000 VMs set up with complex software configurations. For me, one of the advantages of working with VPCs is that a VM can easily be copied to another PC (like a notebook). Also, when I move to a new PC, I can immediately work with my existing VMs without the need to reinstall all applications. I am thinking about buying a new pc with Windows 7 64 bit pro, and using the xp-mode VM that comes with Windows 7. The advantages would be support for more memory (so being able to run more VM's simultaneously) and having a licenced XP VM. I would like to know if you can transfer a VHD that is based on the xp-mode VHD to another machine without Activation issues. The other machine will of course, also be running W7. I would guess that this would not be a problem. However, I did read about a guy who had to reinstall his W7 because of a harddisk failure, and could not access his xp-mode VHD anymore because it demanded re-activation. Thanks. Henk.

  Read the article

• Outlook conversation view and categories

  - by Greg Jackson

  At work, I tend to receive a couple of hundred emails a day. To keep from being overwhelmed, I have been using categories to sort and prioritize my mail messages. I auto-assign categories, then group by them: Code Reviews, To, CC, Distribution List/BCC. This means that, for example, a message that's explicitly to me will always show up higher in my inbox than one I get because I'm on a Distribution List. It's a huge time saver and it brings important emails to my attention much more quickly. Recently, the email threads I'm involved in have started to get quite long, and I'd like to be able to use conversation view, or at least sort by subject. Outlook, however, doesn't seem to support any (useful) combination of conversation view and categories. I've tried the following things without success: Grouping by category, then conversation view -- Outlook gives me an error (the grouping/sort combination is too complex). Using a custom view to group by conversation -- category doesn't show up as an option to sort by Grouping by category, then subject -- Getting closer, but the top subject is the first alphabetically, not the most recent Grouping by conversation, then category -- This works, but it doesn't do me much good, because the top conversation is the latest, without regard to what category it belongs to Is there a way for me to retain my category system or something similar while taking advantage of grouping related emails together? I've written Outlook plugins in the past, so even that's not too out there to serve as a proper solution.

  Read the article

• What is the best way/Software to manage multiple short lived instances of virtual machines ?

  - by Newtopian

  Hi, We have a QA department that have to test our software on multiple combination of OS and DMBS. With Windows spewing out many different versions the combinatorial math of all this can be daunting. So we decided on visualizing our setups but so far it only displaces the problem. The cost of hardware is expensive and we need many different combination far exceeding your server capacity to deliver. Also, these instances are throw away, once the test is complete we no longer need it, furthermore to ensure proper test isolation we should start fresh from a new instance. Lastly we only need a small subset of these system online at any given time. What I am looking for is a way to manage inventory so that our QA staff can order instances to be put online as required and discarded once used. Instances are spawned from a pool of freshly installed systems with the appropriate combination ready to accept our software. It also should be possible for two or more people to start the same instance at the same time, though we could manage without this if it proves too complex to put in place. Finally our budget is pretty thin, we can probably make some purchases but ideally expenditures should be kept to a minimum. To summarize we should be able to : Bring instances online on demand. Ideally should offer queue and scheduling management Destroy instances on demand Keep masters in inventory but not online. Manage large inventory of VMs (30-100 maybe more) with small staff of users (5-10). Allow adding, deleting and changing instances from inventory (bring online, make changes and check back in, or create new and check in). Allow few long lived instances for support tools (normal VM server usage) Thanks for your answers

  Read the article

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

• Disable CTRL+mouse wheel zooming in Chrome?

  - by Peter Nore

  I'm a normal-sighted person and I would like to view pages at 100% all the time. I use keyboard shortcuts that involve CTRL a lot, so about twenty times a day I accidentally hit CTRL at the same time that I'm scrolling, which results in the page being reflowed and repainted. This in is annoying because it can take up to 30 seconds to fix the issue, depending on how complex the site layout is. On sites with dynamic layout such as Google Docs the problem is more serious; accidentally hitting CTRL+mouse wheel corrupts the display and forces me to refresh the page entirely, sometimes causing me to loose information in the process. I would like to either decouple CTRL+mouse wheel from zoom, or disable zoom functionality altogether. This is possible on Firefox by using about:config; is there a similar way to edit detailed settings in Chrome? Would I have access to the detailed settings if I used Chromium instead of Chrome? I'll probably jump ship back to Firefox if I can't solve this problem. There is a superuser question that asks basically the same thing I'm asking, but for Firefox and Internet Explorer exclusively. Other people on the Chrome forum have had related issues, but none have the same problem. "I would really like it if I could deactivate the auto zoom in/out." had "something with laptops and Windows 7", not the feature built into Chrome. Other people have had PDF specific issues, which doesn't concern me. I've also tried searching for extensions that allow you to disable the scroll; I had hoped that "Zoom Lock" would have the ability to lock the zoom at 100% and prevent CTRL+scroll wheel from distorting the display, but it doesn't work for my use case. Google Chrome version 9.0.597.84 (Official Build 72991) Operating System: Ubuntu 10.10

  Read the article

• Blink build with Xcode failed

  - by Merci

  I found a GPL-ed SIP client for Mac, Blink. I'd like to build it from source since the binaries are only available as paid download. Just FYI i'm studying programming at university but have no experience in building complex application from source. After downloading the content of the repository i opened the Xcode project and tried to build on OS X 10.7, Xcode 4.2.1. Unfortunately the build fail with 1 error and many warnings Most of the warnings are like this: Attribute Unavailable: Custom Identifiers in Interface Builder versions prior to 3.2 The error message is: Apple Mach-O Linker (ld) Error Command /Developer/usr/bin/clang failed with exit code 1 preceded by the warning Apple Mach-O Linker (ld) Warning directory not found for option '-L/Users/Sergio/Downloads/Blink/devel.ag-projects.com/repositories/public/blink-cocoa/Distribution/Frameworks' I notice that in the list of required files i have this files missing: Dependencies/Frameworks libgcrypt.11.6.0.dylib libgcrypt.11.dylib libgnutls-extra.26.dylib libgnutls.26.dylib libgpg-error.0.dylib libintl.8.dylib liblzo.1.dylib libtasn1.3.dylib Dependencies/Resources lib Frameworks/Linked Frameworks Sparkle.framework Products Blink.app It should be possible to download these files somewhere. Unfortunately googling did not help. There's no documentation on the project site.

  Read the article

• Recommendation for robust, customizable, open source, Java servlet-based forum software?

  - by Erik Hermansen

  There is a lot of forum software out there, but it seems to me that a lot of the popular choices are PHP-based. And for my project, I'd like something based on Java servlets so my team can make customizations to it. Another important feature is that I can completely change the pages to hide unwanted elements without too much work. So I'm looking either for a template system or easily editable scripts (i.e. JSPs) that have a clean view separation. Just having skin changes or CSS customization is not enough. I understand that if I have open source, I can change anything I want, but my point is that it should be easy and not requiring mastery of a complex code base. Finally, I want something that has been around for at least a year and deployed on some high-traffic sites. Clustering support (one database, multiple web servers) is highly desirable. Up-time is crucial since I have an SLA to support. What do you think?

  Read the article

• Generating new SID for Windows 7 cloned partition in Linux?

  - by Jack

  So I've read that the proper way to clone a Windows 7 partition is to run a Sysprep after the clone is complete. For MANY reasons, this is not possible the way we are cloning these drives (long story short, the drive should be fully up and running after we clone it, with all the settings already there and requiring no user intervention; and no, not even an answer file would work because the way we customize all the Win7 settings is complex and we do not want the user touching the settings). I understand Microsoft will not support Windows 7 clones if it is not sysprepped and that is fine for us. Acronis recovery tools get around this by ticking an option called "Create new NT signature", which resets the SID and GUID on any restore. Symantec has a tool called Ghostwalker which does the same thing. However, we are looking for a way to do this in Linux because we want to use open source tools to do the imaging (fsarchiver, partclone, etc. basically the same tools Clonezilla uses internally to clone NTFS partitions). The question is, if we clone using these tools in Linux, how would we generate a new SID thereafter (without the use of sysprep)? Is there any way to do it within a Linux environment? The whole image process is automated so if it is a simple command that I can just throw in my shell script, that would be even better. Of course, it would be nice to know if this is even possible. Any ideas? EDIT: Forgot to mention that the target machines we are restoring the image on are EXACTLY the same.

  Read the article

• Installing Windows Management Framework 3.0 basically destroyed WMI, how can I fix it without reinstalling the O.S.?

  - by Massimo

  Related, of course, to this question. Before discovering it was somewhat... dangerous, I installed Windows Management Framework 3.0 on a number of Windows Server 2008 R2 SP1 servers, and WMI got completely trashed on all of them. This is what the WMI namespace looks like on a normal server (this is from Server Manager - Configuration - WMI Control): This is what it looks like after installing WMF 3.0: Yeah. Everything except WMF 3.0's new features is gone. Needless to say, nothing seems to work anymore on those servers. And no, this is not due to some strange installation error, this happened on three servers which were perfectly working before installing WMF 3.0, and on all of them the installation completed succesfully. Admittedly, one of them had a somewhat complex setup (various System Center products and SQL Server instances)... but two of them are just plain standard domain controllers which do nothing else at all. How can I fix this mess without having to reinstall the O.S. on these servers? And why did it happen in the first place?

  Read the article

• How do I access my samba drive through several layers of network topology?

  - by stephenmm

  I have a new windows 7 Home Premium machine that is in a different room than my main computer area. As such I have to use a bridge and another router. Everything is working wonderfully except I cannot access the SAMBA drive with the new machine. I know that SAMBA is accessible as an older WinXP machine can access it. A picture of my network would probably be helpfull: To ISP | | +---------------------------+ | WAN | | Cable Modem | | (2WIRE678) | | | | | +---------------------------+ | +---------------------------+ | | (|) (|) +-----------+ | Belkin Router | | | | Wireless | | (F5D) |--+ +--| WinXP | | | |SAMBA USER | | | +-----------+ +---------------------------+ | | | | +------------+ | | Ubuntu | | | Apache + | | |SAMBA Server| | +------------+ | | +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ # # +---------------------------+ | | | Netgear Bridge | | (XET1001) | | | +---------------------------+ | +---------------------------+ | | | D-Link Router | | (DI-524) | | | | | +---------------------------+ | | | | +-----------+ | | | Win7 | |SAMBA USER?| +-----------+ More interesting data points: 1. I can ping the SAMBA server from the Win7 machine locally (Ie. 192.168.2.2) 2. I can access the webserver from the Win7 machine locally (Ie. 192.168.2.2) 3. I followed the advice to get Win7 and SAMBA to play nice: http://www.tannerwilliamson.com/2009/09/windows-7-seven-network-file-sharing-fix-samba-smb/ Sorry for being so long winded but it is kind of complex and I am really at a loss as to how to fix it. If any of you have some suggestions I would love to hear it!

  Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >