Search Results

Search found 4990 results on 200 pages for 'traffic measurement'.

Page 137/200 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

• wireshark not seeing all packets on WiFi

  - by Caffeine Coma

  I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

  Read the article

• apxs cannot install mod_cloudflare on centos

  - by Adam

  [ Linux - CentOS - Apache 2.2 - mod_cloudflare - apxs2 ] I have changed my nameservers to point to CloudFlare. The problem is that all the IP addresses are coming in as CloudFlare's. This is no good, because I have to monitor and block some specific traffic. mod_cloudflare is supposed to resolve this but I have been unable to get this installed. The command in the documentation uses apxs2. I can't figure out how to install this, or if it just means for 'apache 2.4'. I'm running 2.2.3, and I can use 'apxs'. When I run: apxs -aic mod_cloudflare.c I get the error apxs:Error: Command failed with rc=65536 Does this mean I need apxs2 or something else? How do I get mod_cloudflare working on my server? I appreciate any help, the documentation is vague and limited.

  Read the article

• how to pass domain name to backend with pound

  - by FurtiveFelon

  I am using pound as a way to decode SSL for the backend, but the bulk of the work is done on varnish (including virtualhost stuff). As a result, I need pound to just forward all other traffic to varnish verbatim, but it doesn't seem to do that. I am using the default configuration: ListenHTTP Address 1.2.3.4 Port 8080 ## allow PUT and DELETE also (by default only GET, POST and HEAD)?: xHTTP 0 Service BackEnd Address 127.0.0.1 Port 80 End End End So whenever I hit example.com:8080, it will always redirect to the default backend for varnish, which i assume was because the domain (host) header isn't send along. Anyone know what could be wrong? Thanks a lot! Jason

  Read the article

• Our GoDaddy web server is drowning in temp files!!

  - by temp file guy

  We have a virtual dedicated server with a fairly large amount of traffic. We use GoDaddy using CPanel. We have 10GIG of space of which about 80% is not our content but logs and server utilities. Godaddy support is evasive and they are trying to encourage us to migrate to new service with 15GIG. Reviewing the large files we found the following: We have a ton old TMP files at this directory. /public_html/files/TMP/FILE_PERSISTANCE_PROVIDER: (no access) some large files in these directories. /usr/local/apache/logs/ - suphp_log (220M) - access_log (7M) - error_log (5M) /usr/local/apache/domlogs/ (no access) /usr/local/cpanel/ (no access) /usr/local/cpanel-rollback /tmp Questions: What can we safely delete or truncate? How can we change permissions on files with no access to delete? Is there utility to monitor and clean up temp files Other files/programs that we can delete? thanks!

  Read the article

• Webserver: Performance impact when storing session files on /dev/shm

  - by GetFree

  I have a website runing on a typical setup: Linux, Apache, PHP, MySQL. However, what's not typical about it, is that it's getting tons of traffic (400,000+ visits a day) and so, efficiency is becoming more and more important to me. I'm constantly looking for things I could optimize and, right now, my attention is focused on PHP's session files. There's a hell lot of session files constantly being read and created on the /tmp directory. So my question is: Is it a good idea to store the session files in /dev/shm (tmpfs) in order to speed things up a little bit??

  Read the article

• Windows Firewall failing after 9-12 hours?

  - by routeNpingme

  I have 2 VM servers in the exact same NIC configuration: Server 2003 R2, one NIC connected to private (hardware firewall) network in a 10.x private address space, and one NIC connected straight to public internet. Windows Firewall is enabled for the Public Internet NIC only. Now, what doesn't make sense - this fails generally after 9-12 hours. It's not exact, but once or twice a day, traffic will just stop on the Internet NIC. No event log entries when it happens, and restarting the Windows Firewall service as well as stopping or restarting IPSec Services (just for fun) has no effect. Once the server is rebooted, everything is fine again for another 1/2 day. Any suggestions?

  Read the article

• how to? 1 domain name, 1 ISP Static IP, 1 router, 3 physical web Servers

  - by buliwyf

  I have 1 Static IP from my ISP, 58.59.60.61 I have 3 local physical web servers: Win2008 IIS 7, local IP 192.168.10.11, mydomain.com Ubuntu Apache2, local IP 192.168.10.12, subdomain1.mydomain.com Win2003 IIS 6, local IP 192.168.10.13, subdomain2.mydomain.com I have 1 domain name, mydomain.com. It is configured this way: Host(A), @, 58.59.60.61 Host(A), subdomain1, 58.59.60.61 Host(A), subdomain2, 58.59.60.61 My router is a pfSense box. It forwards all port 80 traffic to a group alias called "WebServers," which is my 3 web server IP's. This setup should work right? I believe I need to set the "host header names" in my web servers. In IIS I know how to do this. How do I do this in Apache2?

  Read the article

• Simple UPDATE query with (sometime) long query times

  - by Eric

  I run a dedicated MySQL server (2 cores, 16GB RAM) serving 100-200 requests per second. It is getting sluggish during peak traffic and I have a hard time optimizing the server. So I'm looking for some ideas now that I have done lots of Innodb fine-tuning with the "TUNING PRIMER" The query that now generates most slow queries is the following (see result from mysqldumpslow): Count: 433 Time=3.40s (1470s) Lock=0.00s (0s) Rows=0.0 (0), UPDATE user_sessions SET tid='S' WHERE idsession='S' I am very surprised to have so many long queries for such a simple query with no locking. Fyi, the table is InnoDB and has 14000 rows. It contains all active sessions on the site with approx 10 UPDATE and SELECT hits per second. Here is its structure: CREATE TABLE `user_sessions` ( `personid` mediumint(9) NOT NULL DEFAULT '0', `ip` varchar(18) COLLATE utf8_unicode_ci NOT NULL, `idsession` varchar(32) COLLATE utf8_unicode_ci NOT NULL, `datum` date NOT NULL DEFAULT '0000-00-00', `tid` time NOT NULL DEFAULT '00:00:00', `status` tinyint(4) NOT NULL DEFAULT '0', KEY `personid` (`personid`), KEY `idsession` (`idsession`), KEY `datum` (`datum`) ) ENGINE=InnoDB DEFAULT CHARSET=utf8 COLLATE=utf8_unicode_ci Any ideas?

  Read the article

• Distribute terrabyte files to the public from web server

  - by MarkJ

  Hi We need to set up a website which makes two or three large files publicly available - the files will be 1 or 2 terrabytes each. Although they will be public, in practise I expect only a relatively small number of scientists will want to download them. What is the best way to allow this? I've had a quick talk to a web-hosting provider (rackspace) and they suggested a hybrid solution. An entry-level managed server (we predict fairly low traffic for the website, but we do need to install some custom CGI software). Some cloud storage which hooks into Limelight Networks. This would host the large files, for download by FTP. It sounded OK to me but I know relatively little about server administration. Does it make sense? Thanks in advance, Mark

  Read the article

• connect to paltalk server using a proxy

  - by user40026

  Hi I want to use paltalk, which is a kind of chat software, but the ports that this applications uses are closed in my country. What I need to do is to use a proxy server. Unfortunately the software itself does not provide a proxy setting. I though it would be possible to run paltalk on an O.S. installed on a virtual machine (say virtualbox) and configure the network setting of virtual machine to direct all its traffic through a proxy on host Operating system, but I could not find a way to do so neither. can anyone please help me?

  Read the article

• Colour table cells in Microsoft Word after mail merge

  - by James

  I have an Excel spreadsheet of student data. For each of 30 topics, students are traffic lighted R, A or G (for red, amber, green) in the spreadsheet. I am mail merging individual result print-outs in Word 2010. However, rather than printing the letter R/A/G next to each topic, I would rather change the background colour of the cell to that colour. How can I do this? Is there an option with merge fields or can it be done with a macro (please provide sample code if so - I don't have experience with macros!)

  Read the article

• Source of Unexplained Requests in Server Logs

  - by Synetech inc.

  Hi, I am baffled by some entries in my server logs, specifically the web-server logs. Other than normal, expected traffic, I have noticed three types of request errors (eg 404, etc.): Broken links, ie links from old, external pages that point to pages that are no longer here Sequences of probes, ie some jerk trying to hack in by scanning my server for a series of exploitable admin type pages and such What appear to be completely random requests for things that have never existed on the server or even have anything to do with the server, and appear by themselves (ie not a series of requests like the probes) Could it somehow be a mistyped URL or IP? That’s about the only thing that I can think of, but still, how could I get a request on say, foobar.dyndns.org (12.34.56.78) for something like www.wantsfly.com/prx2.php or /MNG/LIVE or http://ant.dsabuse.com/abc.php?auth=45V456b09m&strPassword=X%5BMTR__CBZ%40VA&nLoginId=43. (Those are a few actual requests from my logs.) Can someone please explain scenario three to me? Thanks.

  Read the article

• Load balancing without a load balancer?

  - by Tom

  I have 4 nginx-powered image servers on their own subdomains which users would access at random. I decided to put them all behind a HAProxy load balancer to improve the reliability and to see the traffic statistics from a single location. It seemed like a no-brainer. Unfortunately, the move was a complete failure as the load balancer's 100mbit port was completely saturated with all requests now going through it. I was wondering what to do about this - I could get a port upgrade ($$) or return to 4 separate image servers that are randomly accessed. I thought about putting HAProxy on each image server which would in turn route to another image server if that server's nginx service was having trouble. What would you do? I would like to not have to spend too much additional money.

  Read the article

• Why do I have to manually 'Restart Management Network' on vSphere 5 host after reboot to get networking available?

  - by growse

  I've got a couple of vSphere 5.0 hosts in a small lab environment here and I've noticed a strange behaviour. When on of the hosts gets rebooted, it is unresponsive to the network until I log into the ESX console, Press F2 to customize and select Restart management network. Once this is done, the networking works perfectly as expected. Each host has two NICs which are trunked together using Etherchannel to a Cisco 3750. The link is also a .1q VLAN trunk and the management network is configured on VLAN121 with the VM traffic configured on VLAN118. Why would the host be completely dead to the world until I physically kick it? Edit Sample switch config for trunk: interface Port-channel2 description Blade 1 EtherChannel Trunk switchport trunk encapsulation dot1q switchport mode trunk end ! ! interface GigabitEthernet4/0/1 description Bladecenter1 CPM 1A switchport trunk encapsulation dot1q switchport mode trunk speed 1000 duplex full channel-group 2 mode on end Vswitch teaming settings: Management port group settings:

  Read the article

• network user isolation

  - by seaquest

  My question is for a network with a Linux iptables router gateway. How can it be possible to prevent inter-network traffic of those users. Think this case as a public network, IPs are distributed through linux gw and users are authenticated thru the gateway. We want to protect public users from public users. Network is not wireless and I can not use Wireless AP user isolation. Actually I have a simple method. Subnet the network into /30 mask. Give minimum IP of each subnet to the gateay and ditribute those /30 IPs from the subnet. But this is pretty costly for such an aim. I want to ask for other methods Thanks.

  Read the article

• Do I really need twho different Exchange servers 2007|2010?

  - by lrosa

  Given am Exchange Server 2003 running on a dedicated server on a LAN protected by a Linux in DMZ, Microsoft says that if you upgrade, you should install two different servers (meaning two boxes, two licenses of Windows Server and two installations of Exchange) with different Exchange "server role". Exchange is installed in a safe LAN, there is a Linux relay in DMZ that feeds messages to Exchanges and gets from it the messaged to be delivered on the Net (smart relay). The mail traffic is about 2000 Internet messages/day and probably another 2000 msg/day sent by local users within the organization. The servers hosts 200 users.

  Read the article

• Virtual environment firewall with CSF + iptables rules on VM?

  - by luison

  We are getting into virtualization with a Proxmox VE (OpenVZ + KVM) server. Our plan for firewall is to have CSF (http://configserver.com/cp/csf.html) running on the host machine as we've had a reasonable good experience with it in the past. Apart from that we plan simple firewall rules on the VM machines (mostly OpenVZ containers with same kernel) and maybe fail2ban simple specific rules. I would appreciate comments with anyone with similar experiences? I understand all traffic comes via the host machine so a combined firewall there with specific firewalling on the VM should work, alltough some iptables rules are hard to get to work on OpenVZ containers.

  Read the article

• Connecting PPTP VPN with Ubuntu 9.10

  - by Christian P.

  I have an ubuntu machine that I wish to connect to a VPN and have traffic routed through that. So far I have installed the pptp-linux package and tried my hand at configuring it manually as well as using pptpsetup. I am using Ubuntu 9.10, but regardless of the method I get "Couldn't find MPPE kernel support". Searching a bit for the problem seems to reveal that Ubuntu DOES come with MPPE kernel support (and has done for quite some time). If anyone can figure this out, you'd be a real lifesaver!

  Read the article

• SQL 2008 R2 3rd Party Peer-to-Peer Replication, Global Site Distribution

  - by gombala

  We are looking at hosting 3 globally distributed SQL Server installations at different data centers. The intent is that Site A will serve web traffic and data for a specific region, same with Site B and C. In the case that Site A data center goes down, looses connectivity, etc. the users of Site A users will fail over to Site B or C (depending which is up). Also, if a user from Site A travels to Site C they should be able to access their data as it was on Site A. My questions is what SQL replication technology (SQL Replication or 3rd party) can support this scenario? We are using SQL 2008 R2 Enterprise at each site, each site runs on top of VMWare with a Netapp filer. Would something like distributed caching help in this scenario as well? We have looked at and tested Peer-to-Peer replication but have encountered issues with conflicts during our testing. I imagine there are other global data centers that have encountered and solved this issue.

  Read the article

• Software to measure the speed of http browser connections

  - by Dan Revell

  I'm trying to gather some ammunition about my ISP and it's aggressive traffic shaping of particular websites. So I'm looking for an application that will allow me to see what speeds I get to particular websites. I want to open a browser connection to a particular video streaming website for example and see the speed of the connection that gets made, be it http or plain tcp. I'm after something along the lines of TCPView but unfortunately this doesn't include transfer speeds. I'm half tempted to write one myself but hopefully something will already be out there that does the job.

  Read the article

• Distributed Nagios Installation

  - by kruczkowski

  I'm looking for a plug-in or product that will act as a remote probe and perform tests then send back the results to the central Nagios server. Reason for this is that I'd like to monitor internal systems and servers at customers, but don't want to allow all the traffic passing the firewalls. Ideally I'd like a soft-probe that would be installed and then perform the tests and send back the results (via SSH) to the central Nagios installation. Does anyone know of a product or plug-in that would offer such service? If not Nagios, is there any other monitoring system that does such a thing (ideally open-source)?

  Read the article

• Virtual firewall to protect hypervisor

  - by manutenfruits

  I am running an Ubuntu Server 12.10 as a single host connected to a NATed router connected using PPPoE to a optical fiber modem. This server is meant to be accessed from the Internet, but also to be used from the LAN as a SVN, MySQL and what not... The issue is that the router is not customizable enough to serve, so I was thinking about creating a virtual pfSense firewall using KVM inside of the server itself, removing the need of the router. Is this possible? Can the host ignore and block all traffic coming to itself, but not for the firewall? I am aware this is not the most desirable environment, I accept suggestions based on budget!

  Read the article

• Load balancing with Cisco router

  - by you8301083

  I have a Cisco router with two bonded T1's which are setup as a VPN to the main office. We need more bandwidth but can't get other connections (or it's too costly), so I would like to have a dsl connection installed. This DSL connection will run over a VPN to the same main office, but it won't be bonded with the T1's - so it won't act as a single connection. Since the three circuits won't act as a single connection (basically would be two connections 2 T1's + 1 DSL) we would have to split the network in half - but I don't want to do that. Instead, would it be possible to send all HTTP/HTTPS over the DSL connection but send all mission critical data (such as voice/active directory) over the T1's? I basically want to send specific ports over DSL and everything else over the T1's without separating half of the users traffic over the DSL and the rest over the T1's.

  Read the article

• Blocked connections passing through firewall. What is wrong?

  - by Kiranu

  In our company we have a small business router (Cisco RV082) on which we are using its standard configuration (block all incoming traffic). We also have an SMTP relay configured (using WS2008R2) so that our internal applications can send email through google apps (which requires authentication). The thing is that the server was being used to send spam. We fixed the problem by only allowing the server to relay email from our internal IP address range (10.0.0.0/16). My concern is that there was a way by which external IPs connected to the network and that underlying problem has not been fixed, but I cannot imagine how these machines connected. Any thoughts?

  Read the article

• Where do yum-updatesd dbus messages go on Centos-5.7?

  - by dsadinoff

  I'm unfamiliar with dbus and friends. Centos 5.7 seems to ship with yum-updatesd sending messages to dbus. I have a feeling I should just change that to email and be done with it, but I'd like to understand why it's configured that way. Where do the messages go from dbus? Is something subscribed? Are they queueing inside dbus somehow? How could I figure this out on my own? /etc/dbus-1/system.d/yum-updatesd.conf seems to configure dbus to allow for traffic from root on the edu.duke.linux.yum interface, if that helps.

  Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >