Search Results

Search found 14226 results on 570 pages for 'feature requests'.

Page 133/570 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • Can enabling a RAID controller's writeback cache harm overall performance?

    - by Nathan O'Sullivan
    I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

    Read the article

  • BIND master/slave does not respond for queries for its slave

    - by Savas
    Systems are all Centos 6.2 Lets say I have a masterdns with IP 10.2.1.2, authoritative for the 10.2.1.X subnet and let say it is domain example.com I have another two subnets, 10.2.2.X and 10.1.2.X Each one has its own DNS server, dns2 and dns1 respectively and let say these are domains dom2.example.com and dom2.example.com respectively. The masterdns server has slave zones for dns1, dns2 and respond to requests OK. The dns1, dns2 have the masterdns zones as slaves two, and respond to requests OK. So, the masterdns has as slave zones all the subordinate domains of example.com Each of dns1 and dns2 use masterdns as a forwards (which uses another dns cache/proxy server) for dns resolution of internet public domain names. It works OK that too. The problem is, and I cannot figure it out. Why queries for example at dns1 for hostnames of dom2.example.com do not resolve? If i use nslookup - masterdns at dns1 server, resolve (i use directly the dns facility of masterdns). If I use nslookup locally, meaning queries are sent to dns1, for hosts that are at dom2.example.com, they do not resolve. Everything other works OK.

    Read the article

  • AWS VPC ELB vs. Custom Load Balancing

    - by CP510
    So I'm wondering if this is a good idea. I have a Amazon AWS VPC setup with a public and private subnets. So I all ready get the Internet Gateway and NAT. I was going to setup all my web servers (Apache2 isntances) and DB servers in the private subnet and use a Load Balancer/Reverse Proxy to pick up requests and send them into the private subnets cluster of servers. My question then, is Amazons ELB's a good use for these, or is it better to setup my own custom instance to handle the public requests and run them through the NAT using nginx or pound? I like the second option just for the sake of having a instance I can log into and check. As well as taking advantage of caching and fail2ban ddos prevention, as well as possibly using fail safes to redirect traffic. But I have no experience with their ELB's, so I thought I'd ask your opinions. Also, if you guys have an opinion on this as well, would using the second option allow me to only have 1 public IP address and be able to route SSH connections through port numbers to respective instances? Thanks in advance!

    Read the article

  • Site hanging in iis7 - how do I troubleshoot?

    - by Chris Foot
    I am currently having a problem with a windows 2008 server running IIS 7. The server runs several sites but only seems to have the issue with one particular site. Every so often, the whole server slows to a crawl with nearly all requests timing out! Invariably, when we log in to take a look there is always an IIS process using up around 90% cpu. Looking into the worker processes in IIS there are usually one or two requests that have been running for a long time. They are always in the ExecuteRequestHandler state with ManagedPipeline as the module name and the current ones i'm looking at have been running for 7686248 (what units is this in, it doesn't say?). It is also not always the same page, in fact we have seen at least 3 different pages listed under url when this has happened. It seems that the only way to bring the server back to life is to kill the 90% process! The site is running under .Net 4.0 and the code on it is very similar to other sites on the server which do not have the problem! How do I start troubleshooting this?

    Read the article

  • Is it possible to add/register an MIB for the Windows built-in SNMP service?

    - by michielvoo
    I need to build monitoring into an existing .NET application. I will use SNMP to send the application's status to the Windows SNMP service. I have used a .NET library to create the SNMP SET request according to the MIB that I have been provided with, and with the correct community. My code now sends multiple 'variables' in a SET request, for example: Id: ".1.3.6.1.4.1.43607.1.1.1.1.1" (ObjectIdentifier) Data: 42 (Integer32) On my machine I have enabled the SNMP service, configured a community with READ/WRITE permissions, and added localhost to the list of hosts to accept requests from. When I send the SET request I get a response, but it has error status 17 which, according to MSDN means SNMP_ERRORSTATUS_NOTWRITABLE. The response also has error index set to 8, which is the number of variables I send. If I send 7 variables, the error index is set to 7. I think the problem is that the Windows SNMP service is preconfigured to only accept SET requests for a fixed set of MIBs. How can I get the Windows SNMP service to 'accept' my custom MIB SET request? Edit: I downloaded and installed the Windows Server 2003 Resource Kit and tried to 'compile' the MIB file with mibcc.exe ("SNMP MIB Compiler") but I have not been able to compile any MIB files (even the most basic ones like SNMPv2-SMI.mib).

    Read the article

  • Firefox proxy authentication with Kerberos: one service ticket per connection (Linux)

    - by Dari
    I am trying to enable proxy authentication via Kerberos for Firefox. The setup is: Active Directory domain (for LDAP and Kerberos; this works and I can log in the computer and get Kerberos tickets without problems) Microsoft Windows witness machine (on which Firefox runs fine with no ticket problem) CentOS 6.3 system with Firefox (the tests were performed with both the 10.0.1 ESR found in the CentOS package repositories and the 15.0.1 downloaded from Mozilla's website) BlueCoat proxy with Kerberos authentication enabled For the moment, Firefox requests an element of a website, gets an HTTP error code of "407 Proxy Authentication Required" from the proxy, gets a ticket granting service (TGS) from the domain for the proxy and performs the request again while passing the ticket. The transaction runs fine. However, when more elements are requested (in parallel), Firefox requests one more ticket per proxy connection. And this takes many DNS queries, Kerberos interactions with domain controllers and costs a lot of time (for example, the home page of Adobe takes several minutes to load and at the end, I have about 30 valid Kerberos tickets). I am stuck on this since a while, and help would be greatly appreciated. Minor information: the CentOS operating system is virtualized with VMware Player 3.1.3, but I do not think this would be a game changer.

    Read the article

  • Tomcat Solr times out

    - by user568458
    (Plesk 10.4 centos 5.8 linux apache2 server, with Tomcat5 on port 8080 and Apache Solr) I get "The connection has timed out" on requesting domain.com:8080 or www.domain.com:8080 or ip.ad.dr.ess:8080 Every reason I can find why this might be seems not to be the case: Plesk thinks Tomcat is running fine and lists it as an active service. The firewall currently has an accept all rule on port 8080. There's nothing relevant in the catalina tomcat logs (/var/log/tomcat5) - just some stuff from last time tomcat was started. There's no record at all of the requests that fail. netstat -lnp | grep 8080 gives the following, which I beleive means Tomcat is listening to requests to port 8080 on all ip addresses from any ip and any port (please correct me if I'm wrong): : tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 4018/java This covers every cause of this time out that I can find - so I must be missing something fundamental. It seems Tomcat is running, listening to the right port, is getting an appropriate IP address, is not obstructed by a firewall and is not failing after receiving a request in a way which would be recorded in the logs (so I believe it can't be out of memory, or anything like that). I'm all out of ideas on how to continue debugging this. I must have overlooked something obvious. Can anyone help?

    Read the article

  • IPtables - Accept Arbitrary Packets

    - by Asad Moeen
    I've achieved a lot on blocking attacks on GameServers but I'm stuck on something. I've blocked major requests of game-server which it aceepts in the form "\xff\xff\xff\xff" which can be followed by the actual queries like get status or get info to make something like "\xff\xff\xff\xff getstatus " but I see other queries if sent to the game-server will cause it to reply with a "disconnect" packet with the same rate as input so if the input rate is high then the high output of "disconnect" might give lag to the server. Hence I want to block all queries except the ones actual clients use which I suppose are in the form "\xff\xff\xff\xff" or .... so, I tried using this rule : -A INPUT -p udp -m udp -m u32 ! --u32 0x1c=0xffffffff -j ACCEPT -A INPUT -p udp -m udp -m recent --set --name Total --rsource -A INPUT -p udp -m udp -m recent --update --seconds 1 --hitcount 20 --name Total --rsource -j DROP Now where the rule does accept the clients but it only blocks requests in the form "\xff\xff\xff\xff getstatus " ( by which GameServer replies with status ) and not just "getstatus " ( by which GameServer replies with disconnect packet ). So I suppose the accept rule is accepting the simple "string" as well. I actually want it to also block the non-(\xff) queries. So how do I modify the rule?

    Read the article

  • Simplest DNS solution for remote offices

    - by dunxd
    I look after a bunch of remote offices that connect via VPN - a Cisco ASA 5505 in each office acts as Firewall and VPN end point. Beyond that we keep things as simple as possible in the offices to minimise the support burden. We don't have any kind of server except in offices large enough to justify having someone dedicated to IT. Basically there is the ASA, some computers, a network printer and a switch. One of the problems I am seeing in a lot of offices is that DNS requests looking up hosts inside our network often fail - I'm assuming timeouts due to the offices internet connection (they are all in developing world countries) having some sub-optimal qualities (e.g. high latency caused by VSAT segments, or packet loss. The obvious solution to this is to have some sort of local DNS service that can serve local requests - so I think it would need to do zone transfers from our Microsoft Windows 2008 R2 DNS servers at HQ. However, simply installing Windows Servers in each office is both expensive, and creates a support burden. This got me thinking about pfsense/m0n0wall on embedded devices - those can act as a DNS server, and could be configured at HQ and sent out as just something that needs to be plugged into the network and can then be forgotten about by the staff locally. Maybe there are some alternatives to the ASA 5505 that include some DNS functionality. Has anyone here dealt with the problem, either using some kind of embedded device, or found some other solution? Any gotchas or reasons to avoid what I have suggested?

    Read the article

  • How to automatically restart Apache service after HTTP 503 error?

    - by Gnanam
    Our production server is running Apache v2.2.4 on CentOS5.2. Mono v1.2.4 is integrated within Apache. Recently, we faced a problem in our production server. From Apache's access_log, I found a HTTP 500 internal server error for one of the HTTP request and all subsequent HTTP requests also failed but with HTTP 503 service unavailable error. From thereafter, none of the requests were successful. Also, only later some time, we realized that our application was not working because of this error and then we restarted Apache service. My questions are, in this kind of situation, how do I automatically restart Apache service when HTTP 503 error is encountered? Is there any Apache directive available to set? in general, what would cause a HTTP 503 error in Apache? NOTE: Mono helps in running applications developed in .NET on a Linux-based OS. EDIT: I agree on finding the root cause of this problem. In fact, we've been analyzing that too. Till we resolve it, am finding whether this could be restarted immediately on its own without having any downtime/service disruption for application users.

    Read the article

  • Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

    - by axk
    I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

    Read the article

  • Home-made HTTP proxy server [closed]

    - by Martin Dimitrov
    I wanted to help a friend who has some restrictions at work to visit certain sites. Locally, on a Windows 7 machine, I run Apache server and decided to make it a proxy just for the IP of my friend. So I added the following to the configuration file: ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Deny from all Allow from <his.ip> </Proxy> It worked fine. But shortly the proxy started to receive many requests of the form: 66.249.66.242 - - [22/Sep/2012:11:01:12 +0300] "GET /search?hl=en&lr=lang_en&as_qdr=all&ie=UTF-8&q=related:www.aarp.org/aarp-foundation/+allinurl:+foundation&tbo=1&sa=X&ei=BSy2T9L_L8PitQapwtHtBw&ved=0COQBEB8wPw HTTP/1.1" 403 208 66.249.71.36 - - [22/Sep/2012:11:01:49 +0300] "GET /search?hl=en&lr=lang_en&as_qdr=all&ie=UTF-8&q=related:www.aarp.org/aarp-foundation/+allinurl:+foundation&tbo=1&sa=X&ei=BOCzT-_WK8_0sgbki5XCDA&ved=0COABEB8wPg HTTP/1.1" 403 208 These are Google IPs. The requests are every 30 seconds or so. My friend is not at work today. In apache_error.log I see: [Sat Sep 22 11:09:20 2012] [error] [client 66.249.66.242] client denied by server configuration: C:/wamp/www/aclk [Sat Sep 22 11:09:47 2012] [error] [client 66.249.71.36] client denied by server configuration: C:/wamp/www/search What the hell is going on? Please, help.

    Read the article

  • mysql thread count

    - by Ryan M.
    We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

    Read the article

  • Apache going straight to 100% mem usage on localhost

    - by Dennis Pedrie
    Hi, I'm running XAMPP on a OS X testing server... I'm the only person sending requests to the server. I've never messed with Apache config before, so I'm kinda without a paddle here. When I start Apache, I get ~10 httpd processes started, and 95% idle CPU. When I request a WordPress page, the CPU usage goes to 50%, and the page loads in about five seconds. It seems like once the page has finished loading, the CPU usage jumps to 100%, almost all of that httpd. A ton of processes get started, and they don't go away, and their CPU usage stays the same. I've changed the MaxRequestPerChild setting and so forth, but nothing seems to solve the problem. Even now, having not send any requests for about 15 minutes, the CPU usage is at 100%. Here's the applicable settings: Timeout 10 KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 3 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 0 MaxSpareServers 2 MaxClients 20 MaxRequestsPerChild 50 </IfModule> I had always thought that once the request was made, Apache killed the process. Is there anything I can do to bring down the CPU usage, or is this just something I'll have to deal with? Thanks for helping out an Apache idiot.

    Read the article

  • Apache reports a 200 status for non-existent WordPress URLs

    - by Jonah Bishop
    The WordPress .htaccess generally has the following rewrite rules: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> When I access a non-existent URL at my website, this rewrite rule gets hit, redirects to index.php, and serves up my custom 404.php template file. The status code that gets sent back to the client is the correct 404, as shown in this HTTP Live Headers output example: http://www.borngeek.com/nothere/ GET /nothere/ HTTP/1.1 Host: www.borngeek.com {...} HTTP/1.1 404 Not Found However, Apache reports the entire exchange with a 200 status code in my server log, as shown here in a log snippet (trimmed for simplicity): {...} "GET /nothere/ HTTP/1.1" 200 2155 "-" {...} This makes some sense to me, seeing as the original request was redirected to page that exists (index.php). Is there a way to force Apache to report the exchange as a 404? My problem is that bogus requests coming from Bad Guys show up as "successful requests" in the various server statistics software I use (AWStats, Analog, etc). I'd love to have them show up on the Apache side as 404s so that they get filtered out from the stat reports that get generated. I tried adding the following line to my .htaccess, but it had no effect (I'm guessing for the same reason as the previous redirect rules): ErrorDocument 404 /index.php?error=404 Does anyone have a clever way to fix this annoyance? Additional Info: OS is Debian 6.0.4, and Apache version looks to be 2.2.22-3 (hosted on DreamHost) The 404 being sent back to the client is being set by WordPress (i.e. I'm not manually calling header() anywhere)

    Read the article

  • HTTPS/HTTP redirects via .htaccess

    - by Winston
    I have a somehow complicated problem I am trying to solve. I've used the following .htaccess directive to enable some sort of Pretty URLs, and that worked fine. For example, http://myurl.com/shop would be redirected to http://myurl.com/index.php/shop, and that was well working (note that stuff such as myurl.com/css/mycss.css) does not get redirected: RewriteEngine on RewriteCond ${REQUEST_URI} !^(index\.php$) RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^/?(.*)$ index.php/$1 [L] But now, as I have introduced SSL to my webpage, I want the following behaviour: I basically want the above behaviour for all pages except admin.php and login.php. Requests to those two pages should be redirected to the HTTPS part, whereas all other requests should be processed as specified above. I have come up with the following .htaccess, but it does not work. h*tps://myurl.com/shop does not get redirected to h*tp://myurl.com/index.php/shop, and h*tp://myurl.com/admin.php does not get redirected to h*tps://myurl.com/admin.php. RewriteEngine on RewriteCond %{HTTPS} on RewriteCond %{REQUEST_URI} !^(admin\.php$|login\.php$) RewriteRule ^(.*)$ http://%{HTTP_HOST}/${REQUEST_URI} [R=301,L] RewriteCond %{HTTPS} off RewriteCond %{REQUEST_URI} ^(admin\.php$|login\.php$) RewriteRule ^(.*)$ https://myurl.com/%{REQUEST_URI} [R=301,L] RewriteCond %{REQUEST_URI} !^(index\.php$) RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^/?(.*)$ index.php/$1 [L] I know it has something to do with rules overwriting each other, but I am not sure since my knowledge of Apache is quite limited. How could I fix this apparently not that difficult problem, and how could I make my .htaccess more compact and elegant? Help is very much appreciated, thank you!

    Read the article

  • Setting up squid proxy server to in turn connect using another proxy server [closed]

    - by AnkurVj
    My institute uses the Squid proxy server and authentication mechanism requires username and password to be entered. This means that, I can log in on only one machine at a time and Internet access for me is restricted to that machine. I sometimes require Internet access on multiple machines simultaneously. What previosuly worked for me was the following : On one of my own machines A, I set up a Squid proxy server that allowed all local machines without any username and password. I configured rest of the machines to use this machine A as the proxy server. On machine A I logged into the institute proxy server using my browser. This way, I could access Internet from all my machines, by effectively channeling my requests through the server A. Recently, I lost that machine and configuration and now I tried to set it up again in the same manner. However, I cant seem to remember exactly how I made it work. I keep getting Connection Refused (111) on other machines. My guess is that my squid server isnt able to forward requests from other machines to the actual squid server. I could use any help for debugging this problem. I don't want to use alternatives such as ssh tunneling. This solution has worked for me in the past, I just don't remember how to set it up the same way again.

    Read the article

  • IIS 7.5 truncating POST body containing JSON data with ASP.NET MVC 3

    - by Guneet Sahai
    I'm facing a problem which I hope is a configuration thing with IIS but is right now giving a lot of trouble. Basically I have a controller that accepts a JSON and does some processing. While it generally works fine, but every now and then when the system has some load I get an error. After some painful debugging, we figured the incoming JSON gets truncated which causes the deserialzer to fail. To narrow down the problem - we wrote a simple controller that accepts a JSON and tries to deserialize it. In case it fails it just logs it. This works fine but when I hit it using a load testing tool (JMeter) it throws the same error (truncation) for a few requests. The # of failures increased when I increase parallel connections. It starts showing with 150 concurrent requests. We are running IIS 7 on windows 2008 server with ASP.Net MVC 3 with more or less default configuration of IIS. More information available in my question below http://stackoverflow.com/questions/12662282/content-length-of-http-request-body-size

    Read the article

  • Understanding tcptraceroute versus http response

    - by kojiro
    I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

    Read the article

  • Configuring wsgi for a simple Python based site

    - by jbbarnes
    I have an Ubuntu 10.04 server that already has apache and wsgi working. I also have a python script that works just fine using the make_server command: if __name__ == '__main__': from wsgiref.simple_server import make_server srv = make_server('', 8080, display_status) srv.serve_forever() Now I would like to have the page always active without having to run the script manually. I looked at what Moin is doing. I found these lines in apache2.conf: WSGIScriptAlias /wiki /usr/local/share/moin/moin.wsgi WSGIDaemonProcess moin user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup moin And moin.wsgi is as listed: import sys, os sys.path.insert(0, '/usr/local/share/moin') from MoinMoin.web.serving import make_application application = make_application(shared=True) QUESTION: Can I create a similar section in apache2.conf pointing to another wsgi file? Like this: WSGIScriptAlias /status /mypath/status.wsgi WSGIDaemonProcess status user=www-data group=www-data processes=5 threads=10 maximum-requests=1000 umask=0007 WSGIProcessGroup status And if so, what is required to convert my simple_server script into a daemonized process? Most of the information I find about wsgi is related to using it with frameworks like Django. I haven't found a simple howto detailing how to make this work. Thanks.

    Read the article

  • issues with Nginx + Passenger Production setup - Loading time/request time delay

    - by Dani Cela
    having a bit of an issue relating to request time. I have NGINX as a proxy server for a ruby on rails app running passenger. I also have a postgresql database server which is running on its own VM separate from my nginx/application server. My issue is that when I try and access my products page which does a lot of database queries, my query takes maybe 3-4 seconds. The second I flood the web server with requests, i will choke out the web server and have requests take almost 20-30 seconds to process. The rails server and database server do not crash, and the usage is not that high. Each server has more than enough memory, even cpu usage on the rails server isn't more than 85%, albeit thats high but its not maxing it out. Is my problem related to my nginx proxy server? I dont really know how to fully explain this so if you have a question please ask it and I can clarify what I mean. EDIT: to see exactly what i mean relating to the database query, see http://207.245.4.215/products

    Read the article

  • Setting up port forwarding for web server

    - by Javier Badia
    This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

    Read the article

  • Sharepoint Central Administration stuck / high CPU usage

    - by johnnyb10
    I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

    Read the article

  • Suddenly getting lock timeouts with MySQL

    - by Marc Hughes
    We've got a web app hosted on Amazon Web services. Our database is a multi-az RDS MySQL server running 5.1.57 and 3-4 app servers talk to it. Today, we started seeing a lot of errors along the lines of "Lock wait timeout exceeded; try restarting transaction" - almost 1% of POST requests are seeing this. There have been no modifications to the code running on the site. There have been no schema changes. We haven't had a big spike in traffic. I've been looking at the processes running, and none seem out of control. I tried scaling our RDS instance from a small to a large, with no effect. Two days ago, Amazon had some outages. As part of the recovery from that, our RDS server, and our app servers ended up in different availability zones, but all within the same region. But yesterday, everything was fine so I'm not convinced that's related. The lock timeouts are in different types of requests and occur in different InnoDB tables. I have noticed the number of open connections jumped when we started seeing problems, but they may be a symptom and not a cause. What are my next steps in debugging this?

    Read the article

  • Large, high performance object or key/value store for HTTP serving on Linux

    - by Tommy
    I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >