Search Results

Search found 4068 results on 163 pages for 'intel gma'.

Page 142/163 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• How to set up RAID-0 first time on new PC?

  - by jasondavis

  I have built basic PC's in the past but have never used a RAID array at all. SO now I am buying parts to build my new PC, it will be an intel i7 processor. My motherboard will have RAID support which I will use instead of an aftermarket raid controller for now. Also I plan to use 2 SSD drives in RAID-0 for my windows 7 OS. (Please note that I am aware of the issues with doing this, including lack of TRIM support when using RAID with SSD drives. I am OK with it not working as I can just re[place the drives in a year or so or wheneer they become more sluggish). SO here is my question part. If I assemble the motherboard, PSU, processor, RAM, vidm card, etc and then go to turn the PC on, it will have the 2 SSD drives hooked up. so I assume I will then soon the BIOS screen before I install windows? How to I go about making the 2 drives work in RAID-0 at this point? I do the raid part before installing my OS right? Please help with the steps involved from assembling the parts of the PC and then turning it on, to the part of getting the RAID-0 set up between the 2 drives and then installing my windows 7 OS from a Optical drive? Please help, all advice, instructions, tips appreciated as long as on topic. I do not need to be told that this is a bad idea as far as if 1 drive fails I losse it all, I plan on having a disk IMAGE to be able to restore my OS and software to a new set of drives at anytime needed in the event of drive failure. Same goes for lack of TRIM support. Thanks for reading and help =)

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• Is it possible to have DisplayLink USB display hotplugging with Xorg 1.13 on kernel 3.4?

  - by lkraav

  keithp seems to be the only one on the interwebs to have written anything about the subject and he worked with 3.5_rc. I don't want to go above 3.4 at the moment for various stability reasons and am trying to see whether I can get this to work. Xorg 1.13 recognizes the display on connection, "udl" module is loaded, xorg-video-modesetting driver also loads, display lights up. So everything seems to be good. I emerged xrandr-9999 (not many changes on top of 1.3.5): $ xrandr --listproviders Providers: number : 2 Provider 0: id: 69 cap: 0x0 crtcs: 2 outputs: 4 associated providers: 0 name:Intel Provider 1: id: 338 cap: 0x0 crtcs: 1 outputs: 1 associated providers: 0 name:modesetting But I can't get any further, just like this guy: $ xrandr --setprovideroutputsource 338 69 X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 139 (RANDR) Minor opcode of failed request: 35 () Value in failed request: 0x152 Serial number of failed request: 11 Current serial number in output stream: 12 $ xrandr --setprovideroutputsource 1 0 X Error of failed request: 148 Major opcode of failed request: 139 (RANDR) Minor opcode of failed request: 35 () Serial number of failed request: 11 Current serial number in output stream: 12 Any thoughts?

  Read the article

• How can I make XAnalogTV fill my screen?

  - by Breakthrough

  I recently installed xscreensaver, as well as the additional/extra screensavers. Many of the OpenGL ones function correctly, going fullscreen as expected. However, for some reason, the XAnalogTV screensaver leaves two "blank" spots on the edges of my screen. If I manually launch XAnalogTV, it displays a window, which it fills correctly. When I maximize the window, the same effect occurs: the window maximizes, but the two edges of the screen are literally "transparent". This effect also occurs when the screensaver is set to fullscreen. For these reasons, I believe the problem may be related to the aspect ratio of the screen. The edges of the screen are literally "ignored", with nothing being drawn there. Specifically, note the transition between the maximized and full-screen screenshots (with the un-drawn whitespace shrinking as the vertical height has been increased). For reference, I am running Xubuntu 12.04 on a Dell Vostro 1520 (Intel P8600, Nvidia 9300M) with a 1440 x 900 display (16:10). I have also set the GetViewPortIsFullOfLies preference to true. Is there any way to force XAnalogTV to fill my entire screen? Relevant screenshots (windowed, maximized, and full-screen, respectively):

  Read the article

• Centos Server/MySQL server problem

  - by Jake

  Hello all, I currently run a website we get about 15,000-20,000 hits a day. We currently run a very active forum, that is hosted using Vbulletin software. We have 4.5 Million Posts, 80,000 Threads, with about 11,000 members of which just under a third is active all the time. Now I am running a Intel Xeon Quad Core (2.13Ghz) with 4GB of RAM, Centos 5.5 and running DirectAdmin on the box to manage it. I also run the current stable version of Apache, MySQL, and php. This is the only site that is hosted on this machine. Now during random times of day sometimes when it gets busy the server load can get to like 20, but this can also happen when we only have like 200 users active too. I dont understand what is causing these problems. Sometimes I get pages that can generate in .2 seconds other times it takes like 5-8 seconds. I have customized the my.cnf file and that has not helped out anything, I didnt know where else to turn so if anyone has any suggestions please let me know. Thank You In advance.

  Read the article

• iMac 20inch (Mid 2007) SL DVD Boot Prohibitory Sign

  - by Caitlann Lloyd

  iMac 20inch (Mid 2007 Build) with Ubuntu 12.0.4 How I got in this situation I had a perfectly healthy Intel iMac running Snow Leopard several months ago. Then I got the dreaded spinning gear and several kernel panics. After getting a little frustrated (failing to find a solution online), I found an old macbook installation disk and used it to access Disk Utility. From here, I erased my entire hard drive leaving me with no OS. I then created a Ubuntu DVD and installed Ubuntu onto the system. Now, on Ubuntu, I wine installed Transmac and burned a Single layer copy (with languages, etc. removed to save space) of Snow Leopard onto a 4.7GB DVD. I tried to boot from it and was met with first the grey apple screen and a spinning cog before the grey apple shortly turned into the infamous prohibitory sign. Note: I met this problem previously when using Disk Utility to create a bootable USB of Snow Leopard, hence I severely doubt it has anything to do with the DVD created. Resources at my disposal 1 x iMac running Ubuntu 6 x 4.7GB DVDs 1 x USB Stick 12GB 1 x Windows 7 Laptop Resources I do not have Firewire cables Access to a prebuilt retail disk (Misplaced) Access to another Mac Apple Warranty I would be hugely grateful if someone was able to tell me how to install Snow Leopard again.

  Read the article

• My client's solution of a Windows SBS 2011 VM on an Ubuntu host and VirtualBox is pinning the host CPU

  - by Scott Stamp

  Here's my situation, I've got a client hosting two servers (one VM), with the host providing VMware Zimbra, the other Windows Small Business Server 2011. Unfortunately, the person before me had configured this setup as follows. Host: Ubuntu Desktop Edition 10.04 (I know, again, not my choice) running VMware Zimbra 8GB of RAM On-board RAID1 of two 320GB Seagate Barracuda drives for the OS Software RAID5 of four 500GB WD Caviar Black drives on MDADM for bulk storage (sorry, I don't know the model #) A relatively competent quad-core Intel Core i7 CPU from the Nehalem architecture (not suspicious of this as the bottleneck) Guest: Windows Small Business Server 2011 4GB of RAM Host-equivalent CPU allocation VDI file for OS hosted on the on-board RAID, VDI file for storage hosted on the on-board RAID For some reason when running, the VM locks up when sitting nearly idle, and the VirtualBox process reports values of 240%+ in top (how is that even possible?!). Anyone have any ideas or suggestions? I'm totally stumped on this one. Happy to provide whatever logs you'd like to take a look at. Ideally I'd drop VirtualBox and provision this with VMware Workstation, but the client has objected to the (very nominal) costs involved. If hardware needs to be purchased to help, it will be, but we're considering upgrades a last-resort at this time. Thanks in advance! *fingers crossed*

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• Requesting better explanation for expires headers

  - by syn4k

  I have successfully implemented expires headers however, for several days I have been stumped by one thing. This article: http://www.tipsandtricks-hq.com/how-to-add-far-future-expires-headers-to-your-wordpress-site-1533 states Keep in mind that when you use expires header the files are cached in the browser until it expires so do not use this on files that changes frequently. Other sites indicate the same in my reading. But this doesn't seem to be true. I have updated an image, using the same name, several times. Each time I update and refresh my browser, the new image (with the same name) displays. I understand from this article that the old image should display unless I use a new name. Do you happen to know where the misunderstanding is? I have verified that the image in question has expires headers set on it: Request Headers: Host domain.com User-Agent Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.28) Gecko/20120306 Firefox/3.6.28 FirePHP/0.5 Accept image/png,image/*;q=0.8,*/*;q=0.5 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 115 Connection keep-alive Referer http://domain.com/index.php Cookie __utma=1.61479883.1332439113.1332783348.1332796726.4; __utmz=1.1332439113.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none);PHPSESSID=lv2hun9klt2nhrdkdbqt8abug7; __utmb=1.33.10.1332796726; __utmc=1; ck_authorized=true x-insight activate If-Modified-Since Mon, 26 Mar 2012 21:55:33 GMT Cache-Control max-age=0 Response Headers: Date Mon, 26 Mar 2012 22:06:50 GMT Server Apache/2.2.3 (CentOS) Connection close Expires Wed, 25 Apr 2012 22:06:50 GMT Cache-Control max-age=2592000

  Read the article

• Missing MB on a GPT partioned SSD

  - by pisswillis

  I recently installed Arch Linux on an Intel 40GB SSD. I used GPT for partioning (via GNU parted) and created the following partions: /dev/sda1 : 1 MB, no FS, flag=bios_grub /dev/sda2 : 30MB, /boot, ext2, flag=boot /dev/sda3 : 20GB, /home, ext4 /dev/sda4 : ~20GB, /, ext4 After struggling to install grub2 from the livecd environment (which I finally did via grub-install /dev/sda --root-directory=/mnt/ --no-floppy --force) I got a working system. However, when I was inspecting disk usage with df I noticed that my home partition had around 170MB of used space on it. This surprised me because the only things on /home were one users .bashrc, .bash_history, and .lesshst. du confirmed that there was only a few KB of space being used on /home. Why does df report approximately 170MB being used when du does not? Is this space "gone forever", or can I regain it by repartioning and/or reinstalling? When I installed grub2 it said something along the lines of "your embed area is too small", and that I could "use BLOCKLISTS, but BLOCKLISTS are UNRELIABLE". In the end the only way I could get a system booting from the SSD was to use blocklists via the grub-install --force flag. Is this related to the mysterious missing 170MB? Thanks

  Read the article

• How can I determine what is killing my network adapter win7 or vista?

  - by datatoo

  I thought this issue was like another person here, and that downloading the nvidia chipset drivers was the solution. However that is not all that is going on. This machine had Vista 64bit and is now Win7. Same issue with both. I have explicitly been denying network driver updates since getting things working again and when a Windows updates occurs on seemingly benign Office updates the adapter fails to work. Is the update process somehow protecting this machine by turning off things and it fails to recover connectivity after a restart? All that seems to ever work is a system restore. Which does work. Since there are 25 pending updates asking to do there thing, I hate to think this is a one by one update test to find the culprit. Any ideas? This has an integrated nic, video, and I guess audio on the motherboard. ES5200 intel cpu on a gateway 4800-05e I am not quite sure how to determine the actual network adapter. This is a wired adapter. I suppose worst case I can try another adapter if this keeps happening.

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Keeping Xv Overlay configuration throughout an X session.

  - by kriss

  After upgrading my Linux system from Ubuntu 9.04 to Ubuntu 10.10, I suceeded correcting most problems (all related to Intel 82865G Integrated Graphics Adapter support and compiz is still not working but that's another matter) but for one I only have a partial solution. Whenever I play a video the colors are much too saturated. This is really a problem for tones of skins that appears reddish (everyone seems to be coming back from a ski vacation with deep sun burns). As this effect only occurs with videos, not with pictures, I finally figured out it was related to Video Overlays configuration and I can correct it typing: xvattr -a XV_SATURATION -v 120 This change the default saturation value, which is 500 and much too high in my case, at eye sight the correct value seems to be between 100 and 150. Now my problem is that I have to type the above command each time I run a video. If I type it before running the video it has no effect, if I close the video and open a new one, I have to type it again, etc. I tried to put it in Xsession and (logically) it has no effect either. How could I do to get the correct setting whenever I run a video without typing the above command every time ?

  Read the article

• ssd firmware, linux: updating large batch of drives

  - by wryfi

  I was recently hit with a fatal firmware bug that affected dozens of Crucial SSDs deployed in my datacenter. Many of the affected machines use LSI or other proprietary SAS controllers, which Crucial's bootable ISO does not recognize. None of the affected machines has a Windows license. The story is roughly similar for other SSD mfrs, including Samsung and Intel. To resolve this issue, I was forced to stop each machine, remove the affected SSD, remove the SSD from its hotswap caddy, install it temporarily into my ThinkPad, flash the firmware, reverse, rinse, repeat. It took the better part of a day to get through all the affected devices. I am looking for hardware, software, and/or purchasing strategies to ease this pain, as SSD firmware bugs seem inevitable, and our SSD footprint is growing. My first thought is to get a laptop with eSATA and one of these cables (http://www.newegg.com/Product/Product.aspx?Item=N82E16812311004). That should at least make it so I don't have to remove the drives from their caddies. Surely others have run into this. Any novel solutions?

  Read the article

• Kindly guide me to buy a new laptop [on hold]

  - by Its me 007

  I am from India. I want to buy a new laptop. Shortlisted few but confused between which processor,Chip set and Graphics will be the best suited for my requirements. NOTE: NOT ABLE TO POST THE LINKS YOU WILL HAVE TO COPY PASTE IT. SORRY. 1) HP Pavilion 15-N004TX - 4th Gen CI5 - 4200U/4GB RAM/500 GB HDD/ 1GB Radeon Graphic - Rs 39990 www.homeshop18.com/hp-pavilion-15-n004tx-laptop-4th-gen-intel-core-i5-4200u-4gb-500gb-15-6-linux-silver-black/computers-tablets/laptops/product:30989197/cid:16317/ 2) Lenovo Essential G510 (59-398452) - 4th Gen Ci5 4200M/ 4GB/ 500 GB/Win8/2GB Graph ATI Sunpro 8570 - Rs 44969 www.flipkart.com/lenovo-essential-g510-59-398452-laptop-4th-gen-ci5-4gb-500gb-win8-2gb-graph/p/itmdp26eprwf5k5v?gclid=CMnh99GA2LoCFaRU4godNiUAGQ&semcmpid=sem_7847244212_laptopsnew_goog&tgi=sem%2C1%2CG%2C7847244212%2Cg%2Csearch%2C%2C24387103114%2C1t1%2Cb%2C%2Blenovo+%2Bg510%2F59+%2B398452%2Cc%2C%2C%2C%2C%2C%2C%2C2 3) HP Pavilion G6-2303TX Laptop (3rd Gen Ci5 3230M/ 4GB/ 500GB/ DOS/ 1GB Graph) - Rs 40500 www.flipkart.com/hp-pavilion-g6-2303tx-laptop-3rd-gen-ci5-4gb-500gb-dos-1gb-graph/p/itmdm6yzh4gr4cxd?pid=COMDM6YHWMGDRDEZ&ref=1d2b85fc-a03d-4c7d-844b-ec9e8dc95a81 4) HP Pavilion 15-E039TX Laptop (3rd Gen Ci5 3230M/ 4GB/ 1TB/ Win8/ 2GB Graph) - Rs 46690 www.flipkart.com/hp-pavilion-15-e039tx-laptop-3rd-gen-ci5-4gb-1tb-win8-2gb-graph/p/itmdn4d9wykhdcpz?pid=COMDN4CZGFMGJNTN&ref=1d2b85fc-a03d-4c7d-844b-ec9e8dc95a81 Now I am confused between: Which Processor and chipset is best? How much graphic card is enough? (Not a gamer) Is any of this laptop future proof i.e. it should at least support upcoming latest programming softwares which eats more processor and memory. Laptop will be mainly used for multiprocessing.It should be at least capable for following: Visual Studio 2012 and the upcoming versions for at least 4 years SQL server 2008 R2 and above Sharepoint Blend Photoshop Kindly suggest. If anyone know any good laptop with good configuration in the 50k budget kindly suggest. Thanks in advance.

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• Supermicro X8SIL-F with Enermax Modu82+ 625W PSU booting issue

  - by Richard Whitman

  I am assembling a custom PC. The configuration is below: Motherboard: Supermicro X8SIL-F Processor: Intel Xeon 3430 Power Supply: Enermax Modu82+ 625W. Memory: Kingston KVR1333D3LQ8R9S/8GEC 8GBx1 installed in DimmA1 This power switch: Frozen CPU switch When I turn on the PSU, the motherboard tries to start itself before I even push the power switch. The following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and this time it rotates for about 3-4 seconds before stopping. If I pull out the Power switch, and turn on the PSU, again the MB turns on itself and the following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and the system boots properly I am sure there is nothing wrong with any of the components, because I have two sets of identical components (2 MBs, 2 CPUs, 2 PSUs, 2 switches and so on). And both of the systems show the same symptoms. Why is the MB booting up by itself? Why does it fail to boot when the Power Switch is installed? Is something wrong with the type of Power Switch I am using? PS: the power switch is installed correctly, I have double checked the MB manual to make sure its connecting the right pins.

  Read the article

• UPS power requirements for server

  - by captainentropy

  Greetings! So, I just placed an order for a new server. The company recommended that I get a 3000W UPS. (!) As best as I could I calculated the following wattage consumption based on benchmarked data or datasheets provided by the manufacturers of each component: number watts **total watts** MoBo 1 240 240 CPUs (E5540) 2 80 160 RAID cards (3ware) 2 18 36 RAM (6x4GB) 6 3 18 DVD drive 1 7 7 floppy 1 2 2 RE4 drives 8 7 56 WD20 drives 8 6 48 Intel X25 SSD 2 0.15 0.3 total = 567 So that is for the PSU requirements only. The PSUs in the machine are a 720W for the master node and 800W each for two subsystems. That's a total of 2320W that can be delivered by these PSUs. But that is 4X the amount being consumed, at most, by the components. I didn't count case fans or the eSATA card (3W maybe?) or what the PSUs themselves require but assuming I double or triple my calculations I'm not even remotely close to the 3000W UPS I was suggested to get. They run at least $1100. I could get a 2000W for about $750 or a 1500W for $450 and still be well over my estimated power need. I don't think I need a whole lot of run time in the case of a power outage, maybe 20 minutes max, enough time to shutdown if the power doesn't come on within 5-10 minutes. Any thoughts? Am I off on my calculations? Did I overlook something major? If so what are your suggestions for a UPS? Thanks!

  Read the article

• 10 GigE interfaces limits single connection throughput to 1 Gb on a ProCurve 4208vl

  - by wazoox

  The setup is as follow : 3 Linux servers with Intel CX4 10 GigE controllers and an X-Serve with a Myricom 10 GigE CX4 controller are connected to a ProCurve 4208vl switch, with a myriad of other machines connected through good ol' 1000 base-T. The interfaces are actually set up as 10 Gig, according to both the switch monitoring interface and the servers (ethtool, etc). However a single connection between two 10 GigE equipped machines through the switch is limited to exactly 1Gb. If I connect two of the 10 GigE machines directly with a CX4 cable, netperf reports the link bandwidth as 9000 Mb/s. NFS achieves about 550 MB/s transfers. But when I'm using the switch, the connection tops at 950 Mb/s through netperf and 110 MB/s with NFS. When I open several connections from 3 of the machines to the 4th, I get 350 MB/s of NFS transfer speed. So each individual 10 GigE ports actually can reach much more than 1 Gb, but individual connections are strictly limited to 1 Gb. Conclusion : the 10 GigE connection through the switch behaves exactly like a trunk of 10 1 Gb connections. That doesn't make any sense to me, unless HP planned these ports only for cascading switches or strictly for many-clients-to-single-server connection. Unfortunately this is NOT the envisioned setup, we need big throughput from machine to machine. Is this a not-so-known (or carefully hidden...) limitation of this type of switch? Should I suggest seppuku to the HP representative? Does anyone have any idea on how to enable a proper behaviour ? I upgraded for an hefty price from bonded 1Gb links to 10 GigE and see exactly ZERO gain! That's absolutely unacceptable.

  Read the article

• Good references to know why has my computers stopped responding me

  - by Peterstone

  Hello all! I´m a windows xp user (but not for much time...) and I usually see how my computer stop of responding me. The process is this: Firsly it became totally stopped or very slow for certain periods of 5 minutes. How could I do? After that it gets stopped (Even not totally because If I click on the bar I see a blinking response in the bar botton of the program I click on. It´s could be anything related with security (like the firewall or some virus)? Computer university: I usually experience this, using Matlab (R2007a) with System Generator (its respective compatible version) My personal laptop: It´s usually works well but when stopped periods became to appears I know in not much time it will became totally stopped. I usually see how Word 2007 get stopped and after a while my windows xp gets stopped. (well I can access to the the manage task pressing ctr+alt and...). The only solution I see is to kill program by program... My petition: Please, I need good references that help me how to think in order to avoid or to manage the problems previously described. Does anyone know usefull books or articles? EDIT: Laptop: OS: XP Home Edition Version 2002 SP3 Hardware: HP Mini Intel(R)Atom(TM) CPU N270 @1,60GHz 1.99 GB RAM University Computer: OS: XP Profesional SP3 Hardware: AMD Athlon(tm) XP 1800+ 1.54 GHz, 768 MB RAM

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Applications randomly alt-tab? (especially full screen games)

  - by Henry Scotts

  I'm not sure when this began, how it happens, or why it happens, but it is quite bothersome and apparently random. Just randomly throughout the day my computer will just go to the desktop. I could be in a full screen game and it will just immediately alt tab and present the desktop. Or I could be watching a movie and this happens. Sometimes it happens once every three hours and other times (just today actually) it did it twice in the span of 30 seconds. I am positive I am not pressing a hotkey because I launched a game, sat idle, and noticed it alt tab while cleaning up around my room after about 20 minutes. Sometimes it goes days without this happening. Specs: Windows 7 Ultimate 64 Bit, 10 gigs of RAM, GeForce GTX 260, Intel Xeon CPU. I also have basically nothing running when it happens other than the game and FireFox. My FireFox add-ons: Adblock Plus, Download Statusbar, Firebug, FirePHP, lazarus form recovery, tree-style-tabs, yslow. I doubt FireFox is causing the issue but I figured I'd include it anyway because it is the only application I have running when it happens. As for user processes I have running: VCDDaemon (context menu for virtual clone drive), razerhid (mouse), OSD, taskhost, dmw (desktop window manager), anyfullscreengame, audiorepeater, netsession_win, explorer, razerofa, tsvncache, firefox, plugin-container, and EKIJ5000MUI (printer). Whew. Okay. That was a lot of information. If someone could diagnose this I would be most grateful for this has been around with me for years.. Thanks for reading! PS: I doubt it's a virus because I never download illegal software and pretty much only browse Reddit and Stackexchange and play games. If it was a virus it would be a pretty lame one.. Hah..

  Read the article

• How important is dual-gigabit lan for a super user's home NAS?

  - by Andrew

  Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

  Read the article

• OpenVZ vs KVM for Linux VMs

  - by Eliasdx

  Hardware: Intel® Core™ i7-920, 12 GB DDR3 RAM, 2 x 1500 GB SATA-II HDD (no SoftRaid because Proxmox developers don't support softraid and they are sure you'll run into problems) Software: Proxmox VE with KVM and OpenVZ support and debian everywhere I want to run multiple Linux VMs on this server. One for a firewall (I want to try pfSense), one for MySQL, one VM for nginx (my stuff) and ~2 VMs with nginx for other people's web sites. I don't think that pfSense will run in an OpenVZ environment but it should run in KVM. The question is if I should setup the other VMs using KVM or OpenVZ. In OpenVZ they should have less overhead for the OS itself but I don't know about the performance. I heard that KVM is more stable but needs more RAM and CPU. I found this diagram showing a OpenVZ setup on the same hardware I'm using. This guy uses an own VM for each and every website which is running on his server. I can't think of any advantage why he's using so many VMs.

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >