Search Results

Search found 9744 results on 390 pages for 'k means'.

Page 131/390 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

• Does Exchange support plussed users (e.g. [email protected]) or a similar mechanism?

  - by Jens Bannmann

  Sendmail supports a feature called 'plussed users'. Once enabled, emails sent to [email protected], [email protected] and [email protected] are automatically delivered just like mails to [email protected]. There is no need to register or set up these 'plus suffixes'. The user can just use them and set up client-side filtering rules on his own. Does Exchange support a similar mechanism? If so, how to enable it? Note that I don't want answers about other means of filtering, e.g. spam/junk filtering, server-side or client-side rules, email aliases/addresses that are configured explicitly and so on.

  Read the article

• On VMWare Server, how can I specify which Ethernet port should be the one to be bridged?

  - by DrDavid

  My server has 4 ethernet ports; 1 uses a APIPA address to connect to a DroboElite (that's how they're designed to work), 1 is connected to the LAN, and the other two are unused currently. The issue is that VMWare Server seems to have an affinity to the port that's connected to the Drobo, which means that it can never reach the internet. If I disable the Drobo port, everything works just fine. If I enable the drobo port, nothing works (well, the drobo works, but the virtual machine doesn't ;) ) How can I tell VMWare Server to NOT use the drobo port when I'm bridging the connection?

  Read the article

• Hiding a column from a pivot table without removing it from the chart

  - by Simon

  I have a pivot table with two columns: number of users who visited a website (impressions) and number of users who registered on the site (regs). The rows are for dates. I want to visualize the percentage of users who registered after visiting the site. Thus, I have the number of users for each cell as a value field, displaying it as percentage of impressions. Generating a pivot chart from the table, impressions and regs are plotted over date as a percentage of impressions. This means there is one line at 100% for impressions (always 100% of itself) and the graph for registrations below that. I'd like to remove the line for impressions, but when I set a filter to do so, registrations vanish as well, since the column for impressions is filtered from the pivot chart as well, turning the value field invalid. How can I just show registrations as a percentage of impressions in the chart?

  Read the article

• apxs cannot install mod_cloudflare on centos

  - by Adam

  [ Linux - CentOS - Apache 2.2 - mod_cloudflare - apxs2 ] I have changed my nameservers to point to CloudFlare. The problem is that all the IP addresses are coming in as CloudFlare's. This is no good, because I have to monitor and block some specific traffic. mod_cloudflare is supposed to resolve this but I have been unable to get this installed. The command in the documentation uses apxs2. I can't figure out how to install this, or if it just means for 'apache 2.4'. I'm running 2.2.3, and I can use 'apxs'. When I run: apxs -aic mod_cloudflare.c I get the error apxs:Error: Command failed with rc=65536 Does this mean I need apxs2 or something else? How do I get mod_cloudflare working on my server? I appreciate any help, the documentation is vague and limited.

  Read the article

• What tools can be used to monitor a web application? Beyond "doesn't 404"

  - by Freiheit

  I have an internal web application that has recently gone through a major version upgrade. I would like to monitor this application over the weekend and look for 'soft' errors. I will still need to spot check things by hand, but there are some common failure patterns that I think I can automate. Examples include data with bad formatting, blank rows in tables (indicates missing non-critical data), patterns for identifiers ("TEST" means one of my devs left a testing feed on), etc. I think there are applications out there that can be scripted to do things like: 1. log in 2. Go to $URL 3. select 3rd link in $LIST or $PATTERN 4. Check HTML from that link for $PATTERNS 5. Email report Are these goals sane? What applications/tools can help with this?

  Read the article

• How do I get the last value of a column in an Excel spreadsheet?

  - by Chris

  In column A, I have dates. In column B, I have my body weight logged for the day. I add one row to each every day when I weigh myself, so this means the data is sorted by date ascending. The weights, of course, fluctuate (though it would be nice if they would go down every day for my own personal benefit). For a couple of calculations, I want to get the latest (or last) weight entered in column B. Not the max or the min, but the last one entered in the column. I want it to work no many how many rows I enter. I use Excel 2007, if that ends up mattering.

  Read the article

• How to manage a home-grown YUM package repo?

  - by TomOnTime

  There are plenty of websites that explain how to manage a mirror of YUM repos. I want to run a repo for my home-grown packages. Is there a good way to manage such repos? What I need to do: Manage 3 repos: unstable, testing, stable Self-service functions that let users add/remove/promote packages (promote means moving a package unstable?testing or testing-stable). ACLs that control which users/groups may add/remove/promote packages. Automatically re-sign packages as they move repo to repo (since the GPG key for "stable" should be different than "unstable") Automatically run "createrepo" to update repodata when needed. Suggestions?

  Read the article

• Change popup format for Kopete in Gnome (Ubuntu 10.04)

  - by HorusKol

  After trialling Empathy which was included with Gnome/Ubuntu 10.04 I decided to go back to Kopete since I was losing chat messages. However, for some reason, Kopete is now displaying all popups in a big, ugly window with four options (ok, cancel, view, ignore, or something like that) that actually all seem to do nothing. I tried looking for options in Kopete to change the popup style to the nicer Gnome style one which goes up in the top-right of my desktop, but it doesn't seem to be possible with this release. So I had to resort to removing all popup messages from Kopete to prevent my screen being taking over by a popup requiring action for every incoming chat message. Unfortunately, this now means that I do not get any notifications when people message me - and so I can go a couple of hours without realising that they did. Anyone know how to get the nice, unobtrusive popups working in this version?

  Read the article

• Tools to monitor guest OS performance in vSphere

  - by Quick Joe Smith

  I am looking for some tool or way to retrieve performance data from guest VMs running under vSphere 4.1. I am currently interested in the 4 basic metrics: CPU(%), Memory(%), Disk availability(%) & Network utilisation(Kb/s). The issue I have is that all of vSphere's performance data is from a ESXi host perspective (active, shared, consumed, overhead, swapped etc.) which is far removed from the data from the VM's own perspective. For instance, I have a Windows server VM idling, using around 410MB (~25% of its allocated 2GB) as reported by Task Manager, and this is the value I'm after. vSphere's metrics seem unable to arrive at this figure by any reliable and repeatable means. Is anyone aware of tools that can obtain this kind of data? The simpler, the better.

  Read the article

• Scripted printer configuration changes

  - by David Steven

  I've got about a dozen Windows XP machines that I need to make a couple specific printer configuration changes to. The printer is "virtual" printer for an electronic delivery service. I'd like to not have to visit each machine individually. I already have the means to execute commands remotely on the machines, I just can't seem to find away to adjust these settings via command line or script. Specifically I need to be able to make the following changes: 1) As an admin user: - Device Settings - Font Substitution Table/Courier New - Change to "Courier" 2) As a specific* user: - Printer Preferences - Paper/Quality - Advanced - Change Graphic/Print Quality to "600 x 600" - Change Document Options/Printer Features/Graphics Mode to "HP-GL/2" *This change is a per user configuration, unless there's some way to make it once. In this situation I only really need it for a specific (different) user on each machine.

  Read the article

• nginx status code 200 and 304

  - by Chamnap

  I'm using nginx + passenger. I'm trying to understand the nginx response 200 and 304. What does this both means? Sometimes, it responses back in 304 and others only 200. Reading the YUI blog, it seems browser needs the header "Last-Modified" to verify with the server. I'm wondering why the browser need to verify the last modified date. Here is my nginx configuration: location / { root /var/www/placexpert/public; # <--- be sure to point to 'public'! passenger_enabled on; rack_env development; passenger_use_global_queue on; if ($request_filename ~* ^.+\.(jpg|jpeg|gif|png|ico|css|js|swf)$) { expires max; break; } } How would I add the header "Last-Modified" to the static files? Which value should I set?

  Read the article

• SQL 2008 Memory Usage

  - by Danilo Brambilla

  I have a SQL Server 2008 (ver 10.0.1600) running on a Windows Server 2008 R2 Enterprise server with 8 GB of physical ram. If I open Task Manager I can see on 'Physical Memory' section of 'Performance' tab that only 340 MB are Available of 8191 Total, but I can't see any process using such amount of memory. Please note SQL Server is memory limited to 6GB (Maximum Server Memory = 6000). If I open Sysinternals Process Explorer, I can see sqlsrvr.exe process has: Private Bytes: 227.000 K Working Set: 140.000 K Virtual Size: 8.762.000 K What does this means? Is there any way to free up this memory for other process? Why Virtual Size figure as allocated memory? I thought that Virtual Size was 'reserved memory' only.

  Read the article

• On RouterOS, how will transparent proxying (with DNAT) affect reporting of netflows?

  - by Tim

  I have a box running Mikrotik RouterOS, which is set up to do transparent web proxying, as described here. In short, this means that I have a firewall rule for destination NAT causing any port 80 traffic to get redirected to port 8080 on the router, which is received by the Mikrotik local web proxy. The local web proxy then makes the web request on the client's behalf, in this case to a parent web proxy server (which in turn does the real web request). My question is, how will this two-part process get reported in the logging of traffic flow information (netflows)? Looking at the logged information, what I seem to be seeing is this: One flow recorded from client machine (private IP) to remote proxy (8080) Another flow recorded from router to remote proxy (8080) The original request that the client made to port 80 isn't recorded. I want to write code to analyse traffic usage, so I want to be sure I'm not losing information if I discard the latter of these.

  Read the article

• Switching to Linux, Need backup help

  - by Stephen

  I have an existing Vista installation on my thinkpad x200 and I want to install Linux on my machine. I've done this several times already but I usually format the whole disk and dual boot on Windows and Linux. Which means I have to reinstall and reconfigure everything I had on Windows. What I want to do is backup my windows installation (into an image) and start a clean Linux installation, and run the windows image thru Vmware or Virtualbox. Whats the easiest way to do this? any free tools available? I've seen acronis but dont wanna buy it for a 1 time session only.

  Read the article

• How to parse pipe with multiple commands independently?

  - by yarun can

  How can I parse output of a single command by multiple commands without truncating at each step? For example ls -al|grep -i something will pass every line that has "something" in it to the next pipe which is fine, but that also means every other line in the pipe is discarded since there wont be matching the condition. What I want is to be able to operate on single pipe by many commands independently. In this case it a pipe from Mutt which passes the whole message body. I want to get grep, sed, delete and assign each of these to bash variables maybe. Initially what I want is to be able to assign "message id" to a variable, "subject" to another variable etc Then pass those into proper commands arguments. Here is how it will be MessageBodyFromMutt|grep something -Ax -Bx |grep another thing from the original message| sed some stuff from the original message| cut from here to there Obviously the above line does not do what I want. I want all these commands to operate on the original message body. I hope it makes sense

  Read the article

• Radeon hd 6570 black screen

  - by Sho

  I got some problem with new graphic card. Every time I use AMD Catalyst drivers on Windows or Linux, screen repeatedly goes black. This usually shows u when i open new cards in a browser, resize a window or run a program. Card runs smoothly on basic drivers but this means low resolution. 1940x1080 is native for my monitor so it causes a lot of problems. I've got a 600W Deus G1, so the power is not the problem. Maybe its a silly question, but would going form a vga cable to hdmi help to improve this situation? If not, can it be caused by slow processor or old mainboard? Im getting kinda confused about this whole thing...

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• SGE: downtime planning

  - by mousee

  I need to plan a downtime for a maintenance of my environment (or some part of my environment) by means of Sun Grid Engine. Is it possible to somehow use backfilling information to tell the grid engine to plan only those jobs on cluster which are able to finish (i have backfilling information) till let's say 10 am next day? Can I then at 10 am rely on the fact that all compute nodes are clean, jobs are only queued, no job is planned and so that I can start maintenance? Thank you for your time. mousee

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Server 2008 Task Scheduler and a CMD file

  - by Mark Smith

  Task Scheduler - I have a .cmd file I'm trying to execute on a regular basis through Task Scheduler. I've set the task so that it points to the cmd file. I want the task to execute even when no one is logged in. I've set the credentials associated with the task to the local service account. When I execute the task, nothing happens. The Last Run Result shows 0x1, this means it didn't execute properly. When I run the file from a command prompt it executes just fine. Any help out there would be appreciated. I would post the code but it has sensitive information in it and I'm not allowed to let the code outside. Thanks

  Read the article

• Minimizing windows to tray in xfce

  - by Gryllida

  For XFCE (v. 4.8), I'm searching for possible options to minimize windows to tray (iconify). This means that 1) they're not in the window listing and 2) they're not in the alt+TAB menu and 3) when closed, the window hides (it disappears from window listing but still stays running). "alltray" has some weird GTK-related bug (https://bugs.launchpad.net/alltray/+bug/589831; windows hide but unhiding doesn't do anything; they stay in the tray icon until the user undocks them). "trayer" complains that "another systray is already running" and there's no obvious workaround. This question here is to ask about possible minimalistic (as everything in XFCE is) solutions which don't involve manual compiling, and aren't an overkill like cairo-dock is (a rather bloated gnome-style application which creates a new large 'tray' instead of using the existing one). Thanks!

  Read the article

• How to open first n bytes of file in hexadecimal and edit it?

  - by Larssend

  I want to edit some .avi videos (cut them, to be precise) in VirtualDub but it failed to open the files. They are encoded in xvid, which I have installed, and play in KMPlayer without problem. Also, all other xvid videos can be opened and cut just fine by VirtualDub. I suspect there's something wrong in the first few bytes of these particular videos (the magic number?). This means I have to open the offending files in a hex editor and make some necessary adjustments to the header. Problem is, they are very large ( 3 GB each) and take very long time to open in UltraEdit. Can UltraEdit open just the first few bytes of a file? If not, do you know of an application that can do that? Edit: I'm using Windows XP.

  Read the article

• Delay before booting with laptop

  - by Priednis

  I have almost the same problem as in Delay before booting? My computer is a practically new (couple months) Lenovo X200 Tablet (System Model 7449FXG). So when I press the power button, the indicator light that means "computer is on" turns on, but nothing else happens for about 5 mins, after that the computer starts booting normally. The same happens also on restart. And no USB or any other device for that matter is plugged in to the computer. And at the delay time the monitor is blank - actually not on at all.

  Read the article

• How do I use qmqtool to list emails from a specific envelope sender?

  - by jimp

  Occassionally a user's email password will become compromised and the spammer will flood the Qmail queue with 10,000+ emails sent through a specific user's account. I know how to use qmqtool to remove messages that match a specific string: qmqtool -d -f "[email protected]" However the -f argument matches anywhere in the message. -f 'STRING' display comma separated list of message number(s) containing STRING. That means messages to, from, and even mentioning that email address will all be deleted. Does qmqtool (or another qmail tool) have a command for matching messages from a specific envelope sender? Note: I only want to match the authenticated sender, not the "From:" which is always forged in this case anyway.

  Read the article

• Apache on Mac Mavericks issue

  - by Michael

  Trying to run Apache so that I can create a testing server on my mac.When I start apache it starts, but it doesn't run (no connection to local host. Ill upload the unix,you'll see that after starting there is no processes, and I did a check to show you what was running on my port 80... I don't entirely know that means. Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start Michaels-MacBook-Pro-3:~ michaelramos$ ps aux | grep httpd michaelramos 348 0.0 0.0 2442000 624 s000 S+ 8:51AM 0:00.00 grep httpd Michaels-MacBook-Pro-3:~ michaelramos$ sudo apachectl start org.apache.httpd: Already loaded Michaels-MacBook-Pro-3:~ michaelramos$ sudo lsof -i ':80' COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME ocspd 96 root 18u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 20u IPv4 0x8402f926599c58df 0t0 TCP dhcp-92-67.radford.edu:49267->108.162.232.196:http (ESTABLISHED) ocspd 96 root 21u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED) ocspd 96 root 23u IPv4 0x8402f926599c50f7 0t0 TCP dhcp-92-67.radford.edu:49268->108.162.232.206:http (ESTABLISHED)

  Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >