Search Results

Search found 60556 results on 2423 pages for 'access list'.

Page 14/2423 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• Recommendation on remote access setup for accessing customer systems

  - by gregmac

  I'm looking for a product recommendation (open or commercial) that will allow remote access to customer sites for tech support purposes. We need to be able to gain access to help troubleshoot problems on servers. Currently end up using anything from RDP on public IP, to various VPNs that clients happen to have, to webex-type sessions that require lots of interaction from both sides to get things working. This often means a problem that could take 10 minutes to solve takes an extra 30+ minutes messing around trying to get a connection up. There are multiple customer sites, which should NOT have access to each other. At each site, there is anywhere from 1 to 8 servers (Windows 2003 or 2008) that need to be accessed. Support connection to machines even if they're behind a firewall/router with no public IP Be able to selectively allow/deny access from customer site. Customer site should not be able to connect outbound to anywhere else (our systems, or other customer sites) Support multiple users from our end If not a VPN connection (where RDP could be used over top), should support: Remote desktop access, including copy/paste File transfers Preferably would have some way to list all remote systems, showing online/offline. Anyone have any suggestions?

  Read the article

• Grant HTTP access based on unix user group

  - by Sander Marechal

  Is it possible to grant network access or HTTP access based on a user's group? At my company we want to set up an internal composer server using Satis to manage packages for the projects we write (e.g. on repository.mycompany.com), with the packages themselves in our SVN server (svn.mycompany.com). We have several webservers with many different users on them. Some users should be able to reach the composer and SVN server. Some should not. Users that should be able to reach these servers all belong to the same group. How can I set up Apache on the Composer and SVN server to only grant access to those users in that group? Alternatively, can I set up the webservers in such a way that only users from that group are able to make a connection to our Composer and SVN servers? The best thing we have come up with so far is using SSL client certificates. We simply place a client certificate on all servers which can be used to access Composer and SVN. Only the right usergroup will have read access to the certificate. A bit clunky but it may work. But I'm looking for something better.

  Read the article

• Cannot access an application folder in Program files

  - by GiddyUpHorsey

  I recently installed Windows 7 Professional 64bit on a new machine. I installed an application using a ClickOnce installer. The application runs fine, but I cannot access the application folder it created in c:\Program files (x86). It bombs with access denied. I try to view the properties on the folder and it takes about 1 minute to display (other folders take 1 second). It says I cannot view any information because I'm not the owner. It doesn't say who the current owner is (instead - Unable to display current owner.) but says I can take ownership. When I try it fails again with Access Denied, even though I have administrative permissions. Why can't I access this folder nor take ownership?

  Read the article

• Access control to non root users

  - by Sirish Kumar

  Hi I am setting up development environment based on SLED, we have installed required software as root user. We have configuered users Login through NIS. Developers needs access to almost all partitions for complete access including write and execute when they login using their ID's, Log in through their own id's is mandatory . What is the best way to give this access?

  Read the article

• Difference between indoor and outdoor WiFi Access Points

  - by aaron-cook

  Does anyone know if there is an operational difference between what is classified as an 'indoor' wifi access point and an 'outdoor' wifi access point. I'm speaking specifically to its operation rather than things like whether its enclosure is weather proof or not. And I'm also referring to the access point itself as opposed to the antenna used.

  Read the article

• resolve access violation exception (0xC0000005) crashing IIS app pool

  - by Joseph

  IIS 7.5, server 2008 r2, classic asp and asp .net 2.0, 3.5 website same server, same app pool. The past 4 weeks thousands of these errors 'C0000005' are occurring. I know from IIS debug diag tool that 'C0000005' is an access violation error. Below is the top line from my debug diag report. In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 Thread 29 - System ID 6736 Entry point 0x00000000 Create time 1/8/2011 12:46:26 AM Time spent in user mode 0 Days 00:00:00.140 Time spent in kernel mode 0 Days 00:00:00.078 Function Source asp!CActiveScriptEngine::GetApplication+27 vbscript!COleScript::GetDebugApplicationCoreNoRef+2b vbscript!COleScript::FDebuggerEnabled+30 vbscript!COleScript::SetScriptSite+cd asp!CActiveScriptEngine::Init+125 asp!CScriptManager::GetEngine+252 asp!AllocAndLoadEngines+28f asp!ExecuteGlobal+17a asp!Execute+b5 asp!CHitObj::ViperAsyncCallback+3fc asp!CViperAsyncRequest::OnCall+6a comsvcs!CSTAActivityWork::STAActivityWorkHelper+32 ole32!EnterForCallback+f4 ole32!SwitchForCallback+1a8 ole32!PerformCallback+a3 ole32!CObjectContext::InternalContextCallback+15b ole32!CObjectContext::DoCallback+1c comsvcs!CSTAActivityWork::DoWork+12f comsvcs!CSTAThread::DoWork+18 comsvcs!CSTAThread::ProcessQueueWork+37 comsvcs!CSTAThread::WorkerLoop+135 msvcrt!_endthreadex+44 msvcrt!_endthreadex+ce kernel32!BaseThreadInitThunk+e ntdll!__RtlUserThreadStart+70 ntdll!_RtlUserThreadStart+1b BELOW is the faulting module. ASP report Executing ASP requests 0 Request(s) ASP templates cached 0 Template(s) ASP template cache size 0.00 Bytes Loaded ASP applications 1 Application(s) ASP.DLL Version 7.5.7600.16620 ASP application report ASP application metabase key Physical Path Virtual Root Session Count 0 Session(s) Request Count 0 Request(s) Session Timeout 0 minutes(s) Path to Global.asa Server side script debugging enabled False Client side script debugging enabled False Out of process COM servers allowed False Session state turned on False Write buffering turned on False Application restart enabled False Parent paths enabled False ASP Script error messages will be sent to browser False ASP!CACTIVESCRIPTENGINE::GETAPPLICATION+27In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 recent events: server was being brute forced by hackers all of Dec and probably earlier, they weren't able to gain access but did get a virus on and blasted out spam. insatlled AVG and about the 17 or 22 latest patches. after that the app pool started crashing and the server has crashed a couple times since then. I am in no mans land as I am a developer and not a sys admin but I have to assume many roles. So I'm reaching out for help. Sometimes I will see hundreds of these 'C0000005' scriptengine errors in the event log in a matter of seconds and other times just a few times an hour. I googled this line 'ASP!CACTIVESCRIPTENGINE::GETAPPLICATION' and got nothing. Its like the function don't exist or something. I have spent many hours google-ing to no avail and am now turning to the experts on the forums. Thank you for your help

  Read the article

• Iterator for second to last element in a list

  - by BSchlinker

  I currently have the following for loop: for(list<string>::iterator jt=it->begin(); jt!=it->end()-1; jt++) I have a list of strings which is in a larger list (list<list<string> >). I want to loop through the contents of the innerlist until I get to the 2nd to last element. This is because I have already processed the contents of the final element, and have no reason to process them again. However, using it->end()-1 is invalid -- I cannot use the - operator here. While I could use the -- operator, this would decrement this final iterator on each cycle. I believe a STL list is a doubly linked list, so from my perspective, it should be possible to do this. Advice? Thanks in advance

  Read the article

• Connecting multiple access points

  - by mohsen farahanipoor

  I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

  Read the article

• Dropdown in Access 2007 parameter query. Why not working

  - by waanders

  Hello, I want a Access parameter query to ask an user for a value (a location in this case). When I type [Enter location] in the Criteria field it works fine: I get a dialog box (Enter Parameter Value) with a textbox and my text (Enter Location). So far, so good. This works (the result also). But now I want a dropdown/combobox (instead of a textbox ) for the user to pick a location. I made a form and type Forms![Form1]![CmbLocation] in the Criteria field. Like this: http://office.microsoft.com/en-us/access/HA011170771033.aspx But I still get a textbox (with the reference as textlabel). What am I doing wrong? Has anybody any advice?

  Read the article

• Query a List of List of Items in LINQ c#

  - by call me Steve

  I am a bit new to LINQ, here is my problem. I have a List of List of Items I like to get the Items which are present in only one List (and if I could get the List in which they are without re-iterating through the "list of list" that would be great). I am trying without success to use the Aggregate / Except / Group keywords in the Linq query but nothing close to a solution so far.

  Read the article

• Cannot access an application folder in Program files

  - by GiddyUpHorsey

  I recently installed Windows 7 Professional 64bit on a new machine. I installed an application using a ClickOnce installer. The application runs fine, but I cannot access the application folder it created in c:\Program files (x86). It bombs with access denied. I try to view the properties on the folder and it takes about 1 minute to display (other folders take 1 second). It says I cannot view any information because I'm not the owner. It doesn't say who the current owner is (instead - Unable to display current owner.) but says I can take ownership. When I try it fails again with Access Denied, even though I have administrative permissions. Why can't I access this folder nor take ownership?

  Read the article

• Merge object from list by comparing one value

  - by Bala

  I have two List of Objects (one is master list and other is error list) and if there is a match of one value when compared two lists then merge all other error list values into mast list value (only one object). Other than iterating is there any other way to compare a value and then merge that object. Object is a Value object with some setters and getters. Appreciate your help. List<OrderVO> masterList; List<OrderVO> errorList; If errorList.OrderVO.getOrderID = masterList.OrderVO.getOrderID then masterList.OrderVO.merge(errorList.OrderVO) or copy all values of masterList.OrderVO.copy(errorList.OrderVO). Hoper this is clear

  Read the article

• Dividing a list in specific number of sublists

  - by Surya

  I want to divide a list in "a specific number of" sublists. That is, for example if I have a list List(34, 11, 23, 1, 9, 83, 5) and the number of sublists expected is 3 then I want List(List(34, 11), List(23, 1), List(9, 83, 5)). How do I go about doing this? I tried grouped but it doesn't seem to be doing what I want. PS: This is not a homework question. Kindly give a direct solution instead of some vague suggestions.

  Read the article

• Printing a list using reflection

  - by TFool

  public class Service{ String serviceName; //setter and getter } public class Version{ String VersionID; //setter and getter } public void test(Object list){ //it shd print the obtained list } List< Service list1; //Service is a Bean List< Version list2; //Version is a Bean test(list1); test(list2); Now the test method shd print the obtained list - (i.e) If the list is of type Service ,then serviceName should be printed using its getter. If the list type is Version versionID should be printed. Is it possible to achieve this without using Interface or abstract class?

  Read the article

• Body of email breaks distribution list in exchange?

  - by widgisoft

  Hi, I have a very odd problem that I'm not sure is a programming issue or a server issue :-p. Basically I'm sending an email to an exchange distribution list that includes a PHP stack trace; during certain faults the trace includes really high level information such as the machine's environment variables (during file reads, etc.). I went through a copy of the email line by line until the email sent and it appears the line: [SUDO_COMMAND] => /etc/init.d/httpd restart is the culprit. Adding a string replacement in before the email is sent allows a successful send. What I don't understand is WHY these stream of characters are causing the issue ONLY on the distribution email. If I send the email to myself as well, i.e. "[email protected]; [email protected]", then I get the email fine. Re-ordering the list doesn't make a difference the group never gets the email. Because the individual gets the email and not the group I'm assuming the fault is with exchange and some rogue filtering - I've gone through it with the sysadmins and there's no filtering of any sort on that group... so maybe it's a bug? I can't find anyone else having recorded this specific fault so I figured I'd open it here. For now I'm just not using the distribution list but it'd be nice to eventually find the solution. Many thanks, Chris

  Read the article

• Format all elements of a list

  - by Curious2learn

  I want to print a list of numbers, but I want to format each member of the list before it is printed. For example, theList=[1.343465432, 7.423334343, 6.967997797, 4.5522577] I want the following output printed given the above list as an input: [1.34, 7.42, 6.97, 4.55] For any one member of the list, I know I can format it by using, print "%.2f" % member Is there a command/function that can do this for the whole list. I can write one, but was wondering if one already exists. Thanks.

  Read the article

• Combining List<>'s in .NET

  - by Maxim Z.

  I have a few List< objects that hold many objects of one specific type. My goal is to combine these List<'s into one List<. Of course, I could just loop through each List's contents and add them into one final List, but is there a more efficient way?

  Read the article

• std::list or std::multimap

  - by Tamir

  Hey, I right now have a list of a struct that I made, I sort this list everytime I add a new object, using the std::list sort method. I want to know what would be faster, using a std::multimap for this or std::list, since I'm iterating the whole list every frame (I am making a game). I would like to hear your opinion, for what should I use for this incident.

  Read the article

• How to slice a list of objects in association of the object attributes

  - by gizgok

  I have a list of fixtures.Each fixture has a home club and a away club attribute.I want to slice the list in association of its home club and away club.The sliced list should be of homeclub items and awayclub items. Easier way to implement this is to first slice a list of fixtures.Then make a new list of the corresponding Home Clubs and Away Clubs.I wanted to know if we can do this one step.

  Read the article

• python how to find the median of a list

  - by user3450574

  I'm trying to write a function named median that takes a list as an input and returns the median value of the list. I'm working with Python 2.7.2 The list can be of any size and the numbers are not guaranteed to be in any particular order. If the list contains an even number of elements, the function should return the average of the middle two. This is the code I'm starting with: def median(list): print(median([7,12,3,1,6,9]))

  Read the article

• MS Access 2003: Can data disappear from records and how do I test for this and prevent it?

  - by user328960

  Problem and about the database: Data from a record in Access 2003 database has disappeared. This database has 1 backend and 3 frontends, multiple users and is hosted on Citrix. Within this database, we have records of all clients served, ranging in the 1000s. Background info: The form for client data entry is set up with various subforms, including both a "programs enrolled" subform and a "services" subform. A client can be enrolled in multiple programs. Once enrolled in a program, services can be entered for that program area using the services subform. There are multiple fields in the services subform, one of which is a drop-down field allowing you to choose from the programs a client has been enrolled in (the list is updated for that client whenever he is enrolled in a new program). The problem details: For one specific record and one specific program area, the program has disappeared from the "programs enrolled" subform and all of the related services have disappeared from the "services" subform for a period of 3 months of data entry. However, other programs and services for this record did not disappear. Questions: Is the disappearance of data a common Access 2003 problem? Are there tests in place that can be run to see if data is disappearing and catch that data? If so, what are they? If there is specific code involved, what is it? What can be done to prevent the disappearing of data (other than using a different database)?

  Read the article

• MS-Access: What could cause one form with a join query to load right and another not?

  - by Daniel Straight

  Form1 Form1 is bound to Table1. Table1 has an ID field. Form2 Form2 is bound to Table2 joined to Table1 on Table2.Table1_ID=Table1.ID Here is the SQL (generated by Access): SELECT Table2.*, Table1.[FirstFieldINeed], Table1.[SecondFieldINeed], Table1.[ThirdFieldINeed] FROM Table1 INNER JOIN Table2 ON Table1.ID = Table2.[Table1_ID]; Form2 is opened with this code in Form1: DoCmd.RunCommand acCmdSaveRecord DoCmd.OpenForm "Form2", , , , acFormAdd, , Me.[ID] DoCmd.Close acForm, "Form1", acSaveYes And when loaded runs: Me.[Table1_ID] = Me.OpenArgs When Form2 is loaded, fields bound to columns from Table1 show up correctly. Form3 Form3 is bound to Table3 joined to Table2 on Table3.Table2_ID=Table2.ID Here is the SQL (generated by Access): SELECT Table3.*, Table2.[FirstFieldINeed], Table2.[SecondFieldINeed] FROM Table2 INNER JOIN Table3 ON Table2.ID = Table3.[Table2_ID]; Form3 is opened with this code in Form2: DoCmd.RunCommand acCmdSaveRecord DoCmd.OpenForm "Form3", , , , acFormAdd, , Me.[ID] DoCmd.Close acForm, "Form2", acSaveYes And when loaded runs: Me.[Table2_ID] = Me.OpenArgs When Form3 is loaded, fields bound to columns from Table2 do not show up correctly. WHY? UPDATES I tried making the join query into a separate query and using that as my record source, but it made no difference at all. If I go to the query for Form3 and view it in datasheet view, I can see that the information that should be pulled into the form is there. It just isn't showing up on the form.

  Read the article

• MS Access: Why is ADODB.Recordset.BatchUpdate so much slower than Application.ImportXML?

  - by apenwarr

  I'm trying to run the code below to insert a whole lot of records (from a file with a weird file format) into my Access 2003 database from VBA. After many, many experiments, this code is the fastest I've been able to come up with: it does 10000 records in about 15 seconds on my machine. At least 14.5 of those seconds (ie. almost all the time) is in the single call to UpdateBatch. I've read elsewhere that the JET engine doesn't support UpdateBatch. So maybe there's a better way to do it. Now, I would just think the JET engine is plain slow, but that can't be it. After generating the 'testy' table with the code below, I right clicked it, picked Export, and saved it as XML. Then I right clicked, picked Import, and reloaded the XML. Total time to import the XML file? Less than one second, ie. at least 15x faster. Surely there's an efficient way to insert data into Access that doesn't require writing a temp file? Sub TestBatchUpdate() CurrentDb.Execute "create table testy (x int, y int)" Dim rs As New ADODB.Recordset rs.CursorLocation = adUseServer rs.Open "testy", CurrentProject.AccessConnection, _ adOpenStatic, adLockBatchOptimistic, adCmdTableDirect Dim n, v n = Array(0, 1) v = Array(50, 55) Debug.Print "starting loop", Time For i = 1 To 10000 rs.AddNew n, v Next i Debug.Print "done loop", Time rs.UpdateBatch Debug.Print "done update", Time CurrentDb.Execute "drop table testy" End Sub I would be willing to resort to C/C++ if there's some API that would let me do fast inserts that way. But I can't seem to find it. It can't be that Application.ImportXML is using undocumented APIs, can it?

  Read the article

• How should I lock the table in this VB6 / Access application?

  - by Brian Hooper

  I'm working on a VB6 application using an Access database. The application writes messages to a log table from time to time. Several instances of the application may be running simultaneously and to distinguish them they each have their own run number. The run number is deduced from the log table thus... Set record_set = New ADODB.Recordset query_string = "SELECT MAX(RUN_NUMBER) + 1 AS NEW_RUN_NUMBER FROM ERROR_LOG" record_set.CursorLocation = adUseClient record_set.Open query_string, database_connection, adOpenStatic, , adCmdText record_set.MoveLast If IsNull(record_set.Fields("NEW_RUN_NUMBER")) Then run_number = 0 Else run_number = record_set.Fields("NEW_RUN_NUMBER") End If command_string = "INSERT INTO ERROR_LOG (RUN_NUMBER, SEVERITY, MESSAGE) " & _ " VALUES (" & Str$(run_number) & ", " & _ " " & Str$(SEVERITY_INFORMATION) & ", " & _ " 'Run Started'); " database_connection.Execute command_string Obviously there is a small gap between the calculation of the run number and the appearance of the new row in the database, and to prevent another instance getting access between the two operations I'd like to lock the table; something along the lines of SET TRANSACTION READ WRITE RESERVING ERROR_LOG FOR PROTECTED WRITE; How should I go about doing this? Would locking the recordset do any good (the row in the record set doesn't match any particular row in the database)?

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >