Search Results

Search found 9235 results on 370 pages for 'social networking'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 141/370 | < Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >

  • Get OWA and ActiveSync working on server using HTTP redirect in IIS 7

    - by eric
    We have two servers on our LAN. One is a Windows 2003 Server domain controller running Exchange 2003. The other is a stand-alone Windows 2008 server running IIS 7. Our company website runs on the IIS 7 (2008) server, so the firewall forwards port 80 to this. How can I get OWA and ActiveSync to work with this setup? And without using SSL. I have tried setting up a website on the IIS 7 box (mail.ourdomain.com) and using HTTP redirect to point to http://mailserver/exchange, but this doesn't work. Do we have to purchase an SSL certificate for this to work?

    Read the article

  • Network card very slow, only on Windows

    - by J Penguin
    This only happens to 1 of my machine, and only when booting into Windows 7. No matter what network card I put in, Windows would default its mode to 10Mbps full duplex. Transfer speed is approximately 1 MB/s. If I set it to 100Mbps, the transfer drops to 100-200K/s. If I set it to 1000Mbps, the connection is lost completely. I've tried swapping in different cards, both PCI-E and PCI. I'v etried update the windows, I've tried reinstalling the drivers... On this very same machine, if I boot into Fedora, it can use the card at its full capacity 1000Mbps transfering 80+ MB/s And all the cards work just fine when plugging into other machines on the same network. I'm very curious. What could be the reason for this? The only different software that this machine has is virtual box with a VPN emulator, but disabling that VPN doesn't seem to do anything. I would like to get this fixed, hopefully, without reinstalling windows _< Will that be possible?

    Read the article

  • management network to a network port for additional ones munin and monit

    - by paolo
    management network to a network port for additional ones munin and monit I want to build a separate Netzwek for server management. I have several network cards a linux / debian / ubuntu with computer. Set both network cards sin in the /etc/network/interfaces. # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 10.0.0.240 netmast 255.255.255.0 network 10.0.0.0 brodacast 10.0.0.255 gateway 10.0.0.254 auto eth1 iface eth1 inet static address 10.0.10.240 netmast 255.255.255.0 network 10.0.10.0 brodacast 10.0.10.255 post-up ip route add 10.0.0.0/24 dev eth0 src 10.0.0.240 table eth0-WAN post-up ip route add default via 10.0.0.254 table eth0-WAN post-up ip route add 10.0.10.0/24 dev eth1 src 10.0.10.240 table eth1-LAN post-up ip route add default via 10.0.10.200 table eth1-LAN post-up ip rule add from 10.0.0.240 table eth0-WAN post-up ip rule add from 10.0.10.240 table eth1-LAN still i adjusted / etc/iproute2/rt_tables and following routes set up in the /etc/network/interfaces I want to have both applications and the network interface separately as munin and monit only on eth1 and not have to eth0. it goes to the reboot but sometimes not always. # Traceroute-i eth1 10.0.10.200 not go what am I doing wrong?

    Read the article

  • GNS3 Cannot ping/resolve DNS record

    - by Eldad Cohen
    I set up an internet lab with GNS3, which has 3 routers, in each node there is a computer directly connected. One of the hosts is a DNS server, Windows 2003 Server. The other one is a Windows XP machine. Ping is good between routers and machines but no ability to ping domain.com record on DNS server 2003. I set a static nat on the router to route all traffic from gateway to the DNS server internal ip address, still no answer for the dns request. Any ideas or thoughts will be most welcome.

    Read the article

  • How to fill in the network line in the ubuntu interfaces config file?

    - by matnagel
    I have to configure an ubuntu hardy server network interface. The service hoster told me that this is the network data for the machine: IP Range: 111.111.200.74 to 111.111.200.78 Netmask: 255.255.255.248 Broadcast: 111.111.200.79 Gateway: 111.111.200.73 Subnet: 111.111.200.72/29 I am only using the first IP address. I will update the /etc/hosts file with 111.111.200.74, but I am still unsure how the /etc/network/interfaces file should be. This is my plan: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 111.111.200.74 netmask 255.255.255.248 network 111.111.200.??? broadcast 111.111.200.79 gateway 111.111.200.73 As you can see I don't know how to build the network line. How would I calculate the data for the network line and what is the result? (I changed the first 2 octets of the subnet, they are not "111.111" in the real setup.)

    Read the article

  • Connecting 2 different subnet masks

    - by Jonathan
    I'm no network genius, but I have managed to get most things running. I get confused about subnets and gateways though. We have an office server connected to around 20 PC's that all communicate fine. We have just gotten a cutting machine that won't connect to our network. The server has DHCP, but that fails on the cutting machine, so I've been trying to set the IP manually. Server details are as follows: IP: 10.1.1.12 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 Internet connection is via the modem which is 10.1.1.1 An office PC is ussually set up through DHCP and has the following settings: IP: 10.1.1.36 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 PRIMARY DNS: 10.1.1.12 Cutting Machine computer has 2 network ports. 1 is specifically for the communication between the PC and the cutting machine. It's details must be as follows: IP: 10.100.100.2 SUBNET: 255.255.255.252 GATEWAY: BLANK The other network port need to connect to the server. I was told that the IP and SUBNET need to be as follows: IP: 10.100.100.1 SUBNET: 255.255.255.252 GATEWAY: ?? How can I connect this port to the server and/or the internet. If anyone can offer assistance, it would really be appreaciated.

    Read the article

  • Wireless connection switches off IP address

    - by Sanjay Gupta
    I have a Lenovo laptop with windows XP and a wireless connection at home. The wireless connection works when initially I switch on the computer. but if I leave it for even 5 minutes, the wireless is gone. Then I have to shut it off and start computer all over again, waiting for 5 minutes. Even if the wireless speed is 48Mbps or better, it gives the message "Renewing IP address" and gets stuck there not moving to the next stage. Other laptop in the household works fine and can be left on. Why does this happen ? I suspect that IP address is the problem and somehow is not registered in all the necessary files.

    Read the article

  • Vlans and subinterfaces

    - by Adeodatus
    I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

    Read the article

  • My wifi internet router connection resets when more devices connected

    - by joeeoj
    The wifi internet router is connected directly to Internet cable. The main Pc is attached to it via LAN cable, while 1 laptop and 3 mobile phones connect to it via wifi. Whenever 2 or more devices connect via wifi, the internet connection breaks after one minute and internet connection resets. I tracked this behaviour for weeks, and came to conclusion: It seems like some 'device 1' got IP then it went to suspend mode. Then 'device 2' connected to router and got the same IP. Then the 'device 1' woke up from suspend mode and tried to use his old IP. The router sees that 2 same IP addresses exists and automatically reset internet connection. Is this possible? Have I tracked the problem correctly and how to solve it? The router is set to lease 100 IP addresses to devices who try to connect. The password is strong and no hacker's device is being connected to my wifi network. Tried changing password and AP's name.

    Read the article

  • Can a Linksys Router be the cause of bad speeds on a 1.5 mbps link.

    - by gramware
    We use a Linksys 5-port router at a smal organization with about 20 employees. We recently acquired a 1.5 mbps fibre link, but sometimes the link goes down and speeds are still low. On enquirey from the ISP, this was part of the response, However there maybe throttling due to the router in place. A Linksys is a low end router and may be unable to carried traffic of up to 1536Kbps. We are in a position to deploy a Cisco 871 router on test for 2 wks to eliminate that possibility. Also kindly advise the destination of the ping results they look to high. How true is that about the router throttling the network and need for a bigger one.

    Read the article

  • Which equipments should I buy for a laboratory?

    - by Hossein Margani
    Hi every body! I want to create a network of computers for a network laboratory in a university. I want to install windows on them. What is the fastest way for doing this and also which equipments I should buy for this laboratory. I also want to use this network as a computer laboratory, operating system laboratory, programming laboratory, microprocessor laboratory, computer architecture laboratory and software engineering laboratory. I should emphasis that this is a scholastic laboratory. Thanks.

    Read the article

  • How to connect a Bluetooth network connection using the command line

    - by Ed Guiness
    I can enable a Local Area Network interface for my machine with the command netsh interface set interface "Local Area Connection" ENABLED Is there an equivalent command to connect a bluetooth network connection? I've tried netsh interface set interface "Bluetooth" ENABLED but it seems to have no effect, the connection remains disconnected. I also tried netsh interface set interface "Bluetooth" connect=CONNECTED but this returns One or more essential parameters not specified I know this Bluetooth connection is otherwise ok since I am able to connect using Control Panel Network Connections, right-clicking on Bluetooth Connect.

    Read the article

  • Basic questions about network topologies

    - by laoshanlung
    I have just started learning about network topologies, but there are a lot of confusion about different types of network topologies i have learnt so far. First of all, BUS topology. If i have like 100 PCs in the same wire connected using BUS topology, and the network connection speed is 100Mbps, then each PC will have a connection of 1Mbps, right ? With the same scenario, if i connect those 100 PCs using STAR topology, then each PC will have a connection of 100Mbps ? Then with the TREE topology, i divide the system into 10 sub-system (10 tree branches) , each branch has 10 PCs, then i will have other 10 small "BUS-topology" networks each one will have a connection of 10Mbps and therefore each PC will also have 10Mbps ? And the last one is RING topology, 100 PCs, each PC will have 100Mbps connection ?

    Read the article

  • How to I sync my windows mobile phone via wireless network

    - by Kibbee
    According to this article, I should be able to sync my Windows Mobile smartphone via my wireless internet connection. However, when I go to the connection settings, I only see USB and COM1 options. No option for ethernet. I have an HTC Maple (aka Snap), and it connects fine to my home wireless network, but I would like to be able to sync over the network.

    Read the article

  • Correct way of bringing network interface down in linux

    - by Karolis T.
    For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • I want to add a Quality Assurance domain. How do I handle DNS servers?

    - by Tim
    I'm advising a large client on how to isolate their dev and testing from their production. They already have one domain, lets say xyz.net with the active directory domain as "XYZ01". I want to add second domain say QAxyz.net and make its active directory domain "QA01" All development and QA servers would be moved to the QAxyz.net domain, the machines would be part of the QA01 domain. Note: Some of these servers will have the same name as the production servers for testing purposes. I believe we would have separate DNS servers for each domain. If I am logged into the QA01 domain, to access the production domain I would qualify my access like so: \PRODSERVER.xyz.net login: XYZ01\username Do I need to add a forwarder to my QAxyz.net DNS server so that it can see xyz.net? Would I need to do the same to the xyz.net DNS server to see QAxyz.net? I don't know how to advise them in this. Does anyone have any other recommendations to isolationg a QA domain? Many Thanks in advance! Tim

    Read the article

  • Simulating a low-bandwidth, high-latency network connection on Linux

    - by Justin L.
    I'd like to simulate a high-latency, low-bandwidth network connection on my Linux machine. Limiting bandwidth has been discussed before, e.g. here, but I can't find any posts which address limiting both bandwidth and latency. I can get either high latency or low bandwidth using tc. But I haven't been able to combine these into a single connection. In particular, the example rate control script here doesn't work for me: # tc qdisc add dev lo root handle 1:0 netem delay 100ms # tc qdisc add dev lo parent 1:1 handle 10: tbf rate 256kbit buffer 1600 limit 3000 RTNETLINK answers: Operation not supported How can I create a low-bandwidth, high-latency connection, using tc or any other readily-available tool?

    Read the article

  • Setting up dual NICs under Server 2008

    - by Randall Sexton
    Hi, I'm trying to determine how to set up dual NICs on my Server 2008 box (not R2). I want all web traffic on one NIC and all Hyper-V traffic on the other. Is this possible? ( I assume that it is ) How is this done? ( A link to a tutorial you know of would be great ) Both NICs are the same (Intel PRO/1000 EB Network Connection with I/O Acceleration). Thanks in advance, Randall

    Read the article

  • SSH access from outside to a pc inside network

    - by Raja
    I have a static IP and ADSL router linked to a linksys wireless router to which all my machines are connected. I would want to setup SVN on one of machines and provide SSH access which should be accessible by users outside my network. Would this be possible? Even just SVN access through web should be fine. Please let me know what all things should be done to achieve this ? I have Ubuntu VM running in a iMac Leopard machine and another 2 Win 7 32/64 bit machines. I can setup standalone Ubuntu or Win XP on another machine. Thanks, Raja.

    Read the article

  • CentOS/Apache killing connections

    - by fin1te
    Getting a really strange error. Basically, whenever I browse to my server (http://[ip_address] or http://[hostname]), it doesn't load, and my active SSH connection drops out. I installed CentOS 5.5, and then httpd and PHP 5.3. No other applications where installed, so I can't imagine it's something else causing it. I also reinstalled CentOS 5.5 again, completely fresh, the only thing I did to it was yum install httpd, and it still caused this issue. I've changed nothing in the config or anything else. Driving me mad, has anyone heard of this? It's really frustrating since everytime I attempt to debug this issue, I get kicked off SSH and have to log back in. Theres nothing in the Apache error logs, and nothing in the access log recording my attempt. Also, the result from uname - Linux [hostname] 2.6.35.4-rscloud #8 SMP Mon Sep 20 15:54:33 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux Thank you

    Read the article

  • Block P2P traffic on a Linksys router WRT54G with Tomato firmware

    - by Kami
    I'm running a small wireless network (6 to 10 users) on a Linksys WRT54G with Tomato firmware sharing an Internet connection. I don't want the users to download files with BitTorrent (mainly used) and other P2P apps. I've also found some solutions about lowering P2P traffic priority using QoS. I really need to ban P2P traffic. Does anyone know how to setup some rules to deny that kind of traffic? I've tried to setup an Access Restriction Rule: However it's not working at all.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >