Search Results

Search found 4863 results on 195 pages for 'mind bending'.

Page 133/195 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Using multiple USB webcams in Linux

  - by rachelderp

  Running more than one USB webcam in Debian/Linux results in the the following error: libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON: No space left on device What initially seemed to be a programming issue in OpenCV turned into a quest for a mysterious hardware/software problem after the same errors were produced by running cheese and xawtv. Apparently it's caused by webcams requesting all the available bandwidth on the USB host controller. With that in mind I decided to run wireshark and capinfos to see just how much bandwidth a single camera used. 4 megabits per second at 320x240 14 megabits per second at 640x480 32 megabits per second at 1920x1080 Interesting! That might explain why two cameras at 320x240 work but any higher resolution fails. It's as if my USB controller is only operating at USB 1 speeds, yet lsusb shows both webcams belonging to a device which supposedly supports 480 megabits per second. One solution proposed forcing the webcams to calculate their bandwidth usage instead of requesting their maximum by running the following commands: sudo rmmod uvcvideo sudo modprobe uvcvideo quirks=128 Unfortunately that made no difference, so I decided to try another solution. A post on StackOverflow suggested telling my webcams to use a lower FPS or compressed video format like MJPEG, but after running v4lctl list it doesn't appear either of my webcams support changing their video mode. And that's where I'm stuck. Why would two webcams operating well below the maximum speed of USB 2 would produce this error? ps: It's not a disk space issue, df displays no change when the webcams are started. pps: If it makes a difference, here's the output of lsusb

  Read the article

• Install Peppermint OS three on Asus EeePC

  - by Kithoth

  I just had a new Asus EeePC R051CX. Out of the box, the installed OS is Ubuntu 12.04 LTS, but I am trying to install Peppermint OS three (as single boot). Problem. Once on live CD (well, live USB stick...), I'm in trouble in both following situations: Try Peppermint OS Live In this case, the first thing I get is a message reading The system is running in low-graphics mode Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself. I can solely press "return" to accept, then I have a list of 4 options to answer the question "What would you like to do?". But I simply can't do anything at this moment, except switching to console mode or rebooting (keyboard / mouse controls don't allow me to do anything else). Install Peppermint OS Something I really don't understand... it launches the Ubuntu Recovery Media (which was already installed when I received the device)! Also, it says in the bottom ERROR: This recovery media only functions on Ubuntu systems. All I can do is quit (that is, reboot). One last important thing that comes to my mind: this stick worked just fine on the other computers I've tried it on. I really hope someone could bring me the light, a friend of mine told me how cool this OS is for EeePCs. Don't want to give up! Thanks. Edit I finally could install Peppermint, but not by understanding why I couldn't do it the logical way. Instead, I reinstalled Ubuntu myself (erasing the factory one). Then, I could simply boot on my live USB and perform a fresh install of Peppermint. So, I still don't know how and why the mentioned problem occurred.

  Read the article

• Windows 7, enabeling IE for removal

  - by Thew

  For a while now, Windows Update has been prompting me to update IE9 to IE10. And every time I turn off my PC, It starts to install that one update wich allways fails. Why does it fail updating IE9? I don't know. So the solution I had in my mind was to remove IE9 and then install IE10 manually. THe problem is now, I can't find the uninstall file for IE9. I have looked in windows control panel / programs and features but it didn't show up, not even in the installed updates section. So after I clicked on Turn windows features on or off, I saw that the IE9 box wasn't checked. So I checked it, clicked OK, but then when I clicked on the Turn windows features on or off link again, it wasn't checked anymore. It's almost like Windows doesn't want me to uninstall IE9. but I have to in order to normally shut down my pc, because everytime I shut my PC off, it tries to install that stupid update again! What can I do to solve this?

  Read the article

• How to set up multi users on dev server with git and github

  - by Derek Organ

  I'm working on lamp application. We have 2 servers (Debian) Live and Dev. I constantly work on dev main to add new features and fix bugs. When happy all works well I scp the relevant code to the Live system. Database (mysql) is local to each machine. Now this is pretty basic setup really and I want to improve the workflow a bit. I use git and github for version control. Admittedly I've only really used one branch. Their can be 3 different developers who work on the code at different times. We all use the same linux username to connect to the dev server and edit the code directly when needed. I usually then commit and push the code at the end of the day to github. One thing to bare in mind is it isn't easy to run this code on a local machine as there are many apache and subdomain configurations that wouldn't work on a local machine so it is important to work on the dev server not locally. I need to create a new process because we need to have a main trunk now and a branch with a big code re-write. What is the best way to do this. Should I create different unix logins for each developer and set up different working areas on the dev server for there changes? e.g. /var/www/mysite_derek /var/www/mysite_paul /var/www/mysite_mike my thinking is they can do a pull from the main branch and then create there own branch and merge it back in. I'm not sure how this will work though with git locally and with github. will i need to create different github user accounts as well. I'd like to do this the 'right' way and future proof for having lots of potential developers but I also don't want to over complicate it. I simple and elegant solution is preferred. any recommendations or suggestions?

  Read the article

• File exists but is unreadable by PHP

  - by Aron

  More than once I have ran into this issue: I have a cache file that is automatically generated by PHP. It contains some generated PHP code. However for some reason the file cannot be read and parsed by PHP. These are the symptoms: File actually exists on file system. Using Terminal you can navigate to the file, view its contents (which are fully intact), etcetc. PHP file_exists() will report that the file exists...which is correct since it does :) Then I include() the file. But when actually parsing the file, PHP will just consider it an empty file. No fatal error, just no PHP code actually executed. Again, its as if the file was completely empty (which I assure you, it is not)... It is not a permissions issue. Permissions are set as needed. Workaround: open the file in Terminal via 'nano' or some other text editor and just save it to the disk again. After that (despite no changes to the content) PHP will run it just fine... As a clarification, I'd like to add that this happens rarely, but frequently enough to be a problem. And even when it does, there are hundreds of other similar files on the same system that work without a problem... If this were an issue affecting only my own scripts, I would consider that there must be a bug in the way I generate the PHP code. But no, the issue has occurred more than once when deploying to a server (usually from Beanstalk repository via FTP). The issue has been present on various servers, Debian and Ubuntu running Zend Community Server. Any ideas? One that crossed my mind was opcode cache-ing (part of Zend Server CE)...could it be that an empty version of the file is cached if it is requested while the write operation is still in progress?

  Read the article

• How to convince Out of state resume filtering?

  - by sanksjaya

  Hello folks! Personally I've applied to quiet a handful of IT admin jobs inside my state and to the ones that are way far away. The sad part is I never miss to get an interview with the jobs in my state, but get a call once in a blue moon from jobs out of my state. Note: All the jobs are of similar nature. Recently one of my friends told me that "Applicants with local addresses are the ones that are even looked upon". How true is this? Does filtering take place at address level before qualifications? Is using a PO box on resume acceptable [one for each state like CA, TX, VA]? Any other suggestions to get calls from out of state? Thank you :) [wiki] =================== EDIT: Ignore my previous questions. PO box is out of my mind. So changed the title. Here are my new questions: 1. How true is this? Does filtering take place at address level before qualifications? 2. I'm ready to relocate anywhere on my own (Time/Money). How do I convince out-of-state resume filtering HR's? Sanks

  Read the article

• Transfer iptables rules to another server (almost) real time

  - by MrShunz

  I'm running 2 cPanel servers with ConfigServer Security & Firewall plugin. One of the functions of the plugin is to block via iptables (temporarily and/or permanently) IPs which fail various authentications (POP3/IMAP, SMTP, FTP, webmail, mod_security and such). Now, i'd like to push those IP blocks to the border router to drop packets as soon as possible (and doing so protecting the other machines on the network). Keep in mind that after N failed logins IP is blocked for 5 minutes, then re-allowed. If multiple bans occours in an hour IP is blocked permanently and should be unlocked "by hand". So I need a near realtime solution. What I'm looking for is a better way than firing some cronjobs both on cPanels and border router to: dump the rules to file transfer the file to border router (via scp/sftp) load the rules from the file in the border router I'm aware that I will need some scripts to parse and modify the rules as cPanels have one ethernet interface and some aliases while border router has two ehternet interfaces and some loopbacks. All machines involved use Linux. EDIT as per @pjmorse comment. The plugin consists of a bunch of perl and config files. The part I'm intrested in is a process which scans logfiles (lfd) and installs iptables rules (and sends an alert email). Fact is, it upgrades quite often (one or two times a week) and itself is 7000 lines of perl so I'm not comfortable on tampering with it.

  Read the article

• Windows 7 Laptop Randomly Sleeping

  - by Josh Arenberg

  I'm running Windows 7 64-bit on a Lenovo laptop, and I have a problem wherein after I've put it to 'sleep' once, it will seemingly without any reason or warning go back to sleep every 10 to 15 minutes after that. Each time it wakes back up just fine, and you can happily continue on. However, 10 or 15 minutes later, it just drops out into sleep mode. I don't see any errors in the system logs. I don't think it's related to heat ( since it's not rebooting ). When I check the system event log, I can see where the machine goes to sleep, but it simply says "reason: application API", and doesn't indicate which app ( brilliant ). I don't see any errors from hardware or anything relating to sleep in the application log that would point to what is going on either. How can I find out which app is triggering this? EDIT: I confirmed that temperature wasn't the issue. I think it's important to keep in mind that this condition only happens after the first sleep. If I reboot, the problem goes away until I put it to sleep, after which it sleeps on it's own every few minutes. Is there no way to capture which app is calling the sleep routine?

  Read the article

• Minecraft server hosting hardware specifications [on hold]

  - by Andrew Wright

  I am planning on purchasing a server to rent off Minecraft game servers, largely to friends. I am planning on purchasing a 128GB RAM server to save on colocation costs (as I am likely to need more than 32GB and would have to rent 2U of space...) I am hoping for some advice about the processing power needed to deal with this level of RAM. The servers will be run in a shared environment on linux in a VM to make backups easier. The server I have in mind is dual CPU. I have been considering at the low end dual Xeon E5-2609V2 Quad-Core 2.5Ghz, and at the high end dual Xeon E5-2650V2 Eight-Core 2.6Ghz. The difference between these is 6.4 GT/s and 8 GT/s and £3000 for the lower spec server, £4300 for the higher spec. I was hoping I could get advice about whether it is worth paying for the extra/higher speed processor or if I would be wasting my money? Thank you for any help - I appreciate that this is not directly related to professional system administration.

  Read the article

• Server specification recommendation

  - by foo

  To cut the story short, I can't buy an item (server/cpu/motherboard/ram) that costs more than USD 330. However, I can combine them, meaning, I can buy a CPU that costs USD 330 and motherboard that costs USD 330. With this limitation, I can't buy a powerful 1U server which will definitely costs me more USD 330. With that in mind, I was hoping to build a powerful desktop PC which will be used as a database server. However, through my experience, desktop PC doesn't last very long, usually the motherboard will just die by itself after 1 or 2 years. So, what would you guys recommend me to buy with this kind of budget? Every item must be <= USD 330. Will be used as a MySQL server. RAID would be nice. 1TB is pretty big for my data. I do not need external graphic card (onboard would do just fine), mouse, keyboard, monitor. Linux friendly. One ethernet port is good enough. It's important that those hardware is made of components that will last long (at least 3 years or something). The server will be placed in an air conditioned room, but a good ventilation for the server is always preferred. I won't overclock it. Intel processor is preferred. Thanks in advance.

  Read the article

• How to prevent the command prompt from closing after execution?

  - by Sk8erPeter

  My problem is that in Windows, there are command line windows that close immediately after execution. To solve this, I want the default behavior to be that the window is kept open. Normally, this behavior can be avoided with three methods that come to my mind: Putting a pause line after batch programs to prompt the user to press a key before exiting Running these batch files or other command line manipulating tools (even service starting, restarting, etc. with net start xy or anything similar) within cmd.exe(Start - Run - cmd.exe) Running these programs with cmd /k like this: cmd /k myprogram.bat But there are some other cases in which the user: Runs the program the first time and doesn't know that the given program will run in Command Prompt (Windows Command Processor) e.g. when running a shortcut from Start menu (or from somewhere else), OR Finds it a little bit uncomfortable to run cmd.exe all the time and doesn't have the time/opportunity to rewrite the code of these commands everywhere to put a pause after them or avoid exiting explicitly. I've read an article about changing default behavior of cmd.exe when opening it explicitly, with creating an AutoRun entry and manipulating its content in these locations: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Command Processor\AutoRun HKEY_CURRENT_USER\SOFTWARE\Microsoft\Command Processor\AutoRun (The AutoRun items are _String values_...) I put cmd /d /k as a value of it to give it a try, but this didn't change the behaviour of the stuffs mentioned above at all... It just changed the behaviour of the command line window when opening it explicitly (Start-Run-cmd.exe). So how does it work? Can you give me any ideas to solve this problem?

  Read the article

• Things to consider when building a continuous integration server?

  - by Dave

  I'm new to continuous integration, but immediately realize its value, and I want to get one set up right away. I have played with TeamCity and have it working in a VM great. Now, I don't want to spend money on another system, so I was planning on just doing the VM again on a faster machine (i.e. my dev system). There are a few questions that come to mind with this: Hard disk allocation - how big should it be? Sure, 60GB seems like more than enough, but people also used to think that we'd never need more than 64KB of RAM Backups - is it even important to back up the integration server? Sure, I guess it's nice so that one doesn't have to go through the entire configuration process again, but I would think that's about it. I could snapshot my VM every time I do a configuration change, and then do a backup of applications only (ignore the buildAgent stuff). Migration - if I want to go away from a VM on my dev system, to a new server, which maybe even runs Windows Server 2003, is it easy enough? Perhaps this is a particular point best suited for StackOverflow.

  Read the article

• Windows 7: moved system partition, need to update boot partition

  - by Actorclavilis

  So, I have a decently standard Windows7/Ubuntu dual-boot setup, and (since Ubuntu is my usual operating system) I found I needed to grow my Ubuntu partition and shrink my W7 partition. Originally, my system (500G) looked like this: W7 Boot Partition (1.5G) Ubuntu (around 240G) W7 (same as Ubuntu) (on an extended partition, all by itself) Swap (rest of disk, around 16G) Now I'm no stranger to partitioning and filesystem tools, especially GParted, which I used on a Linux boot disk. After my partition editing, the partitions are laid out the same, except the Ubuntu partition is now 407G and the W7 partition is smaller to compensate. I had supposed, based on http://www.gparted.org/faq.php, that I would be able to run the W7 install disk in recovery mode and have it deal with the rearrangement, then possibly reinstall GRUB or something. Well, now the W7 install disk doesn't even see my W7 installation. All my files are there, the NTFS is perfectly clean, no problems there, but the install disk won't notice it. (Of course, the GRUB entry works fine but the W7 boot partition (which I didn't change) refuses to boot it.) So, basically, any ideas on how to fix this? I don't especially want to rerun the entire install procedure because I'll have a bunch of programs to reinstall (never mind redoing GRUB), but I fear that might be the only option. Thanks.

  Read the article

• How to prevent response to who-has requests on virtual eth interface?

  - by user42881

  Hi, we use small embedded X86 linux servers equipped with a single physical ethernet port as a gateway for an IP video surveillance application. Each downstream IP cam is mapped to a separate virtual IP address like this: real eth0 IP address= 192.168.1.1, camera 1 (eth0:1) =192.168.1.61, camera 2 (eth0:2) =192.168.1.62, etc. etc. all on the same eth0 physical port. This approach works well, except that a specific third-party windows video recording application running on a separate PC on the same LAN, automatically pings the virtual IPs looking for unique who-has responses on system startup and, when it gets back the same eth0 MAC address for each virtual interface, freaks out and won't allow us to subsequently manually enter those addresses. The windows app doesn't mind, tho, if it receives no answer to the who-has ping. My question - how can we either (a) shut off the who-has responses just for the virtual eth0:x interfaces while keeping them for the primary physical eth0 port, or, in the alternative, spoof a valid but different MAC address for each virtual interface? Thanks!

  Read the article

• Enterprise level Ticketing and inventory system reccomendations [closed]

  - by TrackingSystem

  My company is sort off at a stand still when it comes to our technician ticketing and inventory system. We currently use Numara TrackIt! - which isn't cutting it to say the least. Dell recommended KACE, but it's web based which is what we would like to avoid. We need a good ticketing and inventory system with the following: Server/Client setup Client supports XP/Windows 7 Ent. Web Based as well as Client is a plus Technician ticketing Active Directory integration Inventory System (Asset tag tracking etc/PO tracking) Exchange integrated - when tickets are made you have an option to send to the requester. Something that will scale well Please, if anyone is a Systems Admin or has knowledge regarding use of a great ticketing system please let me know. We have a large international corporation - price honestly isn't an issue. Keep in mind this will be mainly used for technicians to create tickets, enter inventory(track PCS) and possible even an option to track purchase orders. We want an enterprise level ticketing system with these capabilities please help! Thank you.

  Read the article

• Data recovery on working hard drive

  - by emgee

  So I have a 5 bay hot swap SATA enclosure that's connected to a Silicon Image-based SATA adapter in a computer. It's running XP Pro. There are two 1.5TB hard drives in slots 1 and 2 respectively, set up using RAID 1 using the the Silicon Image utility. There are also two 1TB drives in bays 3 and 4, also set to RAID 1 the same way. The partitions for both RAID arrays are Dynamic partitions. A few days back, there was a bare hard drive that needed some files copied off of, so it was popped it in bay 5, that bay to pass-through, and the copied data off of it. Later, I noticed that my 1.5TB drives no longer showed up in windows. In the Silicon Image utility, the drives showed up fine, no error. However, in Device Manager, it shows the RAID 1 array as uninitialized. It shows up as the right size, etc., but nothing else. There's no sign of anything wrong with either drive, so I'm not sure what happened exactly. I'm not the only one who has access to that computer, so it is possible there is something else done to it that I don't know of. There's quite a lot of data on it still, and if at all possible, I'd prefer to not send it to Ontrack. Does anyone know of software that would restore the partitions, keeping in mind that it's a Windows LDM partition? I have access to a variety of Operating Systems, so something that would work on Mac, Windows or Linux would be acceptable. The programs I usually use are not compatible with LDM.

  Read the article

• Matched or unmatched drives for RAID arrays?

  - by Will

  Looking around there is conflciting information on this, with some strongly suggesting one or the other. From my understanding the issue with matched drives is that the wear on both drives is more or less the same, so the potential for the second drive failing with or very soon after the first is pretty high. People also claim matched drives give substianatally higher performance however assuming the unmatched drives are more or less the same (eg 2, 1 TB STATA II 7200rpm drives with 32MB cache), would the minor differences between say a Seagate and a Western Digital one (say one has a 128MB/s read rate, and the other a 150MB/s read rate, as well as I guess various other minor differences) actually cause any notable performance loss, ie potentialy worse than two matched 128MB/s drives, or does RAID not really care and give you essentially an optimal solution (eg upto 278MB/s total read speed for RAID 0 and 1) and similar for other RAID with more "unmatched" drives (5 and 1+0 come to mind as possibilities)? Also I couldnt find much info on how this is different on different RAID setups, eg RAID 0 or RAID 1, software or hardware RAID, etc. I'm assuming such things have an effect, and thats it's not all the same for RAID in general?

  Read the article

• Verizon overbilling me ?

  - by bek

  I have verizon air card for my internet. Which is called vz manager. I have had it for about a year. Keeping within my usage allowance the whole time until 3 months ago, when my bill came in my 5,000 g allowance was ran to 18,000. It has continued to do so through the last 3 months. My usage reset itself yesterday for the new month. I got on google for about 5 minutes and chatted for about an hour yesterday online. Mind you that I have never done anything any different then i do everyday. I do not download music or watch videos on my computer, nothing like that. Well since last night a 8 pm my usage sayd 1109.525 gb. ALREADY! For being on the internet for an hour with no downloads. What could be causing this, please thrown me some ideas. Verizon is checking on the problem, but that usually doesnt get me the answer i want. Can someone be hacking my card and using internet through it, has told me that that is not possible, however I think with the internet anytihng is possible.

  Read the article

• Best SSD tweak for Windows 7

  - by Nick Berardi

  I have seen many articles about tweaking an SSD, but many of them seem outdated, or too broad (read all Windows XP, Vista, and Windows 7 general tweaks). And I know that Windows 7 has been specifically tweaked for SSD by the Windows team, so I don't want to do something that was written for Windows XP in mind and end up circumventing something the Windows team has specifically designed in to Windows 7. So my question is what are the best SSD tweaks for Windows 7 that you have found to get the performance out of your drive? I hope to make a comprehensive list in the answers below so there won't be so much disinformation in the forums about what to do and what not to do. Here are a few that I see posted up on the forums alot: Disabling Superfetch. Yes or No Disabling Page File or limiting it to a really small size such as 500 MB. Disabling Indexing. Yes or No Disabling Defragmenting. Yes or No What are your thoughts do you have any that have worked for you? When providing an answer please do your best to back it up with a reason and possibly some documentation from MSDN, TechNet, or another credible source.

  Read the article

• Shell replacement for kiosk environment with desktop icons

  - by tuesprem

  I have to deploy around 80 touch-screen terminals for my company. We're going to run several Windows applications on those terminals and they'll be operated by touch input only. I basically want those machines to run in a kiosk mode, so employees won't be able to launch any programs than the ones they're supposed to (also, this will hide the task bar/start menu, which will give it a much nicer, corporate look). There's usually one app that should automatically launch on startup and other apps that can be launched from the desktop. I've tried to accomplish this (under Windows 7 Pro) with a custom shell replacement. This removes the task bar/start menu like I described earlier. I used an AutoHotKey script for this, because it's easy to, for instance, define hotkeys so admins will still be able to launch stuff like Windows Explorer (okay, I know I could just launch it from the task manager [Ctrl+Shift+Esc] but I'm considering locking that as well). So far so good. Some problems though: No desktop icons. Needed to launch apps from the desktop. No wallpaper. Required for CI. Is there any way around this? I wouldn't mind using another shell replacement, as long as it's reasonably lightweight. I'd love to get the wallpaper and desktop icons to show with something like AutoHotKey though. Thanks!

  Read the article

• VzAccess Manager.

  - by bek

  I have verizon air card for my internet. Which is called vz manager. I have had it for about a year. Keeping within my usage allowance the whole time until 3 months ago, when my bill came in my 5,000 g allowance was ran to 18,000. It has continued to do so through the last 3 months. My usage reset itself yesterday for the new month. I got on google for about 5 minutes and chatted for about an hour yesterday online. Mind you that I have never done anything any different then i do everyday. I do not download music or watch videos on my computer, nothing like that. Well since last night a 8 pm my usage sayd 1109.525 gb. ALREADY! For being on the internet for an hour with no downloads. What could be causing this, please thrown me some ideas. Verizon is checking on the problem, but that usually doesnt get me the answer i want. Can someone be hacking my card and using internet through it, has told me that that is not possible, however I think with the internet anytihng is possible.

  Read the article

• What are the ways to build a failover cluster?

  - by light

  I have a task where I need to build a failover cluster in two cases: first with servers on Red Hat Enterprise 5.1 and second with SUSE Linux Enterprise 11 SP1. Both cases have SAN. I know there are many ways to build failover cluster, but I can’t find out more, so I need next: The ways to build it? I know only virtualization. Any good book or resource to broad my mind? I’ll be glad to hear any suggestion. Thanks! EDIT #1: failover of servers with bussiness application on it. EDIT #2: will be great to hear summary about solutions with SLES servers? EDIT #3: So if I understand correctly, in my cases the main ways are to use internal solutions or virtualization. So now I have additional questions: Does manufacturer of blades provide some solution? For example HP or IBM. (Without virtualization) Do I need additional server to control "heartbeat" between main and redundant servers? (Virtualization) For example I have several physical servers with VMs. Do I need additional server to control availability of VMs and to move VMs to another physical server in the case their physical server failure? Sorry for my poor English. EDIT #4: Failover of VM or OS on physical server. In both cases will be used SAN , it's not specified, but I think with file system image on it. I started to think that my question is stupid and I need to remake it.

  Read the article

• How to format my external HDD back to as "removable storage"?

  - by user990106

  Recently I formated my Seagate FreeAgent GoFlex external HDD in Mac OS X using GUID partition table since I wanted to install another Mac OS X onto that external HDD. However I changed my mind after my external HDD being formatted. Now I want to format my external HDD back to NTFS so that I can use it with my Windows 7. However, after I connected my external HDD via USB it didn't show up in my "computer" so I used "Disk Management" to check what's wrong with it. In the "Disk Management" I saw that there was one partition of my external HDD called "EFI partition" and I found that I could not delete this partition in the "Disk Management". So I tried to use "diskpart" in cmd and select the external HDD and commanded "clean". Then the EFI partition was gone and I created new volumn on that external HDD. However, after the volumn being created my external HDD did show up in my "computer" but it is in the "Hard Disk Drive" not in the "Devices with Removable Storage" as it used to be. I'm wondering if I can do anything to it to make it recognized as a "Devices with Removable Storage"?

  Read the article

• Allow more websocket connections

  - by Switz

  I want to load balance my node.js (DerbyJS to be specific) application on a basic Linode (512MB ram). It can probably take more than one process running at once. The querys/database does not concern me as I'm not doing anything intensive. The problem at the moment is that it can only handle up to ~40 websocket connections at once. I would love if I could get that number in the few hundred+ range. I anticipate a lot of traffic on launch due to the fact that it's a highly niche community with an engaged audience, but after it should be fine with just ~20-40 connections at once, which it handles perfectly as of now. I don't mind spending a bit of money for a week or two worth of running, but I also don't want to switch production environments. How can I test the process to see how many instances I am able to run on the box? Will increasing the number of processes increase the amount of websockets I can handle, or is that a limitation of the server's network? I have an old Macbook Pro running Linux sitting next to me that has 2GB ram and a 2.8 Dual Core Processor. Could I use this to handle some of the extra load? I could probably load balance with nginx to its IP. I'm on a FiOS home network. If you have any suggestions, I'd really appreciate it. Thanks

  Read the article

• What are the side effects of disabling an Exchange mailbox?

  - by Nic

  When working with Exchange Server 2007 or newer, disabling a mailbox is a fairly common operation. However, the Technet documentation has no details about the side effects of disabling a mailbox. This is all it says. "This task removes all the Exchange attributes from the user object in Active Directory. Based on the deleted items retention policy, the Exchange store will retain mailbox data for the user object." Source: http://technet.microsoft.com/en-us/library/bb123730(v=exchg.141).aspx But is that all? Exchange mailboxes in the real world tend to be highly interconnected. Perhaps the boss has delegated calendar control to a secretary. Maybe a team of staff members all share access to a public folder. Perhaps a power user has been granted the ability to receive email at several different addresses. Two clear questions come to mind. What happens to links between mailboxes after a mailbox is disconnected? Can the Disable-Mailbox operation be easily undone?

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >