Search Results

Search found 3985 results on 160 pages for 'hd dvd'.

Page 134/160 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

• Acer Laptop does not power up after repairing DC power jack

  - by Misbah Mashkoor

  I have an Acer travelmate laptop which (by mistake) I dropped on the floor with the power jack side down, with the charger connected and it broke the DC jack from the inside of the laptop. Then I unscrewed the laptop and soldered the DC jack back and then plugged it in and switched on the laptop without the batteries. It did switch on, that was before screwing everything back. Then after assembling the whole thing back it does not power up. So I disassembled it again and just took the part which contained the DC jack (My laptop is like in two parts one contains the power jack which then sits on some pins on the main PCB) to a technician and he said that if you had connected this to a motherboard then it would have burnt cause the soldering was not right. And then I checked with my laptop again by connecting everything the light (the charging light) comes on when I connect the power but it does not switch on. Right now nothing is connected to the laptop; no HD, CD ROM, RAM , Battery. Nothing! Even then it does not power up. Any suggestions?

  Read the article

• Do I need liquid cooling?

  - by Mrrvomun

  I'm building a computer mainly for gaming and developing games. It's going to be a three screen system with two GeForce GTX 460's and a quad-core i7. The newegg wattage calculator says I need around 900W. The case I intend to get is this one. Full specs if you need 'em are at the end of this post. I have no intentions to overclock the system at the moment, but this may change in the future. I've done a lot of research on the subject, and the answers I've found indicate that it takes a heck of a lot of power to require liquid cooling, and most non-overclocked systems don't need it. But I haven't seen a question about a system with two GPU's, so I ask you the following two questions: Assuming that the system is used for gaming for very extended periods of time (say 4-6 hours at a time, nonstop) with all three screens running at full 1080p, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? If the system is used under the same circumstances as above, and is overclocked to a reasonable level, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? Specs: Intel Core i7 16GB DDR3 Two nVIDIA GeForce GTX 460 3TB HDD Two DVD-RW writers Thermaltake 1050W power supply Case is linked above

  Read the article

• How do you get Windows 7 to show time remaining in the battery meter?

  - by MrDaniel

  Running Microsoft Windows 7 Home Premium on a HP Laptop. The system tray power meter never shows the time remaining in the system tray. Only really ever show a percentage remaining number as pictured. The windows help documentation on the "battery meter" seems to indicate that it should display a time remaining indicator, is this accurate? How accurate is the battery meter? The accuracy of what the battery meter reports—what percentage of a full charge remains and how long you can use your laptop before you must plug it in—depends on several factors. Most of these factors fall into the following two categories: What you use the laptop for. Because some activities drain the battery faster than others (for example, watching a DVD consumes more power than reading and writing e-mail), alternating between activities that have significantly different power requirements changes the rate at which your laptop uses battery power. This can vary the estimate of how much battery charge remains. Battery hardware and sensor circuitry. Newer, "smart" batteries are equipped with circuitry that calculates the measurements of charge remaining and reports the information to the battery meter. Older batteries use less sophisticated circuitry and might be less accurate.

  Read the article

• Windows 7 disk backup and clone for deployment to multiple systems

  - by gregmac

  I'm in the process of deploying some new PCs (there's only 8), all identical hardware. What I'd like to do is install Windows 7 (64bit), join to domain etc, install a bunch of other software, and then clone that drive to multiple other machines. I'd also like to be able to use it as a backup image, so the machine can be restored back to that image at some future date. I understand this involves at least sysprep, but I am confused after reading some tutorials that talk about using Windows Automated Installation Kit, or hacks with the registry and custom-build batch files. This process seems overly complex to me: I did something similar 10+ years ago, and and don't remember it being this bad. Surely things have improved in a decade? There's also some products that involve having network servers running deployment software, network boot, etc etc.. this is way more than I want to set up. My systems are all identical hardware. Is there a simplified way to clone PCs? Preferably (since I'm a lazy developer, and not an IT admin) I'd like to find some off-the-shelf product that I can run after I get the machine setup, that will spit out a bootable DVD I can run on all the other systems, which will boot up, ask for a computer name, join it to the domain, and that's it. Does such as product exist?

  Read the article

• Toshiba Qosmio: Battery Stuck at 60%, does not Charges, PC can't power up, can't remain on with out

  - by Fellknight

  Just like the tittle says, now let me try to give some more detail about the symptoms; The battery is stuck at 60 percent (68% at the moment of this writing).When hovering over the battery icon in Windows 7 Home Premium x64 it reads:"68% available (plugged in, charging)", there's no x or any sing the OS is displaying any error. No matter how much time left connected to the AC adapter the battery doesn't charge, it seems however it continues to discharge at its normal rate when disconnected from the laptop (about 1% each 2 weeks). Now this last symptom is the one i find most strange it "seems" the laptop somehow isn't recognizing the battery because even with the remaining charge of 60%(ish) the laptop wont power up or remain on if disconnected from its AC adapter(if it's on and is unplugged it will immediately turn off). Meaning that even with the battery attached correctly in its right place is as if running the laptop with no battery at all. Toshiba's Utilities haven't detected anything strange (or anything for that matter) with the battery or the hardware. The laptop when in use is connected 90% of the time to a Belkin surge protector (like my 1TB EHD). The protector is working correctly (green light on) and the 1TB HD too, thus a power surge having damaged it's very unlikely. Thnx in advance

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• File transfer from MP3 player to computer

  - by JP

  I own an old 20GB Creative Zen jukebox (all external screws are gone on it LOL) and I would like to transfer files back to my PC to get them on my new iPod. Problem is, no matter what software I use (WinAMP, Creative Media Source or Windows Media Player), it just stops transferring files on my HD with an error message that says there is no more space on the destination folder. Problem is, there is still 320GB free. I tried lot of things like installing newer driver, latest Zen plug-in for Media Source, latest WinAMP version. Sometimes, it just works and then again, it stops working and I get this non-sense error. Restarting my PC sometime solves the issue by giving me enough time to transfer 10 or 15 more files and then I get the error again and again. Yesterday though I managed to transfer up to 3GB of MP3s on my computer before getting the error. Seems like I'm having a driver issue or a weird behavior from the player and/or the software I'm using. 3 different software can't reproduce the exact same issue by themselves so it must be something related to the driver. I can't find any post of any sort concerning such issue on old forums. Any idea?

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Exporting Client Data from Groupwise 6.5 to Outlook 2010 without Crashing

  - by Adam Doherty

  My employer has recently moved from Novell GroupWise 6.5 to Exchange 2010. We've imposed mailbox limits on staff but we still need to move their old messages, contacts, calendars, etc. over to Outlook 2010. Our problem however is this, utilizing the Novell MAPI client is slow within Outlook 2010 and upon exporting messages to a PST file (for later re-attachment, and offline backup purposes) crashes the GroupWise server. Connecting to the server in Outlook via IMAP to export messages to PST is faster and apparently more stable but also crashes the server. We'll be keeping our GroupWise server online internally until then end of the year but I have staff with mailboxes approaching 12 gigabytes, which is fine if we're going to move the data to offline storage (DVD set) but if I keep crashing the server every time I try to get the data I'll just be spinning my wheels. In my first attempts, I tried to move mail for a staff member with 3GB of data. The transfer lasted roughly 8 hours before crashing. I'm wondering if there is an open source solution to my problem. Paid solutions exist but we're a not-for-profit organization and have too many staff to justify the costs of per seat licenses just to migrate mail.

  Read the article

• Choosing the right TV tuner - USB or PCI TV tuners, hardware/software, DVB? Hybrid/combo/analog?

  - by Nucleon

  Greetings, I'll start with some background information so you know what I'm trying to accomplish and then get to my question. I work at a Television station in the US and we are working on setting up an online DVR/Podcast system for all of our newscasts. So basically we would be recording every newscast in HD, encoding it to flv/h.264 for viewing in a browser on flash compatible and iphone/ipad devices, eventually migrating to WebM when it's browser compliant. This task is theoretically pretty simple as it all it involves is a TV tuner device and a program like VLC, MythTV or whatever to schedule and dump it to a file, encode it with VLC/FFMPEG and push it to the streaming server. Now to the hardware, in order to accomplish that task, should I use an internal PCI tuner or a USB 2.0 tuner? Is there a difference? The bus speeds of both are not too far apart, and is the bus speed really relevant in this case? Does it matter if the device has a hardware encoder or a software encoder? On many sites the USB was recommended for ease of set up and use, but would it overly task a processor, or is that not a concern as long as it's a decent PC (at least duo core, 6gb ram). What's the difference between the stick USB and the Box USBs? To my understanding analog is basically gone in the US, so we would want a hybrid or combo tuner correct? How do those differ from DVB? Are there any other features or concepts which I am missing which may influence the recommended product. It would be ideal if the device which could work in both Linux and a Windows environment, to my knowledge most Hauppauge are? Example 1: PCI Hauppage http://www.newegg.com/Product/Product.aspx?Item=N82E16815116033 Example 2: USB 2.0 Box http://www.newegg.com/Product/Product.aspx?Item=N82E16815116029 Example 3: USB 2.0 Stick http://www.newegg.com/Product/Product.aspx?Item=N82E16815116031 Any guidance from the Superusers would be much appreciated!

  Read the article

• Is my HDD dead forever?

  - by Roberto

  Yesterday I turned on my computer and it couldn't boot. I found out the hd (320GB SATA Seagate Momentus 7200.3 for notebook) was broken and it couldn't be recognized by the BIOS. I have another of the same hard drive, so I exchanged the boards. I found out that there is a problem on its board since my good hard drive didn't work. But the broken hard drive doesn't work with the good board as well: it can be recognized but when I insert a Windows Instalation DVD it says the hard drive is 0GB. I put it in a case and use it in another computer via USB, and but it doesn't show up in the "My Computer". I used a software to recover files called "GetDataBack for NTFS", it recognized the hard drive but with the wrong size (2TB). I try to make it read the hard drive but it got an I/O error reading sector. It tries to read, the hard drive spins up. So, since I'm using a good board on it, the problem seems to be internal. Is there anything someone could do to recover the files from it?

  Read the article

• How to speed up a HP M9517C

  - by Jen

  I bought a system with 8GB RAM, 1TB HD, Quad-Core AMD Phenom 9550, Nvidia Geforce 9300GE, 64-bit Windows Vista Machine. Bought it primarily because it was cheap and came with 25.5 inch screen. Problem: It's slow - if you can believe it. My Dell laptop 1525 is faster and more stable! I tried installing and dual-booting Linux Mint and ran into video and audio troubles. I need fast and stable and I'm going for awesome. Anyone have some suggestions on making this thing smoking hot? Vista is fine, but slows over time - suspect virus/spyware/etc.. But I need to use Photoshop, Fireworks, Dreamweaver, Illustrator. I've tried the alternatives and I just don't like them. When you've got deadlines looming you want to work with what you know. Also use Skype (and I had audio problems with it in Linux), gotomeeting, gotowebinar. Don't need MS Office. Tried VMWare, Virtualbox and again - I keep getting audio/video problems. I'd love someone's input on THEIR setup and how they got there. I'm sure I need to upgrade my video card, but what should I go to?

  Read the article

• Cannot login to Windows7 in normal mode but can in safe mode

  - by Guy

  I have a Windows 7 Ultimate computer (Shuttle) that I built myself and in it I put a Solid State Drive (SSD). It's been working well for a number of months but now when I start it there are problems. I have 2 users setup on the computer and when I try and sign in with either user it claims that the password is incorrect. I could understand the odd typo but I've had my wife try it as well and we've got the passwords correct. On top of that it will remain at the login screen for 1 minute and 20 seconds and then spontaneously reboot without shutting down. So I'm trying to work out if this is a hard disk problem or something else. Any ideas? (I have a nightly backup to a WHS so it will be easy to recover but I don't want to do that unless I have to and don't want to waste time putting in a new HD just to discover it's something else.) More info: If I start in Safe Mode I am able to login with the password and all appears as normal as it can in Safe Mode. However, normal boot continues with same problem.

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Hi, Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• I must clear my cmos to be able to boot

  - by Fredou

  I have this Asus p7p55d-e pro for about 8 months(got it last July) and for this last 3-4 days I cannot boot without clearing my CMOS what I have is: Seasonic M12D 750W ASUS P7P55D-E Pro Intel Core i5 760 Quad Core Processor Lynnfield LGA1156 XFX GeForce® 8800 GT Alpha Dog 512MB DDR3 Standard (PV-T88P-YDF4) 2x Corsair XMS3 CMX4GX3M2A1600C7 4GB DDR3 2X2GB DDR3-1600 CL 7-8-7-20 I tried to remove all the unnecessary stuff: HD/dvd/pci card/usb cable/etc I tried with only 1 dimm filled, instead of my 4, each one individually it didn't work I tried changing the battery, here goes a few dollars to nowhere, didn't work if I don't reset the CMOS it sometime stock on RAM led, sometime on BOOT DEVICE led, when this happen, it stuck on CPU speed detection when I boot right after the reset, i MUST click on the F2 option (boot with default bios setting) if i go into the bios and save/restart, i have to reset it again when booted, everything is rock solid stable, tried memtest, cpu stress, etc, etc. without issue what should be my next step? trying a new psu? (i need to find one..) doing rma? (i need this mb since it's my only computer...) something else?

  Read the article

• What can I do to lower bandwidth cost on a bandwidth heavy site?

  - by acidzombie24

  The easiest answer is CDN but I'd like to ask. A friend of mine has a server that is used for mirror downloads. He says he is doing about 10TB of bandwidth a month which shocked me (I wonder if he is lying). I seen his site and he has no ads. I suspect he might close his website once he gets the bill. Anyways I was wondering since his CPU/RAM is not being used and his HD usage is around 15gb what he can do to lower cost if he continues this site. I said put up ads but I don't know if ads would cover it I found one CDN which offers $0.070 / GB. 10240gb (10TB) * .07 = $717 a month. That seems a little steep but he is using lots of traffic due to it being a mirror site. Also using a CDN doesnt make sense as he doesn't need multiple servers hosting the files in different areas (which is one reason he isn't using that now). He just needs a big upload pipe Is there something he can do? At the moment he is paying $200 a month on a dedicated server and he is using WAY more bandwidth then he should be using. Side question: Can gz-ing files large already compressed files help? like on (zip, rars, etc)

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• keyboard intermittently stops working even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash the ctrl+alt+windows keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) Unplugging & reconnecting keyboard does NOT fix it. Connecting a different keyboard does NOT fix it. That one won't work, either. Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears the keyboard won't work and neither will the icon to pull up the on-screen keyboard. My mouse can click around just fine. I can only log onto a non-password protected account. Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. Clearing my Chrome browsing data stopped the problem from recurring for a week or so. I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. I use Avira free antivirus software, and repeated scans turn up nothing fishy. I suspect it is related to something in Google Chrome because I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• Can't Get Mac Mini to turn on - no screen, no beep, only the fan, power light, and optical drive noi

  - by pibyers

  I have an Intel-based Mac mini mid-2007 (Model A1176). This is the computer my kids use so I don't use it regularly. The computer had been working fine until one day my kids told me that it no longer works. The computer will not boot up. When I turn it on the fan turns, the white power light in the front turns on, and there is a sound that appears to be from the optical drive (rather than hard drive). I don't get anything to the monitor, nor do I get any dings or other start up sounds from the computer. Here is what I've tried thus far to no avail: 1) Swapped out the monitors early on since I figured that was my weak link - no change 2) Reset the PMU - no change 3) Tried to boot up from the System Disk - The mini loaded the dvd into the drive, but nothing else (I can't eject the disk so I can put it back) 3) Start up the computer in target mode connected to another mac - I tried this too, but I never received a chime or the disk show up on the other mac. I'm about out of ideas apart from scraping the computer. Does anyone have any ideas that I can try? Again, nothing has been done to the computer in at least 6 months when I upgraded the RAM. I'm also still on Leopard. Thanks.

  Read the article

• "cannot receive new filesystem stream: invalid backup stream" error when unpacking flash archive on solaris 10

  - by Bovril

  I've searched around but i'm having no luck with some peculiar behavior with a flash archive. I'm using HP Server Automation 9.14 to deploy the OS. I'm creating a Solaris 10 flash archive to create a snapshot default build in our environment. I create the flash archive with # flar create -c -S -n g8-solaris10-u10 g8-solaris10-u10.flar It seems to create the file without any problems (exit status 0). When deploying to a new system (same hardware), it extracts to a point and then bails. The last error in the log I can see is Extracted 2047.00 MB ( 82% of 2488.98 MB archive) ERROR: Could not read file (172.27.118.100:/media/opsware/sunos/flar/g8-solaris10-u10.flar ERROR: Errors occurred during the extraction of flash archive. The file /tmp/flash_errors contains the list of errors encountered ERROR: Could not extract Flash archive ERROR: Flash installation failed The error log contained the following message cannot receive new filesystem stream: invalid backup stream A previous version of this flash archive (1.8gb) worked ok, so I suspect size may be a factor. The source system (the one the flash archive is an image of) is an HP BL460C GEN8 some more info below. OS version Info # uname -a SunOS testhostname 5.10 Generic_147441-01 i86pc i386 i86pc # who -r . run-level 3 Oct 15 08:15 3 0 S disks # echo | format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0t0d0 <DEFAULT cyl 17841 alt 2 hd 255 sec 63> /pci@0,0/pci8086,3c06@2,2/pci103c,3355@0/sd@0,0 Specify disk (enter its number): Specify disk (enter its number): zpools # zpool list NAME SIZE ALLOC FREE CAP HEALTH ALTROOT rpool 136G 24.6G 111G 18% ONLINE - Zones # zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / native shared The file size of 2047 seems suspiciously close to 2048, which is concerning. Any help would be greatly appreciated. Thanks

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• Confused about the Windows 7 Preinstallation Kit

  - by David Brown

  I build custom PCs and would like to use the Windows 7 Preinstallation Kit to make installation go a little quicker and customize the Windows image. However, since each PC is built to a particular customer's specifications, the hardware will rarely be the same. So, I would like to have a single answer file that will work for everything. I'm not sure if that's possible, however. What I mostly want to do for now is add my support information as well as pre-set anything that I would normally change after each installation completes. I have a Windows 7 Professional Upgrade DVD set (both 32-bit and 64-bit), but no OEM disks. I copied the Install.wim file to my local drive and opened it in the Windows System Image Manager, but it asks me to choose a catalog file specifically for each edition of Windows 7. Will this limit the answer file to whichever edition I choose? I would think choosing Starter would give me the most basic settings, which would apply to all other editions, but I'm not entirely sure of this. I don't intend to install any extra applications or drivers. I merely want to insert an OEM disk, my OPK USB drive, and have it work for whatever edition of Windows 7 I'm installing. If a large number of similarly-configured PCs need to be built, I'll go ahead and create a custom answer file in that case, but for a single machine order, that seems like overkill. In addition, do I need a separate answer file for 32-bit and 64-bit versions of Windows 7? Or will it work for both, even though I copied the Install.wim file from the 32-bit disk? Thanks!

  Read the article

• Why does the file date always change to the current date?

  - by Marshall

  We are a programming shop, but this i snot a programming question. My boss has put an external HD on the network. It contains the 'home' folders for users on the network. He uses it to place VB projects that he wants me to work on. But no matter what date and time he places a project on the drive, the file dates(modified) always shows the current date, though nothing in the files have changed. It makes it very hard to confirm that he has given me the latest versions. (He is not a fan of version control and nothing I do will convince him different.) Any ideas why this happens and how to prevent it from happening? P.S. As I wrote this I decided to add the last accessed date to the file display, and those dates happen to show the dates I expect to see. Why is the modified date getting changed, but not the accessed date. Does the accessed date change only when the files are opened or read, changed or not? Note: I use Directory Opus 9, a replacement for windows file browser. Thanks, Marshall

  Read the article

• What configuration changes can I make to speed up extremely slow Windows VM's in ESXi 4.0.

  - by Shawn Anderson

  I've recently moved from VMWare Server to ESXi 4.0. Running on Dell T310. My VM's have been restored but they are running dog slow compared to VMWare Server. I loaded ESXi 4.0 using only default values. Where are some areas where I can tweak the performance? Even logging onto the VM's can be extremely sluggish. Trying to install software on any of them is a new experience in pain. Dell PowerEdge T310 Xeon X3460 2.80 GHz 32 GB RAM 1 HD (2 TB) I have 16 VM's on this server, but only six or so will be running during my testing. I keep an eye on the Resource Allocation and Performance tabs for the host and I never see CPU or RAM getting anywhere close to pegged. Events tab does show some notices for video RAM issues and some hints on Windows activation issues, but nothing that would point to the sort of sluggishness that I'm experiencing. 1 Windows Server 2008 R2 (64-bit) - 4 GB RAM 1 Windows 7 (32-bit) - 2 GB RAM 1 Vista (32-bit) - 1 GB RAM 3 XP (32-bit) - 1 GB RAM Over to you! Thanks - Shawn

  Read the article

• Installing Linux on an Asus p8z68-m PRO Motherboard

  - by Holland

  Here is a challenge: how is this done? I've tried disabling the ASM1061 controller in the Onboard Devices section, using Wubi, booting from USB (as I don't have a DVD drive, yet), and even booting from RAID/IDE (with AHCI as the default) to do this. Still, no dice. Google shows up virtually nothing related about Linux and this mobo, apart from a people just saying "disable ASMedia" (which, I assume is the ASM1061 controller, as that's all I see - apart from the USB 3.0, which I disabled already) and it hasn't really helped much. Thus, what is wrong here? Edit My problem is that I cannot boot Linux via USB or a simple Windows installer such as Wubi (for Ubuntu). I wind up getting error messages along the lines of write cache failed, along with many other cryptic error messages similar to the following: [ 1400.351374] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled [ 1400.353433] sd 4:0:0:0: [sdb] Asking for cache data failed [ 1400.356601] sd 4:0:0:0: [sdb] Assuming drive cache: write through This seems to be common for Asus P8Z68-M Pro motherboards, with the only notable solution being to "disable ASMedia", which, as I said before, I'm guessing is the ASM1061 controller on the motherboard. Despite already disabling this, I have tried this with both Fedora and Ubuntu without any success. I need to know what I can do about this; has anyone ran into something similar or heard about this issue before? I know these motherboards are relatively new...

  Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >