Search Results

Search found 9125 results on 365 pages for 'boot disc'.

Page 137/365 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

  • Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

    - by Pro Backup
    In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

    Read the article

  • How to restore windows.old for windows 7

    - by Jim Thio
    I reinstall windows. Then I regret that and want to go back. Fortunately the old windows is stored at windows.old I follow the instruction in http://support.microsoft.com/kb/971760 I did it all with small catches When I insert the windows 7 installer, the drive for installer is X and my hard disk is D rather than C. However, on normal windows operation the drive is C. Only when I boot through CD the partition is assigned to the letter D. There is no file bootsect on my windows installer So I can't do **D:\boot\bootsect /nt60 c:** Which should be changed to X:\boot\bootsect /nt60 C: or X:\boot\bootsect /nt60 D: depending on what it really does. As I said if I boot through windows dvd my hard disk letter is D but normally it's C. I am not even sure what that bootsect does anyway. I also can't do this one Attrib –h –s –r boot.ini.saved Copy boot.ini.saved boot.ini There is no file boot.ini or boot.ini.saved It's hidden but I don't see it if I try to look unhidden files either. Because I simply switch from windows 7 to windows 7 and the directory for windows don't change c:\windows I thought it should still work. Well, it doesn't. When windows restart it only goes to the logo and then restart the computer.

    Read the article

  • Trouble burning CDs and DVDs in Windows

    - by Cory
    I've run into some errors writing CDs and DVDs recently: Trying to burn a dual layer disc using ImgBurn I come across this error when trying to finalize the disc. Potential 'WaitImmediateIO' Deferred Error - (0%, 0/3) - Session Fixation Error Writing Lead In Finalise Disc Failed! - Reason: Session Fixation Error Writing Lead In Anyone have an idea what could be the problem? There is no problem until it comes time to finalize the disc

    Read the article

  • Dead laptop screen rewired to external only right from boot-up?

    - by Wesley
    I have a Compaq CQ50-215CA laptop and after a year and 5 months, the screen is completely distorted now. I plan on removing the screen soon, but I realize that the BIOS screen, OS select and Vista boot sequence are all displayed on the laptop screen rather than the external display. Is there some way to get the laptop to display everything (From boot-up to shutdown) on an external display (VGA port)?

    Read the article

  • Ubuntu 12.04: Does grub support multidevice boot from btrfs?

    - by Propantriol
    I'm using Ubuntu 12.04 LTS (Precise Pangolin) with grub 1.99. I installed on a RAID10 multidevice BTRFS partition. I thought that multidevice support is included in grub for a while but on boot I'm dropped to a initramfs shell, because it fails to mount root ("invalid argument"). This is actually the same message I get if I want to mount a btrfs volume without executing btrfs device scan. Therefore I wonder: Does Ubuntu's grub version even support boot from btrfs mutlidevice ?

    Read the article

  • No grub selection after installing kernel Ubuntu 14.04

    - by CPJ
    I have installed a new kernel on my system which can be found by grub but when I restart I can only select the old kernel. Things I tried in other threds with similar problems didn't help. sudo update-grub gives Generating grub configuration file ... Found linux image: /boot/vmlinuz-3.15.0-031500rc2-lowlatency Found initrd image: /boot/initrd.img-3.15.0-031500rc2-lowlatency Found linux image: /boot/vmlinuz-3.15.0-031500rc2-generic Found initrd image: /boot/initrd.img-3.15.0-031500rc2-generic Found linux image: /boot/vmlinuz-3.13.0-24-generic Found initrd image: /boot/initrd.img-3.13.0-24-generic Found memtest86+ image: /boot/memtest86+.elf Found memtest86+ image: /boot/memtest86+.bin done However, afer a reboot I can only choose the 3.13 kernel. Any ideas what happened? I I have a full encrypted hard drive so maybe I have overseen something while installing the new kernel to get this work? The grub config file is GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT_QUIET=false GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="" GRUB_ENABLE_CRYPTODISK=1 Any ideas? Thanks.

    Read the article

  • How do I get my mac to boot from an Ubuntu USB key?

    - by Vinay Gupta
    so if you select "mac" and "usb" on this download page, it gives a series of command line instructions to make a USB key which the MacBook will boot into Ubuntu from. http://www.ubuntu.com/desktop/get-ubuntu/download I've followed them to the letter two or three times on different USB keys, and it doesn't work. There's a very great deal of technical discussion about EFI etc. but this set of instructions seems to suggest it should Just Work, and it doesn't. Help? I'm increasingly unhappy with the more locked-down approach Apple is taking, and I'd quite like to start using Linux with a view to transitioning over to using it as my main operating system, but booting from the CD takes forever, runs slowly and I'm really hoping to get it moving off USB. Can anybody help me?

    Read the article

  • Which tools helps to start Ubuntu GUI when boot?

    - by Vimal Kumar
    I am on the way to create a Live CD from scratch. I used Virtual Box for this purpose. I installed Ubuntu base from ubuntumini.iso and installed gnome-shell. And installed Remastersys and created a backup.iso. Burned in a CD and boot from a PC. It end in CLI. Not lead to GUI. I tried the same ISO in VirtualBox. But it work properly there. I think I missed some packages which help to start GUI. Can you help me to identify the packages missed to include in the CD?

    Read the article

  • Deleted entire harddisk. Now my laptop won't boot anything and stuck at grub rescue!

    - by Jahan
    My laptop is Dell Inspiron N4030. I used to use Ubuntu 12.04 and it was on the entire hard drive. I tried to install windows 7 but my laptop couldn't install it. So, I decided to delete the entire hard drive and do a fresh install of Windows 7. But after deletion I immediately removed the gparted live usb which I was using to delete the partitions of my hard drive. And then tried booting from windows 7 cd, didn't work, tried ubuntu live cd, didn't work, tried hiren's boot cd, didn't work, tried super grub disk, didn't work. Probably I'm not doing it right. Help needed badly.

    Read the article

  • System freeze after opening Wi-Fi menu can boot into the machine and use Internet in recovery mode

    - by Michael
    So right now sitting in front of my Alienware area 51 desktop. It has a Broadcom Netlink BCM 5784M gigabit ethernet PCI E card. Most of the time able to get through the login screen and to the main screen if I click on the wireless settings on the top right-hand corner the system immediately freezes the cursor does not move at all keyboards are unresponsive. I was doing some quick Google searching and I found a suggestion to boot into recovery mode I did this and did a apt-get Distribution update which ran successfully installed then I rebooted into the regular system same thing I'm pretty sure it's the network card because even if I don't click the settings if a network related dialog opens such as disconnection or connection the system again immediately freezes. I'm running Ubuntu 13.04 ** update 1 ** Just was able to use my system for a little bit however when I went into Firefox and hit the web it again froze so obviously a driver problem but I'm not sure how to get drivers for Broadcom which apparently according to the description on stack-overflow is terrible Any ideas? Sorry for lack of punctuation on an ipad.

    Read the article

  • 'unknown filesystem' grub rescue prompt; trying to wipe drive and boot 10.10 live

    - by Patrick
    Im currently running Win7, and want to wipe the drive and install 10.10. I have 10.10 loaded on a USB thumbdrive and it sees the device in BIOS but it only reaches a screen saying; Unknown Filesystem grub rescue> Ive read several results from google and a couple here where people are trying to dual boot and i assume save the data on the drive, but i dont care about doing that, and would prefer to just wipe the drive and start fresh. What steps can i take to get the drive to a point where i can load 10.10 live and get it installed?

    Read the article

  • Half the time Linux drop into BusyBox; the rest of the time the boot happens normally

    - by JoBu1324
    I just installed Ubuntu x64 onto a USB3 Drive from a DVD, and half the time it appears to skip the grub menu and boots directly into BusyBox. Since the USB3 drive is an SSD, I ran through the full installation (installing on an ext4 partition, along side a 1GB boot partition at the start of the disk), skipping the swap partition. Part of the time that the Grub Menu does shows, it boots into BusyBox with an error: ALERT! /dev/disk/by-uuid/[uid] does not exist. Dropping to a shell! What could cause such an issue?

    Read the article

  • How to automatically mount a Windows shared folder on every boot up?

    - by Zabba
    I am able to access Windows' shared folder from Ubuntu 10.10 Nautilus like so: Type into the Location Bar : smb://box/projects Now, I can see the folder in Nautilus, create/read files in it. Also, on desktop I get a folder called "projects on box". But, that folder on the desktop goes away when I reboot. So, I thought that I can automount the Windows' shared projects folder by adding this to my fstab: //box/Projects /home/base/Projects smbfs rw,user,username=jack,password=www222,fmask=666,dmask=777 0 0 (base is my user name on Ubuntu) Now, I get a folder called "Projects" in my home folder after boot up, but it is empty (cannot see the same files that I can see in Nautilus). What's am I doing wrong? Some more detail: This is what I see of the Projects folder when I do ls -l in my home folder: ... drwxr-xr-x 2 root root 4096 2011-01-01 10:22 Projects drwxr-xr-x 2 base base 4096 2011-01-01 09:06 Public ... Note the two "roots". Is that somehow the problem?

    Read the article

  • How do I remove Ubuntu from a dual-boot Windows 7 laptop?

    - by Alex
    Im new to Ubuntu and liked it a lot! however after testing it on my old crappy laptop i now want to remove it. Ive looked at tutorials on how to uninstall and it says to start by deleting the linux partition of the hard drive.however after opening Computer management, I cannot locate my linux partition. same as when I go to System Configuration, and click on the "boot" tab, my computer does not list any operating system other than Windows 7. Any Way around this or perhaps a different way to uninstall?

    Read the article

  • Why does my screen blank out for the duration of the Grub boot menu?

    - by hushs
    Upon booting, when I should see the GRUB menu, my monitor simply says: "No optimum mode. Recommended mode: 1600*1200". If I wait for a short while, Ubuntu starts to boot and it reaches the desktop. So I guess there is no video signal during that time, there's the grub menu but I cant see it and after the wait time everything is fine. I have the same problem when I log out for a short moment, before the log in screen is reached. and this also happens when i shut down ubuntu. The VGA is an onboard NVIDIA GeForce 7025.

    Read the article

  • How do I get my Mac to boot from an Ubuntu USB key?

    - by user11621
    If you select "USB" and "Mac" on this download page, it gives a series of command line instructions to make a USB key which the MacBook will boot into Ubuntu from. I've followed them to the letter two or three times on different USB keys, and it doesn't work. There's a very great deal of technical discussion about EFI etc. but this set of instructions seems to suggest it should just work, but it doesn't. Help? I'm increasingly unhappy with the more locked-down approach Apple is taking, and I'd quite like to start using Linux with a view to transitioning over to using it as my main operating system, but booting from the CD takes forever, runs slowly and I'm really hoping to get it moving off USB. Can anybody help me?

    Read the article

  • Install Ubuntu Netbook Edition with Wubi Installer

    - by Matthew Guay
    Ubuntu is one of the most popular versions of Linux, and their Netbook Remix edition is especially attractive for netbook owners.  Here we’ll look at how you can easily try out Ubuntu on your netbook without a CD/DVD drive. Netbooks, along with the growing number of thin, full powered laptops, lack a CD/DVD drive.  Installing software isn’t much of a problem since most programs, whether free or for-pay, are available for download.  Operating systems, however, are usually installed from a disk.  You can easily install Windows 7 from a flash drive with our tutorial, but installing Ubuntu from a USB flash drive is more complicated.  However, using Wubi, a Windows installer for Ubuntu, you can easily install it directly on your netbook and even uninstall it with only a few clicks. Getting Started Download and run the Wubi installer for Ubuntu (link below).  In the installer, select the drive you where you wish to install Ubuntu, the size of the installation (this is the amount dedicated to Ubuntu; under 20Gb should be fine), language, username, and desired password.  Also, from the Desktop environment menu, select Ubuntu Netbook to install the netbook edition.  Click Install when your settings are correct. Wubi will automatically download the selected version of Ubuntu and install it on your computer. Windows Firewall may ask if you want to unblock Wubi; select your network and click Allow access. The download will take around an hour on broadband, depending on your internet connection speed.  Once the download is completed, it will automatically install to your computer.  If you’d prefer to have everything downloaded before you start the install, download the ISO of Ubuntu Netbook edition (link below) and save it in the same folder as Wubi. Then, when you run Wubi, select the netbook edition as before and click Install.  Wubi will verify that your download is valid, and will then proceed to install from the downloaded ISO.  This install will only take about 10 minutes. Once the install is finished you will be asked to reboot your computer.  Save anything else you’re working on, and then reboot to finish setting up Ubuntu on your netbook. When your computer reboots, select Ubuntu at the boot screen.  Wubi leaves the default OS as Windows 7, so if you don’t select anything it will boot into Windows 7 after a few seconds. Ubuntu will automatically finish the install when you boot into it the first time.  This took about 12 minutes in our test. When the setup is finished, your netbook will reboot one more time.  Remember again to select Ubuntu at the boot screen.  You’ll then see a second boot screen; press your Enter key to select the default.   Ubuntu only took less than a minute to boot in our test.  When you see the login screen, select your name and enter your password you setup in Wubi.  Now you’re ready to start exploring Ubuntu Netbook Remix. Using Ubuntu Netbook Remix Ubuntu Netbook Remix offers a simple, full-screen interface to take the best advantage of netbooks’ small screens.  Pre-installed applications are displayed in the application launcher, and are organized by category.  Click once to open an application. The first screen on the application launcher shows your favorite programs.  If you’d like to add another application to the favorites pane, click the plus sign beside its icon. Your files from Windows are still accessible from Ubuntu Netbook Remix.  From the home screen, select Files & Folders on the left menu, and then click the icon that says something like 100GB Filesystem under the Volumes section. Now you’ll be able to see all of your files from Windows.  Your user files such as documents, music, and pictures should be located in Documents and Settings in a folder with your user name. You can also easily install a variety of free applications via the Software Installer. Connecting to the internet is also easy, as Ubuntu Netbook Remix automatically recognized the WiFi adaptor on our test netbook, a Samsung N150.  To connect to a wireless network, click the wireless icon on the top right of the screen and select the network’s name from the list. And, if you’d like to customize your screen, right-click on the application launcher and select Change desktop background. Choose a background picture you’d like. Now you’ll see it through your application launcher.  Nice! Most applications are opened full-screen.  You can close them by clicking the x on the right of the program’s name. You can also switch to other applications from their icons on the top left.  Open the home screen by clicking the Ubuntu logo in the far left. Changing Boot Options By default, Wubi will leave Windows as the default operating system, and will give you 10 seconds at boot to choose to boot into Ubuntu.  To change this, boot into Windows and enter Advanced system settings in your start menu search. In this dialog, click Settings under Startup and Recovery. From this dialog, you can select the default operating system and the time to display list of operating systems.  You can enter a lower number to make the boot screen appear for less time. And if you’d rather make Ubuntu the default operating system, select it from the drop-down list.   Uninstalling Ubuntu Netbook Remix If you decide you don’t want to keep Ubuntu Netbook Remix on your computer, you can uninstall it just like you uninstall any normal application.  Boot your computer into Windows, open Control Panel, click Uninstall a Program, and enter ubuntu in the search box.  Select it, and click Uninstall. Click Uninstall at the prompt.  Ubuntu uninstalls very quickly, and removes the entry from the bootloader as well, so your computer is just like it was before you installed it.   Conclusion Ubuntu Netbook Remix offers an attractive Linux interface for netbooks.  We enjoyed trying it out, and found it much more user-friendly than most Linux distros.  And with the Wubi installer, you can install it risk-free and try it out on your netbook.  Or, if you’d like to try out another alternate netbook operating system, check out our article on Jolicloud, another new OS for netbooks. Links Download Wubi Installer for Windows Download Ubuntu Netbook Edition Similar Articles Productive Geek Tips Easily Install Ubuntu Linux with Windows Using the Wubi InstallerInstall VMware Tools on Ubuntu Edgy EftHow to install Spotify in Ubuntu 9.10 using WineInstalling PHP5 and Apache on UbuntuInstalling PHP4 and Apache on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Explorer++ is a Worthy Windows Explorer Alternative Error Goblin Explains Windows Error Codes Twelve must-have Google Chrome plugins Cool Looking Skins for Windows Media Player 12 Move the Mouse Pointer With Your Face Movement Using eViacam Boot Windows Faster With Boot Performance Diagnostics

    Read the article

  • Ubuntu boot hangs after message "Running /scripts/init-bottom ... done"

    - by Douglas B. Staple
    I've been trying to copy a Proxmox container based on the Ubuntu Precise Standard template to a VirtualBox VM. I am now stuck at a point where my new Ubuntu/VirtualBox VM hangs after the message "Running /scripts/init-bottom ... done" during boot. I started by installing Ubuntu Server 12.04.4 LTS on a VirtualBox VM. Ubuntu Server 12.04.4 LTS was the closest "official" Ubuntu ISO to the Proxmox container OS I could find. I installed all updates on both the Proxmox container and on the VirtualBox VM. The idea was to get same version kernal running on the ProxMox container and VirtualBox VM. sudo apt-get update ; sudo apt-get upgrade ; sudo apt-get dist-upgrade sudo reboot rsync the entire proxmox container to a temporary directory in the VirtualBox VM: cd / mkdir /tmp/backup rsync -e ssh -av --exclude={/dev,/proc,/sys,/tmp,/run,/mnt,/media,/lost+found,/boot,/selinux} root@my_proxmox_container_hostname:/ /tmp/backup Shut down the virtual machine, and boot the VM with a bootable linux image. I used the Desktop image of Ubuntu 12.04 LTS, ubuntu-12.04.4-desktop-i386.iso Drop to a root prompt. Mount the VM root filesystem: sudo mount /dev/sda1 /mnt Remove files from most of /mnt cd /mnt sudo rm -rf bin etc home lib opt sbin root usr var Move all of the files from /mnt/backup into /mnt sudo mv /mnt/tmp/backup/* /mnt Rebooted system. For me, at this point the system freezes after starting, after the message: Running /scripts/init-bottom ... done I've tried reinstalling GRUB and all manner of other thing. I am almost ready to give up.

    Read the article

  • Why doesn't this for loop work?

    - by evilsoup
    This is on Ubuntu 12.04 I'm trying to figure out how to get ffmpeg to do a batch conversion of FLACs to MP3, recursively. If I cd into a directory and use for f in *.flac; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done that works perfectly fine. However, when I try this, it doesn't work: for f in "$(find . -type f -name *.flac)"; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done It doesn't even throw up any useful errors (but here is the output anyway, no need to complain): evilsoup@enchantment:~/Music/Jean Sibelius$ for f in "$(find . -type f -name *.flac)"; do ffmpeg -i "$f" -c:a libmp3lame -q:a 2 "${f/%flac/mp3}"; done ffmpeg version git-2012-12-18-b7e085a Copyright (c) 2000-2012 the FFmpeg developers built on Dec 18 2012 19:23:11 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 80.100 / 54. 80.100 libavformat 54. 49.102 / 54. 49.102 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 28.100 / 3. 28.100 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/02. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/03. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/stripped2.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/05. Symphony No.1.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/stripped3.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/09. Andante festivo.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/08. Symphony No.3.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/01. Finlandia.flac ./Symphonies 1, 2, 3 & 5 (Oslo Philharmonic Orchestra Conducted by Mariss Jansons) Disc 1/07. Symphony No.3.flac ./Symphonies 1, 2, 3 & 5 I've tested the find command on its own, and it works as expected, so the problem has to be something to do with the interaction between find and for. I'm aware that I could do something with find's -exec option, but I can't find any way to do string substitution as I can with a bash for loop, and I'd rather not have a bunch of file.flac.mp3s to deal with, even if they could be fixed with a simple rename.

    Read the article

  • How can I display additional boot and shutdown information on the Windows 7 welcome screen?

    - by Daniel Saner
    There is a small tweak, I believe it is a registry key, that allows to display additional information on the Welcome and Shutting down screens of Windows 7 (and most likely Vista, too). I have activated this tweak on one of my systems; unfortunately I forgot how I did it, and I can't seem to find the website that originally gave me that information. Usually, the Windows 7 welcome screen will just display "Welcome" when logging in. With the tweak activated, my Welcome screen gives status information such as "Loading user settings" or "Preparing desktop". When shutting down, the default screen simply says "Shutting down". With the tweak activated, it gives additional status information such as "Stopping Windows services". This appears the same way that Windows gives information when updates are installed or configured during the startup or shutdown procedure, and I find them quite helpful in getting a feel for what task takes how long during that process. The only setting I was able to find is the Boot log checkbox on the Boot tab of the msconfig application. However, this results in Windows displaying console logs of drivers it is loading, etc., instead of the animated Windows title. This is NOT the setting I am looking for. The "additional boot information" setting that I have activated on this system still displays the regular animated Windows logo, and only replaces the strings displayed on the blue Welcome and Shutdown screens. Could someone direct me to the registry key (or whatever setting) that is used to get this behaviour? Edit: Here are a few pictures of the enhanced Welcome and Shutdown screens taken with my mobile phone—they're in German though. Login screens "Waiting for User Profile Service" and "Preparing desktop": Logout screen "Stopping Windows services":

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >