Search Results

Search found 172701 results on 6909 pages for 'not provided'.

Page 138/6909 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

  • Cisco adaptive security appliance is dropping packets where SYN flag is not set

    - by Brett Ryan
    We have an apache instance sitting inside our DMZ which is configured to proxy requests to an internal NATed tomcat instance inside our network. It works fine, but then all of a sudden requests from apache to the tomcat instance stop getting through with the following in the apache logs: [error] (70007)The timeout specified has expired: ajp_ilink_receive() can't receive header Investigating into the Cisco log viewer reveals the following: Error Message %ASA-6-106015: Deny TCP (no connection) from IP_address/port to IP_address/port flags tcp_flags on interface interface_name. Explanation The adaptive security appliance discarded a TCP packet that has no associated connection in the adaptive security appliance connection table. The adaptive security appliance looks for a SYN flag in the packet, which indicates a request to establish a new connection. If the SYN flag is not set, and there is not an existing connection, the adaptive security appliance discards the packet. Recommended Action None required unless the adaptive security appliance receives a large volume of these invalid TCP packets. If this is the case, trace the packets to the source and determine the reason these packets were sent. All are machines are virtualised using VMware, and by default machines have been using the Intel E1000 emulated NIC. Our network administrator has changed this to a VMXNET3 driver in an attempt to correct the problem, we just have to wait and see if the problem persists as it's an intermittent problem. Is there something else that could be causing this problem? This isn't the first service where we have had similar issues. Our apache host is running Ubuntu 11.10 with a kernel version of 3.0.0-17-server. We have also had this issue on RHEL5 (5.8) running kernel 2.6.18-308.16.1.el5, this machine also has the E1000 NIC. NOTE: I am not a network administrator and am a software architect and analyst programmer responsible for these systems.

    Read the article

  • Host name or Domain not found

    - by hitesh-4259
    Hi I have installed amavis + postfix + spamassassin on centOS 5.4. The "/etc/hosts" file contains: 127.0.0.1 localhost.localdomain localhost ::1 localhost6.localdomain6 localhost6 67.215.65.132 mail.sufalamtech.local mail When I am sending mail then, the following error is occured: Apr 8 06:20:53 mail sendmail[3229]: o380oqu7003229: from=root, size=62, class=0, nrcpts=1, msgid=<[email protected], relay=root@localhost Apr 8 06:20:53 mail postfix/smtpd[3230]: connect from mail.sufalamtech.local[127.0.0.1] Apr 8 06:20:53 mail sendmail[3229]: STARTTLS=client, relay=[127.0.0.1], version=TLSv1/SSLv3, verify=FAIL, cipher=DHE-RSA-AES256-SHA, bits=256/256 Apr 8 06:20:54 mail postfix/smtpd[3230]: 5A53C1A5989: client=mail.sufalamtech.local[127.0.0.1], [email protected] Apr 8 06:20:54 mail postfix/cleanup[3238]: 5A53C1A5989: message-id=<[email protected] Apr 8 06:20:54 mail sendmail[3229]: o380oqu7003229: [email protected], ctladdr=root (0/0), delay=00:00:02, xdelay=00:00:01, mailer=relay, pri=30062, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (Ok: queued as 5A53C1A5989) Apr 8 06:20:54 mail postfix/qmgr[3107]: 5A53C1A5989: from=, size=587, nrcpt=1 (queue active) Apr 8 06:20:54 mail postfix/smtpd[3230]: disconnect from mail.sufalamtech.local[127.0.0.1] Apr 8 06:20:54 mail postfix/smtp[3240]: 5A53C1A5989: to=, relay=none, delay=0.63, delays=0.17/0.1/0.36/0, dsn=5.4.4, status=bounced (Host or domain name not found. Name service error for name=mail.sufalamtech.local type=A: Host not found) Apr 8 06:20:54 mail postfix/cleanup[3238]: E73C51A5987: message-id=<[email protected] Apr 8 06:20:54 mail postfix/qmgr[3107]: E73C51A5987: from=<, size=2594, nrcpt=1 (queue active) Apr 8 06:20:54 mail postfix/bounce[3241]: 5A53C1A5989: sender non-delivery notification: E73C51A5987 Apr 8 06:20:54 mail postfix/qmgr[3107]: 5A53C1A5989: removed Apr 8 06:20:55 mail postfix/local[3242]: E73C51A5987: to=, relay=local, delay=0.15, delays=0.02/0.1/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) Apr 8 06:20:55 mail postfix/local[3242]: warning: host not found: localhost Apr 8 06:20:55 mail postfix/qmgr[3107]: E73C51A5987: removed Apr 8 06:21:04 mail postfix/qmgr[3107]: warning: connect to transport amavis: No such file or directory Apr 8 06:22:04 mail postfix/qmgr[3107]: warning: connect to transport amavis: No such file or directory

    Read the article

  • Task Scheduler not able to execute .vbs scripts successfully

    - by Django Reinhardt
    Apologies if this has a really obvious answer! We have several daily tasks we run via a .vbs script on our server (through the Task Scheduler), and for months it has been fine, but recently we've hit a problem. The .vbs scripts stopped successfully executing (always timing out)... but could still be executed manually with no problems(!). Not knowing any good reason why the Task Scheduler should start having problems, we thought we'd try a little "creative thinking", and run the .vbs another way: Via a .bat file executed by the Task Scheduler. Again we hit weird issues, but with a little more debugging information, this time around. The .bat file run by Task Scheduler is nothing more than... CScript "C:\location\script.vbs" > Log.txt But after an attempt to run it, the Task Scheduler fails with the following error: 0x1: An incorrect function was called or an unknown function was called. The Log.txt (as output from the .bat file above) says: CScript Error: Initialization of the Windows Script Host failed. (Not enough storage is available to process this command. ) But get this: The .bat file executes perfectly (vbs script and all) if it's executed with a double click! There's only a problem when it's run by Task Scheduler. What the hell? We're running Windows Server 2008 R2 (x64) and yes, the Task Sheduler's results are the same whether the user is logged in or not. Also, the user that can run the scripts successfully manually, is also the same user that runs the scripts in Task Scheduler. Thanks for any help for this weird problem!

    Read the article

  • Video and LAN Cards are not recognized on Intel DG41RQ MB

    - by artyom
    Hello, My 32 bit Debian Etch with Etch-n-Half kernel 2.6.24 and Etch-n-half video driver xserver-xorg-video-intel 2.2.1-1~etchnhalf2 does not recognize my on-board LAN and Video. I can work only with VESA display. And additional PCI LAN card (that I wanted to use for Cross-X-Cabel). output of lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 4 Series Chipset PCI Express Root Port (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10 According to MB Spec: Video: Intel G41 Express Chipset Graphics and Memory Controller Hub Graphics (GMCH) LAN: Realtek 8111D Gigabit Ethernet Controller LAN Support When I run dpkg-reconfigure xserver-xorg is suggest i810 driver but X does not start, it does not start with intel driver as well; only vesa. LAN I even can't find in lspci... the last Realtek card is external one 100MB card. Where to start from?

    Read the article

  • bonding module parameters are not shown in /sys/module/bonding/parameters/

    - by c4f4t0r
    I have a server with Suse 11 sp1 kernel 2.6.32.54-0.3-default, with modinfo bonding i see all parameters, but under /sys/module/bonding/parameters/ not modinfo bonding | grep ^parm parm: max_bonds:Max number of bonded devices (int) parm: num_grat_arp:Number of gratuitous ARP packets to send on failover event (int) parm: num_unsol_na:Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event (int) parm: miimon:Link check interval in milliseconds (int) parm: updelay:Delay before considering link up, in milliseconds (int) parm: downdelay:Delay before considering link down, in milliseconds (int) parm: use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default) (int) parm: mode:Mode of operation : 0 for balance-rr, 1 for active-backup, 2 for balance-xor, 3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, 6 for balance-alb (charp) parm: primary:Primary network device to use (charp) parm: lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast) (charp) parm: ad_select:803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2) (charp) parm: xmit_hash_policy:XOR hashing method: 0 for layer 2 (default), 1 for layer 3+4 (charp) parm: arp_interval:arp interval in milliseconds (int) parm: arp_ip_target:arp targets in n.n.n.n form (array of charp) parm: arp_validate:validate src/dst of ARP probes: none (default), active, backup or all (charp) parm: fail_over_mac:For active-backup, do not set all slaves to the same MAC. none (default), active or follow (charp) in /sys/module/bonding/parameters ls -l /sys/module/bonding/parameters/ total 0 -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_grat_arp -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_unsol_na I found some of this parameters under /sys/class/net/bond0/bonding/, but when i try to change one i got the following error echo layer2+3 > /sys/class/net/bond0/bonding/xmit_hash_policy -bash: echo: write error: Operation not permitted

    Read the article

  • Iomega eGo Encrypt Plus Encrypted Partition not mounting properly says "local disk"

    - by mosiac
    I'm working with an Iomega eGo 500gb Encrypt Plus portable drive. When I first set it up and installed the software and set a user password everything worked fine. The partition labeled "IomegaHDD" mounted properly and I could access the free space. Then I changed the ADMIN password which required me to lockout the device, wait 60 seconds, and then login to the Admin section and change the password, lockout the device again, wait 60 seconds, and then log back in with my user password. When I did that it of course unmounted the IomegaHDD partition to secure it, when it remounts it, it only shows up as "local disk" now and will not remount properly. I had not removed the cable while doing any of this. I have since tried unplugging and plugging back in to login to the drove but that has not worked. I'm wondering if I should remove every instance of "generic usb hub" from device manager and wait for it to re-add itself, or move it to a new set of USB ports temporarily to seee if that helps. Any ideas?

    Read the article

  • vhost.conf file in PLESK not working as intended

    - by Saif Bechan
    I have configured a vhost file for my domain but it does not seem to work. These are the steps I took, please correct me if I am wrong. First I made a file called vhost.conf in: /var/www/vhosts/*domain*/conf/vhost.conf The content of the vhost file looks like this: <Directory /var/www/vhosts/*domain*/httpdocs> php_admin_flag engine on php_admin_flag display_errors on </Directory> Now in my /etc/php.ini i set display_errors=Off After everything i rebuild with: /usr/local/psa/admin/sbin/websrvmng -a But I don't see the any errors in my page. When i turn on the display_errors in /etc/php.ini only then can I see the errors. I know for a fact that the vhost file is read, because when i type nonsense values i get an error when restarting apache saying there are errors in the vhost file. Anyone know what the problem can be. Should there be special settings in either the php.ini file or the httpd.conf file. The httpd.conf i edit is in /etc/httpd/conf/httpd.conf. Is this the file that PLESK uses or is there another, because the values i see there do not really reflect the http folders of my domain. The httpd file looks like this now. # The document root DocumentRoot "/var/www/html" # i guess this is the base directory <Directory /> Order Deny,Allow Deny from all Options None AllowOverride None </Directory> # And i guess here are all my domains located, but there aren't any here <Directory "/var/www/html"> Options None AllowOverride None Order allow,deny Allow from all </Directory> Only this directory /var/www/html is not used by me, I use the directory /var/www/vhosts. The only folder found in /var/www/html is a folder called awstats. Does plesk use other files, and where are they located. I hope this all makes sense to anyone, and i hope i can find a solution

    Read the article

  • qemu-img: Could not open $FILE

    - by HTTP500
    I received a single-file VMDK from a vendor that has a virtual appliance for a particular product I'm interested in evaluating. We run a KVM solution (Proxmox) so I tried converting the file but on that system qemu-img blows up. (I was able to convert (multipart) VMDK files from bitnami without error.) So I figured I'll just yum install qemu-img on a RHEL 6.3 VM and do it there. But despite the fact that I can file the file just fine when I run qemu-img on it I get this error that it can't open the file: [root@host dir]# file 1.vmdk 1.vmdk: VMware4 disk image [root@host dir]# qemu-img info 1.vmdk qemu-img: Could not open 'vmdk' I've seen some other people post on the interwebs that they've had this problem but none of them seem to have a resolution. Does anyone have any ideas? I have checked the MD5SUM already. EDIT1: [root@host dir]# qemu-img info -f vmdk 1.vmdk qemu-img: Could not open '1.vmdk' EDIT2: Ran strace per suggestion. Not sure what to look for... Here is a possible: ioctl(3, CDROM_DRIVE_STATUS, 0x7fffffff) = -1 ENOTTY (Inappropriate ioctl for device)

    Read the article

  • SNMPD running but not listening for connections at random

    - by Lukasz
    OS: CentOS release 5.7 (Final) Net-SNMP: net-snmp-5.3.2.2-14.el5_7.1 (from RPM) Periodically my NMS notifies me that SNMP has gone down on this machine. The service is restored in between 10 to 30 minutes. My NMS also pings and check SSH and those services are not affected during the SNMP outage. SNMPD log file shows that it is working and apparently receiving packets (either from local agents from 127.0.0.1 or from my NMS at 172.16.37.37) however attempting to snmpwalk locally or from the NMS system fails with a timeout. I have 7 of these servers running mixture of CentOS 5.7 and RHEL 5.7 with this specific version of Net-SNMP installed from RPM - none of them have this issue except this one. 5 of the machines (including the NMS system and this problem server) are in the same rack connected using one switch. Restarting SNMPD does not fix the issue - it clears up by itself eventually. Any suggestions where I can begin diagnosing the issue? It's a closed subnet so IPTables is not used. SNMPD config below: # Following entries were added by HP Insight Management Agents at # Tue May 15 10:58:17 CLT 2012 dlmod cmaX /usr/lib64/libcmaX64.so rwcommunity public 127.0.0.1 rocommunity public 127.0.0.1 rwcommunity 3adRabRu 172.16.37.37 rocommunity 3adRabRu 172.16.37.37 rwcommunity 3adRabRu 172.16.37.36 rocommunity 3adRabRu 172.16.37.36 trapcommunity callmetraps trapsink 172.16.37.37 callmetraps trapsink 172.16.37.36 callmetraps syscontact Lukasz Piwowarek syslocation Santiago, Chile # ---------------------- END -------------------- agentAddress udp:161 com2sec rwlocal default public com2sec rolocal default public com2sec subnet default 3adRabRu group rwv2c v2c rwlocal group rov2c v2c rolocal group rov2c v2c subnet view all included .1 access rwv2c "" any noauth exact all all none access rov2c "" any noauth exact all none none

    Read the article

  • SQL Server Management Studio not scripting all objects

    - by Ian Boyd
    i've been attempting to script a database using SQL Server 2005 Management Studio. i cannot get it to script some objects. It scripts others, but skips some. i can provide detailed screen shots the options being selected including all tables the folder where the script files will go the folder being empty before scripting the scripting process saying Sucess when scripting a table the destination folder no longer empty, with a hundred or so script files the script of some tables not being in the folder. And earlier SSMS would not script some views. Is this a known thing that the the Generate Scripts task does not generate scripts? Update Known issue on Microsoft Connect, but Microsoft couldn't repro the steps, so they closed closed the ticket. Fails on SQL Server 2005, also fails on SQL Server 2008. Update Two Some basic questions: 1.What version of SQL Server? Microsoft SQL Server 2000 - 8.00.194 (Intel X86) Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Microsoft SQL Server 2008 - 10.0.2531.0 (Intel X86) Microsoft SQL Server 2005 Management Studio: 9.00.4035.00 Microsoft SQL Server 2008 Management Studio: 10.0.1600.22 2.What O/S are you running on? Windows Server 2000 Windows Server 2003 Windows Server 2008 3.How are you logging in to SQL server? sa/password Trusted authentication 4.Have you verified your account has full access to all objects? Yes, i have access to all objects. 5.Can you use the objects that fail to script? (eg: select top(10) * from nonScriptingTable) Yes, all objects work fine. SQL Server Enterprise Manager can script the objects fine. Update Three They fail no matter what version of SQL Server you script against. It wasn't a problem in Enterprise Manager: Client Tools SQL Server 2000 SQL Server 2005 SQL Server 2008 ============ =============== =============== =============== 2000 Yes n/a n/a 2005 No No No 2008 No No No Update Four No errors found in the database using: DBCC CHECKDB go DBCC CHECKCONSTRAINTS go DBCC CHECKFILEGROUP go DBCC CHECKIDENT go DBCC CHECKCATALOG go EXECUTE sp_msforeachtable 'DBCC CHECKTABLE (''?'')' Honk if you hate SSMS.

    Read the article

  • Can not join additional domain controllers

    - by Hosm
    Hi all, I had a dead PDC and another not so synced domain controller for my domain. using comments here link now the so called secondary domain controller has seized domain controls and I can verify it from dsa.msc that it is a domain controller. I set up another domain controller (win2003SRV) and about to promote an AD on it as a domain controller for my domain. When I try to join the new domain controller to the domain I face DNS problem. here is some more detail DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain DOMNAME.A.B: The query was for the SRV record for _ldap._tcp.dc._msdcs.DOMNAME.A.B The following domain controllers were identified by the query: update.DOMNAME.A.B Common causes of this error include: - Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. For information about correcting this problem, click Help. it is worth noting that update.DOMNAME.A.B is the current domain controller to which I'd like to add another controller named PDC.DOMNAME.A.B Ip address of update.DOMNAME.A.B is 192.168.200.1 and for pdc.DOMNAME.A.B is 192.168.200.100 querying DNS on both machine return correct results. Any idea?

    Read the article

  • Website does not resolve in browser but traceroute is successful

    - by Colum
    I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

    Read the article

  • Website does not resolve in browser but traceroute is successful

    - by Colum
    I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

    Read the article

  • Apache2: not defined domains directing to the same virtual host

    - by rafaame
    I have Apache2 configured in a debian box with virtual hosts. I have several domains pointing to the box's IP address. The domains whose virtual hosts are configured works perfectly. But if I type in the browser a domain that is pointing to the box but whose the virtual host is not configured, I get to a random virtual host of another domain in the box. Not a random, but one of the virtual hosts (always the same) but I dunno why it is it. The correct would be that the domains that are not configured as virtual hosts return a hostname error or something, right? Does someone know how to fix the problem? One of my virtual hosts config file: <VirtualHost *:80> ServerAdmin [email protected] ServerName dl.domain.com DocumentRoot /var/www/dl.domain.com/public_html/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/dl.domain.com/public_html/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My apache2.conf http://www.speedyshare.com/files/29107024/apache2.conf Thanks for the help

    Read the article

  • award phoenix bios not recognizing my sata hdd.

    - by josh
    What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

    Read the article

  • MySQL table does not exist

    - by Phanindra
    I am getting following error in err file. 110803 6:51:26 InnoDB: Error: table `ims`.`temp_discoveryjobdetails` already exists in InnoDB internal InnoDB: data dictionary. Have you deleted the .frm file InnoDB: and not used DROP TABLE? Have you used DROP DATABASE InnoDB: for InnoDB tables in MySQL version <= 3.23.43? InnoDB: See the Restrictions section of the InnoDB manual. InnoDB: You can drop the orphaned table inside InnoDB by InnoDB: creating an InnoDB table with the same name in another InnoDB: database and copying the .frm file to the current database. InnoDB: Then MySQL thinks the table exists, and DROP TABLE will InnoDB: succeed. InnoDB: You can look for further help from InnoDB: http://dev.mysql.com/doc/refman/5.1/en/innodb-troubleshooting.html And when I do the same, like copying the frm file from other database to here and drop the table, i am getting following error, InnoDB: Error: trying to load index PRIMARY for table ims/temp_discoveryjobdetails InnoDB: but the index tree has been freed! 110803 6:50:26 InnoDB: Error: table `ims`.`temp_discoveryjobdetails` does not exist in the InnoDB internal InnoDB: data dictionary though MySQL is trying to drop it. InnoDB: Have you copied the .frm file of the table to the InnoDB: MySQL database directory from another database? InnoDB: You can look for further help from InnoDB: http://dev.mysql.com/doc/refman/5.1/en/innodb-troubleshooting.html Please any one help me out of this. Also can any one tell me why this error is coming. EDIT: The issue is occurring only when disk size is full and when we use Truncate table. Also this is occurring only in 5.1 version but not in 5.0 version.

    Read the article

  • Installing ubuntu 12.04, installs but does not boot after it asks me to remove the CD

    - by Randnum
    I'm Trying to install Ubuntu 12.04 on my computer. It had an old copy of Windows 7 on it I tried to reformat the hard drive for a fresh install of Ubuntu but I think I messed up the partitions in some way that prevents it from fully loading. I'm able to complete the install fine and use guided partitioning so it should be happy but when it gets about 90% through at the part that ejects the cd and restarts the system it fails. After ejecting the CD and restarting it just loads up the bios lenovo splash screen then purple then black. I can hear a sound from my speakers like some notification sound but there is no text on my screen. I've since gone back in under Rescue System to try and reconfigure the partitions hoping that it will fix it and i've tried several combinations. Currently it's SCST1 (0,0,0) (sda) - 500.1 GB ATA WDC WD5000AAkKX-0 #1 100.0 MB K biosgrub #2 494.1 GB B K ext4 / #3 5.9 GB F swap swap 8.2 kb FREE SPACE I'm not sure if I need to set the ext4 to contain the boot flag but if I don't include at least one partition with the boot flag enabled it complains saying that "The partition table format in use on your disks normally requires you to create a separate partition for boot loader code. This partitionshould be marked for use as an "EFI boot Partition" and should be at least 35 MB in size. Note that this is not hte same as a partition mounted on /boot" Like I said it seems to have installed all of the actual data from the CD it's just not properly booting for some reason

    Read the article

  • NGINX SSI Not working

    - by Mike Kelly
    I'm having trouble getting SSI to work on NGINX. You can see the problem if you hit http://www.bakerycamp.com/test.shtml. Here is the contents of that file: <!--# echo hi --> If you hit this in a browser, you see the SSI directive in the content - so apparently NGINX is not interpreting the SSI directive. My NGINX config file looks like this: server { listen 80; server_name bakerycamp.com www.bakerycamp.com; access_log /var/log/nginx/bakerycamp.access.log; index index.html; root /home/bakerycamp.com; location / { ssi on; } # Deny access to all hidden files and folders location ~ /\. { access_log off; log_not_found off; deny all; } } I did not build NGINX from sources but installed it using apt-get. I assume it has the SSI module (since that is default) but perhaps not? Should I just bite the bullet and rebuild from sources? Is there anyway to tell if the installed NGINX supports SSI and my config is just wrong?

    Read the article

  • Internet Explorer / Windows 7 does not want to show HTML file from local network drive

    - by Jaanus
    Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

    Read the article

  • Video card not detected on Lenovo T410 in Linux

    - by wich
    I have a T410 with an nVidia NVS 3100M, this is not a hybrid system, there is no Optimus. (No option in the BIOS for Optimus, lspci in linux as well as the Windows device manager only show the nVidia) Using lspci I see the GPU as a present device, however, I can not, for the life of me, get any video driver to work that will let me start an X session, every time X craps out with the error (EE) No devices detected. I have tried the nVidia binary blob, (with nvidia-config, made sure no nvidia support in the kernel), I have tried nouveau, I have tried nv, I have even tried generic vesa, nothing will work. When I compare the dmesg that I get when loading the nvidia kernel module, I see that it is missing some lines compared with another system that also has an nvidia card, specifically the line mentioning the GPU name (3100M) is not there. I have checked every option in the BIOS, there is nothing to control except for the BIOS video output port, which is set to the LCD panel. I have no idea anymore what the problem may be, or even how I can diagnose this problem further. Any help will be appreciated.

    Read the article

  • DisableCrossAccountCopy not working on some Outlook installs, working on others, both going against Exchange

    - by MikeBaz
    As part of a mail migration project from one Exchange organization to another, we need to be able to prevent users from moving/copying messages between their accounts in each organization. (Yes, users will think this is evil; no, it's not my decision; yes, users will hate us.) Luckily, we thought, Outlook 2010 provides the DisableCrossAccountCopy registry value/policy (cf. http://technet.microsoft.com/en-us/library/ff800883.aspx). (Because you can't do multiple Exchange organizations in a single profile before Outlook 2010, this only matters on Outlook 2010. Yes, I'm ignoring for the sake of this question copy/move to/from the filesystem.) In our test lab, in a test forest with a test Exchange organization, with a second Exchange account added to the profile in either of the "real" Exchange organizations, with the value set to "*", everything works as expected. On a workstation in one of the production domains, however, the setting does not seem to work. We have tried it under HKCU, HKLM, HKCU\Software\Policies, and HKLM\Software\Policies. It simply seems to be ignored. The value was set in the OCT on a test machine, but the OCT (and the ADM/ADMX file) have the wrong type for the value. We have located the value in the registry and removed it everywhere it is found, we think, and put it back in HKCU, but it still isn't taking. At the moment, a clean Outlook install is not an option - even if it was, we at this point would need to know what to do to fix the pushed copy (I didn't push the copy out to thousands of machines, I've just been asked to help clean up the current mess). Thoughts?

    Read the article

  • Skype can not find libssl.so.10 on 64-bit Fedora Linux

    - by itpastorn
    Skype will not start: $ skype & skype: error while loading shared libraries: libssl.so.10: wrong ELF class: ELFCLASS64 $ ldd /usr/bin/skype |grep ssl libssl.so.10 => not found OK, missing libssl. Where is it? $ ls -l /usr/lib/libssl.so* lrwxrwxrwx. 1 root root ... /usr/lib/libsssl.so -> libcrypto.so.1.0.1e lrwxrwxrwx. 1 root root ... /usr/lib/libssl.so.10 -> libssl.so.6 -rwxr-xr-x. 1 root root ... /usr/lib/libssl.so.1.0.1e lrwxrwxrwx. 1 root root ... /usr/lib/libssl.so.6 -> /usr/lib64/libssl.so.10 OK, it points to libssl.so.6 which in turns points to the 64-bit version. $ ls -l /usr/lib64/libssl.so* lrwxrwxrwx. 1 root root ... /usr/lib64/libssl.so.10 -> libssl.so.1.0.1e -rwxr-xr-x. 1 root root ... /usr/lib64/libssl.so.1.0.1e lrwxrwxrwx. 1 root root ... /usr/lib64/libssl.so.6 -> /usr/lib64/libssl.so.10 So, why is my linkchain not picked up by Skype? (Identical problem exists with libcrypto, BTW).

    Read the article

  • Cannot Delete Item "Could Not Find This Item" issue

    - by aronchick
    A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

    Read the article

  • Google Play Music Not Adding MP3s On-Demand

    - by J0e3gan
    My recent attempts to add music on-demand to Google Play Music have yielded nothing - no "Processing music..." or "Added __ of __" messages, just nothing. Previously I could add music on-demand; and nothing has changed on the machine from which I successfully added music previously, from which I have tried to add music on-demand recently. What could be hampering my ability to add music on-demand? WHAT I'VE TRIED: Right after I started using GPM, I briefly found that I could not add music (on-demand), but the problem went away after a logout/login. This time a logout/login has not helped. Dragging & dropping or browsing to folders or files to add has made no difference either. Nor has waiting ridiculously long for GPM to show signs of life after adding music on-demand seemed to work. Digging deeper, I read a related Google Play Help article and followed its suggestions... ran the Google Play Music Manager troubleshooter = no errors or warnings double checked my available storage = 8 GB free double checked supported file types = MP3 is still supported (of course) ..., but the problem remains. UPDATE: I found that if I configure GPM to automatically upload music added to specific folders, it strangely does add automatically what it will not add on-demand.

    Read the article

  • Ubuntu 11.10 Virtual-box Unity 3D not working

    - by naveen
    After struggling for four hours, I still cannot get Unity 3D of Gnome 3 to work on my VirtualBox - I have been pouring through Internet and forum posts but to no avail. Here's what I've done so far: VirtualBox 4.1.4r74921 on Windows 7 Installed Ubuntu Desktop 11.10 ( 32 bit ) Enabled 3D acceleration Allocated 1.5GB of RAM Allocated 50MB video memory (hope this is not the culprit) Installed Guest edition 4.1.4 Did apt-get update and apt-get upgrade Booted back in to Ubuntu - falls back to Unity 2D Shared folder, mouse integration all works, so guest edition is properly installed Tried the command and below is the output /usr/lib/nux/unity_support_test –p OpenGL vendor string: Mesa Project OpenGL renderer string: Software Rasterizer OpenGL version string: 2.1 Mesa 7.11 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no I am trying to find what the "no" means but cannot find any good answers. Inter Core i5 processor 4GB of RAM on the host Display adapter: NVIDIA GeForce 8400GS Is anyone else facing the same problem? If so, can you point me to a solution or any reference where I can find a solution?

    Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >