Search Results

Search found 18303 results on 733 pages for 'network analyzation'.

Page 138/733 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• VirtualBox guest network lost after host disconnects

  - by webjunk

  I am running VirtualBox both on a Snow Leopard OSX host machine and on a Windows Vista host machine. Whenever my host machines lose internet connection the guest machines seem to lose internet connectivity permanently even after the host connection to the Internet is reestablished. Resetting guest networking on the guest os, disconnecting cable via host virtualbox settings, and even restarting the guest OS do not help at all. The guest no longer can access the Internet. The only solution is restarting VirtualBox itself while the host is connected to the Internet. This really gets to be a pain when the host goes into sleep mode or I disconnect my laptop at work and then reconnect at home. Guests are setup with NAT networking. It affects guest machines with both Ubuntu and Windows XP OS'es. Is this expected behavior? Does anyone know of a fix? Or am I setup incorrectly?

  Read the article

• Setting reply priority on Wifi network with QoS?

  - by Omega

  When using a Station and Access Point that support QoS over Wifi, is it possible to set the priority (= Traffic Identifier = TID = QoS channel) of the reply? For example when sending a ICMP ping request using a high priority (= QoS channel), is it possible to force the station to use that same priority (= QoS channel) when sending the reply? A related question: Is it possible to force the station into using a different QoS channel?

  Read the article

• Setting reply priority on Wifi network with QoS?

  - by Omega

  When using a Station and Access Point that support QoS over Wifi, is it possible to set the priority (= Traffic Identifier = TID = QoS channel) of the reply? For example when sending a ICMP ping request using a high priority (= QoS channel), is it possible to force the station to use that same priority (= QoS channel) when sending the reply? A related question: Is it possible to force the station into using a different QoS channel?

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• Best way to connect a desktop computer to a 3g network

  - by dbyrne

  A friend of mine is moving to a building with no Internet connectivity. Ethernet and wifi are out of the question. What is the best way for him to get his desktop connected? The most obvious solution is for him to get an unlimited 3G data plan. What is the best way for him to set this up? I am assuming he should get something like Verizon's MiFi 3G access point, but does this have an ethernet jack?

  Read the article

• Build NAS for Windows and Linux network

  - by modernzombie

  I have a spare PC and I would like to setup a NAS that is accessible from Windows and Linux. I would like to avoid using Windows as an OS and would like something like Ubuntu or FreeNAS. My only concern is I don't want to have to install special software on each client. Is there a way to use Ubuntu or FreeNAS and have Windows machines access the files with installing a client on each Windows box? UPDATE Thanks for the answers. I wish I could choose more than one. I will give FreeNAS a try and see how it goes. Thanks!

  Read the article

• All the Gear and No Idea: Suggestions for re-designing my home/office/entertainment network

  - by 5arx

  Help/ Advice/ Suggestions please: I have a load of kit that I love but which currently operate in disconnected, sometimes counter-productive way. Because I never really had a masterplan I just added these things one after another and connected them up in ad hoc ways. Since I bought my Macbook I've found I spend much less time on the MacPro that was until then my main machine. Perversely, as my job involves writing .Net software, I spend a lot of Mac time actually inside a Windows 7 VM. I stream media from the HP box to the PS3 and thus to the TV, but its not without its limitations/annoyances. We listen to each other's iTunes libraries but the music files are all over the place and it would be good to know they were all safely in one location (and fully backed up). I need to come up with a strategy that will allow me to use all the kit for work, play (recording live music, making tunes, iMovie work), pushing/streaming media to the TV and sharing files with my other half (she uses a Windows laptop and her iPod touch). Ideally I'd like to be able to work on any of the machines and have a shared homedrive that was visible to all machines so all my current files were synced up wherever i was. It would be great if I could access everything securely and quickly over the web. I'd also like to be able to set up a background backup process. The kit list thus far: Apple MacPro 8GB/3x250GB RAID0 + 1TB Apple MacBook Pro 13" 8GB/250GB - I spend a lot of my work time on a Windows 7 VM on this. Crappy Acer laptop (for children's use - iPlayer, watching movies/tv files) HP Proliant Server 4GB/80GB+160GB+300GB Sun Ultra 10 2 x 80GB (old, but in top-notch condition) PS3 160GB iPod Classic 2 x 8GB iPod Touch Observations: Part of the problem is our dual use of Windows and OS X - we can't go for a pure NT style roaming profile. Because the server is also used for hosting test/beta applications and a SQL Server db, it can't be dedicated to file serving. The two Macs really could do with sharing a roaming profile or similar. I'd love to be able to do something useful with the Ultra 10. My other half has been trying to throw it away for over five years now and regularly ask what function it serves in my study :-( I've got no shortage of 500GB external USB hard drives iMovie files are very large and ideally would be processed on a RAID system. Apple's TimeMachine isn't so great. If anyone could suggest all or part of a setup that would fulfil some of my requirements I'd be very grateful. I am willing to consider purchasing one or two more bits of kit (an Apple TV and a Squeezebox have been moted by friends) if they will help make efficiencies rather than add to the chaos and confusion. Thanks for looking.

  Read the article

• asp.net Impersonate User for network resource access

  - by lonelycoder

  code: System.Security.Principal.WindowsImpersonationContext impersonationContext; impersonationContext = ((System.Security.Principal.WindowsIdentity)User.Identity).Impersonate(); //access network resources. impersonationContext.Undo(); web.config: <authentication mode="Windows"> </authentication> <identity impersonate="true" userName="user" password="password"></identity> As clear from web.config file, the app runs in an impersonated mode. I need to impersonate temporarily on top of that to access a network resource. I do that as shown above. This works fine on server if I browse to the website on the local IE installed on the server but when I access the app from my PC or any other PC, I get a access denied. Btw, this is all within an enterprise domain environment. so IE in both cases is passing a valid authenticated token. Any ideas what is going on. thanks.

  Read the article

• New router, old network, but devices won't talk to each other

  - by JDedman

  I plugged the new router in and get internet on both the computer and the Xbox 360. The Xbox 360 only recognizes the computer when I turn the Smart Wall off in my Norton antivirus, and only when the computer is hardwired. How do I make it so that Norton will allow the computer and Xbox to talk? Reset the MAC address? I have no idea how to do this, and I'm starting to think it's the answer to my problem. Any help would be greatly appreciated.

  Read the article

• network issue ubuntu 8.04 in vmware esx

  - by hoberion

  ok, this is really pissing me off I have one ubuntu 8.04 instance running on vmware (esx) which decided after a reboot to stop resolving dns requests, I also cant connect to it using ssh although I can ping the server and its really that server (when I shutdown the server the ping also stops) stuff I tried: - reboot again :) - nslookup - serverip - setting networking to dhcp - offering some cute kittens to lucifer - removing the virtual nic and adding another (to get a different mac) - migrating the instance to another esx host - drinking 20 cups of espresso - stopped all services - running dnsmasq on another server and connecting to that dns - tcpdumping - disabling ip6 symptoms: cant resolve anything nslookup just says "no servers found..." although I can ping the servers traceroute to gateway doesnt work (even with traceroute -4 -n gatewayip) collegues laughing at me any thoughts

  Read the article

• Home network with Windows 7 as router

  - by Michael

  Background: I have tried to use routers, but so far all of them can't handle the bandwidth, number of connections eventually limited by the hardware resources, so overall the home routers are decreasing the internet speed. I went through DD-WRT and stuff like that. Question: What I want is to use my Windows7 PC as router. It has 2 LAN cards. I'm going to connect to this router another desktop 2 pcs and notebook through wireless router. The main question is what is the most efficient way to turn this Windows7 box(and I need Windows for native NTFS support) into router with NAT/Routing/Firewall functionality? Is there any routing software recommended for this purpose or I should just use windows native "Internet Sharing"? I'm going to run SIP phones in the LAN, so I need friendly NAT(Full cone perhaps). Also I'm going to have FTP server on that Windows7 "server" PC. As firewall I'm thinking about Comodo. Need to drop all incoming, unless explicitly allowed.

  Read the article

• NTPD seems to delete all network interfaces

  - by Aurelin

  We have a couple of virtual interfaces configured on eth0 on a CentOS, and every now and then, they went down seemingly out of the blue. Now after going through the log files, I found out that apparently ntpd deletes all eth0 interfaces, and that dhclient automatically brings eth0 back up. The virtual interfaces, however, stay down which causes several of our websites to be inaccessible. Can someone explain to me why ntpd deletes interfaces? Can / should that be turned off, or can / should I configure dhclient to bring the virtual interfaces back up automatically, too? EDIT// The log files that I should've posted : Nov 12 13:10:28 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x6a825e97) Nov 12 13:10:42 raptor dhclient[20048]: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPOFFER from 96.126.108.78 Nov 12 13:10:42 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPACK from 96.126.108.78 (xid=0x24554092) Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #31 eth0, 50.116.50.97#123, interface stats: received=3255, sent=3256, dropped=0, active_time=1559394 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #32 eth0:0, 50.116.53.56#123, interface stats: received=3, sent=0, dropped=0, active_time=1559391 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #33 eth0:1, 66.175.211.192#123, interface stats: received=2, sent=0, dropped=0, active_time=1559389 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #34 eth0:2, 50.116.53.95#123, interface stats: received=3, sent=0, dropped=0, active_time=1559387 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #35 eth0:3, 97.107.132.32#123, interface stats: received=2, sent=0, dropped=0, active_time=1559385 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #36 eth0:4, 50.116.56.201#123, interface stats: received=2, sent=0, dropped=0, active_time=1559383 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #37 eth0:5, 66.175.212.121#123, interface stats: received=2, sent=0, dropped=0, active_time=1559381 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #38 eth0:6, 66.175.215.137#123, interface stats: received=2, sent=0, dropped=0, active_time=1559379 secs Nov 12 13:10:44 raptor NET[1573]: /sbin/dhclient-script : updated /etc/resolv.conf Nov 12 13:10:44 raptor dhclient[20048]: bound to 50.116.50.97 -- renewal in 32692 seconds. Nov 12 13:10:45 raptor ntpd[2109]: Listening on interface #39 eth0, 50.116.50.97#123 Enabled The eth0 config : DEVICE="eth0" ONBOOT="yes" BOOTPROTO="dhcp" IPV6INIT="no" IPADDR=50.116.50.97 NETMASK=255.255.255.0 GATEWAY=50.116.50.1 And the virtual interfaces (I posted the first one only, they look the same for the most part) : # Configuration for eth0:0 DEVICE=eth0:0 BOOTPROTO=none # This line ensures that the interface will be brought up during boot. ONBOOT=yes # eth0:0 IPADDR=50.116.53.56 NETMASK=255.255.255.0

  Read the article

• JBoss 5.1 binds to host address while run in vserver with -b <guest address>

  - by bart cane

  Hello, while starting JBoss 5.1.0.GA in virtual server machine on Debian (linux-VServer technology) I get the following error: ERROR [org.jboss.kernel.plugins.dependency.AbstractKernelController] (main) Error installing to Start: name=jboss.remoting:protocol=rmi,service=JMXConnectorServer state=Create mode=Manual requiredState=Installed java.io.IOException: Cannot bind to URL [rmi://10.1.2.11:1090/jmxconnector]: javax.naming.NoPermissionException [Root exception is java.rmi.ServerException: RemoteException occurred in server thread; nested exception is: java.rmi.AccessException: Registry.Registry.bind disallowed; origin /AA.BB.CC.DD is non-local host] where AA.BB.CC.DD is host machine name, 10.1.2.11 is vserver guest with JBoss and JBoss is started with -b 10.1.2.11 (I also tried -Djboss.bind.address=10.1.2.11 - the same result). 10.1.2.11 is bound to dummy2 interface on host (serving 10.1.2.1 network). The root exception is strange - why JBoss wants to bind to host address AA.BB.CC.DD? There were no problems with 4.2.3.GA on the same machine, also started with -b 10.1.2.11. It starts correctly when no params present - binds to localhost and everything is ok, but it MUST be bound to 10.1.2.11 to be visible by Apache on another vserver guest, acting as proxy. I thought that it can be fixed by setting net.ipv4.conf.all.promote_secondaries=1 via sysctl (was 0) but it didn't help much. Has anyone had such problem? Regards, bart

  Read the article

• Logging network activity of LAMP server using BASH

  - by Yarin

  I've got a Fedora LAMP server on Amazon EC2 functioning as a HTTP pseudo-proxy (Sorry, don't know the terminology- It's not a true proxy where requests are relayed through apache, rather client requests are being translated by a PHP script, which then sends a new request.) I'd like to be able to fully log the HTTP cycle CLIENT - PROXY PROXY - SERVICE SERVICE - PROXY PROXY - CLIENT I'm hoping to do this using BASH tools- thinking netcat? Looking for advice and examples. Thanks!

  Read the article

• Gauge network traffic for each Citrix session

  - by molecule

  Hi all, We are currently reviewing the bandwidth of our WAN links. How much bandwidth does a "typical" Citrix session utilize over a WAN link? JFYI - we are using Citrix Program Neighborhood V10 and each session is configured to use 256 colors. I have set up PRTG and it appears that for a server hosting 4 users, the traffic is approximately 100k to 300k per session. Is that about right? If you had to set a benchmark on a per-user basis, how much bandwidth would you assign to each user? Thanks in advance.

  Read the article

• Network corruption - corrupt downloads, corrupt streams, etc.

  - by rfrankel

  I've been having some problems with my home LAN. Downloaded executables won't run, my remote desktop sessions keep getting interrupted due to encryption errors, flash video streams show visible corruption (both Hulu and YouTube), and I've had a couple downloads for which the md5 hashes don't match. The problem has even occurred with a couple images embedded in webpages, though that's rare enough (presumably because images are relatively smaller files). I've had this problem across two Windows machines and a Mac, so it's neither machine-specific nor at the app or OS level. Comcast claims it's nothing to do with them, and my Linksys/Cisco RV016 router is out of warranty, so I have no access to official support. When I log into my router, it shows no error packets or dropped packets received. I plugged a laptop directly into the router and was able to download a 5.5 MB file and verify its MD5 hash, which is not proof that the problem is downstream of the router, but makes it seem quite likely, since I failed to download the same file several times from two desktops (one Mac, one Windows). Could this be a wiring problem? If so, is there any way clever/elegant to determine which wiring is faulty with just software? If I can avoid tracing all the wires throughout my entire house it would make my life quite a bit easier.

  Read the article

• Requiring 802.1x login before allowing access to network resources

  - by Calvin Froedge

  I have a ZyXel GS2200-24 managed switch, and a free-radius server running on Ubuntu 11.10. Radius is configured and when I log into the switch the authentication goes through Radius. Now, I'm trying to ensure that access to web resources (as an example, I set up a web server on the ip 192.168.1.2) requires first authenticating with radius, before the switch will allow the connection. Am I correct that this should be handled at the switch level? What are these rules usually called / how are they usually defined?

  Read the article

• Forwarding MySQL connection with iptables and differents network interfaces

  - by Emilio Nicolás

  I have a PC with Ubuntu as a router. It has a 3G connection with a public IP to the Internet, and there is a private wireless subnet. So it has two active interfaces: ppp0: public IP (WAN) wlan0: private IP (LAN) With iptables I wannt to forward every MySQL connection (port 3306) to a local machine (10.42.43.10) of the subnet. I type these iptables commands: iptables -A PREROUTING -t nat -i ppp0 -p tcp --dport 3306 -j DNAT --to 10.42.43.10:3306 iptables -A FORWARD -p tcp -i ppp0 -o wlan0 -d 10.42.43.10 --dport 3306 -j ACCEPT But it doesn't work. telnet publicip 3306 fails :-( Any help will be appreciated. Thanks!

  Read the article

• Active Directory Domain Services - Network Name Cannot be Found

  - by Arief

  I have really weird problem that I could not explain. I am trying to redirect all users home folder to the new server. I have copied all the files including the permissions to the new server. All I need to do is to update the user profile for home folder by changing the server name. However, I got this message when I enter the new server name: My server that serving as AD can resolve the name by ping and nslookup of the server name. The only thing that I don't understand why the MMC cannot resolve the name. I did change with the IP Address and I still get the same error message. Thank you so much for your help. UPDATE: I know what seems to be a problem, but I don't know how to fix it. The new server that will serve all Home folder is actually sitting in the cloud with different IP Address as the Domain Controller. The Domain Controller is sitting locally in the office with 10.0.0.0/24 IP Addresses. The new server that is sitting in on Data Centre is on 172.10.10.10/24 IP Addresses. The static route has been set up on both end, and the DNS as well. I believe this is the issue. Does anyone how to overcome this situation? Thank you.

  Read the article

• Setting up dnsmasq for a local network

  - by WishCow

  Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

  Read the article

• Setting up dnsmasq for a local network

  - by WishCow

  Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

  Read the article

• Internet Explorer / Windows 7 does not want to show HTML file from local network drive

  - by Jaanus

  Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

  Read the article

• Daisy-chaining network switches with multiple cables

  - by user72153

  This might just be the dumbest question you'll ever read, but I digress. Say I have two 100Mbps Ethernet switches with 2 computers on each, connected together by a single cable. This way, the two PCs on each switch share the 100Mbps bandwidth with the others. If I added another cable between the 2 switches, would there be 200Mbps throughput available between the switches? Or am I completely off my rocker? Thanks for the help.

  Read the article

• Apache HTTP Server - Other local network pc can't access web application [closed]

  - by Manellen

  I have problem while accessing my web application through other pc via LAN. Here is the scenario: I have 3 computers directly connected to LAN and one computer has installed Apache HTTP Server also has a web application. 2 Other computers try to access wep application to the installed Apache HTTP Server computer and that 2 computers can't access the web application. That 2 computer displaying Does anyone know how to fix it? (fix how to make that 2 computer could access the web application through LAN) Thanks in advance.

  Read the article

• Unable to resolve hostname on a proxy network

  - by ali

  I can browse sites using firefox configured with proxy 172.1.6.0.6:3128 resolv.conf domain pudhcp.ac.in search pudhcp.ac.in nameserver 172.16.0.7 I checked with Windows and I found the same DNS server settings 127.0.0.1 bt 127.0.1.1 bt Above is the hosts file I modified the top line from localhost to bt still not working bt is the hostname Still I can't ping to google.com - it is showing unable to resolv hostname I tried all solutions,I guess proxy is used even for DNS resolution root@bt:~# dhclient There is already a pid file /var/run/dhclient.pid with pid 7157 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/eth1/5c:ac:4c:b1:0c:7c Sending on LPF/eth1/5c:ac:4c:b1:0c:7c Listening on LPF/eth0/60:eb:69:18:4d:3d Sending on LPF/eth0/60:eb:69:18:4d:3d Sending on Socket/fallback DHCPREQUEST of 172.16.6.87 on eth0 to 255.255.255.255 port 67 DHCPACK of 172.16.6.87 from 172.16.6.1 bound to 172.16.6.87 -- renewal in 79432 seconds.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >