Search Results

Search found 4503 results on 181 pages for 'logical operator'.

Page 138/181 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Is there a reason to use internal DNS over 8.8.8.8 ?

  - by skylarking

  I've inherited a LAN where there is really no name resolution being done for local resources... i.e. all users enter IP addresses manually to access printers and network shares. There are no LDAP servers or domains either....workstations simply connect to the network without authentication. DHCP is handled via a core switch... And DNS settings are also handed out by this same core switch. Currently, the DNS assignments are as such, and in this order: 10.1.1.50 / old Pentium III Windows 2003 box running DNS service- 128 MB RAM 169.200.x.x / ISP 4.2.2.2. / the well known public one There a couple thousand clients on the LAN....and most of the activity is web browsing ( this is an educational setting ). First of all, the server seems woefully underpowered for this task...yet there is virtually no slowness when web surfing by clients.... How much horsepower should a heavily used DNS server have ? I have also heard using 4.2.2.2 is a bad idea .... since it has been so overused... Finally, wouldn't it make sense to have a robust external DNS server listed first? ( Google's 8.8.8.8 would seem to be a logical candidate )

  Read the article

• how to uninstall ubuntu 8 from ubuntu 10 dual boot

  - by umar

  I have ubuntu 8.04 and ubuntu 10.04 on my laptop, and i want to reclaim all the ubuntu 8 space so that i have just one operating system on my laptop. how can i do it? the output of sudo fdisk -l is as follows: sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x31a431a3 Device Boot Start End Blocks Id System /dev/sda1 * 1 4959 39833136 83 Linux /dev/sda2 4960 5233 2200905 82 Linux swap / Solaris /dev/sda3 5234 12852 61192552 83 Linux /dev/sda4 12852 19458 53062657 5 Extended /dev/sda5 12852 19182 50847744 83 Linux /dev/sda6 19182 19458 2213888 82 Linux swap / Solaris i dont know which of sda1, ..., sda 6 etc ubuntu 8 is on. how can i find that out? The actual task is that i think a lot of space is devoted to ubuntu 8, if there is no easy way to get rid of it, then i want to repartition the disk so that about 50 GB of hard disk space is given to ubuntu 10's home folder from the ubuntu 8's home folder. but i hope that there is an easy way to get rid of ubuntu 8 alrogether and just have ubuntu 10 on my system.

  Read the article

• OS/X 10.6 Bizarre login bug: Making alternative "Others..." appear. Why does this happen?

  - by bjornl

  I am studying at NUS in Singapore, and they have a mac-equipped computer lab here at school. All users (students) have our own personal accounts that we use to log in to the computers with. Sometimes when you approach a computer to log in only the alternative "thinkmac", which is the school's administrator account, I presume. Some other computers have the alternative "thinkmac" as well as "Others..." where you can input your own login credentials. One day as I sat down by a computer and there was only the "thinkmac" alternative. I was about to get up and find another one when the guy sitting next to me says - Just click 'thinkmac' - the computer will ask for your password - then hit escape to get back to the login screen. Repeat until "Others..." appear. So: If you click any user account, hit ESC to get taken back to the login screen, repeat for 5-10x, eventually the alternative "Others..." will appear. Why is this? Is there an internal counter that keeps track on how many times you have clicked a/any given user account, and after a certain threshold it displays the "Others"? What is the logical reasoning behind this?

  Read the article

• CouchDB crashes at startup when path to config file has space(s)

  - by Barry Wark

  I'm hoping to run CouchDB as a per-user Launch Agent on OS X. I'm using the coucdbx-core folder from the CouchDB Server.app as the base of my CouchDB deployment. I'd like each user to have their own couch instance (on a different port), necessitating separate config files for each instance. The logical place to put these files is in ~/Library/Application Support/ for each user. I can put the entire distribution in ~/Library/Application Support/my-app/coucdbx, and put the .ini at ~/Library/Application Support/my-app/local.ini. Starting couchdb as bin/couchdb -a ../local.ini (from ~/Library/Application Support/my-app/coucdbx) works great. But I'd like to save every user the ~50MB couchdbx and install the couchdbx-core in a shared location (e.g. within my app's .app bundle). When I do this, the path to the per-user config file contains a space, and I get the following error when starting CouchDB: $ bin/couchdb -n -a ~/Library/Application\ Support/us.physion.ovation/default.ini {"init terminating in do_boot",{{badmatch,{error,{bad_return,{{couch_app,start,[normal,["/Users/hs/prj/build-couchdb/build/etc/couchdb/default.ini","/Users/hs/prj/build-couchdb/build/etc/couchdb/local.ini"]]},{'EXIT',{{badmatch,{error,{error,enoent}}},[{couch_server_sup,start_server,1,[{file,"/Users/hs/prj/build-couchdb/dependencies/couchdb/src/couchdb/couch_server_sup.erl"},{line,56}]},{application_master,start_it_old,4,[{file,"application_master.erl"},{line,274}]}]}}}}}},[{couch,start,0,[{file,"/Users/hs/prj/build-couchdb/dependencies/couchdb/src/couchdb/couch.erl"},{line,18}]},{init,start_it,1,[]},{init,start_em,1,[]}]}} Is there any way to provide a config file at the command line, if that config file's path includes space(s)? Despite my best efforts in the mailing list archives, wiki and google, I haven't been able to find a solution or a definitive "it can't work". Any help greatly appreciated.

  Read the article

• Formatting an HP ProLiant dl380 G4

  - by i.h4d35

  I have an old HP ProLiant dl380 G4 server whose hard disk needs to be formatted. Unfortunately, I cannot seem to do so. For one, it doesn't seem to be detecting any Hard Drives attached to the Server. The Hard Disks show up in the Ctrl+A option (SCSI Configuration Utility). Also, while inserting the SmartStart CD (7.01 or 7.04), it shows a message that no logical drives are found and there aren't any options to create one. Alternately I've tried slipstreaming the SCSI Driver into the OS but that doesn't seem to be helping. Also, I have a USB Floppy drive (for the SCSI driver) but that doesn't seem to be detected. Also, directly installing the OS (MS Server 2003 Standard Edition) obviously doesn't work (shows no hard disk found) Could anyone please advise as to what other needs to be done to format my server? Also please tell me what are the possible errors/mistakes which've been made so that I can learn from them. I went through some questions here on ServerFault and the HP guides here but they weren't of much help to a n00b like me. Thanks in Advance.

  Read the article

• Steps after installing vCenter Server?

  - by goober

  I'm working with: Two new ESX servers that I'm configuring A new Server 2008 R2 machine that I'm using for vCenter. I took the following steps: Installed the Hypervisor on the 2 ESX machines Checked their setup/connectivity (appears to be fine; can ping, etc.) Installed vCenter Server on the Win2k8R2 box. This included the install of a SQL Express database (we're a small shop) FYI, I changed some of the ports (443 -- 8443, 80 --8080, etc.) Installed vCenter Web Client Server on the Win2k8R2 box Problems my vSphere Client on my Desktop fails to connect. Part of this is that it asks me for a username and password, but I don't recall specifying one when I set up the install. I receive the error "vSphere Client could not connect to [machinename]. An unknown connection error occurred. (The request failed because of a connection failure. (Unable to connect to the remote server))" I have also tried to use local machine admin credentials, including the format machinename\localuseracct. I have also tried using my domain credentials which are an admin for that box. I have also checked and the service is running. I also tried to connect via vSphere client locally installed on the server. It translates "localhost" to the correct name but gives the same error. I cannot register the vCenter server from the vCenter Web Client Server. I'm not sure if this is necessary, as they're both on the same machine, but it seems like the logical next step. I also receive a "failed to connect" error in this case as well. FYI, both the vCenter server and the vCenter Web Client Server are installed on the same Win2k8R2 server. What am I missing here? What is the best way to test in this case?

  Read the article

• How do you monitor SSD wear in Windows when the drives are presented as 'generic' devices?

  - by MikeyB

  Under Linux, we can monitor SSD wear fairly easily with smartmontools whether the drive is presented as a normal block device or a generic device (which happens when the drive has been hardware RAIDed by certain controllers such as the one on the IBM HS22). How can we do the equivalent under Windows? Does anyone actually use smartmontools? Or are there other packages out there? The problem is that SCSI Generic devices just don't show up in Windows. If the drives aren't RAIDed we can see them fine. How I'd do it in Linux: sles11-live:~ # lsscsi -g [1:0:0:0] disk SMART USB-IBM 8989 /dev/sda /dev/sg0 [2:0:0:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg1 [2:0:1:0] disk ATA MTFDDAK256MAR-1K MA44 - /dev/sg2 [2:1:8:0] disk LSILOGIC Logical Volume 3000 /dev/sdb /dev/sg3 sles11-live:~ # smartctl -l ssd /dev/sg1 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 26~ Percentage Used Endurance Indicator |_ ~ normalized value sles11-live:~ # smartctl -l ssd /dev/sg2 smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.32.49-0.3-default] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net Device Statistics (GP Log 0x04) Page Offset Size Value Description 7 ===== = = == Solid State Device Statistics (rev 1) == 7 0x008 1 3~ Percentage Used Endurance Indicator |_ ~ normalized value

  Read the article

• Search for files after a relative date using Windows search

  - by Zoredache

  I am looking for a way to save a search that includes a relative date. Specifically I am looking for a way to save a search that matches files that have a modification date that is 7 days ago. I have read the Windows Search Advanced Query Syntax document and I am not seeing a way to say 7 days ago. The numbers and ranges section does mention that relative dates are possible. The problem is that the relative dates described there do not fit the criteria I need. The lastweek almost looks like what I want except if I run a query like after:lastweek on a Monday it will only show my file that have been modified since Sunday at 12:00. The lastweek/lastmonth seem to relative to the start of the week/month which is not what I need. Multi-word relative dates: week, next month, last week, past month, or coming year. The values can also be entered contracted, as follows: thisweek, nextmonth, lastweek, pastmonth, comingyear. One nice thing about saved searches is that they are stored as an XML document and the file format is documented. I am not seeing how to form a correct value for a datetime. If I was able to understand this format, I suspect I could use a text editor and created a saved search that does what I want. Fragment from the examples: <conditions> <condition type="leafCondition" valuetype="System.StructuredQueryType.DateTime" property="System.DateModified" operator="imp" value="R00UUUUUUUUZZXD-30NU" propertyType="wstr" /> </conditions> To summarize I am looking for an answer to one or both of these questions How do I make a query for '7 days ago' using the standard syntax? How is the DateTime stored in a saved search?

  Read the article

• CD-ROM Cant Be Accessed After Installing VMware Tools on VMware Server 2.0.2

  - by Optimal Solutions

  Using VMware Server 2.02, I set up a new VM (Windows XP Pro) applied all of the updates, added Windows addons from the install CD, etc... I got it to a stable point and up through that point I was able to access the CD-ROM drive (E: on my host). What I never did before was install "VMware Tools" and since it claims to give better mouse and video support, I gave it a shot. What it does is it places the install package in a virtual CD-ROM drive. I ran the install, no errors and it wants a reboot. I log back in after reboot and pop in the install CD for Microsoft Office 2003 and I receive the message "Please Insert A Disc Into Drive D:". Drive D: would be the next logical drive after the C: drive where I chose to install the OS. The message box sits there and if I click "Cancel", to return to Windows Explorer, the status bar seems to blink ever 1/2 second - as if its polling for a CD-ROM drive or something. No bangs or exclamations in the Device Manager for any hardware. I had taken a snapshot prior to the VMware Tools install and upon restoring it, the CD-ROM is back. I made copies of two other VMs, installed the VMware Tools on those VMs and both experienced the same issues: Windows 2003 Server and Windows 7 (32-bit). Has anyone seen this issue and know of a fix for this? It would be nice to have the better graphics and better mouse control AND use my CD-ROM drive as well! Thank you.

  Read the article

• Poor Write Performance in VM inside Proxmox PVE 2.0

  - by sorsenne

  I am running a PVE 2.0 on a decent Hardware (2 SATA HDDs as RAID1, 12GB RAM, i7 CPU) but the I/O Performance is very poor inside the VM (Ubuntu 11.10 Server). The very same VM was copied to another Server running simply Ubuntu Server with KVM and had better I/O Perf. this is how the HDD is shown in the Guest: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) ata1.00: ATA-8: ST3000DM001-9YN166, CC49, max UDMA/133 ata1.00: 5860533168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC49 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I tested with DD: $ dd bs=1M count=128 if=/dev/zero of=test conv=fdatasync 128+0 records in 128+0 records out 134217728 bytes (134 MB) copied, 19.2222 s, 7.0 MB/s on the Host, this same Test will result with 156 MB/s in average. PS: I am using VirtIO and see no error in dmesg.

  Read the article

• Very slow write performance on Debian 6.0 (AMD64) with DMCRYPT/LVM/RAID1

  - by jdelic

  I'm seeing very strange performance characteristics on one of my servers. This server is running a simple two-disk software-RAID1 setup with LVM spanning /dev/md0. One of the logical volumes /dev/vg0/secure is encrypted using dmcrypt with LUKS and mounted with the sync and noatimes flag. Writing to that volume is incredibly slow at 1.8 MB/s and the CPU usage stays near 0%. There are 8 crpyto/1-8 processes running (it's a Intel Quadcore CPU). I hope that someone on serverfault has seen this before :-(. uname -a 2.6.32-5-xen-amd64 #1 SMP Tue Mar 8 00:01:30 UTC 2011 x86_64 GNU/Linux Interestingly, when I read from the device I get good performance numbers: reading without encryption: $ dd if=/dev/vg0/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 68.8951 s, 95.1 MB/s reading with encryption: $ dd if=/dev/mapper/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 69.7116 s, 94.0 MB/s However, when I try to write to the device: $ dd if=/dev/zero of=./test bs=64k 8809+0 records in 8809+0 records out 577306624 bytes (577 MB) copied, 321.861 s, 1.8 MB/s Also, when I read I see CPU usage, when I write, the CPU stays at almost 0% usage. Here is output of cryptsetup luksDump: LUKS header information for /dev/vg0/secure Version: 1 Cipher name: aes Cipher mode: cbc-essiv:sha256 Hash spec: sha1 Payload offset: 2056 MK bits: 256 MK digest: dd 62 b9 a5 bf 6c ec 23 36 22 92 4c 39 f8 d6 5d c1 3a b7 37 MK salt: cc 2e b3 d9 fb e3 86 a1 bb ab eb 9d 65 df b3 dd d9 6b f4 49 de 8f 85 7d 3b 1c 90 83 5d b2 87 e2 MK iterations: 44500 UUID: a7c9af61-d9f0-4d3f-b422-dddf16250c33 Key Slot 0: ENABLED Iterations: 178282 Salt: 60 24 cb be 5c 51 9f b4 85 64 3d f8 07 22 54 d4 1a 5f 4c bc 4b 82 76 48 d8 a2 d2 6a ee 13 d7 5d Key material offset: 8 AF stripes: 4000 Key Slot 1: DISABLED Key Slot 2: DISABLED Key Slot 3: DISABLED Key Slot 4: DISABLED Key Slot 5: DISABLED Key Slot 6: DISABLED Key Slot 7: DISABLED

  Read the article

• Resource Monitor (resmon) in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

  Read the article

• VoIP setup for one external PSTN line

  - by Jcl

  I'm completely new to VoIP and the likes, and I'm trying to find information about what could be the best setup for this. I need 4 (maybe more in the future, but maximum 5 or 6) wireless extensions, connected to 1 PSTN line, and maybe 2 in the future. I've been trying to gather information about the gear needed but everything I find seems too much over-the-top (and extremely expensive). The main problem is that the physical place we are on doesn't have possibilities of having a decent internet connection, so using a external VoIP "virtual PBX" is not an option. Thing is, even if small, phone is critical to this organization. I currently have an analog DECT/GAP PBX which does what I need, however the PBX is very bad and the call quality is horrible, and that's why I want to change it. The requirements would be: 4 wireless terminals (routing cable is not an option), all of them ringing on incoming PSTN calls. Ability to do internal calls (4 separate offices) and ability to pass calls between terminals. The 4 terminals should be able to access the external PSTN line without dialing any special codes. Very important: terminals should be able to issue commands on the PSTN line to the external operator in the form *nn*nnnnnnnn# . Don't know wether this could face to be a problem, but I've had problems with analog PBX which would take any * as a PBX command and wouldn't allow terminals to send it to the external lines. Not so important, but would be nice to have: call waiting music Could anyone recommend such a setup? I need to be able to do this on a EXTREMELY LIMITED budget (that is: I don't have a limit, but all should get as much to zero as possible). I have enough spare powerful computers and a 300mbps wireless network which works just fine, so that's not to include in the budget. Don't really know if this is the best place to ask, but it's the most StackExchange-related site I've found to this subject.

  Read the article

• Google chrome not accepting any security certificates

  - by Jerry

  I've recently developed a problem with Google Chrome that's really annoying. I'm using Firefox at the moment with no problems whatsoever and it's the same with IE, so it's safe to say this problem is specific to Chrome. The problem is that it's not accepting security certificates from certain sites. I suppose the best place to start would be google itself. I can't search. The google search page will load but when I type some search term into the search box and hit 'search' I get the message: "You attempted to reach www.google.com, but the server presented an invalid certificate. You cannot proceed because the website operator has requested heightened security for this domain." No matter what the search term is, this is the result. Also when I try to log in to facebook - same message. Youtube works and many other sites that I know present security certs so I'm baffled. I've searched and there are other people who have had similar issues but I can't find a solution anywhere. The most common answer I'm picking up for this is to "check your system time" but I can safely say that it's not my system time. If anyone knows what is going on, I'd very much appreciate being informed. It's not super urgent as I can use Firefox to access those places Chrome won't, but it IS super annoying because I can usually sort out issues like this in no time.

  Read the article

• How to configure SCSI hard drives and RAID for Poweredge 2850 web server

  - by Saul

  I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

  Read the article

• How do you automatically close 3rd party applications when LiberKey is shut down?

  - by NoCatharsis

  Within LiberKey, I have added my own portable applications that are not included within the LiberKey library. When you go into the Properties menu for the app in the LiberKey UI, the Advanced tab has an option for Autoexecute. This dropdown menu seems to have no visible effect, at least on my current installation. I found that I could right click within the primary GUI and select "Add software group", add all 3rd party applications, then go to the Advanced tab within THAT Properties screen and select Autoexecute - "Always on startup". This solved the problem for starting the apps when LiberKey starts. However, now I'm having the same issue when closing out LiberKey. I have created a new 3rd party app that calls the same .exe, but sends the Parameter "/close". I then went to the Advanced tab and selected Autoexecute - "Always on shutdown". Seems pretty logical right? But the apps will not close on LiberKey shutdown. I cannot handle the app close-outs in the same way with a software group, as I did with the startup issue because the Autoexecute drop-down does not have an "Always on shutdown" option. Unfortunately, many of the Q&A forums on liberkey.com are in French and I took Spanish in high school. Otherwise I've not been able to find a workable answer. Any suggestions?

  Read the article

• RAID Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• HTML tabindex: Put some links last without complete enumeration

  - by Emanuel Berg

  I know I can use the HTML anchor attribute tabindex to set the tabindex of links, i.e., in what order they get focused when the user hits Tab (or Shift-Tab). But, I have a home page with tons of links, and to enumerate all those is a lot of work. The actual case is, I have four image links that by default gets index 1, 2, 3, and 4 (well, the behavior is equivalent, at least). But, I'd much rather have the first non-image link as number 1. Check it out here and you'll understand immediately. I tried to give the first non-image link (the link I desire to have tabindex 1) - I tried to give it tabindex 1 explicitly, hoping that it would cascade from there, but it didn't (i.e., the first image link got implicit tabindex 2). I also tried to give the image links ridiculously high tabindexes, but that didn't work: as the other links didn't have tabindexes at all, those highs were still "first". As a last resort (the solution currently employed) I gave the image links all tabindex -1. That makes for logical tabbing, but, it is suboptimal, as those image links are excluded from the tab loop - a user tabbing away will probably never realize that the images are clickable. I'd like them to be reachable with tabbing, but last, after all the ordinary links. If you wonder why I'm so determined to achieve this, it has to do with my own finger habits: I almost exclusively search for links, tab back, tab forth, etc., and very seldom using the mouse. Note: I'll accept a script to change the actual HTML for a complete enumeration, if you convince me there is no "set" way to solve this problem.

  Read the article

• Gray Progress Bar in Macbook Boot caused by Partition Fault

  - by Konstantin Bodnya

  Here's my problem: When I try to load my macbook it shows the gray progress bar. It takes a while to fill the whole progress and after it macbook just shuts down. I tried to boot from recovery partition and run Disk Utility to repair it. Disk Utility showed my "Macintosh HD" in a gray color and failed to repair it. I thought all my data was lost, but then I tried the following: So I booted into ubunto from live usb and it successfully mounted my macintosh hd hfs+ partition. Parted shows me the following partitions on my disk: Disk /dev/sda: 500GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 20.5kB 210MB 210MB fat32 EFI System Partition boot 2 210MB 499GB 499GB hfs+ Macintosh HD 3 499GB 500GB 650MB hfs+ Recovery HD Seems legit except for FAT32 for EFI System Partition. Since all my data is okay and backed up what should I do to recover the system. I don't really want to reinstall all the system though I believe there's a command to make it allright in linux. Thank you everyone!

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Geographically distributed file system with preferred locality

  - by dpb

  Hi All -- I'm building a application that needs to distribute a standard file server across a few sites over a WAN. Basically, each site needs to write a lot of misc files of varying size (some in the 100s MB range, but most small), and the application is written such that collisions aren't a problem. I'd like to have a system set up that meets the following qualifications: Each site can store files in a shared "namespace". That is, all the files would show up in the same filesystem. Each site would not send data over the WAN unless necessary. I.e., there would be local storage on each side of the WAN that would be "merged" into the same logical filesystem. Linux & Free ($$$) is a must. Basically, something like a central NFS share would meet most of the requirements, however it would not allow the locally written data to stay local. All data from remote sides of the WAN would be copied locally all the time. I have looked into Lustre, and have run some successful tests with it, however, it appears to distribute files fairly uniformly across the distributed storage. I have dug through the documentation and have not found anything that automatically will "prefer" local storage over remote storage. Even something that went with the lowest latency storage would be fine. It would work most of the time, which would meet this application's requirements. Any ideas?

  Read the article

• CentOS OpenVZ fail to boot after kernel update

  - by SkechBoy

  After upgrading to latest OpenVZ kernel CentOS server won't boot. When i try go boot the latest kernel server is stuck at this point: (note that images are taken from virtual kvm) http://i.stack.imgur.com/4lusz.jpg Then i try to start the server on some old kernels and than i get this error message: kernel panic - not syncing - attempted to kill init better shown on this image: http://i.stack.imgur.com/2SReF.jpg Here is some useful information fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2995.7 GB, 2995739688960 bytes 255 heads, 63 sectors/track, 364211 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004c4e4 Device Boot Start End Blocks Id System /dev/sda1 1 523 4199044+ 82 Linux swap / Solaris /dev/sda2 524 785 2104515 83 Linux /dev/sda3 786 261869 2097157230 83 Linux /dev/sda4 261870 364211 822062115 83 Linux /etc/fstab proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/sda1 none swap sw 0 0 /dev/sda2 /boot ext3 defaults 0 0 /dev/sda3 / ext3 defaults 0 0 /dev/sda4 /home ext3 defaults 0 0 and grub config file: title OpenVZ (2.6.18-274.18.1.el5.028stab098.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.18.1.el5.028stab098.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.18.1.el5.028stab098.1.img title OpenVZ (2.6.18-274.7.1.el5.028stab095.1) root (hd0,1) kernel /vmlinuz-2.6.18-274.7.1.el5.028stab095.1 ro root=/dev/sda3 vga=0x317 selinux=0 initrd /initrd-2.6.18-274.7.1.el5.028stab095.1.img title OpenVZ (2.6.18-194.8.1.el5.028stab070.4) root (hd0,1) kernel /vmlinuz-2.6.18-194.8.1.el5.028stab070.4 ro root=/dev/sda3 vga=0x317 initrd /initrd-2.6.18-194.8.1.el5.028stab070.4.img Any help is greatly appreciated Thanks.

  Read the article

• mod_rewrite REQUEST_FILENAME doesn't contain absolute path

  - by Paul Dixon

  I have a problem with a file test operation in a mod_rewrite RewriteCond entry which is testing whether %{REQUEST_FILENAME} exists. It seems that rather than %{REQUEST_FILENAME} being an absolute path, I'm getting a path which is rooted at the DocumentRoot instead. Configuration I have this inside a <VirtualHost> block in my apache 2.2.9 configuration: RewriteEngine on RewriteLog /tmp/rewrite.log RewriteLogLevel 5 #push virtually everything through our dispatcher script RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^/([^/]*)/?([^/]*) /dispatch.php?_c=$1&_m=$2 [qsa,L] Diagnostics attempted That rule is a common enough idiom for routing requests for non-existent files or directories through a script. Trouble is, it's firing even if a file does exist. If I remove the rule, I can request normal files just fine. But with the rule in place, these requests get directed to dispatch.php Rewrite log trace Here's what I see in the rewrite.log init rewrite engine with requested uri /test.txt applying pattern '^/([^/]*)/?([^/]*)' to uri '/test.txt' RewriteCond: input='/test.txt' pattern='!-f' => matched RewriteCond: input='/test.txt' pattern='!-d' => matched rewrite '/test.txt' -> '/dispatch.php?_c=test.txt&_m=' split uri=/dispatch.php?_c=test.txt&_m= -> uri=/dispatch.php, args=_c=test.txt&_m= local path result: /dispatch.php prefixed with document_root to /path/to/my/public_html/dispatch.php go-ahead with /path/to/my/public_html/dispatch.php [OK] So, it looks to me like the REQUEST_FILENAME is being presented as a path from the document root, rather than the file system root, which is presumably why the file test operator fails. Any pointers for resolving this gratefully received...

  Read the article

• Restore passwd for root on a server

  - by s.mihai

  Hello,       I have a DVR server with linux embeded. It has some telnet functions but i don't have the password for it (the chinese manufacturer refuses to give me the password). I did get a upgrade folder from them and found a passwd file inside.       So i assume that when i upgrade the firmware the password in that file will be used.       Now i am trying to modify the file so taht i can insert a password i already know.       The problem is that i don't know how to create the password hash from what i figured the password hash is $1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961       The file is named rom.ko and i found a command telnetd /mnt/yaffs/web/boa -c /mnt/yaffs/web & /bin/cp -f /mnt/yaffs/rom.ko /etc/shadow in a script file so i assume this is the right way.       Can you help me reconstruct a password that i know already? Tell me how or make one for me :) ?... passwd file: root:$1$1/lfbDKX$Hmd.FqzB8IZEohPesYi961:0:0:99999:7:-1:-1:33637592 bin::10897:0:99999:7::: daemon::10897:0:99999:7::: adm::10897:0:99999:7::: lp::10897:0:99999:7::: sync::10897:0:99999:7::: shutdown::10897:0:99999:7::: halt::10897:0:99999:7::: mail::10897:0:99999:7::: news::10897:0:99999:7::: uucp::10897:0:99999:7::: operator::10897:0:99999:7::: games::10897:0:99999:7::: gopher::10897:0:99999:7::: ftp::10897:0:99999:7::: nobody::10897:0:99999:7::: next::11702:0:99999:7:::

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >