Search Results

Search found 1425 results on 57 pages for 'cisco catalyst'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 14/57 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

  • SSH login to Cisco switch using Rancid times out

    - by Lars
    I have a 3560 switch that I have configured to accept SSH logins, and this works fine. However I cannot get Rancid to complete the login process to any of my switches using SSH. I get a timeout error after a minute or so. Telnet logins work fine with the same username and password. Here is my rancid setup in .cloginrc: add user * {myuser} add password * {strongAccessPassword} {strongEnablePassword} add method * ssh telnet Then, when I run bin/clogin 10.10.1.10 I get: # bin/clogin 10.10.1.10 10.10.1.10 spawn ssh -c 3des -x -l myuser 10.10.1.10 ############################################### Please authenticate. ############################################### Password: Error: TIMEOUT reached Again, when I do this using telnet as my preferred mothod in .cloginrc, it works without issue.

    Read the article

  • static routes, cisco ASA, remote locations

    - by Jeff
    192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

    Read the article

  • Cisco Pix does not let traffic pass from outside to inside even though ACL permits

    - by Rickard
    I have tried to make my pix 515 allow traffic from outisde interface to inside, but despite permitting ACL's, it doesn't seem to let traffic through. (It is letting traffic out as it should though) I am have tried both of the following: access-list acl_in extended permit tcp any host 10.131.73.2 eq www and access-list acl_in extended permit ip any any None of them help, but I can access 10.131.73.2 from any host on the inside network. This is a one single host on the inside that should every now and then have an HTTP server running for development purpouses, so it doesn't need to reside on DMZ (and as far as I know, I can't place it on DMZ either as it's in the same subnet as the other ip's I have. Could I have missed anything? I am using PIX Version 8.0(4) My current running config looks like this: http://pastebin.com/TvRFyDrF Hope someone can help me get this working.

    Read the article

  • Cisco router not receiving OSPF updates

    - by WebDevHobo
    Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

    Read the article

  • Cisco 1841: Multi-wan capable?

    - by gravyface
    Have an 1841 router with the following interfaces: 0/0 0/1 AUX on the right side, believe it's slot 1, there's an add-on interface FE0 (shows up as 000). Does this allow a multi-WAN configuration? i.e. can I use 0/1 for WAN1 and FE0 as WAN2 out-of-the-box or does this require additional licensing and/or another add-on interface in slot 0?

    Read the article

  • Cisco ASA 5505 and slow download speeds for Apple devices

    - by James
    For traffic routing through my ASA 5505, downloads for all Apple devices, including AppleTV iPad gen 1 IMac MacBook Pro are very slow. speedof.me show less than 1 Mbps download (where I should have 20 Mbps +), yet for any Windows-based device, the download speeds are in excess of 20 Mbps. The Windows device, including the iMac and MacBook Pro machines, are connected via ethernet cable. Why are Apple devices experiencing such pain? Is it an ASA setting, or something else? Thanks.

    Read the article

  • Is span monitoring on Cisco ASA 5520 possible?

    - by Brent
    From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

    Read the article

  • how can I reconnect DSL in cisco router 877w

    - by Sulaiman
    Hi All, I've configured ADSL and added a new public LAN ips for the router. How can I reconnect DSL connection and apply the new configuration without executing the command reload this is the commands I am using for DSL configuration config terminal interface dialer 0 ppp chap hostname User ppp chap password 0 Pass exit exit wr mem and this is the commands I am using for adding IP addresses: configure t interface vlan 1 ip address xx.xx.xx.xx 255.255.255.252 Secondary exit wr mem thank you

    Read the article

  • Block Skype on Cisco IOS

    - by ensnare
    I'm trying to block skype via policy routing but it's not working ... here's my configuration: class-map match-any block match protocol skype policy-map QoS-Priority-Input class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop policy-map QoS-Priority-Output class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop interface FastEthernet4 description WAN service-policy input QoS-Priority-Input service-policy output QoS-Priority-Output

    Read the article

  • Cisco ASA 5510 shortage?

    - by PHLiGHT
    Has anyone else had problems ordering them recently? Our main vendors have had them out of stock for awhile now and we need to buy a couple. Any known places where they are in stock or why the shortage?

    Read the article

  • Filtering in Cisco Unified Communications Manager using AXL programming

    - by Santhosha Kaldambe
    Hi, I want to implement a Application which gets values from CUCM resource. I am currently using the AXL snippet <firstname>FirstNameFilter</firstname><lastname>LastNameFilter</lastname> This will work as & between two filters. for example my filter is FirstNameFilter = sam* LastNameFilter = joy* this will return the entries which satisfies both the filters. But i want to filter in such a way that we need to or this filter like i need to get the users with First Name is sam* or last name = joy*. Whether anyone did such AXL programming? It will be very helpful if i get the answer for this! Thanks Santhosh

    Read the article

  • Cisco Nexus 5000 Vs. UCS 6100

    - by radius
    Hello, I'm a bit lost when I take a look to Nexus 5000 and UCS 6100. The description of Nexus 5000 is quite clear and I see what it does but the description of the UCS 6100 is a bit unclear for me. Could someone told me what would be the difference between a Nexus 5000 with all port at 10G and an UCS 6100 with all port at 10G ? Thanks,

    Read the article

  • Cisco IOS ACL types

    - by cjavapro
    The built in command help list displays access list types based on which range. router1(config)#access-list ? <1-99> IP standard access list <100-199> IP extended access list <1100-1199> Extended 48-bit MAC address access list <1300-1999> IP standard access list (expanded range) <200-299> Protocol type-code access list <2000-2699> IP extended access list (expanded range) <700-799> 48-bit MAC address access list dynamic-extended Extend the dynamic ACL absolute timer rate-limit Simple rate-limit specific access list router1(config)# What are each of the types? Can multiple types of ACLs be applied to a given interface?

    Read the article

  • Cisco ASA 8.2 ACL For NAT

    - by javano
    Sadly I have gone back in time to ASA 8.2(5)33 which I am not so familiar with. I have configured NAT between two interfaces but traffic isn't passing becasue I can't get the ACL to work; (The full config which isn't very big is here but to keep this post tidy I have just pasted the important parts below); interface Ethernet0/0 switchport access vlan 108 ! interface Ethernet0/6 switchport access vlan 104 ! interface Ethernet0/7 switchport access vlan 105 ! interface Vlan104 description BUILDING2 nameif BUILDING2 security-level 0 ip address 10.104.0.1 255.255.255.0 ! interface Vlan105 description BUILDING1 nameif BUILDING1 security-level 0 ip address 10.105.0.1 255.255.255.0 ! interface Vlan108 description Main LAN VLAN nameif lan security-level 0 ip address 172.22.0.215 255.255.255.0 ! object-group network obj_net_Remote_Hosts network-object host 111.111.111.3 network-object host 111.111.111.65 object-group network obj_host_pc1_eth1 network-object host 10.104.0.111 object-group network obj_host_pc2_eth1 network-object host 10.104.0.112 object-group network obj_host_pc3_eth1 network-object host 10.104.0.106 object-group network obj_host_pc4_eth1 network-object host 10.104.0.107 object-group network obj_net_PCs description IPs of PCs group-object obj_host_pc1_eth1 group-object obj_host_pc2_eth1 group-object obj_host_pc3_eth1 group-object obj_host_pc4_eth1 access-list acl_NAT_pc1_91 extended permit tcp host 10.104.0.111 host 111.111.111.3 eq 8101 access-list acl_Permit_PCs extended permit tcp object-group obj_net_PCs object-group obj_net_Remote_Hosts eq 8101 ! global (BUILDING1) 11 111.111.222.91 netmask 255.255.255.255 nat (BUILDING2) 11 access-list acl_NAT_pc1_91 access-group acl_Permit_PCs in interface BUILDING2 route BUILDING1 111.111.111.3 255.255.255.255 10.105.0.2 1 route BUILDING1 111.111.111.65 255.255.255.255 10.105.0.2 1 When I try and connect from PC1 to ip 111.111.111.3 I see the following error logged on the ASA console; %ASA-2-106001: Inbound TCP connection denied from 10.104.0.111/38495 to 111.111.111.3/8101 flags SYN on interface blades What the duce!

    Read the article

  • Pasting extended ACL contents into telnet session to Cisco Router SIM

    - by Kyle Brandt
    I have a telnet session to a dynamips router sim. When I try to paste the contents of an actually working ACL retrieved from 'show run' into the access list, only part of gets pasted. The session is something like: enable conf t ip access-list extended Internet <PASTE of Rules> It stops right in the middle of a line: permit tcp any host 123.123.123.123 gt 1 ! should be gt 1023 Anyone know what is happening? The source is an extended access list.

    Read the article

  • how do i enable ftp on a cisco NAC 3310

    - by kyoung
    I'm trying to ftp updates to it, but i can't seem to find where the .conf is that deals with ftp so i can enable/configure it when i attempt to connect to the NAC from my desktop via winSCP (using ftp) i get an error saying the connection is being actively refused.

    Read the article

  • Cisco T1 Routing Help

    - by Joseph
    Thanks to someone on this site I was able to get the Serial0/0 interface up. I now have: DCD=up DSR=up DTR=up RTS=up CTS=up My next challenge seems to be in the routing and/or PC ip setup. This are the pertinent details from L3: WAN Network: 6.59.186.60/30 Level3 Side: 6.59.186.61 Customer Side: 6.59.186.62 Cust. LAN IPs: 6.59.192.224/27 What would be the IOS commands to setup this route correctly? Am I correct that I would the choose an IP like 6.59.192.224, subnet 255.0.0.0, gateway 6.59.186.62? Thanks

    Read the article

  • Cisco Switching Module and HSRP interface Tracking

    - by Kyle Brandt
    When using 4 port switching module where each port is configured to switchport access vlan ##, for HRSP should I track the vlan interface or the FastEthernet interface? interface FastEthernet0/0/0 switchport access vlan 10 interface Vlan10 ip address 12.12.12.1 255.255.255.0 int FastEthernet0/1 ip address 192.168.1.2 255.255.255.0 standyby ip 192.168.128.1 standby track ?? ! FastEthernet 0/0/0 or Vlan 10?

    Read the article

  • Cisco ASA 5505 (8.05): asymmetrical group-policy filter on an L2L IPSec tunnel

    - by gravyface
    I'm trying to find a way to setup a bi-directional L2L IPSec tunnel, but with differing group-policy filter ACLs for both sides. I have the following filter ACL setup, applied, and working on my tunnel-group: access-list ACME_FILTER extended permit tcp host 10.0.0.254 host 192.168.0.20 eq 22 access-list ACME_FILTER extended permit icmp host 10.0.0.254 host 192.168.0.20 According to the docs, VPN filters are bi-directional, you always specify the remote host first (10.0.0.254), followed by the local host and (optionally) port number, as per the documentation. However, I do not want the remote host to be able to access my local host's TCP port 22 (SSH) because there's no requirement to do so -- there's only a requirement for my host to access the remote host's SFTP server, not vice-versa. But since these filter ACLs are bidirectional, line 1 is also permitting the remote host to access my host's SSH Server. The documentation I'm reading doesn't seem to clear to me if this is possible; help/clarification much appreciated.

    Read the article

  • Cisco: unable to negotiate IP using IPCP with Windows server

    - by lnk
    I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

    Read the article

  • Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

    - by Jander
    I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

    Read the article

  • Cisco Access switch is dropping large amount of end points

    - by user135458
    This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >