Search Results

Search found 5697 results on 228 pages for 'upgrade advisor'.

Page 140/228 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Recover a lost IBM DS4300 SAN password?

  - by Daniel

  I have a pair of IBM DS4300 SAN units that I need to perform a firmware upgrade on. Unfortunately the admin passwords on these units have been lost and now need to be reset. I had hoped the default password of 'infiniti' would work but it seems that it must have been changed. I know the method here is to contact IBM but the cost of that phone call is ludicrous if someone out here knows what they're going to tell me to do. These units are out of warranty and the cost of support is beyond what we have the budget for. Is there an interrupt I can enter during the boot process (similar to a cisco password recovery) or is there a hardware/software tool I require? Please, if anyone has ever gone through the process of an IBM password recovery I’m asking for a little help. EDIT: Just to clarify, the password I need to reset is the one used for serial cable access and not for storage manager. Sorry if I have caused more confusion.

  Read the article

• Assistance in setting up new APC Smart-UPS RT on a new VMware enviroment

  - by user38085

  I'm new to the realm of setting up a APC Smart-UPS RT 8000VA UPS with a management network card (AP9618). The project calls for the upgrade of the firmware for the network card to the newest and greatest. It also calls for the Powerchute Business Software to be installed with notifications setup per email for temperature, shutdown, and battery low. I know I'll have to use the serial cable to flash the firmware and install the software on one server 2003 box. Also on that server I'll have to install the software and setup the GUI (IP address) interface. Whats confusing the most is the whole process, and steps to use without taking down the network, which would be very bad. In flashing the firmware does it take down the UPS? Do i have to run BOOTP commands to setup the network card? Also no agents will be used on any of the VWware OS's and no SNMP trap will be used.

  Read the article

• Where Debian Lenny stores initial ifconfig values?

  - by Kuroki Kaze

  With upgrade of VMWare Player I suddenly found my Debian Lenny VM not getting IP address. Some DHCP issue maybe, I don't know. So I have to set it manually every boot in Player window, via: ifconfig eth0 down ifconfig eth0 192.168.175.128 netmask 255.255.255.0 up I usually start up VM and then connect to it via SSH, so this procedure bothers me. Sure I can add it to startup script, but is there some special place to enter these values? Like, some config file or so?

  Read the article

• RAIDZ vs RAID1+0

  - by Hiro2k

  Hi guys I just got 4 SSDs for my FreeNAS box. This server is only used to serve a single iSCSI extent to my Citrix XenServer pool and was wondering if I should setup them up in a RAIDZ or a RAID 1+0 configuration. This isn't used for anything in production, just for my test lab so I'm not sure which one is going to be better in this scenario. Will I see a major difference in speed or reliability? Currently the server has three 500GB Western Digital Blue drives and it's dog slow when I deploy a new version of our software on it, hence the upgrade.

  Read the article

• go back to original version of firefox in ubuntu from beta version

  - by Jack Coroman

  In ubuntu 9.04, I tried to upgrade from firefox 3.0 to 3.5, by installing some apt-get packages, and there is a problem! Now firefox calls itself "Namoroka" and the firefox logo is gone and replaced by a black square in the upper bar and it says it is a development beta version. I really don't like this version, how can I go back to the stable version of firefox? I tried apt-get remove firefox-3.5 and apt-get install firefox-3.0 and that did not work. How do I go back to the stable version of firefox?

  Read the article

• SSD for Visual studio : Intel X25-m G2 or OCZ Vertex

  - by meska

  hi, looking for laptop upgrade, and thinking about SSD drive. Laptop would be Dell Studio XPS with T9400 as i can get one for a very good price. So i was thinking about replacing the built in 500 GB hdd with some kind of SDD Currently two choices: OCZ Vertex Series 60 GB vs. Intel X25-M G2 MLC 80 GB Price is almost the same. From anandtech Intel performs badly in sequential write, but scores very high numbers in random write and random read (good for visual studio?) and i get more space. What do you think? OCZ Vertex or Intel X25-M G2 ? Purely from Visual Studio 2008 and upcoming 2010 perspective?

  Read the article

• Automated Deployment of Windows Application

  - by Phillip Roux

  Our development team are looking to automate our application deployment on to multiple servers. We need to control multiple windows servers at once (Stopping Database server & Web Server). We have a ASP.NET project, database upgrade scripts, reports and various Windows services that potentially need to be updated during deployment. Currently we use Jenkins as our CI server to run our unit tests. If something goes wrong in the deployment process, we would like the ability to roll back. What tools are recommended to automate our deployment process?

  Read the article

• Firefox: How do I disable AddOns on my Mac

  - by lexu

  This morning firefox told me it needed to upgrade an addon (noflash) and I told it to go ahead. Now Firefox won't start. How can I prevent Firefox from loading the addons? On a windows site I found the hint to start Firefox in safe mode using Firefox -safe-mode from the command line .. how do I do that on the Mac ... /Applications/Firefox.app is a directory after all. Where are the Firefox config files?

  Read the article

• How to install specific version of MySQL?

  - by user85569

  I installed from the repo, 5.0.77... including setup of PowerDNS (and the backend for MySQL). I tried setting up replication from my Master (which is MySQL 5.1.53) but it didn't work even though there were no errors, nothing got replicated. So the last resort is to try the same MySQL version on both the master and the slave (nb, only the slave has pdns installed) How would I go about installing MySQL 5.1.53? I tried downloading the rpm from MySQL (obviously the wrong one, didn't even include the mysql command to shell into the databases), but in turn fucked up the dependencies for pdns' mysql backend. I have the atomic repo which will install MySQL 5.5 (both on my Master server and Slave), but I don't want to do a major upgrade on the master right now as it's in production. Would love some advice!

  Read the article

• Is there a way to make Apple Mail work well with Exchange server calendar?

  - by Joshua Frank

  My office uses Macs, but most of our clients use Windows and Outlook. Whenever people send invitations from Apple Mail to a Windows/Outlook machine, the invitations are garbled and look nothing like the nicely formatted invitations that Outlook people are used to. We also have no tools to view shared calendars, so we can choose mutually open time slots, and other useful calendar features that Outlook has and Apple Mail seems not to. So is there a plugin or third party program that will give Apple Mail the nice calendar features of Outlook? (By the way, I've looked into actually buying Outlook for Mac, and the pricing is kind of prohibitive, because you MUST buy the whole Office Suite, which we already have, there's no upgrade path, and there's no volume discounting.)

  Read the article

• Can you use a USB hard drive in ESXI?

  - by semi

  I know that you can install ESXi 4.0 on a thumbdrive, but I was wondering if you could plug in an external harddrive to give extra storage to one of your VMs? We run a fileserver inside of ESXi that needs a space upgrade, but we're thinking of migrating to a different fileserver solution and would rather stick to external media to ease the later transition. edit: Ideally I'd like the drive to show up to the VM directly and not have ESXi control it, so that I could move it to a different machine and still have all of the data appear the same.

  Read the article

• Dell PSU Compatibility: Dell Inspiron 530 (Desktop)

  - by ashes999

  I have an Inspiron 530 with a stock PSU. I need to upgrade it to meet my video card's needs (AMD HD6770), which demands at least 450W, to potentially fix BSODs with the latest version of the drivers (so claims AMD support). Now, I've heard conflicting reports about whether Dell uses special/proprietary PSUs. (Examples for aye and nay to special PSUs.) How exactly can I determine if a PSU is compatible with my PC, before buying it? I assume I will not be able to return it if it doesn't fit, or makes my computer explode in a fireball of doom.

  Read the article

• How to fix an SSD

  - by anonymous

  I have a Samsung 128 go SSD : MZ5PA128HMCD-01000. When I'm using it : there is always I/O errors. I tried to secure-erase it. But it is impossible to create a new NTFS (or any filesystem...) partition because I still get I/O errors. I tought maybe upgrading the firmware will solve the problem. Unfortunately, I'm not able to upgrade the firmware with Samsung SSD Magician Tool ... because Magician says there is no Samsung SSD on my computer... Is there a way to make Magician recognize this Samsung MZ5PA128HMCD-01000 SSD? Is another tool available to flash any firmware on a SSD? What should I do to fix this SSD?

  Read the article

• Verifying Time Machine backups

  - by jtimberman

  I'm preparing my system for a Snow Leopard upgrade, and I prepare for the worst case scenario: full reinstall and restore. I would like to verify that my Time Machine backups are valid, and will restore correctly. My Time Machine backups go to a Linux server running Netatalk, and the backups complete successfully. How do I do a test restore to an alternative location, or otherwise verify my data without overwriting any existing files? Do I need to save anything in particular externally to make sure I can access the backups if I have to reinstall from scratch?

  Read the article

• ECC RAM in GA-G33M-DS2R? Or any Gigabyte/G33M motherboard?

  - by Gregory Hoerner

  I'm looking to retire a server which has 12GB of ECC DDR2 RAM. I'd like to upgrade my multi-purpose machine (firewall, file server, VM host for Windows Home Server, etc.) using the RAM from the server. I was just wondering: Has anyone had experience using ECC RAM in a GA-G33M-DS2R motherboard (or any Gigabyte GA-G33M-XXXX motherboard for that matter)? Has anyone had experience using ECC RAM in a motherboard with a G33M chipset. I've searched everywhere and found the attitude positive of ECC memory working in a Non-ECC board, but I would like some specific positive feedback before proceeding tonight. I have to kick the entire house offline, which I don't like to do without good reason :)

  Read the article

• cPAddons version conflict with Wordpress

  - by Joel Alejandro

  I have multiple users on my CentOS 5.7 server with WHM/cPanel, who have installed WordPress 3.2.1, and eventually did a manual update to 3.3.1, from Wordpress itself. Now the version of WP for those users doesn't match th one detected by cPanel, and of course, "Upgrade" doesn't work because the directory can't be cleaned (WP is already working there). I've looked on the .cpaddons folder of each user account, and there's a YAML file there, but I'm not sure how can I touch that file for solving this issue. Is there any way to tell cPanel that those WP installations are in fact, 3.3.1?

  Read the article

• Potential issues to consider when using debootstrap for different Ubuntu distros

  - by BrainCore

  We currently run Lucid on top of Xen. Using debootstrap, we have created many jailed environments for Lucid (10.04), Maverick (10.10) and Natty (11.04). We're considering creating an Oneiric environment as well. However, we're beginning to wonder what the consequences of doing so are. What incompatibilities should we watch out for? The Lucid base runs on the 2.6.32 Kernel, and happens to be running on Amazon EC2 (Xen). We realize that Oneiric when installed from scratch comes with the 3.0 Kernel. Also, if we were to upgrade the Lucid base to Oneiric (including the Kernel), what would we have to watch out for to ensure that the Lucid, Maverick, and Natty jailed environments still work fine?

  Read the article

• Using virt-install to mount multiple cdrom drives/images

  - by Dana the Sane

  I would like to create a windows xp guest from the windows xp upgrade cd I have, along with one of a few full versions I have around. However, when I reach the stage in the installer where I am prompted to insert a full version cd, the installer can't find it, i.e.: Setup could not read the CD you inserted, or the CD is not a valid Windows CD.. Is there a work-around for this?, my Googling didn't uncover anything. I've tried various combinations of mounting .iso files and specifying disks, such as: $sudo virt-install --accelerate --connect qemu:///system -n xpsp1 -r 2048 --disk ./vm/winxp_sp1.iso,device=cdrom --disk ./vm/windows.qcow2,size=12 --vnc --noautoconsole --os-type windows --os-variant winxp --vcpus 2 -c /dev/cdrom --check-cpu If I try to specify multiple cdrom drives, I receive an error: virt-install --accelerate --connect qemu:///system -n xpsp1 -r 2048 --disk ./vm/winxp_sp1.iso,device=cdrom --disk /dev/cdrom,device=cdrom --disk ./vm/windows.qcow2,size=12 --vnc --noautoconsole --os-type windows --os-variant winxp --vcpus 2 --check-cpu Starting install... ERROR IDE CDROM must use 'hdc', but target in use.

  Read the article

• Why would cat6 connectors not work with cat5e patch cable?

  - by Lee Tickett

  I had a naff batch of cat5 connectors (the latching mechanism didn't work) so decided to order in some cat6 connectors in preparation for the inevitable upgrade. My existing reel of for making patch cables is cat5e utp stranded. I made up a few cables and tested them- none of them worked. I recrimped and still nothing. When i check them with a multi-meter not all pins are connected. This reel has always worked with the previous cat5 connectors so I tested the cat6 connectors on a reel of solid cat5e cable and they work fine. Any ideas what I might be doing wrong? Or what might be at fault? (cable/connectors) and how I can diagnose? Thanks Lee

  Read the article

• DVD-RW Drive not recognizing a DVD+R disc

  - by unknown (yahoo)

  Hi everyone, I am having trouble burning DVD+R disc's. My OS is vista and i have used this burner and these same discs in the past. I haven't had the need to do so in months and now that i come back to create some backups my DVD/RW drive doesn't recognize a brand new DVD+R disc. These disc are the same ones i have used in the past(Same Pack even). Anyone have any idea what this might be. Maybe a vista upgrade or something that i downloaded in the last few months that could have thrown something off? Thanks in advance.

  Read the article

• Problem closing MDI child window in Terminal Services/Remote Desktop Connection 7.0

  - by Justin Love

  I have one user whose computer just got updated to the 7.0 Remote Desktop Connection. Concurrently, she has started having a problem closing the MDI child windows in an old FoxPro application running on the remote server. We have two different servers, both 2003, running the same application, one locally and one at a remote office. Only the remote office server is giving trouble. It works fine for me, even when logging into her TS account. No other users have complained. The other day the same user experienced an error message (path not found for a path showing a localization placeholder) starting the RDC, fixed by reboot. I suspect she may have had RDC running during the 7.0 upgrade.

  Read the article

• Transferring FSMO roles over vpn

  - by Tom Bowman

  I have a server located at one of our offices which is quite old and is due to be upgraded soon, this server holds the FSMO roles, I have another server in another office, both are DC's in the same domain and both are replicated, both run Server 2003 standard. I need to transfer the FSMO roles from the old server to the the one I have in the other office before I upgrade. Also I am looking at bringing in Exchange 2010 server however I cant install/configure that until I transfer the roles as it needs to be at the same site as the schema master. My question really is as both servers replicate over a vpn, how quickly will the roles transfer and will there be downtime as I need to make sure that while the transfer is running, both servers will service logon's and share files. or would it be better to do it out of hours? many thanks and apologies if I've missed out anything Regards Tom

  Read the article

• Sending files with iChat doesnt work in Snow Leopard

  - by Nippysaurus

  My girlfriend and I often sit in the lounge looking at stuff online and sending it to each other to look at. So sometimes we drag images into an iChat and it will appear in the other persons iChat window. The ability to do this seems to have broken with the upgrade to 10.6, and the issue persists over both of our laptops and my iMac. The following is a scheenshot of what happens. The image that appears in my window is from me dragging it in there, but the other person cannot see it, and the next bubble is the other person attempting to send me an image, but I only ever see that little white circle for a while then it dissapears. Is this broken for everyone?

  Read the article

• Debian apt dependency mismatch (libc6)

  - by Sean Gordon

  Earlier, I tried to install package via apt-get (cython), but it failed with the Errors were encountered while processing: message, and since then, apt is refusing to install anything. apt-get check output below: root@dix:~# apt-get check Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: libc6 : Depends: libc-bin (= 2.11.3-2) but 2.11.3-4 is installed libc6-dev : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed libc6-i386 : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed E: Unmet dependencies. Try using -f. Apt/aptitude don't seem to be able to fix this dependency issue, and I don't know what to do. Edit: Running apt-get -f install results in no change, and my sources are all squeeze. Running apt-get update then apt-get dist-upgrade show no change either. Edit 2: I went back to try this again in a new terminal and apt-get -f install gives this error: dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) configured to not write apport reports Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Edit 3: Using apt-get clean first, then the previous commands, results in the first error again. Using apt-get -f dist-upgrade gives the below. Reading package lists... Building dependency tree... Reading state information... Correcting dependencies... Done The following packages will be upgraded: apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common at automake base-files bind9 bind9-doc bind9-host bind9utils debian-archive-keyring dnsutils dpkg-dev file host initscripts isc-dhcp-client isc-dhcp-common krb5-multidev libapr1 libbind9-60 libc6 libdns69 libdpkg-perl libexpat1 libexpat1-dev libgc1c2 libgssapi-krb5-2 libgssrpc4 libisc62 libisccc60 libisccfg62 libk5crypto3 libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5-dev libkrb5support0 liblwres60 libmagic1 libmysqlclient16 libnss3-1d libssl-dev libssl0.9.8 libtiff4 libtiff4-dev libtiffxx0c2 libxi6 libxml2 linux-libc-dev lwresd mysql-client-5.1 mysql-common mysql-server mysql-server-5.1 mysql-server-core-5.1 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssh-client openssh-server openssl procps python python-crypto python-minimal sudo sysv-rc sysvinit sysvinit-utils tzdata tzdata-java 75 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 5 not fully installed or removed. Need to get 0 B/79.9 MB of archives. After this operation, 1,411 kB of additional disk space will be used. (Reading database ... 52241 files and directories currently installed.) Preparing to replace libc6 2.11.3-2 (using .../libc6_2.11.3-4_amd64.deb) ... *** stack smashing detected ***: /usr/bin/perl terminated ======= Backtrace: ========= /lib/libc.so.6(__fortify_fail+0x37)[0x7fdaad9b9f87] /lib/libc.so.6(__fortify_fail+0x0)[0x7fdaad9b9f50] /usr/lib/libperl.so.5.10(Perl_yylex+0x5896)[0x7fdaae343346] [0x8e83a0] ======= Memory map: ======== 00400000-00402000 r-xp 00000000 08:01 525338 /usr/bin/perl 00601000-00602000 rw-p 00001000 08:01 525338 /usr/bin/perl 00602000-0091f000 rw-p 00000000 00:00 0 [heap] 7fdaaca54000-7fdaaca6a000 r-xp 00000000 08:01 393818 /lib/libgcc_s.so.1 7fdaaca6a000-7fdaacc69000 ---p 00016000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc69000-7fdaacc6a000 rw-p 00015000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc6a000-7fdaacc6f000 r-xp 00000000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaacc6f000-7fdaace6e000 ---p 00005000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6e000-7fdaace6f000 rw-p 00004000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6f000-7fdaace79000 r-xp 00000000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaace79000-7fdaad078000 ---p 0000a000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad078000-7fdaad079000 rw-p 00009000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad079000-7fdaad07e000 r-xp 00000000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad07e000-7fdaad27d000 ---p 00005000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27d000-7fdaad27e000 rw-p 00004000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27e000-7fdaad299000 r-xp 00000000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad299000-7fdaad498000 ---p 0001b000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad498000-7fdaad49b000 rw-p 0001a000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad49b000-7fdaad49e000 r-xp 00000000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad49e000-7fdaad69e000 ---p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69e000-7fdaad69f000 rw-p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69f000-7fdaad6a7000 r-xp 00000000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad6a7000-7fdaad8a6000 ---p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a6000-7fdaad8a7000 r--p 00007000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a7000-7fdaad8a8000 rw-p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a8000-7fdaad8d6000 rw-p 00000000 00:00 0 7fdaad8d6000-7fdaada2f000 r-xp 00000000 08:01 393822 /lib/libc-2.11.3.so 7fdaada2f000-7fdaadc2e000 ---p 00159000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc2e000-7fdaadc32000 r--p 00158000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc32000-7fdaadc33000 rw-p 0015c000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc33000-7fdaadc38000 rw-p 00000000 00:00 0 7fdaadc38000-7fdaadc4f000 r-xp 00000000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaadc4f000-7fdaade4e000 ---p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4e000-7fdaade4f000 r--p 00016000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4f000-7fdaade50000 rw-p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade50000-7fdaade54000 rw-p 00000000 00:00 0 7fdaade54000-7fdaaded4000 r-xp 00000000 08:01 393826 /lib/libm-2.11.3.so 7fdaaded4000-7fdaae0d4000 ---p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d4000-7fdaae0d5000 r--p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d5000-7fdaae0d6000 rw-p 00081000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d6000-7fdaae0d8000 r-xp 00000000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae0d8000-7fdaae2d8000 ---p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d8000-7fdaae2d9000 r--p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d9000-7fdaae2da000 rw-p 00003000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2da000-7fdaae43f000 r-xp 00000000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae43f000-7fdaae63e000 ---p 00165000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae63e000-7fdaae647000 rw-p 00164000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae647000-7fdaae665000 r-xp 00000000 08:01 393819 /lib/ld-2.11.3.so 7fdaae854000-7fdaae859000 rw-p 00000000 00:00 0 7fdaae862000-7fdaae864000 rw-p 00000000 00:00 0 7fdaae864000-7fdaae865000 r--p 0001d000 08:01 393819 /lib/ld-2.11.3.so 7fdaae865000-7fdaae866000 rw-p 0001e000 08:01 393819 /lib/ld-2.11.3.so 7fdaae866000-7fdaae867000 rw-p 00000000 00:00 0 7fff9616d000-7fff9618e000 rw-p 00000000 00:00 0 [stack] 7fff961ff000-7fff96200000 r-xp 00000000 00:00 0 [vdso] ffffffffff600000-ffffffffff601000 r--p 00000000 00:00 0 [vsyscall] dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb

  Read the article

• Why did my Cisco router hang?

  - by Mike Pennington

  We have a Cisco 1841 in our storage IDF that was originally running a 12.4(1) IP-BASE image; I wanted to upgrade to an advancedservicesk9-mz image, but the flash did not have enough space, so I deleted the running image. Later I tried inserting a larger CF from a Catalyst4500, which crashed the 1841 router (now without a bootable image). Using another 1800 series router, I loaded the 12.4(25g) advancedservicesk9 image and verified the image checksums. I set the confreg to 0x2102 from rommon and booted the new image; however the 1841 now hangs indefinitely after printing the IOS export control banner. I have tried four other images, all with the same results. What is wrong with this router? UPDATE 1: I tried loading images from a FAT16-formatted USB, but this didn't work either. I also tried tftpdnld from rommon, but got a get_mac_address(): Search T_IDPROM_MACADDR (0xc3) failed Illegal MAC address. error and the file would not load.

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >