Search Results

Search found 1425 results on 57 pages for 'cisco catalyst'.

Page 15/57 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• Cisco ASA - NAT'ing VPN traffic

  - by DrStalker

  I have an IPsec VPN setup like this: [Remote users]-[Remote ASA] <-VPN-> [My ASA]-[Subnet A]-[Router 2]-[Subnet B] The VPN is set to handle traffic between [remote users] and [Subnet A]; it does not include [Subnet B]. Pretend the firewall rules for all routers are to permit everything. Now I want to redirect traffic that comes over the VPN to a specific IP on [subnet A] (192.168.1.102) to an IP on [Subnet B] (10.1.1.133) If I add a rule on [My ASA] to NAT traffic to original IP 192.168.1.102 to new IP 10.1.1.133, 1) Will this affect the connections coming in over the VPN? (ie: the VPN packets are unencrypted and then NAT is applied) 2) Will this work when the post-NAT target is on Subnet-B, which is not part of the VPN traffic selection?

  Read the article

• Cisco NAT vs Bridge vs BVI

  - by cjavapro

  The only devices on this particular LAN will all have public IP addresses. Also the public IP address will be configured directly on the machine,,, so we will not translate private/public IP addresses. If we use NAT,, we would have to translate the public IP on the WAN to the public IP on the LAN. The only security feature I expect on the gateway is an access list. I don't really know much about networking, so I am sorry if this question is generic.

  Read the article

• Cisco ASA 5505 inside interface multiple ip addresses

  - by Oneiroi

  I have an issue this morning where I want to be able to assign multiple ip addresses to the inside interface to facilitate an ip range migration for an office. Namely from a 192.168.1.x range to the new range, with the minimum of interruption for those working in the office. (New DHCP leases will use the new range, whilst those still on the 192.168.1.x range can continue to work until their lease is renewed). However I can not for the life of me figure out how to achieve this, trying to create multiple interfaces for the job leads to complaints about the license only allowing 2 active interfaces. Any suggestions? thanks in advance.

  Read the article

• cisco 2851 router: can't view switch ports

  - by red888

  I want to setup vlans on a 2851, but I'm not sure how to access the switch ports. I can access or view them. Is there something I have to enable? I have some devices plugged into the switch ports and they are communicating with each other fine. router(config)#do show ip int bri Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0 unassigned YES NVRAM administratively down down GigabitEthernet0/1 unassigned YES NVRAM administratively down down GigabitEthernet1/0 10.1.1.1 YES manual up up

  Read the article

• Alternate Client for Cisco Unified Personal Communicator protocol

  - by Jason M

  At work we have an in-house chat system using CUPC. Does anyone else out there use this? There are a few things I do not like about this client: Where's the chat log? If I close the window, I have no way of getting my conversation back. Tabbed interface? That would be nice. I hate having multiple chat windows up, having to arrange them around my desktop as more people start talking to me. I don't like that I have to use this one-off application for particular this protocol when other chat clients will handle 99% of the other protocols I use. Tell me: Is the protocol an open standard for which other applications have support? (pidgin, adium, digsby, etc.) If not, can I overcome these issues from within CUPC? Perhaps there are newer versions of the client that overcome these issues.

  Read the article

• EasyVPN client Access mutiple subnet behind cisco 5510

  - by zatrac

  I need help with the following scenario Main network ASA 5510 (one inside 192.168.10.1 connection and one outside connection). This ASA 5510 connect to switch 3570 with 3 VLANS configured (192.168.10.0, 10.10.11.0, 10.10.12.0). On the remote site I have ASA5505 ( 10.10.13.0) connected to this ASA5510 through EZVPN, but all it can see is the 192.168.10.0 subnet. What do I need to do to get the subnet 10.10.13.0 to see all 3 internal subnets.

  Read the article

• cisco asa query dns external

  - by Alpacino

  my lab network asa firewall below 10.10.10.20 -- ASA --- 192.168.1.10 -- website external my client 10.10.10.20 want to access website external and i create nat nat (inside,outside) static 192.168.1.10 and access list access-list outside-acl extended permit tcp any host 10.10.10.20 eq www access-list outside-acl extended permit tcp any host 10.10.10.20 eq domain access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq www access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq domain access-group outside-acl in interface outside access-group inside-acl in interface inside when i access to website with domain name it can't access but i access website with ip address it work please help me to solve problem thank you

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Cisco 1760 T1 Setup

  - by Joseph

  My 1760 has a WIC1-T1 card in Slot 0 and the slot 0 "OK" light is lit. When the router boots it shows that it sees the T1 card. I would like to configure my T1. I received the following details from my ISP: * Removed IP's IP Version: IPv4 Router Interface: edge1.mia1 -- t1-2/1/0:2:13 -- Switch Port: Vlan: WAN Network: 4.59.?.?/30 Level3 Side: 4.59.?.? Customer Side: 4.59.?.? Cust. LAN IPs: 4.59.?.?/27 The problem is that it is not listed under interfaces. I am a noob with IOS, please let me know if you need more details. Thanks.

  Read the article

• Cisco Unifies Communications Manager 7.0 - Installing Extension Mobility

  - by Lance

  I've setup extension mobility to the best of my ability, however, it its perplexing me... From the materials I've been reading I have established I need to have the following URL in place: http://IP/emapp/EmAppServlet?device=#DEVICENAME# If I try and browse to this in a web browser I can a blankHTML page. When my registered phone (CIPC) presses Services - Extension Mobility, it just sits there / delivers a blank page. I figure this isn't coincidence... Any ideas?

  Read the article

• Cisco FWSM -> ASA upgrade broke our mail server

  - by Mike Pennington

  We send mail with unicode asian characters to our mail server on the other side of our WAN... immediately after upgrading from a FWSM running 2.3(2) to an ASA5550 running 8.2(5), we saw failures on mail jobs that contained unicode. The symptoms are pretty clear... using the ASA's packet capture utility, we snagged the traffic before and after it left the ASA... access-list PCAP line 1 extended permit tcp any host 192.0.2.25 eq 25 capture pcap_inside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface inside capture pcap_outside type raw-data access-list PCAP buffer 1500000 packet-length 9216 interface WAN I downloaded the pcaps from the ASA by going to https://<fw_addr>/pcap_inside/pcap and https://<fw_addr>/pcap_outside/pcap... when I looked at them with Wireshark Follow TCP Stream, the inside traffic going into the ASA looks like this EHLO metabike AUTH LOGIN YzFwbUlciXNlck== cZUplCVyXzRw But the same mail leaving the ASA on the outside interface looks like this... EHLO metabike AUTH LOGIN YzFwbUlciXNlck== XXXXXXXXXXXX The XXXX characters are concerning... I fixed the issue by disabling ESMTP inspection: wan-fw1(config)# policy-map global_policy wan-fw1(config-pmap)# class inspection_default wan-fw1(config-pmap-c)# no inspect esmtp wan-fw1(config-pmap-c)# end The $5 question... our old FWSM used SMTP fixup without issues... mail went down at the exact moment that we brought the new ASAs online... what specifically is different about the ASA that it is now breaking this mail? Note: usernames / passwords / app names were changed... don't bother trying to Base64-decode this text.

  Read the article

• Cisco ASA 5505 network route for static IP hosts

  - by TheCapn

  I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

  Read the article

• VPN between Cisco ASA 5505 AND Sonicwall SOHO3

  - by user41451

  Hello. I am trying to establish a site-to-site VPN tunnel between an old SOHO3 and an ASA 5505. The ASA has a static IP and the SOHO3 is dynamic. I have tried everything my limited knowledge lets me and need some advice on how to proceed! Phase 1 (according to the ASA logs) completes - followed by a message saying "All IPSec SA proposals found unacceptable!" so I guess the settings between the two don't match. I have played with various combinations and nothing seems to work - I am overlooking something, just not sure what it is! Any help would be appreciated.

  Read the article

• Per Sender Traffic Limit on Cisco 6500

  - by user71557

  Hi All, I have a 6509 with ~1000 user machines in different vlans, I want to allow 10 server machines to send as much as they can/want but to limit all client machines from all subnets to have a sedning rate limit of 1mbps with no receiving limitation. It is worth noting that all my ip addresses are assigned using a DCHP server and there are 1000 of them so I can not write ACLs for every address seperately. Can any one provide some kind of help please?

  Read the article

• Can I use Catalyst to display images or graphs?

  - by Octopus

  I have simple Perl/CGI scripts based web server which is mainly used to display graphs and images. I am looking to make it more technical and come to know about Catalyst. I have installed all the required Perl modules on my test platform and created an application called myweb. Also, I am going through the Catalyst documents to reach my goal but nothing helpful yet. Is Catalyst helpful to display images/graphs on web? How can I use my existing CGI/Perl scritps with Catalyst? Any example would be really appreciated.

  Read the article

• PARTNER WEBCAST : Nimble SmartStack for Oracle with Cisco UCS (Nov 12)

  - by Zeynep Koch

  You are invited to the live webcast with Nimble Storage, Oracle and Cisco where we will talk about the new SmartStack solution from Nimble Storage that features Oracle Linux, Oracle VM and Cisco UCS products. When : Tuesday, November 12, 2013, 11:00 AM Pacific Time Panelists: Michele Resta, Director of Linux and Virtualization Alliances, Oracle John McAbel, Senior Product Manager, Cisco Ibby Rahmani, Solutions Marketing, Nimble Storage SmartStack™solutions provide pre-validated reference architectures that speed deployments and minimize risk. All SmartStack solutions incorporate Cisco UCS as the compute and network infrastructure. In this webinar, you will learn how Nimble Storage SmartStack with Oracle and Cisco provides a converged infrastructure for Oracle Database environments with Oracle Linux and Oracle VM. SmartStack, built on best-of-breed components, delivers the performance and reliability needed for deploying Oracle on a single symmetric multiprocessing (SMP) server or Oracle Real Application Clusters (RAC) on multiple nodes.  Register today 

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• Running HTTP and HTTPS connections for a single domain (say, www.example.com) through a Cisco ACE SS

  - by Paddu

  My web application config has a Cisco ACE load balancing across a server farm and I want to use the ACE as an SSL endpoint as well. To make this work, the network architect has come up with a design where all secure pages have to be served from secure.my-domain.com, while non-secure pages are served up from www.my-domain.com. The reason for this is apparently that the configuring the Cisco ACE to accept HTTPS requests on port 443 for a particular public IP prevents the simultaneous acceptance of HTTP requests on port 80 for the same IP. While I'm not a networking (or Cisco) expert, this seems to be intuitively wrong, as it would prevent any website using the Cisco ACE to serve pages on http://www.my-domain.com and https://www.my-domain.com simultaneously. In this situation, my questions are: Is this truly a limitation of the Cisco ACE when used as an SSL endpoint? If not, then can I assume that we can set up the ACE to accept connections for a particular IP on ports 80 and 443, and function as an SSL endpoint for the incoming requests on 443? Links to appropriate documentation most welcome here. Assuming the setup in the previous question, can I then redirect both sets of requests to the same server farm on the same port?

  Read the article

• Cisco ASA user authentication options - OpenID, public RSA sig, others?

  - by Ryan

  My organization has a Cisco ASA 5510 which I have made act as a firewall/gateway for one of our offices. Most resources a remote user would come looking for exist inside. I've implemented the usual deal - basic inside networks with outbound NAT, one primary outside interface with some secondary public IPs in the PAT pool for public-facing services, a couple site-to-site IPSec links to other branches, etc. - and I'm working now on VPN. I have the WebVPN (clientless SSL VPN) working and even traversing the site-to-site links. At the moment I'm leaving a legacy OpenVPN AS in place for thick client VPN. What I would like to do is standardize on an authentication method for all VPN then switch to the Cisco's IPSec thick VPN server. I'm trying to figure out what's really possible for authentication for these VPN users (thick client and clientless). My organization uses Google Apps and we already use dotnetopenauth to authenticate users for a couple internal services. I'd like to be able to do the same thing for thin and thick VPN. Alternatively a signature-based solution using RSA public keypairs (ssh-keygen type) would be useful to identify user@hardware. I'm trying to get away from legacy username/password auth especially if it's internal to the Cisco (just another password set to manage and for users to forget). I know I can map against an existing LDAP server but we have LDAP accounts created for only about 10% of the user base (mostly developers for Linux shell access). I guess what I'm looking for is a piece of middleware which appears to the Cisco as an LDAP server but will interface with the user's existing OpenID identity. Nothing I've seen in the Cisco suggests it can do this natively. But RSA public keys would be a runner-up, and much much better than standalone or even LDAP auth. What's really practical here?

  Read the article

• Is it possible to run two VPN clients at the same time?

  - by Manuel Selva

  I would like to run two VPN clients at the same time: one Cisco client and one VPNC client. For now I have my VPNC client configured to route only some known IPs to the VNC interface and would like to add the same thing for the Cisco client at the same time. Is it possible ? Do I need a Cisco client to connect to a Cisco server or can I use an other client such as VPNc ? I installed the cisco one because it was the one suggested but I am wondering if this is mandatory ? I guess the answer may be yes, and off course I am interested in "required configurations" to do that

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• Example Code for Cisco Digital Media Player or TVzilla

  - by user338844

  I have a Cisco Digital Media Player and I need to create a web page using the DMP (Digital Media Player) Javascript Libraries, the problem is I don't know anything about them. I have lots of documentation, however I am hoping to find some example code already out there. Does anyone know of anything like that?

  Read the article

• Cisco pix command - whats this command mean?

  - by jason clark

  Hi, Anyone know what the following means? I have these two lines in our cisco PIX configuration file but have no references to these IP's anywhere else in the config and cant find a device on the network with them. global (inet) 10 213.228.xxx.xx global (inet) 20 213.228.xxx.xx thanks, Jason (BTW: I've xxx'ed out the remainder of the ip for security :-0 )

  Read the article

• Speed Problem with Wireless Connectivity on Cisco 877w

  - by Carl Crawley

  Having a bit of a weird one with my local LAN setup. I recently installed a Cisco 877W router on my DSL2+ connection and all is working really well.. Upgraded the IOS to 12.4 and my wired clients are streaming connectivity superfast at 1.3mb/s. However, there seems to be an issue with my wireless clients - I can't seem to stream any data across the local wireless connection (LAN) and using the Internet, whilst responsive enough isn't really comparable with the wired connection speed. For example, all devices are connected to an 8 Port Gb switch on FE0 from the Router with a NAS disk and on my wired clients, I can transfer/stream etc absolutely fine - however, transferring a local 700Mb file on my local LAN estimates 7-8 hours to transfer :( The Wireless config is as follows : interface Dot11Radio0 description WIRELESS INTERFACE no ip address ! encryption mode ciphers tkip ! ssid [MySSID] ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 channel 2462 station-role root rts threshold 2312 world-mode dot11d country GB indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding All devices are connected to the Gb Switch which is connected to FE0 with the following: Hardware is Fast Ethernet, address is 0021.a03e.6519 (bia 0021.a03e.6519) Description: Uplink to Switch MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 19 packets/sec 5 minute output rate 167000 bits/sec, 23 packets/sec 177365 packets input, 52089562 bytes, 0 no buffer Received 919 broadcasts, 0 runts, 0 giants, 0 throttles 260 input errors, 260 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 156673 packets output, 106218222 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Not sure why I'm having problems on the wireless and I've reached the end of my Cisco knowledge... Thanks for any pointers! Carl

  Read the article

• Ubuntu 13.10 AMD/ATI proprietary driver slow boot time, black screen after logging in and lengthy login/logout delays

  - by NahsiN

  Ubuntu 13.10 is causing me major headaches with my AMD/ATI HD 5770 GPU. Below is a list of problems I am currently encountering. 1) The boot time is extended by at least 25s after installing catalyst 13.4. Using open source radeon drivers, my boot time till the login screen is ~10s. With catalyst 13.4 installed, the boot time increases to ~35s. This was not the case in Ubuntu 13.04, 12.10 or 12.04. I have done the driver installation manually (instructions from wiki.cchtml.com) and using software center and there is no difference. I have not tried the catalyst 13.8 beta driver. 2) After manual installation of catalyst 13.4, I get stuck at a black screen after logging in. I have to purge fglrx to resolve the problem. I tried sudo amdconfig --initial -f but it didn't help. 3) The delay between logging in and unity being displayed is ~10-15s for BOTH open source and proprietary drivers. During the delay, it's just a black screen. Whenever I logout, there is again a ~10-15s delay with the login screen appearing stuck before lightdm allows me to enter my password again. This is ridiculous! Yes, I could stick with open source radeon drivers but I would like to install Steam and play my Valve collection on the machine. Is anybody else encountering similar issues?

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >