Search Results

Search found 7065 results on 283 pages for 'vmware player'.

Page 14/283 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• Fedora 12 on Vmware network disabled on restore

  - by Chaitanya

  I have a fedora 12 guest running on VMWare on windows 7. I use it mainly for the occasional linux dev. Whenever I restart the guest, networking works fine. But if I close the VMware player and save state, the next time I start the image, networking is disabled (red x on the network icon. message saying networking disabled). I can't seem to find a way to restore networking. I have to reboot the guest to get my network access back again. My Ubuntu image doesn't have this problem. I can close the player and when I re run the image, I can pick up where I left off, with all the open firefox windows and application windows as I left them. Fedora saves state, but doesn't seem to enable networking. There is a relevant warning I have seen "SELinux is preventing /sbin/ifconfig "read" access to/var/run/vmware-active-nics." But I am not sure how to solve it. I know fedora isn't officially supported by VMware, but it seems to be working fine for the most part and meeting my needs, except for this one little issue. Any help would be much appreciated.

  Read the article

• Ram question in VMware Server 2

  - by ToreTrygg

  Hi, I understand from the VMware Server 2 documentation that VMware Server 2 is capable of running a 64-bit guest OS underneath a 32-bit host OS, as long as the hardware running the box is 64-bit capable. Here's my situation. We currently have an underutilized XEON X3220 Quad Core 64bit Server, running Server 2003, 32-bit and 2gb of RAM (the motherboard is capable of 8gb ram). The server is currently used mainly for file and print services. It is also running Active Directory, Novell eDirectory and Groupwise 6.5. We are planning a micration to Microsoft Exchange, so the Novell eDirectory and Groupwise services will eventually be purged from this box, leaving only Active Directory, File and Print services. Being that this server is underutilized we are hoping to save hardware costs and virtualize our new Exchange investment. My question is this. Will VMware allow access to the "invisible" extra memory that Windows 32-bit won't see. Meaning, if we increase the full amount of system ram to 8gb (yes, I know the 32-bit host OS will only see a maximum of 4gb), will I be able to assign maybe 5gb to the new Server 2008 64-bit OS running Exchange and leave 3gb for the Guest OS (or maybe even a 6, 2 split). The second part of that would be, would it be better to just convert the main OS currently running to an image, convert the machine itself to ESXi and run both OSes as images under ESXi. Downtime for this box is critical, so my preference is most definitly with the first option because it presents very minimal downtime. Doing the second would make downtime quite a few hours to image the machine and then convert the image to a VMware Image.

  Read the article

• Make vmware virtual machine from HDD with bad sectros

  - by mike1616

  I have a notebook with a bad HDD (it has bad sectors). I would like make a virtual disk with VMware workstation from this computer. I installed VMware Workstation & VMware vCenter Converter Standalone Client on this notebook, then I used virtualize a physical machine. It started procedure but at 38% I got this error: FAILED: An error occurred during the conversion: 'BlockLevelVolumeCloneMgr::CloneVolume: Detected a write error during the cloning of volume \WindowsBitmapDriverVolumeId=[39-06-3A-06-00-02-13-4C-1D-00-00-00]. Error: 209 (type: 1, code: 13)' I Googled it and I think it means that I have bad sectors on the HDD. How can I solve this problem and make a virtual machine from HDD with bad sectors?

  Read the article

• Ubuntu 11.04 VM shows a black screen in VMware Player

  - by Roel Veldhuizen

  I have a Ubuntu Server 11.04 64 bit VM running on VMware Player 3.1.4 that only shows a black screen. No matter what I try, the screen remains black. The VM has worked the first time. When I reset the machine, it shows the VMware loader and a flickering _ for about a second. Then the screen turns black again. VM settings: Memory: 512MB Processors: 1 HD: 20GB CD: auto detect Floppy: auto detect Network adapter: NAT USB controller: present soundcard: auto detect printer: present display: auto detect I just created a fresh VM and the same happens, so it seems that the problem is consistent.

  Read the article

• VMware ESXi - varying CPU time (CPU reservation)

  - by Tomo

  Hello! I'm running FreeBSD 7.2 under VMware ESXi 3.5. Host has 2 physical CPUs and the BSD box is currently the only running VM. Only one virtual CPU is assigned to the VM. When measuring CPU time of a specific program, I get very different results from time to time. Processor usage is reported differently by VMware, based on the system load. Is it possible to assign a constant share of a physical CPU to specific VM? I would like the CPU time to be more or less much constant. I tried setting CPU reservation when configuring VM in the VMware Infrastructure Client, but the CPU time still varies a lot. Thanks in advance!

  Read the article

• Do I need VMWare vSphere?

  - by Gk

  I'm planning use vmware to upgrade some of very aged server instead replace with all new bunch of server. VMWare vSphere sounds great but because of low budget I can't afford for both licenses and SANs. Without SAN, is vSphere worth the price? As I know without SAN, the VMWare HA, VMontion, FT is unavailable. So, do I need vSphere or only ESXi free version assume that I only need backup vm daily? Do you know any completed solution about backup on ESXi 4? TIA, -Gk

  Read the article

• Problem after resizing partition for Fedora under Vmware fusion

  - by user20196

  Hi, I am running FC9 under VMware Fusion 3.0 I wanted to resize my /dev/sda2 partition. In order to do that I did the following: 0. changed the size of the vmware file (under VMware settings). 1. rebooted the host to rescue mode without mounted disks 2. fdisk - removed & added /dev/sda2 - i had bigger /dev/sda2 3. lvm pvresize /dev/sda2 4. lvm pvdisplay - it showed me bigger size on /dev/VolGroup00 for /dev/sda2 5. lvm vgchange -a y - device-mapper: reload ioctl failed: Invalid argument - 2 logical volume(s) in volume group "VolGroup00" now active This is not true because there is no /dev/VolGroup00/LogVol00 My whole "/" disappeared. dmsetup table, shows: VolGroup00-LogVol01: 0 2097152 linear 8:2 38338944 VolGroup00-LogVol00: Can some one help me to solve this? Thank You.

  Read the article

• VMware vSwitches and Dell PowerConnect BPDU guard

  - by dunxd

  I am using two Dell PowerConnect 6248 switches to connect a VMware host vSwitch. A discussion of config of Cisco switches for use with VMware advises to set physical ports connected to vSwitch with bpduguard and portfast. However, Dell switches don't have the bpduguard setting for individual ports. I can switch it off globally for all portfast ports, but I don't think I want to do that. Should I: Disable STP on the vSwitch connected ports? Leave STP on and enable portfast on the ports, and forget about bpduguard? Disable bpduguard on all portfast ports via global config Do something else? See also: VMware vSwitches and spanning tree

  Read the article

• Internet connection sharing: Ubuntu 9.10 Server on Windows 7 and VMWare

  - by avesse

  I'm trying to get Internet Connection Sharing (ICS) working between my Windows 7 RTM host and a Ubuntu 9.10 Server running on VMWare Workstation 6.5, but I have not been able to get it right. Here's what I have done: Configured VMWare to use Host Only networking (I tried NAT as well). Enabled ICS on my host's network connection, allowing VMnet1. After enabling it, Windows informed me that its VMnet1 IP has changed to 192.168.137.1. So in VMWare's Virtual Network Editor I configured VMnet1: Subnet 192.168.137.0 Mask 255.255.255.0 I did the same for DHCP. For NAT i set 192.168.137.1 as Gateway. I cannot ping any sites or get access through apt-get/aptitude install/update, although domains do get resolved to IPs. I have also tried using a static IP in Ubuntu. I don't know if it makes a difference, but my external IP is locked to my host's MAC address.

  Read the article

• Windows 7 Activation with Bootcamp and VMWare

  - by Jason Hernandez

  I have windows 7(64) installation setup on a Boot Camp partition on my MacBook Pro 13". I also access this partition through VMware hosted by OS X (snow leopard). Every time I switch between VMware and Boot Camp windows says that it needs to be re-activated because of hardware or driver changes. I've tried wmware KB KB 1003426 to no avail. Edo Thanks, Jason Edit, I am using the most recent VMware and tools. I've tried "KB 1004917" as well. No Dice. I'm considering re-installing at this point.

  Read the article

• Running bridged-networking vmware player on a Linux machine with 2 interfaces

  - by Roman D

  I have got a laptop running Arch Linux with 2 interfaces: wireless (wlan0) and ethernet (eth0). I use wlan0 to access internet (static IP, networking is configured using netcfg), and I connect a second PC to the eth0. Now, whenever I start vmware player (v. 4.0.4), it chooses wlan0 to connect its bridged virtual NIC to, but I need it to connect to eth0 (I want my guest machine to be able to talk to the second physical PC on eth0). So, I disable the wlan0 interface (netcfg -d wireless) and restart vmware. Now, it connects to eth0, and everything works fine; I can ping the host PC from the virtual one, and I can ping the virtual PC from the second physical PC connected to eth0. Then, if I try to reenable the wlan0 interface (netcfg -u wireless), all of the connectivity between the host and the guest (and between the second physical PC and the guest) gets lost, until I disable wlan0 again. Can someone please give me a hint on what's going on?

  Read the article

• Back / Forward mouse buttons do not work in VMWare Workstation 6.5 Guest OS

  - by Tim Lara

  I am using a Logitech G9 mouse and running VMWare Workstation 6.5.3 on Vista x64. The guest OS is Win XP, and has the most current version of VMWare Tools installed. Left / right buttons and mouse wheel scrolling work fine in the guest OS, but the back / forward buttons are apparently not recognized. I have tried installing the Logitech software inside the guest OS as well, but it still did not recognize the back / forward buttons. (I didn't really expect this to work since the guest OS doesn't actually see the mouse hardware as a Logitech G9 directly anyway.) I vaguely remember seeing something a while back about editing the virtual machine config file to specify a 5-button mouse rather than the default 3-button setup, but I can't seem to find any specifics on how to do so in the VMWare documentation. Does anyone know if such a workaround exists, or is 5-button mouse functionality just not supported?

  Read the article

• Moving VMWare Fusion image to Boot Camp

  - by Kristopher Johnson

  I have Windows 7 64-bit running in VMWare Fusion on my MacBook, but am disappointed with the performance, and so I want to try Boot Camp. However, I'd like to avoid reinstalling Windows and all my applications; I just want to somehow copy my VMWare Fusion "disk image" to a Boot Camp partition. My initial thoughts are that I should be able to run a Windows backup program in VMWare Fusion to back up the entire virtual disk, then set up Boot Camp and restore from that backup. However, Googling finds a few posts by people who have tried that and have encountered problems. So, is there a "known good" procedure for doing this?

  Read the article

• VMWare Headphone Issue

  - by Ash_Geek_Pickney

  I am running VMWare Workstation Version 7 on a Windows 7 partition on a Macbook Pro. I have built a virtual XP machine within vmware to run some old music programs. The sound from my virtual machines comes out of my macbook speakers but the volume is not controllable using my macbook volume controls, only by using the volume control on the XP machine. My problem is that i need to use headphones, and when i plug a headphone jack into my macbook, the sound from my vmware virtual machines still comes out of the macbook speakers. I am baffled. Please help. Thanks in advance...

  Read the article

• VMWare Server 2 Install is Failing w/ Error 25032: "failed to customize windows logon process"

  - by Justin Searls

  VMWare Server 2 install question here.* Straightforward question that would probably require a VMWare expert to pull apart, given that Google has been totally worthless on this. On a patched Windows XP machine, any attempt to install VMWare Server 2.0.1 results in failure, just prior to completion (progress bar is full but I can tell network adapter stuff hasn't been fired yet and most of the services haven't been instaled). The error: Error 25032. Failed to customize Windows logon process (). Please contact your administrator. Upon dismissing the error, you're treated to: Warning 25033. Failed to remove Windows logon customization (VMGINA.DLL). Please contact your administrator. Clicking "OK" rolls back your installation. Killing the installer and hoping that it somehow leaves a working install behind was also unproductive. *I hope install troubleshooting isn't outside the purview of serverfault, I'm typically an SO user.

  Read the article

• Converting a VMware player image from non-persistant to persistant

  - by Journeyman Geek

  I'm pondering setting up a virtual machine to generate app-v (since i got mdop from school) or thinapp application virtualisation packages. Ideally with either of these, i should work off a fresh system do the install, then copy out the packages produced. I'd like to not have to reinstall windows per package to get a fresh, unmodified stock copy of windows. I'm aware that its possible to make a hard disk image persistant in vmware player (one of my lecturers did it, but he's in another country). I'm wondering how would i convert a persistant image to a non persistant one? I'm currently running vmware player 4, with windows 7 guest and host.

  Read the article

• VMware Workstation 9 Security Best Practice Guides

  - by slickboy

  Could someone please point me in the direction of where I could find some best practice securiy guides for VMware Workstation 9 please? I've searched the VMware site and to say it's badly organised is an understatement! I've been able to find general setup guides but nothing with a specific focus on security. I'm also wondering is there any best practice guides that I should follow when installing Windows 7 Professional and Windows Server 2008 R2 on VMware Workstation 9? I obviously will be implementing Microsofts recommended security best practices but I'd be very interested in any recommendations for virtualizing these operating systems. Any help is much appreciated.

  Read the article

• Preparing a new physical system with VMWare

  - by Max

  I need to create a new installation of Windows, but at the same time I need this computer. So I decided to create a new physical disk from within VMWare, install windows/drivers/software and then just replace the HDD in the computer. I've bought a new HDD, split it into two partions and installed Windows 7 using the VMWare's ability to use phusical disks. I can see the windows files and directories that have been created on this partition, but when I'm replacing the HDD in the host machine it cannot boot from it. Why is that? Is it at all possible to create a bootable physical disk with VMWare or I should create a virtual disk and then use some HDD imaging tool to copy the HDD image to a physical disk? Maybe there's a better way of installing a new system and working on the computer at the same time?

  Read the article

• Problems connecting Centos to the network when running in VMWare

  - by Sakin

  Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. I tried to configure VMWare to use a bridged connection as well as NAT connection. An image of Ubuntu runs fine on the same VMware. What am I missing here? Thanks.

  Read the article

• SAN alternative for VMWare

  - by CogitoErgoSum

  Has anyone utilized something aside from a SAN to run their VMWare images off? We are looking to drop in two HP Servers and VMWare on them and run them off a SAN. Due to the cost of SAN though our CFO and VP are wondering if there are any viable alternatives (I.e. NAS) that can effectively run a VMWare. I can't think of any off of the top of my head. IF anyone can provide one or a good article outlining why to stick to SAN that'd be great.

  Read the article

• [SOLVED] vmware problems - networking - no packet response

  - by jack

  XP is my host. Ubuntu is my Guest in VMware. When I do the following commands, I should get SMTP respones but now get no response. I use wireshark to analayze it. Also in wireshark shows nothing. root@vmware:~# netcat 192.168.1.2 25 220 762462a8c4d Microsoft ESMTP MAIL Service, Version: 6.0.2600.5949 ready at Fri, 12 May 2010 18:04:20 +0800 EHLO SAYHELLO VRFY TEST@LOCALHOST test \ sdfsafsd How can I fix it? UPDATE: I came to know that this is no VMWare problem. This is Netcat problem. For this, you might have to type Ctrl+M {ENTER} {ENTER}

  Read the article

• virtualbox 2 vmware disk

  - by anol

  I have a virtualbox disk I'd like to convert to a vmware disk. The disk is dynamic which makes it a lot more trickier. If I follow the instructions at http://xpapad.wordpress.com/2010/02/21/migrating-from-virtualbox-to-vmware-in-linux, the vdi-to-raw conversion will result in a 2 TB file. I don't even have that much disk space! The first step therefore seems to be a dynamic to static conversion of the virtualbox disk, right? How do I do that or is there perhaps a better way to convert to vmware? Help!

  Read the article

• Testing a Virtualisation of a Debian Server (vmWare vSphere probably)

  - by xyza

  I'm soon getting access to a powerful root-server (quad-core, 16gb ram, 1gbit connection) where gameservers (like minecraft,counterstrike etc.) for different customers should be setup. My plan is to use programs such as vmWare vSphere to create some virtual machines for each customer. Inside such a virtual machine I'll setup the gameserver and maybe some kind of ftp server when its needed. Now that I'm kinda new to virtualisation of servers I want to test this local on my Desktop Computer. Is it possible to create a virtual machine of debian using vmWare Player on my Windows desktop computer and then install vmware vSphere in this VM to create multiple VM's inside that VM ? Or do I really need to install Debian on my desktop computer. (I want to use the time during installations etc. to work a bit at my windows installation) Some tips on virtualising debian servers are also appreciated :)

  Read the article

• Accessing VMware Player across the network

  - by Tiffany Walker

  My network: 192.168.2.2 (computer) 255.255.255.0 (mask) 192.168.2.254 (gateway) The VMplayer is: 192.168.233.129 (ip) 255.255.255.0 (mask) 192.168.233.255(bcast) It's obvious the player can't be access from other systems because of the wrong network settings. However, I am not sure as to how to change that. Obviously I have to edit the ifcg-eth0 but I know I also need to edit it on the host system to make it accessably. Is this done from inside VMware Player? Or do I need to edit the network devices? The host box is Windows. Inside VMware is Linux.

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >