Search Results

Search found 22877 results on 916 pages for 'network storage'.

Page 137/916 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

  • Customer site is out of IP addresses, they want to go from /24 to /12 netmask... Bad idea?

    - by ewwhite
    One of my client sites called to ask me to change the subnet masks of the Linux servers I manage there while they re-IP/change the netmask of their network based on a 10.0.0.x scheme. "Can you change the server netmasks from 255.255.255.0 to 255.240.0.0?" You mean, 255.255.240.0? "No, 255.240.0.0." Are you sure you need that many IP addresses? "Yeah, we never want to run out of IP addresses." A quick check against the Subnet Cheat Sheet shows: a 255.255.255.0 netmask, a /24 provides 256 hosts. It's clear to see that an organization can exhaust that number of IP addresses. a 255.240.0.0 netmask, a /12 provides 1,048,576 hosts. This is a small < 200-user site. I doubt that they'd allocate more than 400 IP addresses. I suggested something that provides fewer hosts, like a /22 or /21 (1024 and 2048 hosts, respectively), but was unable to give a specific reason against using the /12 subnet. Is there anything this customer should be concerned about? Are there any specific reasons they shouldn't use such an incredibly large mask in their environment?

    Read the article

  • Make a drive from one machine appear as a physical disk in another machine.

    - by Roberto Sebestyen
    I want to take a physical disk (or part of a disk) in one machine (call it machine-A) and I want to make it available in another machine (machine-B). But I don't want to map a network drive. I want it to appear in machine-B as a physical drive. Even though it is not a physical drive. The reason I want to do this is i want the ability to create shares in machine-B on that drive. Since I cannot do that on mapped drives, I need to use some utility that fools machine-B to think that it is a physical drive, and treat it as such. Both of these machines are windows server 2003. I heard about NFS, It sounds like what could be the solution to my problem. But isn't that a Linux/Unix protocol? What tools can I use to make this happen? Are there any open source solutions? I don't care what the solution is, as long as it achieves the end result, preferably open source solution though. Thanks for reading guys and gals!

    Read the article

  • Sync, share and backup policy using NAS

    - by Cue
    Trying to come up with a way to keep in sync while sharing and keeping a backup of my music/photos and movies. Currently I have an iMac in Greece and a MBP with me in the UK. As a result I've ended up with 2 iPhoto and iTunes libraries not to mention Documents scattered here and there, user settings etc. I also like to have a backup in case of a drive failure or the need to clean install. It seems that iPhoto and iTunes don't work really well with networked libraries. The way I think about it is to have a NAS where I keep my iTunes and iPhoto library but also rsync daily to my MBP to have a local copy. That way my files are shared across the network as well as act like a backup. In addition I get to have my files wherever I take my MBP but also have the ability to clean install. The tricky part comes from keeping in sync the iMac which is miles away. Again I'm considering a mirror setup (NAS, rsync to the iMac) as well as an rsync between the two NAS. It pretty much resembles the way Dropbox works, sans the requirement to go through their servers but I'm no "superuser" and don't really know if it is even feasible to have such a setup. Looks like there are so many things that can go wrong.

    Read the article

  • How to handle OpenVPN client as a service, when the laptop is physically on the network already?

    - by James
    The Setup I've gotten OpenVPN working on our Windows XP laptops. Users are limited, so I went ahead and set OpenVPN client to run as a service, which is great anyway because that means they are on the VPN before logging in, so login scripts work, plus we can do remote support even if the user can not log in (such as connecting via VNC or resetting passwords). It is also configured to send all traffic over the tunnel, so when, for example, they browse the internet it is just like browsing from our corporate network. The Qestion(s) So, I'm wondering how does the OpenVPN client act when the computer is already physically on the same network as the OpenVPN server? Right now, the client is configured to connect the the public dns name which will resolve to the public ip address which will NOT get reflected back to the OpenVPN server, so it is affectively blocked from connecting to the OpenVPN server while on the network. Is that a good thing? Or will it constantly try to connect, using up system resources and network resources? We will likely have hundreds of laptops regularly on the physical network with this, so it could contribute to a lot of unnecessary network chatter. Alternatively Would it be better to have the firewall reflect the port back to the OpenVPN server and let it connect? Or have our internal dns resolve the name to the private ip and allow them to connect directly? Would traffic then go over the vpn connection (which I do not want, when already on the physical network)? Or is it possible to tell it to ignore the connection when the client and server are already on the same network? TLDR What's a sane way of handling OpenVPN client running as an always-on service when the client and server will often be on the same network?

    Read the article

  • Network switches for LAN party

    - by guywhoneedsahand
    I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

    Read the article

  • System With Two Network Adapters [closed]

    - by Synetech inc.
    Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

    Read the article

  • Switch between network configurations via command line in fedora 17

    - by Mike Fairhurst
    I have two different setups I use on my work laptop; one enables synergy over an ethernet ssh tunnel with my work computer on the local network, and the other opens an HTTP tunnel to my work computer from outside the network. When I have wifi enabled at work, my laptop seems to use it by preference. This makes synergy run incredibly slowly. At home I must use wifi. I have scripts that begin my ssh tunnels, add my ssh keys, and starts up other programs like synergy, and close themselves when I shut my laptop. However, every day I have to start out my routine by opening my gnome-control-center and turning on my ethernet. I have tried route add and ifup, none of it works, so I dove into gnome-control-center's source code and found that it enabled the connection by libnm's method nm_client_activate_connection with some libnm specific structs that I am having trouble tracking down. I'm not much of a c programmer, and I'm not familiar with either GTK or libnm. Does anybody know what fedora 17 does with ethernet connections to fully enable them? Or does anybody know what libnm does to fully enable an ethernet connection? Do I have to write a c script to run libnm for me to fully emulate whatever gnome-control-center is trying to do?

    Read the article

  • Network bandwidth usage dashboard?

    - by SkippyFlipjack
    I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

    Read the article

  • Scanning to network share

    - by tking
    In our environment we have several printers with the scan to folder functionality set up. It worked pretty well. Long story short- I needed to reboot our file server one evening (the server whose $hares where all the scans go), upon on boot up I received a message stating the name of the file server (i.e AcmeFS1; Windows Server 2003) could not be used because there was a duplicate name on the network. I found that somehow another printer on the network was using the name of the file server. Weird - I know. People could no longer scan to their folders. I ran an nbtstat on the file server and found that the local netbios name table was empty. I renamed the offending printer and rebooted the file server once more. This time, no error, and once I ran nbtstat again, I found that correct name and domain in the local netbios name table. Problem is, scan to folder is still not working. I know this was working before I rebooted the file server the first time. Anyone have any idea what is going on and how to fix? Thanks. FIXED: Not sure why the reboot didnt fix it but I restarted the "Server" service on the file server and the problem went away.

    Read the article

  • Can't Ping - Wireless network of home

    - by Naunidh
    Hello, This may seem like other ping problem, but I have tried a lot before posting it here. I have a linksys WRT54G - firmware v8.00.8. I have two laptops one windows vista (192.168.1.99) and Windows Xp (192.168.1.13) connected on WiFi . The Router's IP address is 192.168.1.4, and default gateway is the ADSL modem (192.168.1.1) connected through wire. The problem is that laptops can not ping each other, they can ping the gateway and the linksys router, and both can access internet. Following has been tried (I am pinging from XP machine to Vista): I saw that arp entires for Vista machines were not being populated, so I added static ARP entries. 192.168.1.99 00-19-7e-70-d0-4e static I checked on ethereal that an ICMP packet for MAC address of Vista machine does go out from XP machine towards the Vista machine, but never reaches the Vista machine. So its get eaten by the Router? I added Vista machine to DMZ in my linksys router, so that all the ports are open (In case it was an issue). Firewalls , antivirus etc were turned off, echo was enabled explicitly on vista, file sharing, network discovery were turned on. Network type was set to private. Unchecked everything in Router;s firewall, even though they are only meant for WAN requests. Is there anything else that I should try. Thanks.

    Read the article

  • IIS_IUSRS cannot access files uploaded and created by Network Service - error 401.3

    - by Max
    Let me rephrase my question as I investigated further: The problem: I have a php script that is used to upload images on my windows webserver 2008. The files are created in the correct directory. The are created and owned by the user Network Service. Network Service has full access to the uploaded file. As soon as I try to access the uploaded file (mostly an image) via HTTP, I get an 401.3 not authorized error. Now, if I right-click on the not accessible image and grant IIS_IUSRS group read permissions via the security tab, the image can be accessed! By default IIS_IUSRS has NO access at all for the uploaded file. The directory containing the image files has the correct access rights set. But each file that is new uploaded to the directory is permitted for IIS_IUSRS. The question: How can I grant IIS_IUSRS by default access to the newly uploaded file? The appPool of the website has its identity set to its default, I also tried setting it to "networkIdentity" or so, but that did not work either.

    Read the article

  • Why can I not edit, delete directories inside of this directory

    - by user43053
    Hello there, First, I thought this was PHP related, but maybe it isn't. My original post, which may be irrelevant now is located at the bottom. The problem is I have a directory : /articles/. In it are 10 sub directories. I have been changing the permissions lately, but now it seems all the permissions of the parent folder, sub-folders and files are either chmod 755 or 777. I cannot move, delete or edit files inside of this parent directory or sub-directories with my FTP-client. I can however edit, delete, create new files and directories and change them with PHP-functions without problems. What may the problem be? OLD POST. Ignore everything below this line: If I create a directory with mkdir(), or create a file with fopen(), file_put_contents() or SimpleXMLElement::asXML(), I am unable to access the file with my FTP-client or c-Panel File Manager. If I try to delete or edit them, I get errors. Dreamweaver suggests it is a permission problem or a network or filesystem fault (but I've set the permissions with chmod() to 0777, and when I check the cPanel, it confirms chmod 777. I also tried to use fileowner() and the function returns int(99), the same owner as those files that I could access with my FTP-client. It seems files and directories created with PHP can only be modified or be deleted with PHP. I thought this must be a server setup related issue, so I write it here. I am on a shared server, and I have no idea about setting up servers. EDIT: It seems the problem is different. I cannot move files with FTP-client to the parent, or sub-directories either. This problem may not be PHP related, then. It seems the problem applies to any directory, regardless of whether it was created by PHP. EDIT 2: The parent directory has chmod 755. Thank you for your time. Kind regards Marius

    Read the article

  • Microsoft Word 2008 on the Mac sometimes "Disappears" documents, really.

    - by Ross Charette
    This happens in a computer lab environment, has happened at least 3 times. We are running Microsoft Office 2008 for mac on Leopard, everything is updated. Our user's home directories are on a network drive, but the /Library/Cache folder is running locally. Typically a student will have a Word file that they have been working on, it's been saved before they even logged onto the computer that day. They log on, open the document, click the save icon (not go to File Save), sometimes even save multiple times, then close Word. The document is now gone. It's not hidden, there are no autosaves or anything in the Cache folder. Definitely not in the trash or trashes folder. It can't find it when you click on it in 'recent documents'. Searching meticulously though every folder in their home drive turns up nothing. They look using Finder, I look ssh'd as root into their home using ls -la. I look for similar files in case they renamed it by mistake. It's gone. Disappeared. Vaporized. It's happened to at least 3 different users in the past year. Much whining. Any idea?

    Read the article

  • Win7 loses connection to network shares after resume unless server specified using FQDN

    - by Szonja Zemkó
    My Win7 client has a connection to a Linux server and its shared folders. The problem occurs when the computer wakes up after a sleep and then one of the shared folders is not accessible. I receive the following message: Error code: 80070035, The network path was not found. I have problem with one specific folder only. When I restart the computer this problematic folder is accessible again. When I log off before sleep the folder is accessible after wakeup. If I try to access the folder by using the FQDN of the server or the server IP it is also accessible. As a temporary solution I mapped the folder to a network drive using the FQDN and it's working fine but it's inconvenient since every other folder is accessible on the server. To summarize: \server\problematicshare no longer works after resume (the Samba server sees my client connect, then disconnects a few seconds later while I receive the above error message) \server\othershare works after resume \fqdn.of.server\problematicshare always works \ip.of.server\problematicshare always works once the problem manifests, I'm no longer able to restart the "Workstation" service (it is not responding) restarting the "Computer Browser" service has no apparent effect the event log doesn't contain anything that seems relevant "ping server" works

    Read the article

  • Cannot connect to a shared network drive

    - by dublintech
    I am using windows 7, I cannot connect to a shared network drive on another machine. I can ping the machine. I can remote desktop connect to the machine. The machine is on the same subnet My friend with the exact same laptop as me (and on the same network, same workgroup) can connect to the shared folder. The machine I am trying to connect to and my friends machine can both see shared folders on my machine. I also cannot see shared folders on the friends laptop. When I select diagnose, windows tells me nothing useful. When I select see details on the error pop up, I see: Error code: 0x80004005 (google doesn't help much) I can nbtstat -a the machine who has the shared folder. When I try with my firewall turned off the same happens. I have ensured my windows 7 has all updates. I run security essentials to ensure my laptop is clean. I run ccleaner to clean up my registry. Same error. I have tried with my laptop on both wireless and ethernet. As you can imagine, I am banging my head against the wall on this one.

    Read the article

  • I have just created a subnet for a local network, connecting to a standalone server on another network, now I cannot connect to the internet

    - by Seth
    I am just learning some new aspects of servers and networking. We have a network of 5 subnets that all interconnect with each-other. In order to get two computers on the subnet that we were setting up, I changed the IP from the subnet where the standalone server is on (where they used to be set up)to the local subnet we are remotely hooking up. Likewise I also changed the gateway to coincide with the new subnet. Only problem is that since doing this, I am unable to establish a connection to the internet. I can ping the server and correspong gateway & DNS server, but cannot get connected to the internet. We do have a dumb-switch (non-programmable) connected that receives both the internet and private network inputs and distributes (or should do so) to about 5 other computers. Bottom line, I cannot currently connect to the internet, and am wondering what could be causing this.. It is likely something very obvious and pardon me being more vague than I probably should be, but I could use some help resolving this! Thanks for any help!

    Read the article

  • Query total page count via SNMP HP Laserjet

    - by Tim
    I was asked to get hold of the total pages counts for the 100+ printers we have at work. All of them are HP Laser or Business Jets of some description and the vast majority are connected via some form of HP JetDirect network card/switch. After many hours of typing in IP addresses and copying and pasting the relevant figure in to Excel I have now been asked to do this on a weekly basis. This led me to think there must be an easier way, as an IT professional I can surely work out some time saving method to solve this issue. Suffice it to say I do not feel very professional now after a day or so of trying to make SNMP work for me! From what I understand the first thing is to enable SNMP on the printer. Done. Next I would need something to query the SNMP bit. I decided to go open source and free and someone here recommended net-snmp as a decent tool (I would like to have just added the printers as nodes in SolarWinds but we are somewhat tight on licences apparently). Next I need the name of the MIB. For this I believe the HP-LASERJET-COMMON-MIB has the correct information in it. Downloaded this and added to net-snmp. Now I need the OID which I believe after much scouring is printed-media-simplex-count (we have no duplex printers, that we are interested in at least). Running the following command yields the following demoralising output: snmpget -v 2c -c public 10.168.5.1 HP-LASERJET-COMMON-MIB:.1.3.6.1.2.1.1.16.1.1.1 (the OID was derived from running: snmptranslate -IR -On printed-media-simplex-count Unlinked OID in HP-LASERJET-COMMON-MIB: hp ::= { enterprises 11 } Undefined identifier: enterprises near line 3 of C:/usr/share/snmp/mibs/HP-LASER JET-COMMON-MIB..txt .1.3.6.1.2.1.1.16.1.1.1 ) Unlinked OID in HP-LASERJET-COMMON-MIB: hp ::= { enterprises 11 } Undefined identifier: enterprises near line 3 of C:/usr/share/snmp/mibs/HP-LASER JET-COMMON-MIB..txt HP-LASERJET-COMMON-MIB:.1.3.6.1.2.1.1.16.1.1.1: Am I barking up the wrong tree completely with this? My aim was to script it all to output to a file for all the IP addresses of the printers and then plonk that in Excel for my lords and masters to digest at their leisure. I have a feeling I am using either the wrong MIB or the wrong OID from said MIB (or both). Does anyone have any pointers on this for me? Or should I give up and go back to navigationg each printers web page individually (hoping not).

    Read the article

  • Lock ups, crashing, transferring files using TrueCrypt with iSCSI

    - by Anthony
    I have looked into this error and it seems that it hasn't been discussed yet - or at least I can't find any information relating. I'm having issues transferring files, usually larger files over a couple of hundred MB. Here is the setup: QNAP 410 as iSCSI Target with multiple LUNs. (CRC is turned on (Data Digest and Header Digest) Server 2003 with iSCSI Initiator version 2.08 - build 3825 (I'm copying files from anothe machine to shares on Server 2003 = into TrueCrypt volume ergo onto the NAS) I have mounted the LUN and formatted it with TrueCrypt using NTFS (Full format, not a quick one). What happens is some files, mainly RAR/Compressed files, appear as if they copy but fail. I've tested this in a number of ways and can repeat the process every time. So I thought to check transfer over iSCSI without TrueCrypt in between, a plain NTFS format - no problem at all. So it would seem TrueCrypt is at least part of the problem here. I haven't tried copying directly from the server yet, I will try that. I also haven't tried it without CRC but fail to see how that would affect this. I will update with my findings later. In the meantime does anyone have any ideas as to what could be wrong? Thanks for your time. Update: I copied a set of files, the ones I was having issues with, to the server then from there I copied those into two places within the TrueCrypt volume (Mounted on the NAS). A seperate directory create in the root of the volume The same initial directory I was using in the first instance Both worked fine. So it now seems clear that this is a link between TrueCrypt, iSCSI and Windows Shares. I say this because I originally setup the whole system using TrueCrypt volume files, not iSCSI. I changed it as it didn't suit my requirements - day wasted as well. While I had this setup though I copied my entire file set to the volume files and all files copied without error - over the network, from a pc, to the server where TrueCrypt had the volume files mounted from the NAS. I didn't bother turning off CRC on the iSCSI system as I highly doubt that is the cause in light of this finding. So any ideas?

    Read the article

  • XP shared folders not accessible after BIOS changed

    - by stijn
    Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

    Read the article

  • How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

    - by Zac B
    Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

    Read the article

  • Boosting my GA with Neural Networks and/or Reinforcement Learning

    - by AlexT
    As I have mentioned in previous questions I am writing a maze solving application to help me learn about more theoretical CS subjects, after some trouble I've got a Genetic Algorithm working that can evolve a set of rules (handled by boolean values) in order to find a good solution through a maze. That being said, the GA alone is okay, but I'd like to beef it up with a Neural Network, even though I have no real working knowledge of Neural Networks (no formal theoretical CS education). After doing a bit of reading on the subject I found that a Neural Network could be used to train a genome in order to improve results. Let's say I have a genome (group of genes), such as 1 0 0 1 0 1 0 1 0 1 1 1 0 0... How could I use a Neural Network (I'm assuming MLP?) to train and improve my genome? In addition to this as I know nothing about Neural Networks I've been looking into implementing some form of Reinforcement Learning, using my maze matrix (2 dimensional array), although I'm a bit stuck on what the following algorithm wants from me: (from http://people.revoledu.com/kardi/tutorial/ReinforcementLearning/Q-Learning-Algorithm.htm) 1. Set parameter , and environment reward matrix R 2. Initialize matrix Q as zero matrix 3. For each episode: * Select random initial state * Do while not reach goal state o Select one among all possible actions for the current state o Using this possible action, consider to go to the next state o Get maximum Q value of this next state based on all possible actions o Compute o Set the next state as the current state End Do End For The big problem for me is implementing a reward matrix R and what a Q matrix exactly is, and getting the Q value. I use a multi-dimensional array for my maze and enum states for every move. How would this be used in a Q-Learning algorithm? If someone could help out by explaining what I would need to do to implement the following, preferably in Java although C# would be nice too, possibly with some source code examples it'd be appreciated.

    Read the article

  • Open source embedded filesystem (or single file virtual filesystem, or structured storage) library f

    - by Ioan
    I'm not sure what the "general" name of something like this might be. I'm looking for a library that gives me a file format to store different types of binary data in an expanding single file. open source, non-GPL (LGPL ok) C interface the file format is a single file multiple files within using a POSIX-like file API (or multiple "blobs" within using some other API) file/structure editing is done in-place reliable first, performant second Examples include: the virtual drives of a virtual machine whefs HDF CDF NetCDF Problems with the above: whefs doesn't appear to be very mature, but best describes what I'm after HDF, CDF, NetCDF are usable (also very reliable and fast), but they're rather complicated and I'm not entirely convinced of their support for opaque binary "blobs" Edit: Forgot to mention, one other relevant question: http://stackoverflow.com/questions/1361560/simple-virtual-filesystem-in-c-c Another similar question: http://stackoverflow.com/questions/374417/is-there-an-open-source-alternative-to-windows-compound-files Edit: Added condition of in-place editing.

    Read the article

  • Silverlight 4.0: How to increase quota in Isolated File Storage

    - by xscape
    Got this line of code here but its not working. using (IsolatedStorageFile isf = IsolatedStorageFile.GetUserStoreForApplication()) { long newSpace = isf.Quota + spaceRequest; try { if(true == isf.IncreaseQuotaTo(newSpace)) { Debug.WriteLine("success"); } else { Debug.WriteLine("unsuccessful"); } } catch (Exception e) { throw; } }

    Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >