Search Results

Search found 12283 results on 492 pages for 'tcp port'.

Page 138/492 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• Allowing ssh in iptables

  - by sat

  I am doing iptables firewall configuration. Actually, I need to allow ssh connection only from particular IP. But, It is blocking the ssh connection. I used the below commands. sat:~# iptables -F sat:~# iptables -A INPUT -p tcp -s src_ip_address -d my_ip_address --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT sat:~# iptables -A INPUT -j DROP sat:~# iptables -nL Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- src_ip_address my_ip_address tcp dpt:22 state NEW,ESTABLISHED DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination If I try to connect from src_ip_address to my_ip_address, it is blocking the connection. Even, It is blocking from my_ip_address to src_ip_address . I haven't put any rules for OUTPUT chain. What is wrong with my commands? How to allow ssh in iptables?

  Read the article

• specific ports in ftp(client)

  - by user158182

  i am using a ftp connection to send data beteen server and client.servers command port is 21 and data port is 20,i want the client port specified by user is that possible, Ftp: command : client >specificport(user defined) --> server --21 data : client >specificport(user defined) --> server --20

  Read the article

• Usb access using c#

  - by Dharavk

  I would like to know how can i read and write data via the Usb port using c#.How do i configure the port ?

  Read the article

• Remotely Schedule and Stream Recorded TV in Windows 7 Media Center

  - by DigitalGeekery

  Have you ever been away from home and suddenly realized you forgot to record your favorite program? Now Windows 7 Media Center, users can schedule recordings remotely from their phones or mobile devices with Remote Potato. How it Works Remote Potato installs server software on the host computer running Windows 7 Media Center. Once the software is installed, we’ll need to do some port forwarding on the router and setup an optional dynamic DNS address. When setup is completed, we will access the application through a web based interface. Silverlight is required for Streaming recorded TV, but scheduling recordings can be done through an HTML interface. Installing Remote Potato Download and install Remote Potato on the Media Center PC. (See download link below) If you plan to stream any Recorded TV, you’ll also want to install the streaming pack located on the same page. It isn’t required to stream all shows, only shows that require the AC3 audio codec. Click Yes to allow Remote Potato to add rules to the Windows Firewall for remote access. You’ll likely need to accept a few UAC prompts. When notified that the rules were added, click OK. Remote Potato will then prompt you to allow administrator privileges to reserve a URL for it’s web server. Click Yes. Remote Potato server will start. Click on the configuration button at the right to to reveal the settings tabs.   One the General tab, you’ll have the option to run Remote Potato on startup and minimized in the System Tray. If you’re running Media Center on a dedicated HTPC, you’ll probably want to enable both startup options. Forwarding Ports on Your Router You’ll need to forward a couple ports on your router. By default, these will be ports 9080 and 9081. In this example we’re using a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Applications & Gaming Tab, and then the Port Range Forward tab. Under Application, type in a name of your choosing. In both the Start and End boxes, type the port number 9080. Enter the local IP address of your Media Center computer in the IP address column. Click the check box under Enable. Repeat the process on the next line, but this time use port 9081. When finished, click the Save Settings button. Note: It’s highly recommended that you configure the home computer running Media Center & Remote Potato with a static IP address.   Find your IP Address You’ll need to find the IP address assigned to your router from your ISP. There are many ways to do this but a quick and easy way is to visit a site like checkip.dyndns.org (link available below) The current external IP address of your router will be displayed in the browser.   Dynamic DNS This is an optional step, but  it’s highly recommended. Many routers, such as the Linksys WRT54GL we are using, support Dynamic DNS (DDNS). What Dynamic DNS allows you to do is affiliate your home router’s external IP address to a domain name. Every time your home router is assigned a a new IP address by your ISP, the domain name is updated to point to your new IP address. Remote Potato’s user interface is accessed over the Internet is by connecting to your router’s IP address followed by a colon and the port number. (Ex: XXX.XXX.XXX.XXX:9080) Instead of constantly having to look up and remember an IP address, you can use DDNS along with a 3rd party provider like DynDNS.com, to sign up for a free domain name and configure it to be updated each time your router is assigned a new IP address. Go to the DynDNS.com website (See link at the end of the article) and sign up for a free Domain name. You’ll need to register and confirm by email.   Once you’ve signed in and selected your domain name click Activate Services. You’ll get a confirmation message that your domain name has been activated.    On the Linksys WRT54GL click on the Setup tab an then DDNS. Select DynDNS.org, or TZO.com if you prefer to use their service, from the drop down list.   With DynDNS, you’ll need to fill in your username and password you signed up with at the DynDNS website and the hostname you chose. Note: You can connect over your local network with the IP Address of the computer running Remote Potato followed by a colon and the port number. Ex: 192.168.1.2:9080 Logging in Remote Potato and Recording a Show Once you connect, you’ll see the start page. To view the TV listings, click on TV Guide. You’ll then see your guide listings. There are a few ways to navigate the listings. At the top left, you can click on any of the preset time buttons to jump to  the listings at that time of the day.  Click on the arrows to the right and left of the day and date at the top center to proceed to the previous or next day. Or, jump to a specific day with the date and date buttons at the top right.   To setup a recording, click on a program.   You can choose to record the individual show or the entire series by clicking on Record Show or Record Series.   Remote Potato on Mobile Devices Perhaps the coolest feature of Remote Potato is the ability to schedule recording from your phone or mobile device. Note: For any devices or computers without Silverlight, you will be prompted to view the HTML page. Select Browse Listings. Select your program to record. In the Program Details, select Record Show to record the single episode or Record Series to record all instances of the series. You will then see a red dot on the program listing to indicate that the show is scheduled for recording.   Streaming Recorded TV Click on Recorded TV from the home screen to access your previously recorded TV programs. Click on the selection you wish to stream. Click on Play. If you receive this error message, you’ll need to install the streaming pack for Remote Potato. This is found on the same download page as installation files. (See link below) The Begin from slider allows you to start playback from the start (by default) or a different time of the program by moving the slider. The Quality (bitrate) setting  allows you to choose the quality of the playback. We found the video quality on the Normal setting to be pretty lousy, and Low was just pointless. High was the best overall viewing experience as it provided smooth quality video playback. We experienced significant stuttering during playback using the Ultra High setting.   Click Start when you are ready to begin. When playback begins you’ll see a slider at the top right.   Move the slider left or right to increase or decrease the size of the video. There’s also a button to switch to full screen.   Media Center users who travel frequently or are always on the go will likely find Remote Potato to be a blessing. Since being released earlier this year, updates for Remote Potato have come fast and furious. The latest beta release includes support for streaming music and photos. If you like those nice network TV logos, check out our article on adding TV channel logos to Windows Media Center. Downloads and Links Download Remote Potato and Streaming Pack Find your IP address Sign Up for a Domain Name at DynDNS.com Similar Articles Productive Geek Tips Schedule Updates for Windows Media CenterUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Add a Sleep Timer to Windows 7 Media CenterStartup Customizations for Media Center in Windows 7Enable Media Streaming in Windows Home Server to Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos

  Read the article

• NEC uPD720200 USB 3.0 not working on Ubuntu 12.04

  - by Jagged

  I've recently installed Ubuntu 12.04 64-bit on a HP Envy 15 1104tx. Most stuff appears to be working fine with the exception of the two USB3 ports (USB2 port works fine). I've read a lot of articles but so far have not been able to find a solution. I've tried adding 'pci=nomsi' to '/etc/default/grub' but this made no difference. Some articles suggest booting into Windows and upgrading the firmware on the uPD720200. Any body had any experience of this? Is there a way I can checked the firmware version of the NEC uPD720200 in Linux to see if there is an update available? Any help appreciated. uname -a: Linux HP-ENVY-15-1104tx 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: hp-envy-15-1104tx description: Notebook product: HP ENVY 15 Notebook PC (WF591PA#ABG) vendor: Hewlett-Packard version: 0492110000241910001420000 serial: CNF0301C79 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=103C_5335KV sku=WF591PA#ABG uuid=434E4630-3330-3143-3739-60EB6906688F *-core description: Motherboard product: 1522 vendor: Hewlett-Packard physical id: 0 version: 36.35 serial: CNF0301C79 slot: Base Board Chassis Location *-firmware description: BIOS vendor: Hewlett-Packard physical id: 0 version: F.2B date: 10/12/2010 size: 1MiB capacity: 1472KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppynec int13floppytoshiba int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int9keyboard int10video acpi usb biosbootspecification *-memory description: System Memory physical id: 13 slot: System board or motherboard size: 16GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 0 serial: E13C4316 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 1 serial: E03C3E16 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 2 serial: 672279CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 3 serial: 652286CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-cpu description: CPU product: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz vendor: Intel Corp. physical id: 1d bus info: cpu@0 version: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz slot: CPU size: 1199MHz capacity: 1199MHz width: 64 bits clock: 1066MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L3 cache physical id: 1e slot: L3 Cache size: 8MiB capacity: 8MiB capabilities: synchronous internal write-through unified *-cache:1 description: L2 cache physical id: 20 slot: L2 Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through unified *-cache:2 description: L1 cache physical id: 21 slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through instruction *-cache description: L1 cache physical id: 1f slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through data *-pci:0 description: Host bridge product: Core Processor DMI vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 11 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Core Processor PCI Express Root Port 1 vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:4000(size=4096) memory:d4100000-d41fffff ioport:c0000000(size=268435456) *-display description: VGA compatible controller product: Broadway PRO [Mobility Radeon HD 5800 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:58 memory:c0000000-cfffffff memory:d4100000-d411ffff ioport:4000(size=256) memory:d4140000-d415ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:56 memory:d4120000-d4123fff *-pci:1 description: PCI bridge product: Core Processor PCI Express Root Port 3 vendor: Intel Corporation physical id: 5 bus info: pci@0000:00:05.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:d4000000-d40fffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:16 memory:d4000000-d4001fff *-generic:0 UNCLAIMED description: System peripheral product: Core Processor System Management Registers vendor: Intel Corporation physical id: 8 bus info: pci@0000:00:08.0 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:1 UNCLAIMED description: System peripheral product: Core Processor Semaphore and Scratchpad Registers vendor: Intel Corporation physical id: 8.1 bus info: pci@0000:00:08.1 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:2 UNCLAIMED description: System peripheral product: Core Processor System Control and Status Registers vendor: Intel Corporation physical id: 8.2 bus info: pci@0000:00:08.2 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:3 UNCLAIMED description: System peripheral product: Core Processor Miscellaneous Registers vendor: Intel Corporation physical id: 8.3 bus info: pci@0000:00:08.3 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:4 UNCLAIMED description: System peripheral product: Core Processor QPI Link vendor: Intel Corporation physical id: 10 bus info: pci@0000:00:10.0 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:5 UNCLAIMED description: System peripheral product: Core Processor QPI Routing and Protocol Registers vendor: Intel Corporation physical id: 10.1 bus info: pci@0000:00:10.1 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:55 memory:d4200000-d4203fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:3000(size=4096) memory:d3000000-d3ffffff ioport:d0000000(size=16777216) *-network description: Wireless interface product: Centrino Advanced-N 6200 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 35 serial: 00:27:10:40:e4:68 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=9.221.4.1 build 25532 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:54 memory:d3000000-d3001fff *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:2000(size=4096) memory:d2000000-d2ffffff ioport:d1000000(size=16777216) *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 60:eb:69:06:68:8f size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=10.161.0.147 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:57 memory:d2000000-d203ffff ioport:2000(size=128) *-usb description: USB controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:20 memory:d4205800-d4205bff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a5 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: RAID bus controller product: 82801 Mobile SATA Controller [RAID mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:5048(size=8) ioport:5054(size=4) ioport:5040(size=8) ioport:5050(size=4) ioport:5020(size=32) memory:d4205000-d42057ff *-disk description: ATA Disk product: OCZ-VERTEX3 physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2.15 serial: OCZ-0350P6H316X5KUQE size: 223GiB (240GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000592dd *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: e741f18c-cfc5-4bce-b1e7-f80e517a3a22 size: 207GiB capacity: 207GiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-06-15 06:49:27 filesystem=ext4 lastmountpoint=/ modified=2012-06-14 21:23:42 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered mounted=2012-07-10 16:18:20 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 15GiB capacity: 15GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 15GiB capabilities: nofs *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:d4205c00-d4205cff ioport:5000(size=32) *-pci:1 description: Host bridge product: Core Processor QuickPath Architecture Generic Non-Core Registers vendor: Intel Corporation physical id: 101 bus info: pci@0000:ff:00.0 version: 04 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Core Processor QuickPath Architecture System Address Decoder vendor: Intel Corporation physical id: 102 bus info: pci@0000:ff:00.1 version: 04 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Core Processor QPI Link 0 vendor: Intel Corporation physical id: 103 bus info: pci@0000:ff:02.0 version: 04 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Core Processor QPI Physical 0 vendor: Intel Corporation physical id: 104 bus info: pci@0000:ff:02.1 version: 04 width: 32 bits clock: 33MHz *-pci:5 description: Host bridge product: Core Processor Integrated Memory Controller vendor: Intel Corporation physical id: 105 bus info: pci@0000:ff:03.0 version: 04 width: 32 bits clock: 33MHz *-pci:6 description: Host bridge product: Core Processor Integrated Memory Controller Target Address Decoder vendor: Intel Corporation physical id: 106 bus info: pci@0000:ff:03.1 version: 04 width: 32 bits clock: 33MHz *-pci:7 description: Host bridge product: Core Processor Integrated Memory Controller Test Registers vendor: Intel Corporation physical id: 107 bus info: pci@0000:ff:03.4 version: 04 width: 32 bits clock: 33MHz *-pci:8 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Control Registers vendor: Intel Corporation physical id: 108 bus info: pci@0000:ff:04.0 version: 04 width: 32 bits clock: 33MHz *-pci:9 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Address Registers vendor: Intel Corporation physical id: 109 bus info: pci@0000:ff:04.1 version: 04 width: 32 bits clock: 33MHz *-pci:10 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Rank Registers vendor: Intel Corporation physical id: 10a bus info: pci@0000:ff:04.2 version: 04 width: 32 bits clock: 33MHz *-pci:11 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers vendor: Intel Corporation physical id: 10b bus info: pci@0000:ff:04.3 version: 04 width: 32 bits clock: 33MHz *-pci:12 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Control Registers vendor: Intel Corporation physical id: 10c bus info: pci@0000:ff:05.0 version: 04 width: 32 bits clock: 33MHz *-pci:13 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Address Registers vendor: Intel Corporation physical id: 10d bus info: pci@0000:ff:05.1 version: 04 width: 32 bits clock: 33MHz *-pci:14 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Rank Registers vendor: Intel Corporation physical id: 10e bus info: pci@0000:ff:05.2 version: 04 width: 32 bits clock: 33MHz *-pci:15 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers vendor: Intel Corporation physical id: 10f bus info: pci@0000:ff:05.3 version: 04 width: 32 bits clock: 33MHz *-battery description: Lithium Ion Battery product: NK06053 vendor: SMP-ATL24 physical id: 1 slot: Primary capacity: 4800mWh configuration: voltage=11.1V lspci: 02:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Hewlett-Packard Company Device 1522 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d4000000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd lsusb (with thumb drive plugged into USB3 port): Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 5986:01d0 Acer, Inc Bus 001 Device 004: ID 03f0:231d Hewlett-Packard

  Read the article

• Ubuntu 11.10 - Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 -- apt-get install openipml openhpi-plugin-ipml

  Read the article

• Implementing the transport layer for a SIP UAC

  - by Jonathan Henson

  I have a somewhat simple, but specific, question about implementing the transport layer for a SIP UAC. Do I expect the response to a request on the same socket that I sent the request on, or do I let the UDP or TCP listener pick up the response and then route it to the correct transaction from there? The RFC does not seem to say anything on the matter. It seems that especially using UDP, which is connection-less, that I should just let the listeners pick up the response, but that seems sort of counter intuitive. Particularly, I have seen plenty of UAC implementations which do not depend on having a Listener in the transport layer. Also, most implementations I have looked at do not have the UAS receiving loop responding on the socket at all. This would tend to indicate that the client should not be expecting a reply on the socket that it sent the request on. For clarification: Suppose my transport layer consists of the following elements: TCPClient (Sends Requests for a UAC via TCP) UDPClient (Sends Requests for a UAC vid UDP) TCPSever (Loop receiving Requests and dispatching to transaction layer via TCP) UDPServer (Loop receiving Requests and dispatching to transaction layer via UDP) Obviously, the *Client sends my Requests. The question is, what receives the Response? The *Client waiting on a recv or recvfrom call on the socket it used to send the request, or the *Server? Conversely, the *Server receives my requests, What sends the Response? The *Client? doesn't this break the roles of each member a bit?

  Read the article

• Best design for a "Command Executer" class

  - by Justin984

  Sorry for the vague title, I couldn't think of a way to condense the question. I am building an application that will run as a background service and intermittently collect data about the system its running on. A second Android controller application will query the system over tcp/ip for statistics about the system. Currently, the background service has a tcp listener class that reads/writes bytes from a socket. When data is received, it raises an event to notify the service. The service takes the bytes, feeds them into a command parser to figure out what is being requested, and then passes the parsed command to a command executer class. When the service receives a "query statistics" command, it should return statistics over the tcp/ip connection. Currently, all of these classes are fully decoupled from each other. But in order for the command executer to return statistics, it will obviously need access to the socket somehow. For reasons I can't completely articulate, it feels wrong for the command executer to have a direct reference to the socket. I'm looking for strategies and/or design patterns I can use to return data over the socket while keeping the classes decoupled, if this is possible. Hopefully this makes sense, please let me know if I can include any info that would make the question easier to understand.

  Read the article

• Help Decide between C#/XNA client or Java

  - by Sparkky

  The game runs on a client/server architecture currently setup for TCP, and the client code was built in AS3 to be web based. What we're running into is 3 problems for the client. AS3 has no hardware acceleration so we are having some issues with slowdown when implementing some features TCP is really frustrating for a sidescroller when you're talking with a server. I'm having a heck of a time with the interpolation/extrapolation to make everyone else look smooth while minimizing lag. I would much rather be able to use UDP and throw in something similar to the age old Quake interpolation/extrapolation. No right click I work professionally with C#, and I did all my University (almost 2 years ago) with Java. Java really appeals to me because of the compatability while C# appeals to me because I've heard so much good about XNA and I love visual studio. For a Client/Server based MMOish sidescroller in your opinion should I stick with AS3 and the TCP protocol, or should I abandon some of my audience, ramp up the graphics and hit C#, or journey back to the land of Java. Thanks :D

  Read the article

• Hudson on debian lenny

  - by Laurent

  Hello, I installed Hudson deamon on one server (running on debian lenny testing) some time ago. All was working until I perform an upgrade. At this time Hudson isn't accessible at port 8080 (which is the default port used). I have looked for iptables problems, however port 8080 is open in INPUT and OUTPUT. Configuration file in /etc/default/hudson seems okay, I haven't touch it. And if I do a ps aux | grep hudson, hudson deamon is running. Update 1: What is really strange for me is that in /var/log/hudson/hudson.log I get no error : [Winstone 2010/02/10 17:10:04] - Control thread shutdown successfully [Winstone 2010/02/10 17:10:04] - Winstone shutdown successfully Running from: /usr/share/hudson/hudson.war [Winstone 2010/02/10 17:10:43] - Beginning extraction from war file hudson home directory: /var/lib/hudson [Winstone 2010/02/10 17:10:44] - HTTP Listener started: port=8080 [Winstone 2010/02/10 17:10:44] - AJP13 Listener started: port=8009 [Winstone 2010/02/10 17:10:44] - Winstone Servlet Engine v0.9.10 running: controlPort=disabled 10 févr. 2010 17:10:44 hudson.model.Hudson$4 onAttained INFO: Started initialization 10 févr. 2010 17:10:44 hudson.model.Hudson$4 onAttained INFO: Listed all plugins 10 févr. 2010 17:10:44 hudson.model.Hudson$4 onAttained INFO: Prepared all plugins 10 févr. 2010 17:10:44 hudson.model.Hudson$4 onAttained INFO: Started all plugins 10 févr. 2010 17:10:46 hudson.model.Hudson$4 onAttained INFO: Loaded all jobs 10 févr. 2010 17:10:46 hudson.model.Hudson$4 onAttained INFO: Completed initialization 10 févr. 2010 17:10:47 org.springframework.context.support.AbstractApplicationContext prepareRefresh INFO: Refreshing org.springframework.web.context.support.StaticWebApplicationContext@caa559d: display name [Root WebApplicationContext]; startup date [Wed Feb 10 17:10:47 CET 2010]; root of context hierarchy 10 févr. 2010 17:10:47 org.springframework.context.support.AbstractApplicationContext obtainFreshBeanFactory INFO: Bean factory for application context [org.springframework.web.context.support.StaticWebApplicationContext@caa559d]: org.springframework.beans.factory.support.DefaultListableBeanFactory@40d2f5f1 10 févr. 2010 17:10:47 org.springframework.beans.factory.support.DefaultListableBeanFactory preInstantiateSingletons INFO: Pre-instantiating singletons in org.springframework.beans.factory.support.DefaultListableBeanFactory@40d2f5f1: defining beans [daoAuthenticationProvider,authenticationManager,userDetailsService]; root of factory hierarchy 10 févr. 2010 17:10:47 org.springframework.context.support.AbstractApplicationContext prepareRefresh INFO: Refreshing org.springframework.web.context.support.StaticWebApplicationContext@4d88a387: display name [Root WebApplicationContext]; startup date [Wed Feb 10 17:10:47 CET 2010]; root of context hierarchy 10 févr. 2010 17:10:47 org.springframework.context.support.AbstractApplicationContext obtainFreshBeanFactory INFO: Bean factory for application context [org.springframework.web.context.support.StaticWebApplicationContext@4d88a387]: org.springframework.beans.factory.support.DefaultListableBeanFactory@6153e0c0 10 févr. 2010 17:10:47 org.springframework.beans.factory.support.DefaultListableBeanFactory preInstantiateSingletons INFO: Pre-instantiating singletons in org.springframework.beans.factory.support.DefaultListableBeanFactory@6153e0c0: defining beans [filter,legacy]; root of factory hierarchy 10 févr. 2010 17:10:47 hudson.TcpSlaveAgentListener <init> INFO: JNLP slave agent listener started on TCP port 59750 Update 2: What I get with lsof -i -n -P | grep hudson: java 28985 hudson 97u IPv6 2002707 0t0 TCP *:8080 (LISTEN) java 28985 hudson 99u IPv6 2002708 0t0 TCP *:8009 (LISTEN) java 28985 hudson 147u IPv6 2002711 0t0 TCP *:59750 (LISTEN) java 28985 hudson 150u IPv6 2002712 0t0 UDP *:33848 I don't know what I can verify. Does someone has an idea in order to help me to resolve this problem ?

  Read the article

• NIC Bonding/balance-rr with Dell PowerConnect 5324

  - by Branden Martin

  I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

  Read the article

• Add a small RAID card? Will it help overall stability and performance of my nine hard drives?

  - by Ray

  Hi, Will I get any extra genuine added performance and RAID stability if I insert a basic RAID card into a PCI-E x1 slot? I am considering the Adaptec 1220SA - 2 port SATA , pci-express (1x) , raid 0/1. Ok it only supports two SATA drives. Purpose is to help support the eight internal hard drives (1TB each), a DVD drive and an external e-SATA connected 2TB hard drive - by dealing with two of the internal hard drives. My current configuration of eight internal 1TB Barracuda (7200.12) SATA hard drives, one external 2TB SATA Western Digital Green Drive (e-SATA) and one DVD drive can already be supported by the Intel P55 & JMicron controllers on the ASUS motherboard : the Intel P55 (controls six HDD; configured as three x RAID 1), and the JMicron (controls two HDD as one RAID 1, as well as the DVD drive and the external SATA drive via the motherboard's e-SATA port (controlled by the JMicron)). Bigger picture details : I have an ASUS motherboard designed for the LGA1156 type processor and it includes the Intel P55 Express Chipset and JMicron. I am using the Intel Core i7-870 processor, and have 8GB DDR3 (1333) memory (four x 2GB Corsair DIMMs). Enough overall power. The power supply is more than sufficicient for the system. Corsair AX850. The system will never need the full 850 watts (future : second graphics card). The RAID card would provide hardware RAID 1 for two of the eight intrnal drives. It would either reduce the load on : the Intel P55 firmware RAID support, or replace the JMicron controller's RAID 1 set. I am busy installing the above configuration using Windows 7 Ultimate 64-bit as the OS. The RAID card is a last minute addition to the plan. Is it worth spending the extra R700 - R900 on the Adaptec 1220SA, or equivalent RAID card? I cannot afford to spend yet another R2000 - R3000 on a RAID card that would support many SATA2 hard drives, with a better RAID, example the RAID 5. My Issue & assumption : I am trusting that the Intel P55 chipset can properly handle six drives, configured as three * RAID 1. I am assuming that the JMicron can handle, using its RED SATA ports, one RAID-1 (two HDDs). The DVD drive connects to the JMicron optical SATA port 1 (white port 1). White port 2 is not used. The e-SATA connection is from the JMicron straight to, and through the motherboard - to an on-board (rear panel) e-SATA port. Am I being a little hopeful in only using the on-board Intel P55 and the JMicron? Is it a waste of money to install a RAID card that handles two SATA2 drives? OR Is it wisdom to take the pressure a little off the Intel P55? Obviously I am interested in data security, hence RAID 1, not RAID Zero. RAID 5 would be nice. The CPU, Intel Core i7-870 will provide the clout. Context to nine drives : I am using virtualisation with Windows 7 Ultimate. Bootable VMs. The operating system gets a mirror. Loaded apps gets a mirror. The current design data is kept in another mirror and Another mirror is back-up one and / or VM territory. Then the external 2TB drive (via e-SATA) is the next layer of data security and then finally, I use off-site data security. Thanks.

  Read the article

• Motion - can't get streaming working from a webcam

  - by Emmanuel Brunet

  I'm trying to record a video stream from my Tenvis IP camera with motion 3.2.12 on Debian 7.5. I used the standard debian package with sudo apt-get install motion Assume my DNS IP cam is webcam, user : admin, password : password /etc/motion/motion.conf Bellow are my configuration file settings : netcam_url http://webcam/videostream.cgi netcam_userpass admin:password target_dir /media/videos/log/motion # The mini-http server listens to this port for requests (default: 0 = disabled) webcam_port 1234 ffmpeg_cap_new on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) webcam_quality 50 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion on # Maximum framerate for webcam streams (default: 1) webcam_maxrate 15 # Restrict webcam connections to localhost only (default: on) webcam_localhost on # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 control_port 8080 control_authentication admin:password Issue #1 when I try display http:/localhost:1234 the browser looks frozen, no HTTP 404 received but it stills waiting for data it seems .. Issue #2 in the output directory motion writes a lot of jpeg snapshots althought I just want to have several video sequenced files. Log I run motion in interactive mode in a terminal, here is the ouput root@mercure:/etc/motion# motion -c motion-1.0.conf [0] Processing thread 0 - config file motion-1.0.conf [0] Motion 3.2.12 Started [0] ffmpeg LIBAVCODEC_BUILD 3482368 LIBAVFORMAT_BUILD 3478785 [0] Thread 1 is from motion-1.0.conf [0] motion-httpd/3.2.12 running, accepting connections [0] motion-httpd: waiting for data on port TCP 8080 [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Operation now in progress [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165303.avi]: Operation now in progress [1] File of type 1 saved to: ~/tmp/motion/01-20140603165303-01.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Resource temporarily unavailable [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165329.avi]: Resource temporarily unavailable [1] File of type 1 saved to: ~/tmp/motion/01-20140603165329-00.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Connection reset by peer [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165355.avi]: Connection reset by peer [1] File of type 1 saved to: ~/tmp/motion/01-20140603165355-06.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [0] httpd - Finishing [0] httpd Closing [0] httpd thread exit [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 It doesn't find the codec ... avcodec_open - could not open codec: Operation now in progress I've changed fmpeg_video_codec from mpeg4 to swf the result is the same. When using flv format motion writes a lot of .jpg image but I can't see anything at http://localhost:1234 [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-00.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-01.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-02.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-03.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-04.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-05.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-06.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-00.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-01.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-02.jpg Any idea just to get the video stream recoded on my local disk ?

  Read the article

• Tomcat and ASP site under IIS6 with SSL

  - by Rafe

  I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

  Read the article

• RMI applet is making requests on random ports and blocked consequently

  - by Dan

  /// I have set up RMI system successfully on local ubuntu srver. Registry port 1099 and remote object export on 1100(fixed by calling super(1100)) Now I am trying to make it work on Ubuntu over internet with a public IP. I could bind service properly with public ip.But the client applet is trying to connect to ubuntu server at random ports. Below is the error thrown by client applet: // Exception network: Connecting public-ip:1100 with proxy=DIRECT network: Connecting public-ip/cgi-bin/java-rmi.cgi?forward=1099 with proxy=DIRECT network: Connecting public-ip:3733 with proxy=DIRECT network: Connecting public-ip:3721 with proxy=DIRECT // java.rmi.ConnectException: Connection refused to host: public-ip; nested exception is: java.net.ConnectException: Connection refused: connect at sun.rmi.transport.tcp.TCPEndpoint.newSocket(Unknown Source)Source) at java.net.AbstractPlainSocketImpl.connectToAddress(Unknown Source) ... // // I have only 2 ports open on server, i.e., 1099(registry) and 1100(export). How can I fix ports in applet requests such that it does always connect server on same open port? // // Another issue.As I have bound service on public IP i.e. //public-ip:1099/ServiceName, a job running on server to send message to clinets is not able to make request to RMI service. public-ip URL does not work on same machine,i.e., server.Do you think I should use fixed socket factory?If so please give me code snippet and guide me how i can set it up. //Exception java.rmi.ConnectException: Connection refused to host: public-ip; nested exception is: java.net.ConnectException: Connection refused at sun.rmi.transport.tcp.TCPEndpoint.newSocket(TCPEndpoint.java:619) at sun.rmi.transport.tcp.TCPChannel.createConnection(TCPChannel.java:216) at sun.rmi.transport.tcp.TCPChannel.newConnection(TCPChannel.java:202) at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:128) at java.rmi.server.RemoteObjectInvocationHandler.invokeRemoteMethod(RemoteObjectInvocationHandler.java:194) at java.rmi.server.RemoteObjectInvocationHandler.invoke(RemoteObjectInvocationHandler.java:148) at $Proxy5.getUserID(Unknown Source) at rmi.source.xxxxxx$JobScheduler.run(xxxxServerImpl.java:293) at java.util.TimerThread.mainLoop(Timer.java:555) at java.util.TimerThread.run(Timer.java:505) Caused by: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.AbstractPlainSocketImpl.doConnect(AbstractPlainSocketImpl.java:337) at java.net.AbstractPlainSocketImpl.connectToAddress(AbstractPlainSocketImpl.java:198) at java.net.AbstractPlainSocketImpl.connect(AbstractPlainSocketImpl.java:180) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:391) at java.net.Socket.connect(Socket.java:579) at java.net.Socket.connect(Socket.java:528) at java.net.Socket.(Socket.java:425) at java.net.Socket.(Socket.java:208) at sun.rmi.transport.proxy.RMIDirectSocketFactory.createSocket(RMIDirectSocketFactory.java:40) at sun.rmi.transport.proxy.RMIMasterSocketFactory.createSocket(RMIMasterSocketFactory.java:146) at sun.rmi.transport.tcp.TCPEndpoint.newSocket(TCPEndpoint.java:613) ... 9 more Coould you please help me? Thanks a lot in advance. Dan

  Read the article

• Maximum nametable char count exceeded

  - by doc

  I'm having issues with the maximum nametable char count quota, I followed a couple of answers here and it solved the problem for a while, but now I'm having the same issue. My Server side config is as follows: <system.serviceModel> <bindings> <netTcpBinding> <binding name="GenericBinding" maxBufferPoolSize="2147483647" maxBufferSize="2147483647" maxReceivedMessageSize="2147483647"> <readerQuotas maxDepth="2147483647" maxStringContentLength="2147483647" maxArrayLength="2147483647" maxBytesPerRead="2147483647" maxNameTableCharCount="2147483647" /> <security mode="None" /> </binding> </netTcpBinding> </bindings> <behaviors> <serviceBehaviors> <behavior> <serviceMetadata httpGetEnabled="false" /> <serviceDebug includeExceptionDetailInFaults="true" /> <dataContractSerializer maxItemsInObjectGraph="1000000" /> </behavior> </serviceBehaviors> </behaviors> <services> <service name="REMWCF.RemWCFSvc"> <endpoint address="" binding="netTcpBinding" contract="REMWCF.IRemWCFSvc" bindingConfiguration="GenericBinding" /> <endpoint address="mex" binding="mexTcpBinding" contract="IMetadataExchange" /> <host> <baseAddresses> <add baseAddress="net.tcp://localhost:9081/RemWCFSvc" /> </baseAddresses> </host> </service> </services> </system.serviceModel> I also have the same tcp binding on the devenv configuration. Have I reached the limit of contracts supported? Is there a way to turn off that quota? EDIT Error Message: Error: Cannot obtain Metadata from net.tcp://localhost:9081/RemWCFSvc/mex If this is a Windows (R) Communication Foundation service to which you have access, please check that you have enabled metadata publishing at the specified address. For help enabling metadata publishing, please refer to the MSDN documentation at http://go.microsoft.com/fwlink/?LinkId=65455.WS-Metadata Exchange Error URI: net.tcp://localhost:9081/RemWCFSvc/mex Metadata contains a reference that cannot be resolved: 'net.tcp://localhost:9081/RemWCFSvc/mex'. There is an error in the XML document. The maximum nametable character count quota (16384) has been exceeded while reading XML data. The nametable is a data structure used to store strings encountered during XML processing - long XML documents with non-repeating element names, attribute names and attribute values may trigger this quota. This quota may be increased by changing the MaxNameTableCharCount property on the XmlDictionaryReaderQuotas object used when creating the XML reader. I'm getting that error when trying to run the WCF (which is hosted in a windows service app).

  Read the article

• PHP Sockets Errors (connection refused and No such file or directory)

  - by Purefan

  Hello all, I am writing a server app (broadcaster) and a client (relayer). Several relayers can connect to the broadcaster at the same time, send information and the broadcaster will redirect the message to a matching relayer (for example relayer1 sends to broadcaster who sends to relayer43, relayer2 - broadcaster - relayer73...) The server part is working as I have tested it with a telnet client and although its at this point only an echo server it works. Both relayer and broadcaster sit on the same server so I am using AF_UNIX sockets, both files are in different folders though. I have tried two approaches for the relayer and both have failed, the first one is using socket_create: public function __construct() { // where is the socket server? $this->_sHost = 'tcp://127.0.0.1'; $this->_iPort = 11225; // open a client connection $this->_hSocket = socket_create(AF_UNIX, SOCK_STREAM, 0); echo 'Attempting to connect to '.$this->_sHost.' on port '.$this->_iPort .'...'; $result = socket_connect($this->_hSocket, $this->_sHost, $this->_iPort); if ($result === false) { echo "socket_connect() failed.\nReason: ($result) " . socket_strerror(socket_last_error($this->_hSocket)) . "\n"; } else { echo "OK.\n"; } This returns "Warning: socket_connect(): unable to connect [2]: No such file or directory in relayer.class.php on line 27" and (its running from command line) it often also returns a segmentation fault. The second approach is using pfsockopen: public function __construct() { // where is the socket server? $this->_sHost = 'tcp://127.0.0.1'; $this->_iPort = 11225; // open a client connection $fp = pfsockopen ($this->_sHost, $this->_iPort, $errno, $errstr); if (!$fp) { $result = "Error: could not open socket connection"; } else { // get the welcome message fgets ($fp, 1024); // write the user string to the socket fputs ($fp, 'Message ' . __LINE__); // get the result $result .= fgets ($fp, 1024); // close the connection fputs ($fp, "END"); fclose ($fp); // trim the result and remove the starting ? $result = trim($result); $result = substr($result, 2); // now print it to the browser } which only returns the error "Warning: pfsockopen(): unable to connect to tcp://127.0.0.1:11225 (Connection refused) in relayer.class.php on line 33 " In all tests I have tried with different host names, 127.0.0.1, localhost, tcp://127.0.0.1, 192.168.0.199, tcp://192.168.0.199, none of it has worked. Any ideas on this?

  Read the article

• how to allow certain packet with certian destination ports to forward using iptables?

  - by moataz metwally

  i have server and i virualized it into multiple windws vps's using kvm. i would like to make all vps behind the server firewall. to control all the ports of all vps's from the host server.i have tried to do this by that iptables file but it still blocking all the forward packets. when i remove -A FORWARD -j DROP from the file the vps will be out of the firewall control : # Generated by iptables-save v1.4.7 on Mon Oct 21 04:30:35 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [49:7546] -A OUTPUT -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp -m multiport --dports 5901:6010,4080:4085 -j ACCEPT -A FORWARD -p tcp -s 0/0 -d 0/0 --destination-port 3389 -j ACCEPT -A INPUT -j DROP -A FORWARD -j DROP COMMIT # Completed on Mon Oct 21 04:30:35 2013 and my ifconfig output: eth0 Link encap:Ethernet HWaddr 6C:62:6D:EF:B8:77 inet6 addr: fe80::6e62:XXX:feef:b877/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4460000 errors:0 dropped:0 overruns:0 frame:0 TX packets:1825697 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5461498823 (5.0 GiB) TX bytes:547852516 (522.4 MiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6380 errors:0 dropped:0 overruns:0 frame:0 TX packets:6380 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6481652 (6.1 MiB) TX bytes:6481652 (6.1 MiB) natbr2 Link encap:Ethernet HWaddr 52:54:00:48:72:53 inet addr:88.XXX.XXX.X53 Bcast:88.198.242.159 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1338720 errors:0 dropped:0 overruns:0 frame:0 TX packets:3570844 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:434791198 (414.6 MiB) TX bytes:4321751647 (4.0 GiB) viif1001 Link encap:Ethernet HWaddr FE:16:3E:0F:41:D8 inet6 addr: fe80::fc16:XXX:fe0f:41d8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:358229 errors:0 dropped:0 overruns:0 frame:0 TX packets:479289 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:50127351 (47.8 MiB) TX bytes:261223068 (249.1 MiB) viif1002 Link encap:Ethernet HWaddr FE:16:3E:EA:65:FA inet6 addr: fe80::fc16:XXX:feea:65fa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:575590 errors:0 dropped:0 overruns:0 frame:0 TX packets:1489296 errors:0 dropped:0 overruns:5412 carrier:0 collisions:0 txqueuelen:500 RX bytes:243629668 (232.3 MiB) TX bytes:1724640936 (1.6 GiB) viif1003 Link encap:Ethernet HWaddr FE:16:3E:2B:85:0E inet6 addr: fe80::fc16:XXX:fe2b:850e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:413052 errors:0 dropped:0 overruns:0 frame:0 TX packets:1741801 errors:0 dropped:0 overruns:299 carrier:0 collisions:0 txqueuelen:500 RX bytes:147931054 (141.0 MiB) TX bytes:2338132498 (2.1 GiB) viifbr0 Link encap:Ethernet HWaddr 6C:62:6D:EF:B8:77 inet addr:176.XX.XX.X9 Bcast:176.9.0.95 Mask:255.255.255.224 inet6 addr: fe80::6e62:XXX:feef:b877/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2685666 errors:0 dropped:0 overruns:0 frame:0 TX packets:1472089 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4244043694 (3.9 GiB) TX bytes:523110523 (498.8 MiB)

  Read the article

• Unable to ssh out anywhere - ssh_exchange_identification

  - by Chowlett

  I have a setup where I'm running Ubuntu 11.10 as a VirtualBox guest under a Windows 7 host, behind a restrictive corporate firewall. I have set up NAT from the host port 22 to Ubuntu's port 22; IT inform me that they have opened port 22 outbound for the host machine's IP address. I have run ssh-keygen -t rsa, and am trying to test the setup by connecting to github and another known ssh server. In both cases the connect is refused with ssh_exchange_identification: Connection closed by remote host. Full -vvv log is below. Is this possibly still due to the corporate firewall? If so, what else might I need to request from them? Any other ideas what might be wrong and how to fix it? ~$ ssh -Tvvv [email protected] OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug3: Incorrect RSA1 identifier debug3: Could not load "/home/chris/.ssh/id_rsa" as a RSA1 public key debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'Proc-Type:' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'DEK-Info:' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/chris/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/chris/.ssh/id_rsa-cert type -1 debug1: identity file /home/chris/.ssh/id_dsa type -1 debug1: identity file /home/chris/.ssh/id_dsa-cert type -1 debug1: identity file /home/chris/.ssh/id_ecdsa type -1 debug1: identity file /home/chris/.ssh/id_ecdsa-cert type -1 ssh_exchange_identification: Connection closed by remote host Edit: Requested diagnostics: ~$ ls -la ~/.ssh total 16 drwx------ 2 chris chris 4096 2012-03-30 13:12 . drwxr-xr-x 29 chris chris 4096 2012-03-30 13:25 .. -rw------- 1 chris chris 1766 2012-03-30 13:12 id_rsa -rw-r--r-- 1 chris chris 409 2012-03-30 13:12 id_rsa.pub

  Read the article

• dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

  - by kce

  We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

  Read the article

• Sun Ray 3 Plus Appliance Announced

  - by [email protected]

  There were many of you out there wondering if Oracle was going to keep and add to the Sun Ray and Sun virtualized desktop product suite, there have been a number of affirmative statements over the last many months. However, none of them resound like this; the introduction of a new product pretty much proves the point. A couple minutes before 3:00, local time yesterday, Oracle announced the release of a new Sun Ray, appliance, the Sun Ray 3 Plus. This is the unit that will replace the SR 2 FS (which has been for sale now since the middle of last decade).  Physically it is about the same size as the 2 FS but there are some significant differences... As you can see there is no smart card reader in the front - that has moved to the top to ensure only one hand is required to insert the card.  There is also a larger surround on the card reader that lights up to show the user the card is being read (properly).  A new power on/off switch is on the front which essentially brings power consumption to ~0 watts, but there is also a new 'sleep' timer looking for 30 minutes of inactivity and then will drop the power consumption down to ~ 1watt. There are also 2 USB 2.0 ports are accessible on the front instead of one.  The standard mic in and headphone out ports are there as well.  There is even more interesting stuff on the back. From the top down there are two more USB 2.0 ports for a total of four, but then the Oracle "Peripheral Kit" keyboard includes a 3-port USB Hub, too.  There's a 10/100/1000 Ethernet port as well as a 1000 Mb SFP port.  Standard DB-9 Serial port and then two DVI ports.  Then there is the really big news.  Two DVI ports driving 2560 x 1600 resolution, each. Most PCs can't do that without adding an adapter card.Now the images I have here are ones taken on a prototype a couple months back.  They are essentially the same as the Production unit, but if you would like to see an image of the Production Sun Ray 3 Plus unit you can see one here. There is a full data sheet available here. So this is the first Oracle Sun Ray desktop appliance.  Proof that the product line lives on.  A very good start!

  Read the article

• Configure 27" 2560x1440 for a monitor with corrupt EDID

  - by Aras

  I am trying to get a monitor work with my Ubuntu laptop. The monitor is this cheap 27" Korean monitors which has a 2560x1440 resolution -- and nothing else. Here are some specifications of this monitor: 2560x1440 @60Hz Only one dual link DVI-D input -- no other input port (no HDMI or display port) no OSD no scalar reports corrupt EDID does 2560x1440 @60Hz, did I say that already? Anyways, the monitor works beautifully with my Ubuntu desktop which has an nVidia card with DVI output. However, I am having problem using this monitor with my laptop. After some searching around I found a few posts suggesting to use an active adaptor for mini display port, so I went and bought a mini display to dual link DVI-D adaptor.. When using this adaptor the monitor is recognized by nvidia-settings tool but with incorrect resolution information. As you can see the monitor is incorrectly recognized and there are no other resolution available to set. This post on ubuntu forums and this other post on overclock both suggest that the monitor is reporting corrupt EDID file. I have tried following their instructions, but so far I have not been able to display any image on the monitor from my laptop. The laptop I am using is an ASUS G75VW with a 1920x1080 screen. It has a VGA, an HDMI 1.4a, and a mini display port. The graphic card is an nvidia gforce gtx 660M with 2GB dedicated memory. I am running Ubuntu 12.10 on here which I upgrade from 12.04 a few weeks ago. As I said I have tried several suggestions, including specifying Modeline in xorg.conf and also linking to EDID files I found from those forum posts above. However, I am not sure if the EDID files I found are suitable for my monitor. I think the solution to my problem consist of obtaining the EDID file of my monitor and then fixing it and modifying xorg.conf to force nvidia driver to load the correct resolution. However, I am not sure what steps I need to take to do this. Here is the part of sudo xrandr --prop output that is related to this monitor: DP-1 connected 800x600+1920+0 (normal left inverted right x axis y axis) 0mm x 0mm SignalFormat: DisplayPort supported: DisplayPort ConnectorType: DisplayPort ConnectorNumber: 3 (0x00000003) _ConnectorLocation: 3 (0x00000003) 800x600 60.3*+ I was expecting to see the EDID file in this output as was mentioned in this post, but it is not there. After several hours of tweaking X configurations, I decided it was time to ask for help here. I would really appreciate if someone with experience regarding EDID and X configuration could give me a hand to solve this issue.

  Read the article

• iptables (NAT/PAT) setup for SSH & Samba

  - by IanVaughan

  I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - B1 = 192.168.109.15 B2 = 172.24.40.130 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Update after response from Eddie Few problems (and Machines' B IP is different!) From A :- ssh 172.24.40.130 works ok, (can get to B2) but ssh 172.24.40.130 -p 2022 -vv times out with :- OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.24.40.130 [172.24.40.130] port 2022. ...wait ages... debug1: connect to address 172.24.40.130 port 2022: Connection timed out ssh: connect to host 172.24.40.130 port 2022: Connection timed out From B2 :- $ service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 192.168.0.2 tcp dpt:22 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:2022 to:192.168.0.2:22 Chain POSTROUTING (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination And ssh from B2 to C works fine :- $ ssh 192.168.0.2 Route info :- $ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 172.24.40.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth1 default 172.24.40.1 0.0.0.0 UG 0 0 0 eth0 $ ip route 192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1 172.24.40.0/24 dev eth0 proto kernel scope link src 172.24.40.130 169.254.0.0/16 dev eth1 scope link default via 172.24.40.1 dev eth0 So I just dont know why the port forward doesnt work from A to B2?

  Read the article

• Directory listing through FTPS (TLS) is not working

  - by Aron Rotteveel

  We recently switched our server to require TLS for every connection. This is working flawlessly so far, but one of our clients is having problems. Some facts: Server uses Pure-FTPD Server has a passive port range configured Server has no firewall limitations regarding the FTP Client uses WS FTP Client is behind a router Client connects to the same IP as every other, using PASSIVE mode All other clients have no trouble connecting Because of the TLS requirement, connecting using ACTIVE mode is almost not possible, but PASSIVE is working fine for everyone except this specific client. It seems that he is able to connect, but once a LIST command is performed, things go wrong. Log: Finding Host <clienthost> ... Connecting to <serverip:21> Connected to <serverip:21> in 0.020000 seconds, Waiting for Server Response Initializing SSL Session ... 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- 220-You are user number 5 of 50 allowed. 220-Local time is now 22:14. Server port: 21. 220-This is a private system - No anonymous login 220-IPv6 connections are also welcome on this server. 220 You will be disconnected after 15 minutes of inactivity. AUTH TLS 234 AUTH TLS OK. SSL session NOT set for reuse SSL Session Started. Host type (1): Automatic Detect USER <user> 331 User <user> OK. Password required PASS (hidden) 230-User <user> has group access to: <user> 230 OK. Current restricted directory is / SYST 215 UNIX Type: L8 Host type (2): Unix (Standard) PBSZ 0 200 PBSZ=0 PROT P 200 Data protection level set to "private" PWD 257 "/" is your current location CWD /public_html 250 OK. Current directory is /public_html PWD257 "/public_html" is your current location TYPE A 200 TYPE is now ASCII PASV 227 Entering Passive Mode (<serverip>,132,100) connecting data channel to <serverip>:132,100(33892) Substituting connection address <serverip> for private address <serverip> from PASV Using external address <customer ext. ip> instead of local address <customer int. ip> for PORT command PORT 82,161,56,225,195,181 200 PORT command successful LIST Error reading response from server. It appears that the connection is dead. Attempting reconnect... Any help is appreciated.

  Read the article

• How do I protect a low budget network from rogue DHCP servers?

  - by Kenned

  I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >