Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 133/314 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• CheckPoint Endpoint Security VPN client co-existing with Windows VPN

  - by Nils

  Hey guys, I work as a consultant for a firm with a Checkpoint firewall. I have downloaded and installed the Checkpoint Endpoint Security VPN client. During the installation, I answered no to any questions pertaining firewall etc. - I just wanted the VPN client itself. However, after the installation, I am no longer able to use any of my pre-existing Windows VPN client connections. It does not matter whether the Checkpoint UI is running or not - shutting down the client does not fix the problem. Uninstalling Checkpoint VPN on the other hand fixes the problem. Does anyone know if it is possible to have both VPN clients work while being installed simultaneously? I don't need them to stay connected simultaneously, just avoiding to install/uninstall the Checkpoint client every time I have to use it is perfectly good. Thanks!

  Read the article

• VPN with wrong subnet mask

  - by Philipp Schmid

  I followed these instructions on www.hottonetworking.com to set up VPN on a clean install of Windows Server 2008 SP2 (not R2 yet). When I then establish a VPN connection to that machine from a client machine (running Windows 7 RC), everything succeeds (it seems since I get a 'Connected' state in the network sharing center window), but I end up with a subnet mask (according to ipconfig /all) of 255.255.255.255 instead of 255.255.255.0. The net effect is that I don't have local network or internet capability. What additional configuration steps do I have to do to get VPN with the proper subnet mask working? Update: Using the steps outlined in the Technet article mentioned by Mr. Nimble, I was able to get internet connection. Apparently the subnet mask is not an issue as my coworker was able to connect using his VPN connection and ping the server machine by name as well.

  Read the article

• WAMP, DD-WRT, Using DNSMasq to access multiple virtual hosts via aliases on local network

  - by christian

  I've updated my question to coincide with my progress I am attempting to configure WAMP on my development machine. I would like to use it in conjunction with DD-WRT's DNSMasq feature to access multiple virtual hosts via aliases (dev1.local,dev2.local,etc.) over my local wireless network. I have followed the following tutorial which allows me to setup virtual hosts and access on local network by ip addresses. http://www.logicspot.com/web-development-2/viewing-a-locally-hosted-website-with-your-smartphone/ I've got this up and running. For simplicity sake I'd still like to setup DNSMasq to connect via aliases. I have followed the following tutorial http://www.question-defense.com/2008/12/29/add-static-dns-entries-to-dd-wrt-router-firmware And the aliases load on my development machine, but I can not access via the aliases on my mobile devices connected to the local network. I can however access via IPs. Thanks for any help you can provide

  Read the article

• How to change local user home folder on Windows 2000 and above

  - by Adi Roiban

  I was using a local account on a Windows 7 desktop that is not connected to any Active Directory. After a while it was required to rename the local account. Renaming the account was simple using Local users and groups management tool. After renaming the user, the user home folder was not renamed and I could not find any information about how to change user home folder. I found the ProfileList registry folder but maybe there is a command line for doing such changes. HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList Any help is much appreciated. Thanks!

  Read the article

• Motherboard wiring

  - by ML

  I am putting a new motherboard in a chenbro chasis and I dont get how to plugin the wires for powerSW resetSW, etc. It is a SuperMicro P4DP6 motherboard. ** I cant post an image yet, but here is a long to the spot on the mobo where this goes: http://andrewslack.info/mobo.png The powerSW lead is a green and white wire. I have the wire for PowerSW in place as the white wire ground and I have tried the reverse even (green to ground). The wire is covering Pin 1 and 2 in the diagram And I press the power button on the machine and nothing happens. It worked before I replaced the motherboard, the 24-pin ATX power leas is connected as well as the 2dn 6-pin optional power. Thoughts?

  Read the article

• Motherboard wiring

  - by ML

  I am putting a new motherboard in a chenbro chasis and I dont get how to plugin the wires for powerSW resetSW, etc. It is a SuperMicro P4DP6 motherboard. ** I cant post an image yet, but here is a long to the spot on the mobo where this goes: http://andrewslack.info/mobo.png The powerSW lead is a green and white wire. I have the wire for PowerSW in place as the white wire ground and I have tried the reverse even (green to ground). The wire is covering Pin 1 and 2 in the diagram And I press the power button on the machine and nothing happens. It worked before I replaced the motherboard, the 24-pin ATX power leas is connected as well as the 2dn 6-pin optional power. Thoughts?

  Read the article

• How to connect two monitors to a macbook pro?

  - by CIRK

  I have a 13" macbook pro, and I need much more space right now, so I decided to buy two smaller monitors. (these from LG). But I don't really know how will I connect them. I've seen some products like this Diamond BVU195, but it's not currently in stores in my country. I've found these Equip 128450 USB 2.0 Display Adapter DELOCK USB 2.0 to DVI/VGA/HDMI Adapter The second one looks pretty cool, but it says that Windows is a system requirement or what, so I'm not sure if it will work with mac os x? So how did you connected multiple monitors to you mac, and are these adapters the best choices, if yes then is there an OS independent one?

  Read the article

• cannot ssh to computer behind a dd-wrt bridge

  - by Jayaraman

  In my home network , i have dd-wrt router in another room , which bridges wifi from main home router (linksys) to the computers wired behind dd-wrt router. Now I cannot ssh from my laptop ( connected to linksys wifi) to the computers behind dd-wrt wifi bridge. I am able to ping the individual computers behind the dd-wrt bridge. When it comes to ssh or telnet to the computers , it is blocked. What can I do to make dd-wrt bridge to open up all ports in the dd-wrt bridge ?

  Read the article

• Ad-hoc connection between iPhone and Macbook Pro

  - by Phil Nash

  I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

  Read the article

• Routing all Traffic through OpenVPN Tunnel

  - by Filip Ekberg

  I have installed OpenVPN server on Archlinux and am now using OpenVPN GUI on Windows 7, I can talk to other computers connected through the VPN but I have not yet figured out how to route all traffic through the tunnel. How do I do this? I figured I need to do it with route ( cmd command ) but I think i need some pointers here. I've followed the OpenVPN HowTo on the matter but that doesn't work, it simply doesn't push the "force the client to go through this gateway"-option. And changing from OpenVPN to a PPTP / IPSec alternative is not an option at the moment.

  Read the article

• How do I set up a public server on a network?

  - by tyjkenn

  I am trying to set up a personal cloud server with OwnCloud on Ubuntu. LAMP is all set up. I was able to access it using the external IP address when I connected it directly to the modem, but what if I what if I want my server to share a LAN? I still want it accessible over the internet, but then if I go to the IP address from a web browser, it just tries to log into to router admin tools. The internal IP address works across the LAN, but I want to be able to access it from anywhere. This may be simple and I may be over-thinking it, but how do access my server? The router I am using is ASUS WL-520GU.

  Read the article

• Dual monitors through 1 HDMI port

  - by Carlos

  I currently have a Dell Studio XPS 13 laptop connected to a 24" HP monitor (w2448hc). Im thinking on getting a second one, however am wondering what i need for the setup (hardware wise). Also I was wondering it there is any down side to it, or something i should be aware of. For example, image quality loss, GPU overloading, or anything important I should know. More than anything Im interested in your advice. Also the monitors do have built in speakers (HDMI sound output), is the sound going to be reproduced by only one monitor or both? Specs Model: Dell Studio XPS 13 OS: Genuine Windows® 7 Home Premium 64-Bit CPU: Intel® CoreTM 2 Duo P8600 (2.4GHz, 3MB L2 Cache, 1067MHz FSB) Chipset: NVIDIA® GeForce® MCP79MX RAM: 4GB 1067MHz DDR3 SDRAM Graphics: SLi NVIDIA® GeForce® 9500M - 256MB Thanks for your advice, if there is anything additional i need to buy an you have a personal preference pass the brand name so i can check it out. Thanks!

  Read the article

• Socket(TCPIP) Unstable

  - by Lee Kwan Wee

  I have a setup of a SCPI server in a Win7 PC and have 2 other programs talking to it locally(127.0.0.1) over TCPIP socket 5025 and 5029. This worked well and stable in a fresh PC, but when we moved it into our production lines and the IT dept added their policies and stuff, it became unstable. The PC is connected to the production floor server but both of the programs are running locally in the PC. The connection tends to be disconnected when there is an idle period. And it takes 5-6times to refreshing the connection to get it back. I'm not a programmer myself, so I'm hoping to see if anyone here can help with some answers. Thank you very much!! Regards, KwanWee.

  Read the article

• Which process is using my NAS?

  - by sethu

  I have a nas connected to my cluster. The NAS holds all our home directories. When I did a set of experiments last week, saving a 1 GB file to the nas took around 30 seconds. If i do the same to a local disk it takes 18 seconds. But when I tried doing the same process today, it takes 150 seconds. I am unsure what is the problem . Can someone help me pointout the issue? Is it possible to find out which process is accessing the NAS or how much NAS bandwidth is getting used ? Thanks for your help. -Sethu

  Read the article

• Networking Windows 7 and Vista

  - by foosion

  How do you set up a Windows Vista Home Basic desktop (wired) and a Windows 7 Home Premium laptop (wifi) on a home network so that they can share files and the printers connected to the desktop? The Win7 laptop may also be used on other networks. I'm going to have to set this up for my parents when I visit shortly. I currently use XP and am not really familiar with Vista or Win7 network setup. Would it be difficult to share between the Vista and Win7 machines and and XP machine? If not, how to add that?

  Read the article

• Cisco PIX 515 internet connection

  - by Steve

  We have a ASDL modem connected to a Cisco PIX 515 to a switch. We have managed to get the PIX setup with ethernet1 (inside) with our IP range 192.168.5.1-192.168.5.254 and the internal network is working fine. We are having difficulty getting a connection from the PIX through the router on ethernet0 (outside). We have managed to ping external networks by setting up IMCP echo/echo-reply but are unable to setup any other protocols in a similar manner. Can any one help with a few lines that could be typed into the console that will allow this connection?

  Read the article

• Unable to access VLAN host from VLAN interface in CentOS

  - by Amrit

  I am playing with VLAN (Virtual LAN) configuration on CentOS 6.4. I have 2 interfaces, eth0 and eth1. I have configured 2 VLAN interfaces eth0.20 and eth0.30 as #file: ifcfg-eth0.20 #------------- VLAN=yes DEVICE=eth0.20 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.20.1 GATEWAY=192.168.20.1 NETMASK=255.255.255.0 USERCTL=no #file: ifcfg-eth0.30 #------------- VLAN=yes DEVICE=eth0.30 TYPE=Ethernet ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=static IPADDR=192.168.30.1 GATEWAY=192.168.30.1 NETMASK=255.255.255.0 USERCTL=no Then connected a desktop to interface eth0 port using LAN cable and assigned 192.168.30.2/24 IP. When I try to ping 192.168.30.1 from 192.168.30.2 machine, It shows destination host unreachable. I am also not able to ping 192.168.130.2 from 192.168.30.1. However ping -I eth0 192.168.30.2 works fine. Any pointers?

  Read the article

• IPv6 address is not working in Ubuntu

  - by Alex Farber

  Telnet connection with echo service succeeds for localhost and 127.0.0.1 host names, but fails with ::1 host name: alex@u120432:~$ telnet localhost 7 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 123 123 ^] telnet q Connection closed. alex@u120432:~$ telnet ::1 7 Trying ::1... telnet: Unable to connect to remote host: Connection refused alex@u120432:~$ My own program trying to talk using IPv6 address fails as well. Why IPv6 address is rejected? OS: Ubuntu 12.04 32 bit.

  Read the article

• Web server behind MikroTik and dynamic dns

  - by danielrvt

  I recently purchased a MikroTik router, it works great! However, I haven't been able to make my web server work from outside my lan I'll explain better: I have two domains in my disposal, before I switched to Mikrotik, the were working perfectly and all my websites were online. Since I changed the router, every time I try to access my websites from outside my lan, my websites can't be found. I have my websites domains associated with a dynamic dns provider, I managed to create a port forwarding rule to redirect all my incoming traffic from port 80 to my web server, and it works, but only when I'm connected to my MikroTik router. Is there something else I have to do? PD: I also created a static dns rule in my router with my domains to associate it to my webserver (which is behind my router) PD2: All I want is to redirect requests from outside to my webserver...

  Read the article

• Exim mail server slow on sending through SMTP

  - by catalint

  It takes about 30 seconds for the server to send me the banner, but initial connection is done instantly only happens when I am at the office, from home it works fine at the office I have a rRns set-up for my client ip that it's not working. Server: Exim, public fixed ip, rDNS, no ports blocked, in a datacenter Config: hostlist loopback = <; 127.0.0.0/8 ; 0.0.0.0 ; ::1 ; 0000:0000:0000:0000:0000:ffff:7f00:0000/8 hostlist senderverifybypass_hosts = net-iplsearch;/etc/senderverifybypasshosts hostlist skipsmtpcheck_hosts = net-iplsearch;/etc/skipsmtpcheckhosts hostlist spammeripblocks = net-iplsearch;/etc/spammeripblocks hostlist backupmx_hosts = lsearch;/etc/backupmxhosts hostlist trustedmailhosts = lsearch;/etc/trustedmailhosts domainlist user_domains = ${if exists{/etc/userdomains} {lsearch;/etc/userdomains} fail} This happens super fast on the server: 30132 ident connection to 89.238.207.49 failed: Connection refused 30132 sender_fullhost = [89.238.207.49] 30132 sender_rcvhost = [89.238.207.49] 30132 Process 30132 is handling incoming connection from [89.238.207.49] 30132 host in host_lookup? no (option unset) 30132 set_process_info: 30132 handling incoming connection from [89.238.207.49] 30132 host in host_reject_connection? no (option unset) 30132 host in sender_unqualified_hosts? no (option unset) 30132 host in recipient_unqualified_hosts? no (option unset) 30132 host in helo_verify_hosts? no (option unset) 30132 host in helo_try_verify_hosts? no (option unset) 30132 host in helo_accept_junk_hosts? yes (matched "*") 30132 using ACL "acl_connect" 30132 processing "accept" 30132 check hosts = +trustedmailhosts 30132 sender host name required, to match against lsearch;/etc/trustedmailhosts 30132 looking up host name for 89.238.207.49 30132 IP address lookup yielded relay.easycomm.ro Client side 2011.09.14 13:08:13 SMTP (mail.server.ro): Begin execution 2011.09.14 13:08:13 SMTP (mail.server.ro): Port: 465, Secure: SSL, SPA: no 2011.09.14 13:08:13 SMTP (mail.server.ro): Finding host 2011.09.14 13:08:13 SMTP (mail.server.ro): Connecting to host 2011.09.14 13:08:13 SMTP (mail.server.ro): Securing connection 2011.09.14 13:08:13 SMTP (mail.server.ro): Connected to host ---> This is a 1 minute 5 seconds gap 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-genius.filipnet.ro ESMTP Exim 4.69 #1 Wed, 14 Sep 2011 13:09:26 +0300 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-We do not authorize the use of this system to transport unsolicited, 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220 and/or bulk e-mail. 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] EHLO CatalinDell 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-genius.filipnet.ro Hello CatalinDell [89.238.207.49] 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-SIZE 52428800 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-PIPELINING 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-AUTH PLAIN LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 HELP 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorizing to server 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] AUTH LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 VXNlcm5hbWU6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] dGVzdEBzcG9ydGd1cnUucm8= 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 UGFzc3dvcmQ6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] ***** 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 235 Authentication succeeded 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorized to host 2011.09.14 13:09:18 SMTP (mail.server.ro): Connected to host 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] MAIL FROM: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 OK 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] RCPT TO: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 Accepted 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] DATA 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 354 Enter message, ending with "." on a line by itself 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] . ---> This is a 1 minute 10 seconds gap 2011.09.14 13:10:28 SMTP (mail.server.ro): <rx> 250 OK id=1R3mPG-0004T4-7Q 2011.09.14 13:10:28 SMTP (mail.server.ro): End execution --- Initial info I've setup an email account on "Windows Live Mail" that comes with Windows 7 Receiving is super fast, but for some reason sending is very slow, I had to increase the outgoing timeout to 3 minutes in order to make it work. Server software is Exim / Dovecot / cPanel. Do you have any ideeas why there is a slow sending process? Thank you!

  Read the article

• Enable SMB file sharing on OS X - "Incorrect Password"

  - by Tim Robinson

  I have a Mac running Snow Leopard connected to an Active Directory domain. I can share folders on the Mac and view files from Windows without problems. When I try to enable my Mac account for write access through System Preferences, I'm prompted for my account's password. Even though I'm entering the right one, I get an "Incorrect Password" response. The same process works fine for the local Mac administrator account; it's the Active Directory account I'm having problems with. I followed the advice on this page on apple.com without success: (I used the Mac to reset my domain password, and re-created my login keychain) If you want to use a user account that existed before you installed Mac OS X 10.3 (Panther), you may need to reset the password for the account using Accounts preferences. Can anyone suggest what might be wrong? Until I fix this I can't write to my Mac file share from Windows.

  Read the article

• Jabber Breaks in Empathy

  - by Tim Lytle

  Using empathy in Ubuntu 10.04 (64 bit), everything worked great after initial setup. But after disconnecting and reconnecting, any Jabber connection (GTalk and Facebook Chat) gives a 'network error'. Tried disabling accounts and only connecting to GTalk, same error. Tried removing all accounts, adding GTalk, same error. Upgraded to the dev version of Empathy, connected once, then after going 'offline' and reconnecting, same error. If it just didn't work, I'd wait for some kind of fix. But it did work, but only once per install. How does that happen? Anyone with this problem that solved it?

  Read the article

• "net time" returns system error 5, "Access is denied", even when run as administrator

  - by Andrew Grant

  I am trying to run net time on a Windows 7 box with an account that is part of the Administrators group. When I run the command net time from an elevated command prompt I get the following error: System error 5 has occurred. Access is denied. Why is this happening? I've looked at this Microsoft Knowledge Base article and have gone through the steps. Both the computer and the DC are connected to the same NTP server and I've verified they're synced I'm working on a local account so there should be no permissions issues There is no local firewall running

  Read the article

• Wireless Network Issue, Disconnecting Randomly From Network

  - by Surfer513

  I'm having an odd problem with my wireless network. Here is the background information: Server (Windows Server 2008) 1 to 10 end user machines connecting to the network Layer 3 Access Point (Asus WL-330 gE) connected to ethernet of Server and all machines connect to the network via the AP The end user machines get a connection to the server with no problems initially. But then connections are randomly lost throughout the day to the server/network. The wireless NICs of the machines still see the wireless network but are unable to connect to it. Then after some time the connection is regained automatically. I initially thought there was a problem with this particular AP, but then I took the same make/model AP out of storage and still ran into the problem. Any ideas what could be causing this??? Very confusing that the wireless nics on the end user machines can still see the network but not connect, and that the connections are randomly lost/gained. Thanks in advance!

  Read the article

• Exchange ActiveSync with muliple email addresses

  - by Martin Robins

  I have Exchange 2007 SP2, and I have successfully connected my Windows Mobile phone via Exchange ActiveSync and can send and receive emails. I have two addresses within my Exchange mailbox, [email protected] and [email protected], with the second being set as the reply address. When I view my email addresses on my device, I see both of these email addresses, however when I send new messages it always selects the first email address as the reply address and not the second. It is probably worth pointing out that, like in the example provided above, the email addresses are shown alphabetically and the address being selected is the first alphabetically (just in case that matters). I would like to set the device to always select the reply address specified in the mailbox, or at least be able to ensure that the address I want is selected if I have to select it manually on the device, but cannot find any way to make this happen. Can anybody help?

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >