Search Results

Search found 4585 results on 184 pages for 'signal analysis'.

Page 140/184 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• Unable to run cvlc in a script

  - by VxJasonxV

  I'm creating a script that issues a few curl commands in order to access a time-protected mms stream link, then set up a relay using cvlc (vlc's command line interface) for my own use on an unencumbered player. The curl aspect of this is working, as I can run as a browser and curl side by side and get the same access url. (It's time locked meaning the stream will work forever, but you have to connect quickly or the URL will time out.) The very end of the script prints the command I will run, which is then followed up by "exec $CMD". When I echo $CMD I get: cvlc --sout '#standard{access=http,mux=asf,dst=0.0.0.0:58194}' mms://[...] But the cvlc execution output says: [0x9743d0] main interface error: no suitable interface module [0x962120] main libvlc error: interface "globalhotkeys,none" initialization failed [0x9743d0] dummy interface: using the dummy interface module... [0xb16e30] stream_out_standard stream out error: no mux specified or found by extension [0xb16ad0] main stream output error: stream chain failed for `standard{mux="",access="",dst="'#standard{access=http,mux=asf,dst=0.0.0.0:58194}'"}' [0xb11cd0] main input error: cannot start stream output instance, aborting [0xb11f70] signals interface error: Caught Interrupt signal, exiting... Why is it ignoring my --sout input?

  Read the article

• Are flash drives and hard drives thought of as "an ocean of bytes"?

  - by Jian Lin

  Why can a USB Flash drive be formatted as NTFS or FAT32? Is the USB Flash Drive and Hard Drive just to be thought of as "an ocean of bytes"? I get very used to hearing formatting a hard drive as FAT32 or NTFS, but we can also format a USB Flash drive as NTFS or FAT32? Is it because a hard drive or Flash drive both can be thought of as "an ocean of bits" or "an ocean of bytes"? I remember RAM as: it takes 16 bit or 32 bit as an address signal (the 16 or 32 copper footing on the circuit board), and give out 8 bit of data (the other 8 copper footing on the circuit board). So can a hard drive be thought of as working that way too? So that's why a Flash drive can be the same too? Just an "ocean of bytes". But is it true that hard drive's hardware make it an ocean of sector or something else, that is, the smaller unit of read / write is not byte but something else? So with this "ocean of bytes", NTFS has the format that says, "if the first byte is __, then it means __ (it is a file or folder, and link to which sector, indicated by byte 2 and 3, etc, etc)"

  Read the article

• error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7]

  - by brazorf

  This error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] error is happening after i changed router. Actually, i found out that this error just happens on a ctrl+c signal, so it could be not representative about the error itself. The command i run is very basic: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory Basically, the rsync just stuck there and nothing's happening, until i ctrl+c. After interrupting the process i got the error in subject. I past the whole thing here: rsync -avvvvz --delete /source/path/ username@host:/path/to/direectory cmd=<NULL> machine=HOSTNAME user=username path=/path/to/direectory cmd[0]=ssh cmd[1]=-l cmd[2]=username cmd[3]=HOSTNAME cmd[4]=rsync cmd[5]=--server cmd[6]=-vvvvlogDtprze.iLsf cmd[7]=--delete cmd[8]=. cmd[9]=/path/to/direectory opening connection using: ssh -l username HOSTNAME rsync --server -vvvvlogDtprze.iLsf --delete . /path/to/direectory note: iconv_open("UTF-8", "UTF-8") succeeded. ^C[sender] _exit_cleanup(code=20, file=rsync.c, line=541): entered rsync error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] [sender] _exit_cleanup(code=20, file=rsync.c, line=541): about to call exit(130) The authentication runs on ssh via rsa key. I tried basic troubleshoot such as: ping the remote host ssh -l username remote.host check software firewall logs i asked the remote host sysadmin to check for logs, and when i run that command a ssh connection is actually being established and i can state there is no comunication/authentication/name resolution issue here. Rolling back to old router make this work again. Both client and server are running ubuntu 10.04. Try to take a look at my router configuration, where i'm no experienced at all, but i didnt see any "suspect" (what i was looking for is firewall blocking something) setting. The router itself is DLINK DVA-G3670B. Any suggestion? Thank You F.

  Read the article

• IP queue buffer

  - by summerbulb

  I seem to have an issue with IP queue. I have a linux machine that I am using to run some experiments. The linux machine is configured to be a router, having two NICs, connecting two other computers, and managing their network traffic. All incoming packages are captured, using iptables, and analyzed by a C application. The application analyzing the packets has a built-in delay, as part of the experiment. So I have one very fast computer sending packets through my linux-router and a (relatively) slow linux-router that analyses and deals with the packets, one by one. This situation leads to the fact that when I fire up a sender application on one of the computers connected to the linux-router, my IP queue on the linux-router gets filled up (almost) instantaneously. The IP queue's max length is currently set to 1024, and if it overflows, the packets are dropped. This is expected and i'm OK with it. But, (and this is where it gets interesting), every now and then I get the following error: "Failed to receive netlink message: No buffer space available" At start, I thought this was due to the IP queue overflow, but after some analysis i found that sometimes I get the error even if the IP queue buffer did not overflow, and sometime I DON'T get the message even though the buffer DID overflow. When I run > cat /proc/net/ip_queue, I get the following table (also used to monitor the IP queue overflow): Peer PID : 27389 Copy mode : 2 Copy range : 65535 Queue length : 0 Queue max. length : 1024 Queue dropped : 1166875 Netlink dropped : 2916 Looking at the last two values, Queue dropped seems to refer to packets that did not manage to get into the IP queue because the buffer was full. I can see this value rise as I bombard the linux-router. Netlink dropped ( as it's name implies :) ) seems to have to do with the error i'm getting. I did my best to search for material on this error, but wasn't able to find anything that seemed to point me in the required direction. Bottom line: Why am I getting this error and what can I do to avoid it?

  Read the article

• Recommend a free temperature-monitoring utility for cores + video card, on Vista?

  - by smci

  Looking for your recommendations for a free temperature-monitoring utility, for my PC (Core 2) and graphics card for Vista. (Question reposted with the hyperlinks now I have 10 reputation). I don't want all the geeky details, I don't overclock, I don't see the need to mess with my fan speeds or motherboard settings, I just want something fairly basic to help with basic troubleshooting of intermittent overheats on video card and/or mobo: must run on Windows Vista (yes, don't laugh). ideally displays temperature when minimized to toolbar, and/or: automatically alerts me when temperature on either core or the video card exceeds a threshold ideally measures temperature of video card and system as well, not just the cores. HDD temperature is not necessary I think. logging is nice, graphs are also nice portability to Linux and Mac is nice Apparently Everest is the best paid option, but I'm not prepared to spend $40. I found the following free options, but no head-to-head at-a-glance comparison: CoreTemp (only does cores, not video card?) Open Hardware Monitor (nice graphs, displays when minimized to toolbar, no alerts) RealTemp (has alerts, works minimized, lightweight install) HWMonitor (no alerts, CNET: "[free version is] simple but effective") from CPUID CPUCool (not free: 21-day trialware, then $18) SpeedFan from Almico (too geeky, detail overload; CNET: "most users won't be able to make head or tail of the data this utility provides") Motherboard Monitor (CNET: not recommended, requires expert knowledge of your mobo, dangerous) Intel Thermal Analysis Tool (only does cores, not video card? has logging) Useful discussions I found: hardwarecanucks.com , superuser.com 1, 2 , forums.techarena.in (Update: I downloaded Real Temp 3.60 and it meets all my needs, the customizable alert temperature is great. Open Hardware Monitor seems to be the other one that mostly meets my needs, except no alerts; but it is portable. I tried SpeedFan but the interface is very cluttered, too much unnecessary detail (needs a Basic/Advanced mode and a revamp of the interface.) The answer to my underlying issue is nVidia Geforce LE 7500 video card which runs very hot.)

  Read the article

• PC power supply & normal range for voltages reported in BIOS hardware monitor?

  - by Chris W. Rea

  I'm trying to diagnose whether my computer has an ample power supply. Sometimes when I play a video-intensive game, both monitors lose the video signal, even though the computer remains on and sound playing. A theory I have is: the video card isn't getting sufficient power. I can't imagine it's overheating because the machine is well-ventilated and the video card isn't hot to touch when this happens. Anyway, in my PC's BIOS there's a Hardware Monitor page, and among other voltages reported (such as CPU, DRAM, South Bridge, etc.) I can see the following values: 3.3V 3.152V 5V 4.944V 12V 11.872V Are those the voltages used by peripherals? What voltage should I be referencing if I want to know what my video card (PCI Express) is consuming? What is the normal range of values reported for those? My values above appear to be under by approximately 4.5%, 1.1%, and 1.1% respectively. Is that cause for concern? How else should I be determining if my power supply is "right-sized" for my PC and video card, or am I perhaps barking up the wrong tree?

  Read the article

• Mac mini simple customized, Mac mini server or other?

  - by microspino

  I'm in front of a big IT choice for my little office and I need some advice. We have 5 users, 1 super user, 1 HP500 DesignJet Plotter, other 4 laser printers, 1 HP Fax/Print/Scan/Copy machine. All the clients are XP Sp3 boxes. We would like to: centralize and share 90Gb of files using a Dropbox (this way we will have LAN sync of local working directories + internet backup + access our files wherever we are). centralize our plotter, printers and fax machine backup all the workstations share outlook calendar and tasks run 24x7 saving some energy Of course this setup It's just the first step to a more serious and creative network management of our office, so we are open to new ideas. The budget vary from 400€ to 900€, we are not tech gurus but at least one of us is a power user close to become a geek. I've read some articles on macminicolo about a mac mini either normal or with snow leopard server. I heard about Windows Home Server too on the lifehacker website but I'm in a sort of analysis - paralysis can You help me?

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• Turning on Bluetooth disables wifi on Yoga 2

  - by Yostage

  I have a Lenovo Yoga 2. The moment that I turn on bluetooth, the wifi drops out - I lose connection, and connecting again shows "connection failed". If I turn the bluetooth off, wifi can reestablish fine. I've tried lots of different combinations of drivers for both the wifi and the bluetooth, but no combination has has changed this behavior yet. I've read some speculation that the cards have insufficient shielding, but that seems like kind of a large flaw to ship with. I've tried with a Carbon X1, a Yoga 2 Pro, and a Yoga 2 all next to each other on the desk while running InSSIDer. The X1 and the Y2P don't lose wifi connection when the bluetooth turns on, but the Y2 does immediately. The Y2P and the Y2 are running the same drivers for bluetooth and wifi, and appear to have the same wireless card internally. During the failure state, InSSIDer still sees signal strength for my network, but I cannot connect to it. stats: the card that comes in the laptop is an Intel Wireless-N 7260 Intel Bluetooth driver is at 17.0.1401.422 Intel Wireless driver is at 17.0.2.5 Windows 8.1 x64 Home wifi is a Medialink MWN-WAPR150N

  Read the article

• Server Clustering (Django, Apache, Nginx, Postgres)

  - by system-matrix

  I have a project deployed with django, Apache, Nginx and Postgres. The project has requirement of live data viewable to customers. The projects main points are: 1. Devices in field send data to server(devices are also like website users) after login. 2. There is background import process which imports the uploaded data in postgres. 3. The webusers of the system use this data and can send commands to the devices, which devices read when they login. 4. There are also background analysis routines running on the data. All the above mentioned setup and system is deployed on one amazon EC2 cloud machine. The project currently supports over 600 devices and 400 users. But as the number of devices are increasing with time the performance of the server is going down. We want to extend this project so that it can support more and more devices. My initial thinking is, We will create one more server like current one and divide the devices amongst these to servers. But Again We need a central user and device managment point though django admin. Any Ideas? What are the best possible ways to create a scalable architecture? How can I create a Postgres Cluster and Use it with Django, if possible?

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• Linux wireless disconnect every 20 minutes

  - by james

  My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

  Read the article

• Incorrect durations mp4 file created by ffmpeg (avconv)

  - by Ruslan Sharipov

  Example usage: avconv -i rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af -vcodec copy -an -sn -map 0 -f segment -segment_format mp4 -segment_time 60 -y %05d.mp4 avconv version 0.8.3-6:0.8.3-1+b1, Copyright (c) 2000-2012 the Libav developers built on Jun 15 2012 13:54:35 with gcc 4.7.0 HandShake: client signature does not match! Metadata: height 480.00 remote_addr: sdp_session {sdp_session,0, {sdp_o,"-","1289703354974145","1289703354974145",inet4, "10.1.12.99"}, "Media Presentation", {inet4,"0.0.0.0"}, {0,0}, [{"control","*"},{"range","npt=0.0 start 30400239.52 timeshift_duration 319250.58 timeshift_size 120000.00 width 640.00 [flv @ 0x1d36a40] Estimating duration from bitrate, this may be inaccurate Input #0, flv, from 'rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af': Duration: N/A, start: 0.000000, bitrate: N/A Stream #0.0: Video: h264 (Baseline), yuvj420p, 640x480 [PAR 1:1 DAR 4:3], 1k tbr, 1k tbn, 2k tbc Output #0, segment, to '%05d.mp4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: libx264, yuvj420p, 640x480 [PAR 1:1 DAR 4:3], q=2-31, 1k tbn, 1k tbc Stream mapping: Stream #0:0 -> #0:0 (copy) Press ctrl-c to stop encoding ^Cframe= 9566 fps= 36 q=-1.0 Lsize= -0kB time=318.25 bitrate= -0.0kbits/s video:30348kB audio:0kB global headers:0kB muxing overhead -100.000071% Received signal 2: terminating. Result: serafim@yard:~/video2$ ls 00000.mp4 00001.mp4 00002.mp4 00003.mp4 00004.mp4 00005.mp4 Now try to play the files in the player, such as VLC. And that's what we get: the first fragment (00000.mp4) played well, no problems, but the second (00001.mp4 and beyond) starts the bug manifests itself, namely the file 00001.mp4 first 60 seconds black screen, but since 61 seconds starts playing the video. Attachments: https://dl.dropbox.com/u/760901/rtmp_and_mp4.zip How to get rid of the delay with black screen at the beginning of the segments? Maybe ffmpeg to pass parameters, or third-party software is able to correct the obtained segments mp4?

  Read the article

• Why does my Intel Tolapai network chip not transmit packets?

  - by Hanno Fietz

  I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

  Read the article

• Can I connect a Playstation 3's HDMI output to my monitor's DVI-D input? [migrated]

  - by HankJDoomstorm

  I'm attempting to connect my Playstation 3 to my computer monitor. The monitor has a DVI-D (dual link) input, so before distinguishing between the different DVI varieties, I bought a DVI-I (dual link) to HDMI converter that won't fit into the port on the monitor (not only that, there isn't enough physical space in the back of the monitor to fit that much stuff before it hits the bottom of it). So I grabbed a DVI-D (single link) cable and got a female-to-female DVI-I coupler, and plugged the DVI-D cable into the monitor and the whole mess of converters. The end result was HDMI to DVI-D single link, but my monitor isn't receiving a signal on its digital channel. (For clarity's sake: DVI-D DL input on Monitor, DVI-D SL cable, DVI-I DL female-to-female coupler, DVI-I DL to HDMI converter, HDMI output on PS3) I don't know much about this stuff (obviously), but my educated guess is that the bandwidth of the PS3 is too high for the DVI-D Single Link cable, so nothing's getting through. Will replacing the single link cable with dual link resolve this? If not, is it possible at all? Oh, I should mention I'm aware I won't get audio through the monitor. I have an RCA to 3.5mm converter for that.

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• Control Panel as menu includes a blank item

  - by Matthew Ferreira

  When viewed as a menu attached to the Start Menu in Windows 7 Ultimate x64, the Control Panel contains a blank item. It looks like this: This item cannot be deleted or removed. I also cannot create a shortcut to it. No error message is displayed, instead simply nothing happens. I've tried using Shell Object Editor (using Run as Administrator) to find out if there is an errant entry on the Control Panel, but many entries (almost two dozen) are blank. There are several valid entries as well. I've looked through the registry and through C:\Windows, \system32, and \SysWOW64 but have had no success. I looked at this question, but I am not using Windows XP and thus have no option to use Tweak UI's Rebuild Icons function. Please note that this is no empty entry in the Control Panel when opened normally, only when attached to the Start Menu as a menu. I have compared the list of entries on the attached menu to the normal Control Panel and other than the blank entry, they are exactly the same. Nothing is missing from one or the other. I've also compared the menu and the normal view to reference images and lists of Control Panel items and have found no irregularities. Is anyone familiar with this problem or know of a solution? I've performed virus and malware scans and found nothing. I've used CCleaner with no change. Nothing with Shell Object Editor. Nothing with Registry Editor. Certainly someone here knows how to fix this. My only guess is the many blank entries visible in Shell Object Editor, but I am reluctant to delete that many items without further analysis and guidance. I appreciate your time and consideration.

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• Defragging Host OS of VMWare

  - by JackLocke

  Hi All, I want to ask something that has been puzzling me from last few days. I will try to explain my problem as clear as I can ... I have VMWare Workstation installed in my machine. And I use one separate 100Gb drive which stores all of my virtual machines, nothing else. Now, last week I was playing with a De-fragmentation tool called "Smart Defrag" which showed me in its analysis report that my drive where I am currently storing all of my Virtual Machines has more than 80% of fragmentation !!! Now my question is ... What will be the effect on my Guest / VM machine performance if I defrag my Host machine ... I mean this Host machine is essentially storing those virtual machines, but still dont have any direct access to what ever is stored in those machines ... so defraging the host should not cause any problem. But before proceeding, I want to hear from other people who may have met same problem. I will really appreciate any help ... BTW, I am using Windows 7 as Host and the guest machines I am using are Windows 2008 & 2003 & Ubuntu 10.04 THanks, Jack

  Read the article

• Top cpu% analyis

  - by user111196

  I would like the know in what cpus % can be considered in save range and also load average? Which indication will give signal something is wrong with the server? top - 22:55:51 up 3 days, 6:39, 1 user, load average: 0.53, 0.43, 0.37 Tasks: 229 total, 2 running, 227 sleeping, 0 stopped, 0 zombie Cpu0 : 16.2%us, 0.7%sy, 0.0%ni, 82.8%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu1 : 10.5%us, 0.7%sy, 0.0%ni, 88.5%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu2 : 9.0%us, 0.0%sy, 0.0%ni, 91.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.3%us, 0.3%sy, 0.0%ni, 99.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 1.0%us, 0.0%sy, 0.0%ni, 99.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 44.8%us, 2.6%sy, 0.0%ni, 37.0%id, 0.0%wa, 9.4%hi, 6.2%si, 0.0%st Cpu6 : 3.0%us, 0.0%sy, 0.0%ni, 96.7%id, 0.0%wa, 0.0%hi, 0.4%si, 0.0%st Cpu7 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 16468596k total, 2423908k used, 14044688k free, 200172k buffers

  Read the article

• Value of Itanium or Sparc over x86_64 for Oracle Deployment

  - by Antitribu

  We are looking at a new environment to run our Oracle Database running on SUSE (potentially migrating to RedHat). Our database is approximately 100GB and performs adequately on our current hardware (x86_64) with approximately 6GB of ram allocated to it. We are growing quickly however and will require more performance shortly. Given the cost of Oracle licenses we would like to maximize the value from each license by choosing the most appropriate CPU to run the software on. The questions are: Are there substantial benefits to looking at Itanium or Sparc hardware, are there any drawbacks? Is there a point where one starts to scale out better? What are the long term support options for Itanium? Given the dominance of x86 would it be safer long term to stick with x86? On average what would be the performance benefit of implementing an Oracle database on Itanium or Sparc over x86_64? Is this an issue at all or will other factors (IO/RAM) cap out first? If anyone can point me towards some solid documentation on comparisons between the platforms that provides good case analysis of when to choose which I'm more than happy to accept that as an answer. Edit:- Added Sparc as an Option as it was previously not considered however with the recent Oracle Sun aquisition seems very relevant.

  Read the article

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• Internet Problem: Wireless connected but no connection to internet

  - by Josh K

  Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >