Search Results

Search found 6502 results on 261 pages for 'dont reinvent the wheel'.

Page 140/261 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Reg: Putty SSH Access

  - by gourav

  Dear all, I have a Linux based virtual server recently purchased. I need to transfer the files from local computer to my virtual server... I tried downloading the Putty. But there were no EXE files to install. i am using Windows XP at home. If possible, can i have to installer link. Do we need to know Linux compulsorily for using this Putty. And also is there any other tool which can be used by users who dont know linux commands. Please help.

  Read the article

• Intel PRO/1000 Server NIC on Windows latency. How to measure?

  - by Bobb

  Please note - this question is about latency of the card itself. Not latency of internet or anything else. Thank you for your attention on this matter. It is often said that good server NIC does make difference compared to low grade cards and on-board Ethernet chips. I understand that on-board chip will likely consume CPU time and stand-alone card would use its own chip. Also server card would be faster than low-grade card. Are these 2 facts explaining most of the server cards advantages over on-board and low-grade cards ethernet? How would you measure latency on the card itself? I saw some reports stating some microseconds figures of NIC latency but I dont see how to measure that... Any advise will be appreciated.

  Read the article

• Email error 'Default email client is not properly installed' after installing Bugzilla 3.6.3 on Windows Home Server 2011

  - by Brian Frost

  I have been using Bugzilla fine on the older 32-bit Windows Home Server and I have now started a migration to the newer Windows Home Server 2011 with a new machine and a fresh Bugzilla install of 3.6.3. All goes well until I try to check out the email action and I get 'Could not perform this operation because the defaulty mail client in not properly installed. Is this a security /firewall issue? I dont know enough about servers to know what to look for, so any help will be gratefully appreciated. Thanks.

  Read the article

• How to see whats taking up space on your hard drive

  - by sam

  Im thinking of switching to one of the macbook pro retinas with a 256gb ssd, im making the move from a 512gb hd, which at the moment is split into a 60bg windows partition (which i dont think im going to have on my new machine) and a 440gb main partition of the main partition ive got 140gb free. So all in if i disregard the 60gb windows part ive got about 200gb free so im using 300gb, which is still a bit to much, ive had this machine 4/5 yrs so its likely to be clogged with files that i no longer need, is there a tool that i can use to view my current hd and see whats taking up the most room, so i can begin to see where i can cut down ? just for a bit of background my current machine runs osx.

  Read the article

• Burn more than one ISO to one dvd?

  - by Doug

  I just turned 11 CDs with a total of 1gb of stuff into ISOs. Is it possible for me to just burn all the ISO videos into a DVD? Any alternative way for me to do it? Edit: I need to be playable on any DVD player. It's videos for my grandparents. Update: I read that DVD shrink should work (re-authoring software), but I didn't try it because when I imported the VIDEO_TS folders into the software, my video wasn't played widescreen, and I dont' know how to fix it.

  Read the article

• Exchange 2010 Room Mailbox Calendar Permissions

  - by Brian Mitchell

  Exchange 2010 sp2 Outlook 2007/2010 Server 2008 I have managed to set up several room mailboxes in exchange, people are able to book the rooms and they get a response from the exchange server. this is brilliant. however users are unable to view the calendar of the room mailbox to see what times are available, in a ideal world I would like users to only see if the room is free or not. I dont want users to see the details of the meeting (title, description etc) I have been trying to do this using the following command Add-MailboxFolderPermission -Identity meetingroom -User "Usergroup" -AccessRights AvailabilityOnly -DomainController AD-Server This throws the following error Specified argument was out of the range of valid values. Parameter name: memberRights + CategoryInfo : NotSpecified: (meetingroom:MailboxFolderIdParameter) [Add-MailboxFolderPermission], Argum entOutOfRangeException + FullyQualifiedErrorId : CBC6516F,Microsoft.Exchange.Management.StoreTasks.AddMailboxFolderPermission Any help on the situation would be brilliant, i have been trying to get this done for a couple of days and im going around in circles.

  Read the article

• Windows server 2003 mapping home drive wrong

  - by Sandman2010

  hey all, first question... we have around 30 servers in an Active Directory environment with 600 student computers and 100 staff desktops with XP SP2/3, the win server 2003 has the staff home drives on a NAS and in the last few days after some server updates is now mapping home drives to the \servername\home instead of \severname\home\%username%, its simple to re map the network drive but is annoying. we dont use login script to map home drive but use a VB script for other network drives and if we add the home drive mapping to that it works, but shouldnt the profile option in users AD account map that correctly? which do you all recommend, AD profile mapping or VB Script mapping Home drives? thanks Steven

  Read the article

• How to Disable secondary drive from booting upon restart - Windows

  - by DevCompany

  I had a Windows 2003 Hard Drive on my server and it went bad so I installed a new clean hard drive and installed Windows 2008 R2 on the new clean drive. I moved the old 2003 drive to be used only for general storage on the same computer. It usually boots into Windows 2008 upon a restart, but just sometimes it starts trying to boot the old 2003 drive and causes boot issues(NTDLR Bootloader, and other errors), even though the order of boot preference is set to boot 2008, and NOT 2003. I need to know how to remove any old code that keeps this old drive as a bootable drive. I still want to use it as a secondary drive just dont want to have any boot code on it. hopefully my situation is clear for everyone to get a good response. Thank you...

  Read the article

• logitech unifying receiver

  - by Plastkort

  hi! I am having multiple logitech devices, and each and one of them seem to have theire own receiver, occupying USB ports.. I read upon Logitech unifying receiver, and it seem to connect multiple wireless devices from logitech, however I wonder if I just buy this one receiver, will I be able to connect my existing wireless devices, or will I be forced to buy new keyboard and mouse in order to use the unifying receiver? hope anyone here have the answer so I dont need to spend money on something I cannot use.. :) I got PC 1 Logitech Dinovo Edge keyboard Logitech MX Air mouse PC 2 Logitech Dinovo Keyboard Logitech VX mouse

  Read the article

• Changing Internet connection on ISA Server 2000

  - by garyb32234234

  Hi We are getting a new internet connection installed and will need to unplug the old one and connect this to our ISA Server 2000. Will this be a simple swap out job? We will be given a new ip, which i know i will have to enter into the external network card TCP/IP page. I will also be given the default gateway to enter. The ISP engineer said we may have to reset the ARP? cache, if we dont know how we will have to reset the ISA server? Has anyone any experience? The current connection is with the same ISP but it was owned by the business park were we are located and they linked up an ethernet port to what i assume is their own router. Hope you can help, i know that ISA 2000 is somewhat less easy to use than the newer versions.

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• Cannot start eventlog service

  - by ANervousTwitch

  On a windows 2k8R2 DC box the eventlog service wont start. When i try to start the service the machine returns: "Windows could not start the Windows Event Log service on Local Computer. Error 13: The data is invalid." event viewer wont open either. obviously, i dont have an event log for this error. ive already tried clearing the event logs. that didnt do anything. the other DC isnt experiencing this issue.

  Read the article

• test if master dns has trasnfered copt to slave

  - by su55

  Hello, I setup my master and slave using freebsd. im currently running the Bind 9.X version, so far everything is working successfully. Just one small problem. I cant get the master copy of my dns to transfer it to the slave server. i included transfer-allow {192.168.1.111;}; // this is the slave servers ip i ran the rndc reload command to check but i dont see the copy in the /etc/named/master/? Any help would be necessary and if you like the layout of my dns, I can provide that too.

  Read the article

• SEAGATE Barracuda 7200.11 HDD not running

  - by Dane411

  After a huge research, I'm stuck at the beggining of getting my HDD data back. Whats happening to me is that in the moment when I plug the power wire to my external 1TB SEAGATE Barracuda 7200.11 ST31000333AS HDD Fw LC15, it makes the sound like it's spinning to almost full speed and then shuts down and spins up again, and so on. It's well known that those HDDs have a bad firmware that someday randomly fails. There are like 2 main problems identified, BSY (busy) state, and LBA0 error. Last time I connected it to power nothing happened, it didnt try to start at all, is it that so called bricked state? I guess my HDDs error is the first one, but I dont really know if what I described is that BSY state or not, neither I know how to check it. How could I know it? Thank you so much!

  Read the article

• how can i realize a video-wall on 3-9pc with vlc

  - by Luca

  hello! i have to create a videowall, from 3 to 9 monitor. every monitor as a pc. actually, i stream from a server 9 movies with different istances of VLC, but i could also play on every machine the relative video with a single player. there's no problem. the real problem is that i really dont know how to sync the videos on a LAN...unfortunately there is a NETSYNC module inside VLC wich is NOT working. here are some info about my setup: videowall from 3 to 9 monitor || from 3 to 9 pc, all with the same configuration || a gigabit router+switch for the "dedicated" LAN im really stuck in this situation, if anyone has an idea or just a completely different solution, please, share it with me! thanks a lot in advance! :)

  Read the article

• Where does the temporary flash file get stored when I am viweing from Firefox

  - by Nishant

  I am watching a lecture and it seems to be adobe flash ...I wanna save this video that I am viewing . The website I am checking is http://cs75.tv/2009/fall/ . I am using Firefox . Dont know if this info helps , but .... My about:cache result is this . Memory cache device Number of entries: 212 Maximum storage size: 13312 KiB Storage in use: 8087 KiB Inactive storage: 6819 KiB List Cache Entries Disk cache device Number of entries: 3224 Maximum storage size: 500000 KiB Storage in use: 26066 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\Cache List Cache Entries Offline cache device Number of entries: 0 Maximum storage size: 512000 KiB Storage in use: 0 KiB Cache Directory: C:\Documents and Settings\nvarm\Local Settings\Application Data\Mozilla\Firefox\Profiles\d74svniy.default\OfflineCache List Cache Entries

  Read the article

• Adding a Windows Server 2012 Essentials server to an existing domain, without migrating the AD

  - by TiernanO

  I have an existing Active Directory in house, a mix between a Win2K8R2 and Win2K3 domain, and i would like to test out Windows Server 2012 Essentials BETA on the network. When walking though the install, it gives me the option of a new domain, or migrating from an existing domain. when clicking existing, it tells me i can only have one SBS server running on a domain at a time... So, i dont have any existing SBS servers in house (both are full standard or enterprise editions) but i do plan on keeping at least one of these extra servers running... So, how do i get a 2012 Essentials server to join a domain, and not migrate the existing domain? or if i do migrate, can i still get one of the other boxes to act as secondary controllers?

  Read the article

• show php error message on IIS 7

  - by Max

  I am using IIS as a webserver on my development machine for PHP webdevelopment. Or at least, I am trying to. When there is a syntax error in a PHP script and I open that file in my webbrowser, I just get an 503 "internal server error" and the default IIS error page for this error. Some browsers dont open that file at all, possibly because of the 503 HTTP Response Header. I would like IIS to act in that case just like the apache webserver: display the PHP file with the error anyway, so that the error message gets printed out. How can this be done? EDIT: PHP settings: display_errors is on and error_reporting is set to E_ALL

  Read the article

• Error loading operating system WinXP Pro

  - by Jakesan

  So im getting the error "Error loading operating system" when the computer tries to boot to a fresh install of WinXP Pro. To get to this point, I: Shrunk the only partition with Gparted to 33GB Copied the partition to the end of the 200GB drive Enlarged the first one to fill the space Formatted the first partition to NTFS Set the first partition to boot, tagged the latter to hidden, removed boot flag This was done all under Hiren's BootCD. Now this is where it goes down the drain. I installed XP Pro SP1a from its CD, and chose to quick format the partition. Now after the OS was installed, I can't start XP without using the default menu action from Hiren's BootCD. All I am greeted with is the "error loading operating system" message. I tried to use the XP recovery to fixboot, fixmbr and bootcfg /rebuild (dont remember if the command was like this, anyway the 3 suggested commands). This did nothing. What am I missing here?

  Read the article

• Secure copy in Linux

  - by Michael

  Hi all, I wanna simpy exchange 3 directories to a collegue's home directory (I dont have write access to that one) from my home directory, probably using secure copy if possible. I am not good with Linux command line, so I am not sure how to do that and I would very much appreciate it if somebody could help me a bit out with this. I guess it should look something like that scp -r /home/user1/directoy1 /home/user2/directoy1 scp -r /home/user1/directoy2 /home/user2/directoy2 scp -r /home/user1/directoy3 /home/user2/directoy3 Do I need to specify the login name of my collegue so that the files can be copied when he enters his password? Thanks for your help, Michael

  Read the article

• Mac Mavericks, ngircd localhost works, private IP doesn't

  - by user221945

  I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

  Read the article

• Need help with an .htaccess URL rewriter

  - by AlexV

  I'm trying to do another SEO system with PHP/.htaccess... I need the following rules to apply: Must catch all URLs that do not end with an extension (www.foo.com -- catch | www.foo.com/catch-me -- catch | www.foo.com/dont-catch.me -- don't catch). Must catch all URLs that end with .php* (.php, .php4...) (thwaw are the exceptions to rule #1). All rules must only apply in some directories and not in their subdirectories (/ and /framework so far). The htaccess must send the typed URL in a GET value so I can work with it in PHP. Any mod-rewrite wizard can help me?

  Read the article

• Different graphic cards drivers while booting from external media

  - by goran

  I am booting a certain system of mine with ubuntu 9.10 from external HDD. I am satisfied with the setup and it works fine, however I would like to modify it so that I can choose which graphic card drivers to load during the boot time. Specifically I would like to choose between: nvidia proprietary driver ati proprietary driver generic driver Currently if I am using proprietary drivers then dont boot into X, delete xorg.conf, start gdm and reconfigure the system using jockey (for hardware drivers). What would be the steps to make this (semi-)automatic and avoid restarting X?

  Read the article

• using iphone to control mac

  - by Ajay Pandey

  i want to use iPhone touch screen as the touchPad for my mac while both devices are connected via bluetooth. So far i hv gone for two approaches what i want is an application which when launched turns the bluetooth on and get connected to mac.Further ...screen of iPhone becomes the touch pad for mac. i dont want to install anything at the mac like any server........ I have already tried the vnc and remotePad approach. the one with vnc looks more promising for me..but even in that case i have to install a vnc server on mac ,i guess and then we'll have to actually call vnc client while my application is still running,which does not look real in 3.2 verson as it does not support multi tasking. Is there any other way of doing it? or is there anything wrong in my above interpretation? please let me know if there is anyother approach of doing the same or if i can do any thing different with my current approach. hoping for quick response Thanks

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >