Search Results

Search found 16894 results on 676 pages for 'block device'.

Page 134/676 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

• centos 6.3 kvm external ip forwarding to guests

  - by user1111702

  I have a centos 6.3 server with kvm installed. The server has 4 external ips and one NIC. 176.9.xxx.xx1 176.9.xxx.xx2 176.9.xxx.xx3 176.9.xxx.xx4 I use the following configuration ifcfg-eth0 as slave to ifcfg-br0 the configuration in ifcfg-eth0 is DEVICE=eth0 ONBOOT=yes BRIDGE=br0 HWADDR=14:da:e9:b3:8b:99 and in the ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static BROADCAST=176.9.xxx.xxx IPADDR=176.9.xxx.xx1 NETMASK=255.255.255.0 SCOPE="peer 176.9.xxx.xxx" and I have 3 more aliases for br0 , br0:1 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx2 NETMASK=255.255.255.248 ONBOOT=yes br0:2 to get the trafic from the third external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx3 NETMASK=255.255.255.248 ONBOOT=yes br0:3 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx4 NETMASK=255.255.255.248 ONBOOT=yes The above settings work fine and I recieve the trafic from all the external ips. My problem is that I want to pass the trafic from external ip to specific virtual guest on my server. ie trafic that comes from 176.9.xxx.xxx2 must pass to virtual machine 1 176.9.xxx.xxx3 must pass to virtual machine 2 176.9.xxx.xxx4 must pass to virtual machine 3 Can you please help me how to achieve this ? What are the settings on the host and what should I do to the guests. Thank you in advance

  Read the article

• Nginx: Maintenance page and localhost access

  - by ian.evans

  As I prepare to test some changes, I thought I'd set up a maintenance page block so I could do the testing. Just realized though that the maintenance block examples for nginx take the site down for everyone. How do you serve the maintenance page to visitors will still allowing localhost access. Should I just create a new server block listening on another port and deny all, allow 127.0.0.1?

  Read the article

• Graphic driver for Targa Now NT9231

  - by Lumio

  I thought of installing Xubuntu on my elder Targa Now nettop and didn't think about the driver option. So now I'm here with a fresh Xubuntu installation and looking for graphic drivers. I found someone who might have had a "good" result with SiS - and the package is already installed, but I can't get my xorg.conf right. This is how my xorg.conf looks like right now: Section "Device" Identifier "Configured Video Device" Driver "sis" EndSection Section "Monitor" Identifier "Screen 0" Modeline "1024x768_60.00" 64.11 1024 1080 1184 1344 768 769 772 795 -HSync +Vsync #HorizSync 30.0-62.0 #VertRefresh 50.0-70.0 EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1024x768" "800x600" EndSubSection EndSection Thanks for every help given!

  Read the article

• How can I combine code from an old revision when I didn't branch in TortoiseMerge?

  - by gr33d

  I need to combine (merge?) some parts of an old revision with a newer revision of a file. I'm still pretty new to subversion, so I'm not sure what I'll bomb in the process. I did not branch--these are simply different revisions of a file. How do I send the sections of code from r1 to r3 where they are needed. The keyboard shortcuts and menu options for "theirs", "mine", "left block", "right block", etc aren't very intuitive. If I need 5 blocks from r1 to be after the first 10 blocks of r3, how do I do it? Shouldn't I be able to go through r1 block by block and decide if and where it belongs in r3? Thanks in advance!

  Read the article

• UUID in Mountain Lion

  - by Naji

  I am trying to find my external HDD UUID in Mountain Lion but diskutil info /dev/disk1s1 returns: Najis-MacBook-Air:~ ****$ diskutil info disk1s1 Device Identifier: disk1s1 Device Node: /dev/disk1s1 Part of Whole: disk1 Device / Media Name: Untitled 1 Volume Name: My Book Escaped with Unicode: My%FF%FE%20%00Book Mounted: Yes Mount Point: /Volumes/My Book Escaped with Unicode: /Volumes/My%FF%FE%20%00Book File System Personality: NTFS Type (Bundle): ntfs Name (User Visible): Windows NT File System (NTFS) Partition Type: Windows_NTFS OS Can Be Installed: No Media Type: Generic Protocol: USB SMART Status: Not Supported Total Size: 2.0 TB (2000364240896 Bytes) (exactly 3906961408 512-Byte-Blocks) Volume Free Space: 212.5 GB (212506509312 Bytes) (exactly 415051776 512-Byte-Blocks) Device Block Size: 512 Bytes Read-Only Media: No Read-Only Volume: Yes Ejectable: Yes Whole: No Internal: No And there is no UUID. What is wrong exactly? Thank you.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Problems with 5.1 digital out on Ubuntu 12.04

  - by user895319

  I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

  Read the article

• Windows Phone 8 not interfacing with Zune software

  - by Cyberherbalist

  I just got a Lumia 521 with Windows Phone 8 and am trying to get the device to work with the Zune software on my PC. I still have my Windows Phone 7 device, and the new one is not working the same way. When I plug the WP7 device into the PC's USB port, it automatically fires up Zune and I can sync my podcasts and music etc to the device. But when I plug the Lumia into the PC it doesn't fire up Zune, and if I start Zune manually, it doesn't interface with the phone at all. Perhaps I am missing something and WP8 isn't supposed to use Zune to interface with the phone?

  Read the article

• Computer wakes itself few seconds after hibernation

  - by Juan Zamudio

  Hi all, this is the situation, this is a Dell Optiplex 755, I recently upgraded it to Windows 7 64 bits, it had Windows XP SP3 previously, on XP I never had a problem hibernating the PC, now with Windows 7 64 every time I hibernate the PC it wakes it self after 5 or so seconds. Here are the steps I already tried: On Windows 7 I enabled the hibernation following this steps In the MoBo the sleep settings are on S3 In the Mobo I disable remote wake ups I have disabled the remote wake up in the NIC When I run the lastwake command I get unknown device or something like that I already disable the wake timers on Windows I have the latest drivers from Intel, but I just found out that in the device Manager I get a warning sign on the "Intel AMT SOL (COM3)" device saying that it failed and windows stopped the device, I reinstalled the Intel drivers but nothing changed. The only thing that I haven't touch is Intel ME in the MoBo but I don't if that could help and what settings are correct. Thanks for you help.

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• Netgear Router missing Wireless Configuration Menu Link

  - by ccisystems

  I have a Netgear WiFi router DG834G v3. On it it says it's a WiFi, ADSL 2+ modem, switch, etc. There is an antenna on the back and a WiFi indicator on the front. However, when I connect to it via the web interface, the wireless setup link is missing from the menu. The top label indicates it is a DG834 (without G). I have received it from a friend and was really looking forward to using it but I really need the WiFi part. I looked on Netgear's site as I thought someone must have uploaded the wrong firmware for the device sometime - so I upgraded to the latest firmware, but it still says it's NOT a 'G' device and the wireless menu is nowhere to be found. I'd appreciate a push in the right direction as to what I could do. Is it possible that the WiFi chip is broken or something and the device does not detect it and the firmware reverts the device to a different version?

  Read the article

• How to log kernel panics without KVM

  - by Spacedust

  My server is crashing and I can't find an answer why. It all started after my datacenter upgrade RAM from 16 GB to 32 GB. I also found such logs in dmesg - they've started to show itself just before the first kernel panic: EXT4-fs error (device md2): ext4_ext_find_extent: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_ext_remove_space: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 20974: 8589 blocks in bitmap, 54896 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. EXT4-fs error (device md2): ext4_ext_split: inode #97911179: (comm pdflush) eh_entries 28769 != eh_max 26988! EXT4-fs (md2): delayed block allocation failed for inode 97911179 at logical offset 1039 with max blocks 1 with error -5 This should not happen!! Data will be lost EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 21731: 5 blocks in bitmap, 60762 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. My system is CentOS 5.8 64-bit with latest kernel 2.6.18-308.20.1.el5. How can I check what is the reason of kernel panic without having an access to the KVM ? I have told my datacenter admins to check the memory in the server.

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated. Current Solution I found a solution to my problem, but I am not sure that this is the actual way to do it. Having a closer look at my raid I found that sdb5 was always listed as a spare device: mdadm --examine /dev/sdb5 [...] Number Major Minor RaidDevice State this 2 8 21 2 spare /dev/sdb5 0 0 0 0 0 removed 1 1 8 5 1 active sync /dev/sda5 2 2 8 21 2 spare /dev/sdb5 so readding the device sdb5 to the array md3 always ended up in adding the device as a spare. Finally I just recreated the array mdadm --create /dev/md3 --level=1 -n2 -x0 /dev/sda5 /dev/sdb5 which worked. But the question remains open for me: Is there a better way to manipulate the summaries in the superblock and to tell the array to turn sdb5 from a spare disk to an active disk? I am still curious for an answer.

  Read the article

• Wacom Bamboo tablet and Linux: Anyone experience with it? On which level of abstraction is it suppor

  - by linux_is_for_desktop

  Hello! Does anyone has experience with this device under Linux? On which level of abstraction is the Wacom Bamboo tablet supported? Is the device input just translated to mouse input, so that every application can profit from it? Or do I need special (design|paint|...)-software which explicitely supports this device?

  Read the article

• install bluetooth in samsung R430, windows 7

  - by voodoomsr

  how can i install the bluetooth driver in this laptop in windows 7. The installation process tells me that i need to activate the bluetooth device to continue, but how can i activate if till that moment the device doesn't exist. There isn't any button or switch to activate the device manually. Edited: it's the np-r430 model. I read somewhere (a users forum, not official info) that for Chile and Argentina this models doesn't have built in the bluetooth device, but the US models have it. Maybe for some political and weird reason they send to south american laptops without that. The link of my notebook's specifications in an AR domain: np-r40

  Read the article

• Software for capturing still image snapshots from video input

  - by cantabilesoftware

  What software is available that will let me watch video from a USB video capture device at full PAL/NTSC resolution and capture a still image at a button press? More info: I'm using a KaiserBaas USB capture device (http://www.kaiserbaas.com/kaiser-baas-product-page/converters/video-to-dvd-maker), and want to capture screen shots from a PS2 connected to it. I'd like to play the game at the full PS2 resolution and capture certain scenes. The device has a one-touch snapshot button on it, but I can't seem to make it work and there's no mention of it anywhere in the documentation. The device works and the video appears in Power Producer (the included software), but I think it previews it smaller than the full resolution. I could print screen it, but having to crop will be a pain.

  Read the article

• HDMI Sound for HTPC

  - by Brent Arias

  I have the (perhaps) the same problem as stated in this other HDMI sound to HTPC question. I tried the advice of clicking on the speaker in the system tray. I can see the HDMI audio device I want to use. That device claims to be functioning properly. But there is no sound, and it won't let me select it as the active audio device. When I click on the troubleshooter, it says that there are no speakers connected. I would think this is because my computer us unable to pipe sound through the video card (preventing the HDMI from carrying it), except that it truly claims that it has an HDMI sound device that is working correctly. So I'm not sure what is wrong at this point. Thoughts? My system is Windows 7 x64. In case it makes a difference, the video card I'm using is this GeForce GTX 560

  Read the article

• Using Apache Environment Variables to set custom ErrorDocument

  - by Tad

  I've got a set of RewriteCond rules that test for various mobile devices and then set environment variables like "env=device:.iphone" or "env=device:.smartphone" if the useragent matches an iPhone or Android device. I'm trying to now redirect the user to custom-styled 404/500 server error pages for each device, by way of the error pages. Ideally I'd like to be able to test for a variable being there, and then write in a custom ErrorDocument string. But an apache doesn't seem to work in this case. Any ideas how I can construct if/else tests in an apache conf file for environment vars?

  Read the article

• Windows 8, NVIDIA graphics recognition fails

  - by Roy Grubb

  I just installed Windows 8 Pro OEM 64-bit (clean install) and it won't properly recognize my graphics adapter. When I installed Win8, it automatically installed the BasicDisplay.sys driver dated 6/21/2006. 6.2.9200.16384 (win8_rtm.120725-1247). Hardware - Mobo:MSi G41M-P33 Combo CPU:Intel CoreDuo 6600 Graphics:NVIDIA GeForce 9400GT *OS* - Windows 8 Pro 64-bit OEM The graphics adapter worked fine in Windows XP. The PC is a generic box, bought locally and its mobo failed recently, so I replaced it with the G41M. Microsoft wouldn't let me re-activate Windows XP with a different mobo, so I installed Win8, which appears to work except as described next. Win8 only partially recognizes the graphics adapter and won't allow NVIDIA latest driver installer to see that it's an NVIDIA card. As a result, OpenGL doesn't work, and this is needed by the software I most use. Other than that the graphics look OK. When I say 'partially recognizes', I mean that via the Control Panel, I can see that the adapter is described as NVIDIA, but the driver remains stuck at Microsoft Basic Display Adapter no matter what I try, including "Update driver..." in adapter properties. Display Screen Resolution Advanced Settings Adapter shows: Adapter Type: Microsoft Basic Display Adapter Chip Type: NVIDIA DAC Type: NVIDIA Corporation Bios Information: G27 Board - p381n17 Don't know what this means ... no mention of 9400GT Total Available Graphics Memory: 256 MB Dedicated Video Memory: 0 MB In fact the adapter has 512MB on-board video memory. System Video Memory: 0 MB Shared System Memory: 256 MB And Control Panel Device Manager Display adapters just shows Microsoft Basic Display Adapter. No other graphics adapter, and no unknown device or yellow question mark. What I have tried so far: 1. Cleared CMOS and reset. Updated BIOS and all mobo drivers as follows: 1st I used Driver Reviver to see if any driver updates were required. It found some but I didn't use that to get the drivers. Then I switched to MSi's own mobo driver utility Live Update 5. This also showed the board needed to update several so I used it to fetch the new drivers. After that it showed that everything was up to date and I checked with Driver Reviver again, which also reported no drivers now needed updating. Rebooted. Went to the NVIDIA site to get the latest graphics adapter driver. Their auto-detect "Option 2: Automatically find drivers for my NVIDIA products" said "The NVIDIA Smart Scan was unable to evaluate your system hardware. Please use Option 1 to manually find drivers for your NVIDIA products." So I downloaded 310.70-desktop-win8-win7-winvista-64bit-international-whql.exe, which lists 9400 GT under supported products, but when I run it, it says: "NVIDIA Installer cannot continue This graphics driver could not find compatible graphics hardware." Connected the display to the on-board Intel graphics (G41 Intel Express), removed the NVIDIA card and rebooted, changed to internal graphics in CMOS. Again it installs the MS Basic Display Adapter, and can't properly run my s/w that needs OpenGL. It runs on other machines with Intel Express graphics (WinXP and 7) Shut down and pulled out the power cord. Held start button to discharge all capacitors. Removed and re-inserted NVIDIA adapter in PCI-E slot and made sure properly seated. Connected the monitor to the card, screwed plug to socket. Reconnected power cord. Started and checked in BIOS that Primary Graphics Adapter was set to PCI-E. Started Windows. Uninstalled MS Basic Display Adapter in Device Manager. Screen blanks briefly, reappears. No Graphics adapter entry was then visible in Device Manager. Restarted PC. MS Basic Display Adapter Visible again in Device Manager. Clicked in Device Manager View Show hidden devices. No other graphics adapter appears, no unknown devices. Rebooted. Tried Scan for Hardware changes. None detected. Tried right-click on MS Basic Display Adapter Properties Driver Update Driver... Search automatically. It replied that it had determined driver was up to date. I checked that there were no graphic driver-related entries in Programs and Features that I could delete (none). Searched for any other drivers with nvidia in their name and deleted them, just keeping the 306.97 installer exe file. Did a Windows Update. Ran GPU-Z which shows (main items): Microsoft Basic Display Adapter GPU G72 BIOS 5.72.22.76.88 Device ID 10DE - 01D5 DDR2 Bus Width 32 Bit Memory size 64MB Driver Version nvlddmkm 6.2.9200.16384 (ForceWare 0.00) / Win8 64 NVIDIA SLI Unknown in the drop-down at the foot, "Microsoft Basic Display Adapter" is the only option If I swap hard disks in that machine to one with a Ubuntu 10.4 installation (originally installed on the same PC), lspci shows "VGA compatible controller as NVIDIA Corporation Device 01d5 (rev a1) (prog-if 00 [VGA controller])" and "kernel driver in use: nvidia" I'm out of ideas for new things to try and would be really grateful of suggestions. Thanks!

  Read the article

• Why change net.inet.tcp.tcbhashsize in FreeBSD?

  - by sh-beta

  In virtually every FreeBSD network tuning document I can find: # /boot/loader.conf net.inet.tcp.tcbhashsize=4096 This is usually paired with some unhelpful statement like "TCP control-block hash table tuning" or "Set this to a reasonable value." man 4 tcp isn't much help either: tcbhashsize Size of the TCP control-block hash table (read-only). This may be tuned using the kernel option TCBHASHSIZE or by setting net.inet.tcp.tcbhashsize in the loader(8). The only document I can find that touches on this mysterious thing is the Protocol Control Block Lookup subsection beneath Transport Layer in Optimizing the FreeBSD IP and TCP Stack, but its description is more about potential bottlenecks in using it. It seems tied to matching new TCP segments to their listening sockets, but I'm not sure how. What exactly is the TCP Control Block used for? Why would you want to set its hash size to 4096 or any other particular number?

  Read the article

• USB keyboard not working under Windows 7 x64?

  - by Comboo

  I have two USB keyboards, one no-name cheap thing and an old Logitech. When I plug them in to my computer they pop up in Device Manager as an "Unknown device" and "USB-receiver", respectively. Both of them fail to install any drivers, neither automatically or through Windows Update. Both keyboards work perfectly on another computer I have with Windows Vista 32-bit. Can this be one of those cases where a device does not work in a 64-bit version of Windows? I doubt it though since I've never had that problem before with any device and I thought that basic things like keyboards would be kind of failsafe. I don't really know how to start debugging this issue. I've tried all the obvious, rebooting, changing the USB port, etc. Are there any generic x64 keyboard drivers you can use? Is there any way to find the manufacturer of the keyboard over USB? There is nothing written on it.

  Read the article

• Looking for a new, free firewall (Sunbelt has a huge hole)

  - by Jason

  I've been using Sunbelt Personal Firewall v. 4.5 (previously Kerio). I've discovered that blocking Firefox connections in the configuration doesn't stop EXISTING Firefox connections. (See my post here yesterday http://superuser.com/questions/132625/sunbelt-firewall-4-5-wont-block-firefox) The "stop all traffic" may work on existing connections - but I'm done testing, as I need to be able to be selective, at any time. I was using the free version, so the "web filtering" option quit working after some time (mostly blocking ads and popups), but I didn't use that anyway. I used the last free version of Kerio before finally having to go to Sunbelt, because Kerio had an unfixed bug where you'd eventually get the BSOD and have to reset Kerio's configuration and start over (configure everything again). So I'm looking for a new Firewall. I don't like ZoneAlarm at all (no offense to all it's users that may be here - personal taste). I need the following: (Sunbelt has all these, except *) - 1. Be able to block in/out to localhost (trusted)/internet selectively for each application with a click (so there's 4 click boxes for each application) [*that effects everything immediately, regardless of what's already connected]. When a new application attempts a connection, you get an allow/deny/remember windows. - 2. Be able to easily set up filter rules for 'individual application'/'all applications,' by protocol, port/address (range), local, remote, in, out. [*Adding a filter rule also doesn't block existing connections in Sunbelt. That needs to work too.] - 3. Have an easy-to-get-to way to "stop all traffic" (like a right click option on the running icon in the task bar). - 4. Be able to set trusted/internet in/out block/allowed (4 things per item) for each of IGMP, ping, DNS, DHCP, VPN, and broadcasts. - 5. Define locahost as trusted/untrusted, define adapter connections as trusted/untrusted. - 6. Block incoming connetions during boot-up and shutdown. - 7. Show existing connections, including local & remote ip/port, protocol, current speed, total bytes transferred, and local ports opened for Listening. - 8. An Intrusion Prevention System which blocks (optionally select each one) known intrustions (long list). - 9. Block/allow applications from starting other applications (deny/allow/remember window). Wish list: A way of knowing what svchost.exe is doing - who is actually using it/calling it. I allowed it for localhost, and selectively allowed it for internet each time the allow/deny window came up. Thanks for any help/suggestions. (I'm using Windows XP SP3.)

  Read the article

• Canon HV20 recognized, but no drivers in Windows 7 x64

  - by Tuminoid

  My Canon HV20 camcorder is properly recognized when connected via Firewire to Windows 7 x64, but no drivers are installed for it. Windows or I cannot locate any drivers for it as, but it should be working off-the-shelf. I googled a lot, and found instructions to set IEEE 1394 host to legacy mode via Device Manager, but Windows doesn't offer me the legacy option at all. If I check the properties of Canon&HV20 device in Other devices section it says The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. It used to work just fine on my previous installation of Vista x64 and same hardware :/

  Read the article

• Passing multiple sets of arguments to a command

  - by Alec

  instances contains several whitespace separated strings, as does snapshots. I want to run the command below, with each instance-snapshot pair. ec2-attach-volume --instance $instances --device /dev/sdf $snapshots For example, if instances contains A B C, and snapshots contains 1 2 3, I want the command to be called like so: ec2-attach-volume -C cert.pem -K pk.pem --instance A --device /dev/sdf 1 ec2-attach-volume -C cert.pem -K pk.pem --instance B --device /dev/sdf 2 ec2-attach-volume -C cert.pem -K pk.pem --instance C --device /dev/sdf 3 I can do either one or the other with xargs -n 1, but how do I do both?

  Read the article

• A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

  - by user16654

  I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

  Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >