Search Results

Search found 4990 results on 200 pages for 'traffic measurement'.

Page 138/200 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• ISCSI: Ethernet cable maximum length vs. SCSI command timeout

  - by Jeremy Hajek

  I have a question about a non-optimal setup and the practical implications of this. Ideally you would place the ESXi server right in the same room as the FreeNas white box end of question. My situation is this: I have a run of ~125ft of Cat 5e connecting a ESXi server to a FreeNas whitebox in the server room. I know the distance of the ethernet cable is within the maximum distance for ethernet traffic but I have two questions... Can Cat 5e support gigbit speeds at that distance if the switch on the back end is a linksys SRW-2048? Should I be concerned about the distance causing data read and write timeouts in the SCSI portion--(disk operations of the ESXi)?

  Read the article

• Routing table change to access Internet over mifi

  - by Randall Blake

  I have two networks at home. One uses a Verizon mifi wireless on 192.168.1.1. The other uses a dlink router on 192.168.0.1. I have one laptop with two nics, one wireless and one not. The wireless nic connects to the mifi. The Ethernet nic connects to the dlink router. It's ip is 192.168.0.2. I also have a laptop with only one nic connected to the dlink on 192.168.0.3. I want to connect laptop 2 to the Internet. Can I do that by adding an entry to the routing table so that destination 0.0.0.0 routes to 192.168.0.2? If I do that, will laptop 1 "know" that it should route traffic from 192.168.0.3 to 192.168.1.1? Thanks for any assistance.

  Read the article

• Modern open source NIDS/HIDS and consoles?

  - by MattC

  Years back we set up an IDS solution by placing a tap in front of our exterior firewall, piping all the traffic on our DS1 through an IDS box and then sending the results off to a logging server running ACiD. This was around 2005-ish. I've been asked to revamp the solution and expand on it and looking around, I see that the last release of ACiD was from 2003 and I can't seem to find anything else that seems even remotely up-to-date. While these things may be feature complete, I worry about library conflicts, etc. Can anyone give me suggestions for a Linux/OpenBSD based solution using somewhat modern tools? Just to be clear, I know that Snort is still actively developed. I guess I'm more in the market for a modern open-source web console to consolidate the data. Of course if people have great experiences with IDS' other than Snort I'm happy to hear about it.

  Read the article

• Regression testing for firewall changes

  - by James C

  We have a number of firewalls in place around our organisation and in some cases packets can pass through four levels of firewall limiting the flow TCP traffic. A concept that I'm used to from software testing is regression testing, allowing you to run a test suite against a changed application to verify that the new changes haven't affected any old features. Does anyone have any experience or an offer any solutions to being able to perform the same type of thing with firewall changes and network testing? The problem becomes a lot more complicated because you'd ideally want to be originating (and testing receipt) of packets across many machines.

  Read the article

• Windows Virtual PC File Copy from host very slow

  - by Shiv Kumar

  I have a Windows 7 desktop on which I've installed Windows Virtual PC and an instance Windows 7. I also have virtual XP instance on the same host. The problem I am having is that copying files from the host to the virtual machine is dog slow. I'm talking 17KB/sec. The host machine has a gigbit NIC. While using the XP virtual instance to do the same I didn't notice a huge difference but on the Window 7 virtual instance the time is really slowing me down. Is there something I need to do (settings) to fix this? I've attached an image of the Resource monitor (of the virtual Windows 7 instance) that shows my network traffic going in bursts rather than relatively steady. The files are on a "public" folder on my host machine.

  Read the article

• How to build an outbound load balancer with linux?

  - by matnagel

  We have a small house in the countryside and there is no fixed broadband, so we had a mobile flatrate first, and for 2 people with 2 computers it was too slow, so now we have 2 flatrates for 2 client machines. So I pay 2 flatrates and have double bandwith theoretically. There is a local network in the house that connects everything. But when I am alone I wonder how I can use both connections at the same time. I want to build a solution where I can browse the web and page requests are spread between the 2 connections. I imagine there are expensive routers who can split the traffic between 2 lines. But is there a good way to do it with linux? The solution I am looking for will split the requests already for one page (multiple images, css files, javascrfipt files) between the two lines.

  Read the article

• Hosting services on ubuntu server VM

  - by Trevor Hartman

  I've got OSX Server running on a macbook, and I'm looking to run an ubuntu server VM on it via Parallels. I'm thinking about hosting all my apache inside linux, and possibly some other services. I'm curious what a viable config would be, having not done this before. I need to do bridged network right? How do I direct web traffic to the VM instead of OSX? Haven't got my head wrapped around how this works yet so any help would be appreciated.

  Read the article

• Can a webite have too many bindings?

  - by justSteve

  IIS7.x on a win08 web version on a dedicated server. I have a site that's serving a few dozen affiliates - many of which are hitting me via a subdomain from their own root domain - all of which have a subdomain specific to their account. E.G. my affiliate named 'Acme' hits my site via: myApp.Acme.com (his root, my app) Acme.MyDomain.com (his account within my root domain) Currently I'm adding each of these as a binding entry in IIS (targeting a discrete IP, not '*'). As I ramp this up to include more affiliates I'm wondering if I should be concerned about how many binding this site handles. Proabaly, in Acme's case I can do without the 'Acme.MyDomain.com' because, in reality, all traffic takes place via myApp.Acme.com. Mine is a niche site - very volume compared to most. At what point do I worry about all those bindings? thx

  Read the article

• Proxying fake domain to a localhost port

  - by Trevor Burnham

  I'd like to do much the same thing described at Redirect Domain Name to Localhost for web app development purposes, but with the twist that I'd like requests to fakedomain.com:80 to be routed to localhost:8080, say, so that I don't have to actually use my development machine's port 80. I'd welcome answers that take the form of: Small changes to configuration files like /etc/hosts, and/or An easy-to-configure proxy server I could run Note: Pow takes the approach of setting a firewall rule to forward all incoming traffic on port 80 to port 20559. That may be an acceptable solution, but ideally, I'd like to forward only a specific domain + port combination.

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• ASP.NET MVC multi-instance session management on amazon ec2

  - by gandil

  I have a web application written in asp.net mvc2. Currently hosted on amazon cloud ec2. Because of growing traffic we want move multi instance enviorenment. I have a custom session class which currently initiate at session start (global asax) and i am using via getter or setter class in application. Because of multi instance chore i have to handle hole security architecture. I am looking a better way to handle this problem. I am looking for good implementation of session and how to apply on amazon ec2 multi instance environment. What is road blocks for system architecture?

  Read the article

• Forwarding 80 to 443 on Nagios woes

  - by Ethabelle

  I perhaps just need some extra insight because I don't see where I'm going wrong. I used an SSL Cert to secure our nagios server. We want to specifically require all traffic over nagios (like 2 users, lol) to use SSL. So I thought, oh, mod_rewrite + Rewrite Rule in .htaccess, right? So I went into the DocumentRoot and did a vi .htaccess (one didn't already exist) and then I put in the following rule; RewriteEngine On RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://our.server.org/$1 [R,L] This does absolutely nothing. Does nada. Whhhyy.. Note: AllowOverride all in httpd.conf is on. Also, I verified that the module is not uncommented out ... but note, I couldn't find the mod_rewrite module installed so I copied it over from another server and placed it in modules/mod_rewrite.so . It was weird because it was enabled in the httpd.conf file, but then didn't exist in modules ... I'm a baddie :(

  Read the article

• ip routes to specific interface

  - by user65053

  I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• How are my DNS entries safe in a shared hosting environment?

  - by Jake

  I'm trying to understand how DNS works in a shared hosting environment. I went to my registrar and set my name servers to my host's ns1.foo.com and ns2.foo.com. I'm using a cloud hosting provider who has a web portal where I can set my DNS entries. However I am confused by the lack of security. when I entered in the entries for my domain there was never any step to prove that I actually own that domain. What is to stop somebody else on the same hosting service (a nasty neighbor) from writing over my DNS entries and pointing my traffic to their server instead?

  Read the article

• Very High Network out in ec2 instance

  - by Jatin

  I launched an ubuntu-14.04-64bit instance in Amazon EC2 two days back. And I started Tomcat 7.0.54 in that instance and deployed my application war files. It has no other software installed other than tomcat and the default ones. In the past 2 days, its shows 858 GB of Data Transfer(Network Out) from that instance. I have attached a graph of Amazon CloudWatch Metric "Network Out" My application does not do any data download/upload. Its a Java Spring application and the front end is in HTML&Javascript. My application traffic was very low (less than 20 hits) in those 2 days. Is there a way to find out why these data transfers happened and also to find what data has been transferred. If you can see in graph, network out was 20gb per minute. Some more info: Network in was negligible CPU Utilization was very high Everything else was low

  Read the article

• Cisco IOS router config -- how to disable SSH / SNMP on all but loopback address?

  - by chris

  Sorry for the naive question; a quick reading of the cisco docs doesn't answer this question... So I've got a router (say for the sake of argument a 4500 running IOS 15.x) It has interfaces in 3 different subnets -- 10.0.0.1/24, 10.0.1.1/24, and 10.0.2.1/24 It also has a loopback address of 172.16.0.33 How do I make it so that SSH / SNMP and other administrative traffic works on the 172 address but doesn't work on the IP addresses I wish to only use for L3 forwarding? Ideally this can be done by disabling the control plane access to these interfaces not just by using an ACL, but whatever, I don't actually care that much as long as it works... Thanks!

  Read the article

• apache requests failing

  - by Josh

  I'm trying to figure out why sometimes the client fails to load objects/requests from a dynamic page served from Apache/MySql/Debian machine. Let's say 13 objects are to be loaded for a total of 185.3 KB load, with no external objects (no DNS lookups) and no other traffic at the same time, randomly some of those object do not load. However, if I perform a refresh, sometimes all of them load or some might fail again. I only have 1Mbps/up and my DNS is been hosted externally (everydns). What could be the reason of this issue? Any comments will be appreciated.

  Read the article

• Squid - Selective reverse proxy and forward proxy

  - by Dean Smith

  I'd like to setup a squid instance to do selective reverse proxy for a configured list of URLs whilst acting as a normal forward proxy for everything else. We are building new infrastructure, parallel live as it where, and I want to have a proxy that people can use that will force selective traffic into the new platform whilst just acting as a forward proxy for anything else. This makes it very easy for people/systems to test the portions of the new platform we want without having to change too much, just use a proxy address. Is such a setup possible ?

  Read the article

• Port Redirection on Mac OS X Lion

  - by Andreas

  I have tried to solve this issue using pf but with no luck. Basically, I am trying to redirect incoming port 443 traffic to port 22. I have tried to set up a rule in a file and load it in pf but I get syntax error. Can anyone with more experience with pf provide some insight? Here's what I've attempted: pass in on en1 proto tcp from any to any port 443 rdr-to 127.0.0.1 port 22 and pass in quick proto tcp to port 443 rdr-to 127.0.0.1 port 22 I've been able to do this in MacOSX Snow Leopard with ipfw: sudo ipfw add 1443 forward 127.0.0.1,22 ip from any to any 443 in but it doesn't work in Lion (it gives me an Invalid Argument error).

  Read the article

• Setting a wireless access point on Ubuntu server 11.10

  - by Solignis

  I am trying to setup a wifi access point with my Ubuntu server. I have managed to get my phone to connect the wireless and now it get a DHCP lease. Though it still cannot ping out or get pinged by anything on my network. I am prety sure my problem is iptables, but I not sure what would be wrong. Here is what my rules look like. (The ones pertaining to the bridge interface) # Allow traffic to / from wireless bridge interface iptables -A INPUT -i br0 -j ACCEPT iptables -A OUTPUT -o br0 -j ACCEPT I am guessing my rules are a little lean, the bridge exists on the same subnet as everything else on my network, I am using a 10.0.0.0/24 subnet. EDIT Oh yeah I should mention also, when I do a ping test, I get Destination Host Unreachable as the error.

  Read the article

• 27 days after domain transfer name servers not propogated

  - by Thom Seddon

  We recently bought the domain: embarrassingnightclubphotos.com 7 days after accepting the transfer the domain finally transferred to our registrar and we immediately changed the name servers from ns*.netregistry.net to amy.ns.cloudflare.com and cody.ns.cloudflare.com 20 days after changing the name servers, the majority of tests show that both old and new nameservers are still being reported: http://intodns.com/embarrassingnightclubphotos.com http://www.whatsmydns.net/#NS/embarrassingnightclubphotos.com We are now ready to launch the new site but this issue is plagueing us as a high proportion of the traffic is still receiving the old nameserves and so hitting the old server. You can tell if you have hit the old or new server as the old server has the value "A" for the meta tag "Location" and the new server has "U". (The old server just has an iframe too!) I have never had this problem before - who is causing this and how should we go about reaching a resolution? Thanks

  Read the article

• Mikrotik queues and limiting total upstream bandwidth

  - by g18c

  With a Mikrotik router (form of embedded Linux) I have created simple queues per machine matched by source IP address. Each of the 4 machine queues has an unlimited burst 3Mbps/3Mbps for Tx/Rx. During speedtest.net on all 4 machines at the same time, each machine shows 3Mbps (and is limited correctly there), however the total bandwidth on the uplink goes to 12Mbps (i need to set this to 10Mbps max for the upstream). I want to restrict the actual traffic passing across the uplink port to 10Mbps regardless of what the other queues are doing (I need this catch all queue to have the final say on the uplink speed). For example I need: Scenario A Machine A transferring @ 3Mbps Machine B transferring @ 3Mbps Machine C transferring @ 3Mbps Machine D transferring @ 0Mbps Up-link speed = 9Mbps Scenario B Machine A trying to transfer @ 3Mbps Machine B trying to transfer @ 3Mbps Machine C trying to transfer @ 3Mbps Machine D trying to transfer @ 3Mbps Up-link speed = 10Mbps Actual transfer speed of machine A,B,C,D = 2.5Mbps This is to allow slight over subscription of bandwidth queues as not all will be transmitting at 3Mbps all the time. Is this possible and if so how would one go about doing this?

  Read the article

• Why do some web servers not respond to icmp requests?

  - by John Himmelman

  What is the purpose of blocking/dropping inbound ICMP traffic on a public web server? Is it common for it be blocked? I had to test if a server was accessible from various locations (tested on various servers located in different states/countries). I'd rely on ping as a quick & reliable method of determining if a server was online/network-accessible. After not receiving a response on a couple boxes, I tried using lynx to load the site, and it worked.

  Read the article

• Sharing VPN from XP to Linux virtual

  - by user55513

  Hi I will keep the question simple with few details, if more is needed tell me. Thanks. I am playing around with networking and virtualbox. So I have 2 virtual machines. One is windows xp and another has linux in it. Windows XP has 2 network cards. One for the internet and the other to connect to the linux computer. Linux has one 1 card and it can only access the internet passing through Windows XP. Internet works fine until I activate OpenVPN on Windows. When I turn on VPN, Linux has no access to it. How can I make linux use VPN too? I believe it has something to do with using the "route" command on XP to send VPN traffic to Linux but I was not able to figure it out how yet.

  Read the article

• How can I debug Cisco Firewall ASA "Dispatch Unit" very high CPU utilisation from ASDM?

  - by Andy

  I have recently had my first firewall installed so I am very new to this whole situation. I am finding that Dispatch unit is becoming overloaded and it would appear to be the reason I get serious bouts of lag on my server. The firewall has had little configuration apart from me blocking all the ports in "Access Rules" and allowing only the ones the server needs and from where it needs them. I guess what I am after is assistance with locating the issues causing "Dispatch Unit" to take up all the CPU Regards --Edit-- With ASDM statistics I found that packets inbound (peak of 70-100k/sec from <1k/sec normal), traffic inbound (peak of 40-50kbits/sec from <1kbits/sec normal) and CPU all peak at the same time so I am pretty sure it is an attack of some sort but as a beginner with ASA I am not sure how to resolve

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >