Search Results

Search found 4885 results on 196 pages for 'delivery failure'.

Page 14/196 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• boot issues - long delay, then "gave up waiting for root device"

  - by chazomaticus

  I've had this issue on and off for about two years now. I noticed it on a new (custom built) machine running 10.04 when that first came out, but then it went away until a few months ago. I've gone through a number of hard drive changes but I can't say specifically what if anything I changed hardware-wise to make it stop or start happening. I had assumed upgrading to a modern Ubuntu version would fix the issue, so I installed 12.04 beta on a spare partition last night, but it's still happening. Here's the issue. After grub loads and I select a kernel to boot, the screen goes blank save for a blinking cursor. It sits in this state for many long minutes before it finally gives up and gives me an initramfs shell with the message gave up waiting for root device (and lists the /dev/disk/by-uuid/... path it was waiting for) but no other specific diagnostic information. Now, here's the tricky part. For one, the problem is intermittent - sometimes it progresses from the blinking cursor to the Ubuntu splash boot screen in a few seconds, and once it gets that far it always continues booting fine. The really bizarre thing is that I can "force" it to "find" the root device by repeatedly pressing the space bar and hitting the machine's power button. If I tap those enough, eventually I will notice the hard drive light coming on, at which point it will always continue the boot process after a few seconds. Interestingly, if I wait slightly too long before pressing the power button (30s?), as soon as I press it I get the gave up waiting message and the initramfs shell. I've tried setting up /etc/fstab (and the grub menu.lst or whatever it's called nowadays) to use device names (e.g. /dev/sda1) instead of UUIDs, but I get the same effect just with the device name, not UUID, in the error message. I should also mention that when I boot to Windows 7, there is no issue. It boots slowly all the time just by virtue of being Windows, but it never hangs indefinitely. This would seem to indicate it's a problem in Ubuntu, not the hardware. It's pretty annoying to have to babysit the computer every time it boots. Any ideas? I'm at a loss. Not even sure how to diagnose the issue. Thanks! EDIT: Here's some dmesg output from 10.04. The 15 second gap is where it was doing nothing. I pressed the power button and space bar a few times, and the stuff at 16 seconds happened. Not sure what any of it means. [ 1.320250] scsi18 : ahci [ 1.320294] scsi19 : ahci [ 1.320320] ata19: SATA max UDMA/133 abar m8192@0xfd4fe000 port 0xfd4fe100 ir q 18 [ 1.320323] ata20: SATA max UDMA/133 abar m8192@0xfd4fe000 port 0xfd4fe180 ir q 18 [ 1.403886] usb 2-4: new high speed USB device using ehci_hcd and address 4 [ 1.562558] usb 2-4: configuration #1 chosen from 1 choice [ 16.477824] ata16: SATA link down (SStatus 0 SControl 300) [ 16.477843] ata19: SATA link down (SStatus 0 SControl 300) [ 16.477857] ata3: SATA link down (SStatus 0 SControl 300) [ 16.477895] ata15: SATA link down (SStatus 0 SControl 300) [ 16.477906] ata20: SATA link down (SStatus 0 SControl 300) [ 16.477977] ata17: SATA link down (SStatus 0 SControl 300) [ 16.478003] ata12: SATA link down (SStatus 0 SControl 300) [ 16.478046] ata13: SATA link down (SStatus 0 SControl 300) [ 16.478063] ata14: SATA link down (SStatus 0 SControl 300) [ 16.478108] ata11: SATA link down (SStatus 0 SControl 300) [ 16.478123] ata18: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 16.478127] ata6: SATA link down (SStatus 0 SControl 300) [ 16.478157] ata5: SATA link down (SStatus 0 SControl 300) [ 16.478193] ata18.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66 After that, it took its sweet time, and I had to keep hitting space bar to coax it along. Here's some more dmesg output from a little later in the boot process: [ 17.982291] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00 :13.0/usb5/5-2/5-2:1.0/input/input4 [ 17.982335] generic-usb 0003:046E:5506.0002: input,hidraw1: USB HID v1.10 Key board [BTC USB Multimedia Keyboard] on usb-0000:00:13.0-2/input0 [ 18.005211] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00 :13.0/usb5/5-2/5-2:1.1/input/input5 [ 18.005274] generic-usb 0003:046E:5506.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:13.0-2/input1 [ 22.484906] EXT4-fs (sda6): INFO: recovery required on readonly filesystem [ 22.484910] EXT4-fs (sda6): write access will be enabled during recovery [ 22.548542] EXT4-fs (sda6): recovery complete [ 22.549074] EXT4-fs (sda6): mounted filesystem with ordered data mode [ 32.516772] Adding 20482832k swap on /dev/sda5. Priority:-1 extents:1 across:20482832k [ 32.742540] udev: starting version 151 [ 33.002004] Bluetooth: Atheros AR30xx firmware driver ver 1.0 [ 33.008135] parport_pc 00:09: reported by Plug and Play ACPI [ 33.008186] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 33.012076] lp: driver loaded but no devices found [ 33.037271] ppdev: user-space parallel port driver [ 33.090256] lp0: using parport0 (interrupt-driven). Any clues in there?

  Read the article

• Repairing or recreating a bootloader on a multi-booting EFI GPT system

  - by Emre

  Reinstalling Ubuntu messed up my boot loader so I I tried to fix it with boot repair. It detected my OSX installation and asked about removing the "separate boot/EFI". It also said my partition was full despite the fact that it wasn't and asked me to remove stuff. I declined both and proceeded. It's been stuck at the "purge and reinstall the GRUB" stage for half an hour. Is this typical, bearing in mind I have a fast SSD and CPU? Is there a better way to re-install grub on a multi-booting UEFI system? Does my pastebin provide any insight?

  Read the article

• Kernel panic on reboot after failed logical volume resize

  - by Derek

  I attempted to do a logical volume resize yesterday using the follwoing commands $sudo pvdisplay "/dev/sda8" is a new physical volume of "113.11 GiB" --- NEW Physical volume --- PV Name /dev/sda8 VG Name PV Size 113.11 GiB Allocatable NO PE Size 0 Total PE 0 Free PE 0 Allocated PE 0 PV UUID jwyO1o-b2ap-CW51-kx7O-kf26-arim-SM8V6m $sudo vgextend vg /dev/sda8 sudo vgdisplay vg --- Volume group --- VG Name vg System ID Format lvm2 Metadata Areas 2 Metadata Sequence No 9 VG Access read/write VG Status resizable MAX LV 0 Cur LV 5 Open LV 5 Max PV 0 Cur PV 2 Act PV 2 VG Size 131.74 GiB PE Size 4.00 MiB Total PE 33725 Alloc PE / Size 4769 / 18.63 GiB Free PE / Size 28956 / 113.11 GiB VG UUID AhusW2-pzFv-3W32-mpv2-s5VG-FN7S-kVSadx $sudo lvresize -L +20GB /dev/mapper/vg-var So as you can see, it looks like adding the physical volume to the vg worked, because i see free space available there. When I typed the lvresize command, it never returned. I let this run overnight in the background, but this morning I still couldnt successfully do a "pvdisplay" or "lvdisplay" because I think it was waiting on a lock or something, so the command never returned. When i went to log onto the server's console, I saw a bunch of messages like: rcu_sched_state detected stall on cpu 2 Now when I boot, I get a kernel panic error, and a message about not being able to mount /mapper/vg-root cannot open root device "mapper/vg-root" or unknown_block(0,0) Kernel Panic -not syncing: VFS: Unable to mount root file system on unknown_block(0,0) What should I do to get my system back up and running? Did I attempt to do the logical volume resize correctly? Thanks

  Read the article

• I am having trouble booting 12.04 keyboard and little man in circle appears and then nothing

  - by Rich J.

  I have a new system (ASUS 990FX mother board, 2 western dig drives, 32 gb memory, an ASUS nvidia video card (GeForce GTX560), and an ASUS DVD Burner (24B1ST)) I am struggling to get the 12.04 cd to work. I have been able to see the little man inside a circle and a graphic of a keyboard? with an == sign between them. Is this is a clue? What does it mean? After that the mauve screen with keyboard and little man in circle goes away. I get a dark background and underline cursor... even hear some work being done reading the rom.... but nothing appears on the screen. I haven't even got to the point where the graphic card is displaying improperly... it is just not displaying anything. If any kind soul has an idea about how to proceed, I am all ears. BTW, I have posted the issue to ASUS... waiting for reply.

  Read the article

• Ubuntu hangs on booting up after a update

  - by alFReD NSH

  I've made a clean install yesterday, for the first time restarted, everything went good and then after I updated packages and copied my old home directory to replace the new one, when I restarted it hung when it was booting. I tried reinstalling again and doing the same thing, but again same thing happened. Here's what I see, before when the Ubuntu logo with the five dots is shown: Then after that, 3 or 4 of the dots will load and hangs there. If I press arrow up before that, this will be shown I started my laptop again today(the pictures are for the day before) and after that, boot up with live CD and got the logs. dmesg: http://pastebin.com/aVxV7BQF syslog: http://pastebin.com/4E2BrRUK And some info: alfred@alFitop:~$ uname -a Linux alFitop 3.2.0-24-generic #39-Ubuntu SMP Mon May 21 16:52:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: http://pastebin.com/AZbKJmsT sources.list : http://pastebin.com/2HazmuyV My problem is a bit similar to here: http://ubuntuforums.org/showthread.php?t=1918271 Though I didn't change my x.org config. Only changed home directory and updated packages. I've tried memtest and fschk, both passed. In the recovery mode boot option, I've also realized that same things happen in failsafe graphical mode. But when I go into the network mode, I can boot up my system, but of course same the graphics are just basic. Adding blacklist intel_ips to /etc/modprobe.d/blacklist.conf solves the first message, but still I get the broken pipe and CPU stack traces. The current kernel version is 3.2.0-25, I've tried booting up in the 3.2.0-23(the one the installer came with, but same results.) Also uninstalled apparmor, didn't help. I've installed Ubuntu again, this time without copying the home directory, also same result. --- UPDATE --- This problem was solved before with removing backports, but its back again! I've updated my laptop last night and the problem came back. It's definitely one of these packages. My /var/log/apt/term.log and /var/log/apt/history.log. I'm almost having the same situation. --- UPDATE --- I realized this also have happened on times that I have updated(haven't restarted after it) and my computer power has been cut off and its shutdown due to lack of power. And I realized if I just do as I answered but not in somewhere without GUI(networking mode has the GUI) it wouldn't work.

  Read the article

• Grub rescue - error: unknown filesystem

  - by user53817

  I have a multiboot system set up. The system has three drives. Multiboot is configured with Windows XP, Windows 7, and Ubuntu - all on the first drive. I had a lot of unpartitioned space left on the drive and was reserving it for adding other OSes and for storing files there in the future. One day I went ahead and downloaded Partition Wizard and created a logical NTFS partition from within Windows 7, still some unpartitioned space left over. Everything worked fine, until I rebooted the computer a few days later. Now I'm getting: error: unknown filesystem. grub rescue First of all I was surprised not to find any kind of help command, by trying: help, ?, man, --help, -h, bash, cmd, etc. Now I'm stuck with non-bootable system. I have started researching the issue and finding that people usually recommend to boot to a Live CD and fix the issue from there. Is there a way to fix this issue from within grub rescue without the need for Live CD? UPDATE By following the steps from persist commands typed to grub rescue, I was able to boot to initramfs prompt. But not anywhere further than that. So far from reading the manual on grub rescue, I was able to see my drives and partitions using ls command. For the first hard drive I see the following: (hd0) (hd0,msdos6) (hd0,msdos5) (hd0,msdos2) (hd0,msdos1) I now know that (hd0,msdos6) contains Linux on it, since ls (hd0,msdos6)/ lists directories. Others will give "error: unknown filesystem." UPDATE 2 After the following commands I am now getting to the boot menu and can boot into Windows 7 and Ubuntu, but upon reboot I have to repeat these steps. ls ls (hd0,msdos6)/ set root=(hd0,msdos6) ls / set prefix=(hd0,msdos6)/boot/grub insmod /boot/grub/linux.mod normal UPDATE 3 Thanks Shashank Singh, with your instructions I have simplified my steps to the following. I have learned from you that I can replace msdos6 with just a 6 and that I can just do insmod normal instead of insmod /boot/grub/linux.mod. Now I just need to figure out how to save this settings from within grub itself, without booting into any OS. set root=(hd0,6) set prefix=(hd0,6)/boot/grub insmod normal normal UPDATE 4 Well, it seems like it is a requirement to boot into Linux. After booting into Ubuntu I have performed the following steps described in the manual: sudo update-grub udo grub-install /dev/sda This did not resolve the issue. I still get the grub rescue prompt. What do I need to do to permanently fix it? I have also learned that drive numbers as in hd0 need to be translated to drive letters as in /dev/sda for some commands. hd1 would be sdb, hd2 would be sdc, and so on. Partitions listed in grub as (hd0,msdos6) would be translated to /dev/sda6.

  Read the article

• PLEASE HELP RECOVER MY MINT14 BOOT/GRUB [closed]

  - by C2940680

  Hi I have following from [bootinfoscript][1] v0.61 [1Apr-2012]: I tried to do several time to do a boot-repair from YannUbuntu. However, I get error rebooting into my Linux Mint 14 Cinnamon. I have partitioned /boot, /, /home partitions. Could I still use /home partition if I recover files on to external USB and then reformatting the whole hard drive, repartition and use /home from USB drive which I have saved before? Also, I tried to install Qubes 2beta and then deleted the partition where it was stored. Also, also {my bad} I tried to copy the BOOT.CFG from sda6 to sda1 and sda2. All answers appreciated in advance. sda1: __________________________________________ File system: ext2 Boot sector type: - Boot sector info: Operating System: Boot files: /grub/grub.cfg sda2: __________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________ File system: swap Boot sector type: - Boot sector info: sda6: __________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Linux Mint 14 Nadia Boot files: /boot/grub/grub.cfg /etc/fstab

  Read the article

• How can I get Ubuntu 12.04 to boot on a Gigabyte 990Fx MB (efi problem?)

  - by Jeffrey

  I am trying to install Ubuntu 12.04 on a home made system with a gigabyte 990Fxa MB. I can make it through the install process. It does not boot. Windows 7 does boot on the same machine. Suse 11.4 boots on the same machine. Suse 12.4 does not boot. I think there may be an issue with the EFI / GPT system. I know very little about these systems. I really expected the machine to boot. What can I do to get the system to boot? Please direct me to a path to trouble shoot this problem. thanks Jeffrey

  Read the article

• 'Invalid or corrupt kernel image' error while booting from USB stick

  - by steve

  I got the Ubuntu 11.10 32-bit edition and i used Unetbootin to write the ISO to a usb stick.After that i tried to boot from the stick,having changed the BIOS boot settings,and when the first interface shows up with the choices of istallation,whatever choice i select i got the message"invalid or corrupt kernel image".I use a netbook with windows 7 on it.I tried different usb sticks but same again.I also tried Universal USB installer instead of Unetbootin but same again.Any idea of what happens?I am using ASUS 1000H.The USB doesn't work in one more PC i tried to,but i also tried a second USB to both of the two computers and same again. I downloaded the ISO image once again and follow the same procedure but same again

  Read the article

• System unable to boot in normal mode..! need to select recovery mode and than Generic Mode to boot.?

  - by Haresh Veera

  I am using Ubuntu Server 12.04 LTS KDE Mode. Couple of Days back I updated the system using Muon Package manager. After Updating, now when ever I boot the system, It get stuck at starting bluetooth Daemon Ok / Stopping Bluetooth Daemon Fail.and after long wait its get start to GUI Mode, but with no mouse detection. So need to reboot by pressing CTL+ALT+DEL and when I select recovery mode - Boot in Generic -- It boot perfectly. How can I set the same as default, and remove the error boot loader script. I am no expert to linux or Kernel.

  Read the article

• Is there a current tool to build your boot / partition on hard drive?

  - by ????

  I tried Windows 8 Consumer Preview a couple months ago and it wiped out my partition table... or the boot information. So now the machine cannot boot to anything at all. Is there Ubuntu tools or Linux tool that can fix all the partition and make them boot again? (The partitions have Windows 7 and Vista on them. I run Ubuntu as a VM on Win 7). I tried another tool running on Vista and was able to see the Win 7 partition, except that tool wiped out the Vista boot info later on.

  Read the article

• Moved to SSD and now getting "the disk drive for / is not ready yet"

  - by dmt0

  I moved my Ubuntu 12.04 install over to an SSD drive. Copied all directories except for the ones most often written to - var, tmp, ... Reinstalled grub into SSD by booting with live CD and following the commands in this post: How to move Ubuntu to an SSD This seemed to work fine, because when I press "e" in grub menu, I see the expected UUIDs. But right after grub I get could not log bootup: Address already in use the disk drive for / is not ready yet or not present. If I skip, I get same for /tmp /run, and other dirs If I go into manual recovery and do mount -n -o remount,rw / it turns out that everything can mount no problem. Can't get my head around this one. My fstab seems right. grub is right. AHCI in bios is enabled. Why is this happening? What can I do to fix it? When I do drop into shell from this error and get to mount things manually, how do I get the OS to continue loading? Thank you guys for any ideas you can give me. Here's what my fstab looks like right now: # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 UUID=67fc8a7a-f1db-485c-88bd-e007c214244f / ext4 defaults,noatime,discard 0 1 # swap was on /dev/sda3 during installation UUID=6bc9cd6c-46b7-43a0-bfac-bd04cc26cfb6 none swap sw 0 0 UUID=7397729b-2125-4b1d-b5eb-28866898d773 /hdd ext4 errors=remount-ro 0 1 /hdd/home /home none bind 0 0 /hdd/run /run none bind 0 0 /hdd/tmp /tmp none bind 0 0 /hdd/var /var none bind 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 output from blkid: /dev/sda1: LABEL="System Reserved" UUID="EABC56C1BC568849" TYPE="ntfs" /dev/sda2: UUID="7CCC6124CC60D9C2" TYPE="ntfs" /dev/sda3: UUID="6bc9cd6c-46b7-43a0-bfac-bd04cc26cfb6" TYPE="swap" /dev/sda5: UUID="7397729b-2125-4b1d-b5eb-28866898d773" TYPE="ext4" /dev/sdb1: UUID="67fc8a7a-f1db-485c-88bd-e007c214244f" TYPE="ext4" relevant from fdisk -l: Device Boot Start End Blocks Id System /dev/sdb1 2048 115345407 57671680 83 Linux

  Read the article

• XUbuntu won't boot

  - by Slava Fomin II

  I can't properly boot my XUbuntu desktop. It just hangs on the console without any visible errors. The only way i can boot it properly is choosing "recovery mode" in GRUB and then selecting "continue booting" in recovery menu. It's really annoying. I provide some logs here: http://www.sendspace.com/filegroup/mQ%2FzdWvVcrjB3dz4vVqjsw Please advise! If you need some additional information i will be glad to provide it. Any hints and support will be much appreciated.

  Read the article

• 12.10 on Elitebook 8560w w/ WUBI

  - by iSeth

  I am trying dual boot Windows 7 and Ubuntu on my Elitebook 8560w via WUBI. Between Microsoft and HP they used up all my primary partitions so I decided WUBI was the best way to go. It all goes smoothly until I reboot to finish the installation, then it hangs at copying files. It always freezes here: debconf (filter): widget found for ubiquity/install/title debconf (filter): -- 0 OK It also says something about "so and so might freeze best to kill it" but I didn't get it written down. Can anybody tell me what that means? EDIT: This is what it says (In Full): ubuntu kernel: [365.130914] [<c1064d607] ? kthread_freezable_should_stop+0x60/0x60 ubuntu kernel: [365.130914] [<c15d04fe7] kernel_thread_helper+0x6/0x10 debconf (filter): <-- progress set 49 debconf (filter): widget found for ubiquity/install/title debconf (filter): -- 0 OK debconf (filter): <-- progress set 50

  Read the article

• Unable to install ia32-libs package

  - by Ron Thomas

  I need to manually install the drivers for my graphics card, which is an ATI 2600 xt. But I am using a 64-bit platform and to do so i need the ia32-libs package. i have scoured the net for fixes, workarounds etc. but have found none that work. the output i get after trying apt-get is: Reading package lists... Done Building dependency tree Reading state information... Done Package ia32-libs is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'ia32-libs' has no installation candidate I am running linux mint 12

  Read the article

• Live-Ubuntu 12.04 ran fine, now stopped booting!

  - by user89743

  I've seen similar problems to this several times in the forum, but mine is a bit different, so the other posts I saw were no help to me. When I boot Ubuntu 12.04 64-bit from live-SD-card (3GB persistence) I suddenly get this error: (initramfs) mount: mounting /dev/loop0 on //filesystem.squashfs failed: Invalid argument Can not mount /dev/loop/0 (/cdrom/casper/filesystem.squashfs) on //filesystem.squashfs (it says I can type "help" for commands, but I don't know anything about how to go from there, totally new to linux) The reason I say my case is different is because my Ubuntu worked fine for over a week, even pretty fast, and now this problem happened. Before that I used to run my live ubuntu from USB sticks but that was slower (especially when booting which took 15 minutes from USB stick!). Also I kept getting the same above problem after a while when booting and had to re-create a live USB linux several times. Installing on harddrive is not an option because my harddrive has physical damage and getting a replacement will take a while, therefore I can only use live-USB or live-SD-card Ubuntu. As I said I used Ubuntu without problems for more than a week, before that as well for several weeks on USB sticks, but the above problem occured sooner or later. This time I paid attention to when it happened: I was rebooting my computer (HP 620 laptop, 4 GB RAM, 64 bit system) from SD flash card and when I was booting I selected F6 and then the first option "no acpi" or something like that...I had used it before and noticed it slowed down the time it took Linux to use. This time it caused this error. Now even when I boot normally/default I get this error. Now I'm accessing Ubuntu from my USB stick without persistence file, when I check my SD card, all the files mentioned in the error message are there and the filesystem.squashfs is 691.2 MB so nothing seems to have been deleted by accident. (I have already made many changes/downloaded programs to my SD card persistent Ubuntu and would hope to loose them, since downloading is expensive for me, and since the problem seems to re-occur...) Can anyone help me, preferably without having to create another startup disk on my SD card? I'm totally new to this. Sorry for the long posts, just didn't know what info is relevant and what isnt! Kon

  Read the article

• How can I rescue a Lubuntu install?

  - by Ghost

  Quick recap: I was having a problem with hibernation so I check and the linuxswap partition is missing, showing an "unknown" chunk of drive where it was. Happened before, booted to the liveCD and used Gparted to reformat that partition back to swap. Then I boot........F---- grub rescue... MBR took care of the problem, except that now I'm back to Windows only. EVERY guide out there makes me reinstall Lubuntu from scratch, a waste of time considering it will take me at least a day to reinstall everything there. Can't I just fix grub like I did with the win MBR?

  Read the article

• Unable to start GRUB2 on Triple boot Macbook Pro with OS X Lion, Windows 7 and Ubuntu

  - by Shravan

  I installed Windows 7 using Bootcamp. Then I created a partition from the empty space in the Windows partition and another 4GB partition for the linux swap using GParted. I installed Ubuntu 12.04 LTS in the the newly created partition from the Windows partition. Now GRUB2 does not load and I can only see the blinking cursor on the top right when selecting "Windows HD" from the 'option' key at the start up. OS X works fine but nothing else. Could someone please help me fix this? I am attaching the boot-info from the boot-repair tool. http://paste.ubuntu.com/1040169/

  Read the article

• Ubuntu multiple issues (blank screen)

  - by Donavon

  Computer Specs I am having difficulties, to get Ubuntu 11.10 to work. For the 11.10 version, if I click install, or if I click try Ubuntu, I only get a blank screen, that just stays there. If I use "nomodeset", it changes to a loading screen and after about 2 minutes it goes back to black screen - however, before it goes black, i get a few errors, like: bad target number, or passwd error mode (something like that). I've also tried (xforcevesa, i915.modeset=0, nomodeset, radeon.modeset=0, i915.modeset=1) I have also tried the alternate installation, which installed fine, however when I boot up, select it from "grub", it goes black. I did manage to install 10.04, however the screen resolution was 800x600 and I couldn't fix it to 16:9 (my resolution). I don't wanna use 10.04, because I would like the new one 11.10, and would like to use it. Any help would be GREATLY appreciated. Thank you

  Read the article

• Newly compiled (patched with -ck) 3.3 kernel won't boot up

  - by Shiki

  Screen is garbled. Reaaaally garbled. Like some sort of scrambling image from a movie. I can upload some pictures if needed. To be short with the description. Here is my 3.3 + ck .config file: http://pastebin.com/aP2F9RcH The dmesg log of the failed kernel: http://pastebin.com/esc2Rtka The computer is a ThinkPad T500 laptop. I have selected everything needed for the computer (as far as I can tell, but check the .config). The normal generic Ubuntu kernel boots and works perfect!

  Read the article

• Ubuntu 12.10 hangs on checking battery state

  - by Waxolunist

  I have a Thinkpad X230. After a boot it hangs with checking battery state [OK]. A second boot is most times successful. What I have seen in other posts doesn't fit to my problem, because My graphics card is Intel 3rd Gen Core processor Graphics controller (not nvidia) It happens not always I have a fresh installed 12.10 with the latest updates (no upgrade) Does anyone experience the same issues or has a solution?

  Read the article

• Grub2 attempting to boot hd1 when it should boot hd0

  - by JoBu1324

  I'm attempting to perform a "normal" install on a USB3 SSD (I don't know if it is noteworthy, but I don't have a swap partition). The installation proceeds normally (I'm installing from a USB2 device I created using LiLi Boot, with a copy of Ubuntu 12.10 64bit that I downloaded directly from the source. The system I'm running Ubuntu on has had a more traditional installation of ubuntu running on it without issue (also 12.10), so I know that everything works A-OK when booting from a 7200RPM internal disk. There are a number of oddities that I've noticed so far, including graphics corruption, but the first and most pressing issue is that Grub2 refuses to recognize the correct hd. From /boot/grub/grub.cfg: if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd1,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd1,msdos1 --hint-efi=hd1,msdos1 --hint-baremetal=ahci1,msdos1 b58ee4f7-d41d-400a-b7b8-18bd1f0ae9d3 else search --no-floppy --fs-uuid --set=root b58ee4f7-d41d-400a-b7b8-18bd1f0ae9d3 fi font="/usr/share/grub/unicode.pf2" fi This is from a 100% fresh install of linux (first boot), which was installed while no hard drives were connected to the system, other than the USB2 LiLi drive. The system refuses to boot unless I change the hd1,msdos1 - hd0,msdos1 in the grub menu at boot, when it is the only disk device connected to the PC. What options are left for me to troubleshoot this issue? I've been racking my brains and taxing the internet trying to dig up something on this problem, but now I'd like to see if the Ubuntu community can rise to the challenge and help me fix this boot problem. This is the second time I've attempted this particular setup. The first time, after days of wasted time, I managed to get it to boot every other boot - i.e. every even boot it would boot into Ubuntu like it was happy; every odd boot it would boot into the BusyBox or Grub prompt. At one point it complained that it couldn't find /dev/disk/by-uuid/[the disk], which I found most perplexing, since the disk was there and booted before and after the occurrence (with intervention).

  Read the article

• Dell M4600 with nVidia Quadro 2000M hangs on boot when external monitor is connected

  - by vladeta

  I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

  Read the article

• Windows Defender Update KB915597 (Definition 1.135.415.0)? Killed My Live Discs

  - by user88311

  Here's my problem, for those willing to read for about 2 minutes here's the entire story, http://answers.microsoft.com/en-us/windows/forum/windows_vista-windows_update/bsod-after-windows-defender-update-kb915597/a4b5fca3-0274-47b4-97c4-61b34c4c4599, for those who want the short version here's what happened. After windows update automatically updated windows defender to kb915597, my computer starting getting bsods on shut down and start up and started experiencing problems withe the usb ports. So I decided to go to the microsoft answers site for help, I know that was probably my first mistake, so I followed their advice and they turned my computer into a large paper weight. Luckily I make physical backups of my c drive every few months and I have one from back in july, so I figured I'd boot up a ubuntu live disc, copy all my files from the past 2 months to a external drive and just copy the backup back to the c drive, that's where I ran into this problem. When I put in either a ubuntu or kubuntu disc, everything goes well, until it finishes the loading bar then when the OS would presumably start up, the computer resets, I've tried with ubuntu, kubuntu and gparted, and only gparted is able to get to the point where it starts up, but even then when I try to access the internet from it, the computer resets, and when I tried to copy the entire C drive partition to a blank external I wasn't able to. So I figured somehow maybe the C drive had something to do with it, so I unplugged the C drive so my computer was just a 2.8 ghz processor and 2 gigs of ram, should have had no problem starting a live disc but the problem still continues. After doing some googling around I've found whenever windows gets a update with the title KB915597 it's pretty much the kill switch for windows, I've tried contacting microsoft tech support and even managed to directly contact a software engineer but as soon as I mention KB915597 they all just blew me off. I hope anybody who reads this has any idea how to fix this, I'm going to attempt to install ubuntu or kubuntu to a external drive using the same computer and see what happens now.

  Read the article

• Can't n run a bootable cd of ubuntu desktop on a laptop with no OS

  - by csbl

  I recorded a bootable CD with the image that I downloaded from the Ubuntu site, using NTI CD MAKER. My laptop had a problem and I prefered to get it fixed without installing an OS. Now, when I try to run this CD it shows the following error mssage: Device driver not found: 'MSCD001'. No valid CDROM device drivers were selected Mouse driver was previously installed A:\> If the drive wasn't working the CD wouldn't even start, I assume....So can anyone help me please! Thank you!

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >