Search Results

Search found 13909 results on 557 pages for 'old man'.

Page 142/557 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• Trying to retrieve data with a thermaltake blacX enclosure: Windows 7 believes the drive to be "uninitialized"

  - by Peeter Joot

  I have a laptop that won't boot. It appears to be a power problem ... laptop auto-turns-off within about 10 seconds of pressing the power button (with power buttons lighted temporarily and no display with or without external monitor). I've followed the dell troubleshooting guide which suggested reseating the memory modules and the hard drives, but that didn't help. Before trying to have the laptop serviced, I wanted to get some data off off the hard drive. I bought a thermaltake blacX enclosure, intending to use this to both use to retrieve the drive data with, and then later use as external storage. Following the instructions (insert cables, insert drive power on) goes fine, and Windows 7 on another laptop installs the device driver software. However, no drive letter shows up in 'Computer'. Under Computer-manage-storage I see the drive is there, and there's an option to "initialize" the drive. The Windows "initialize" dialog gives me the option to pick between "MBR" and "GPT" partitioning, which sounds like a good way to destroy the data on the drive. I'm thinking that I've purchased the wrong device for the job (or that my old drive is damaged). The old drive to recover info from is a Western Digital 500G/7200rpm SATA drive if that is relavent. Both the original laptop and the one I'm using for recovery are running Windows 7. Does anybody have experience with using a blacX enclosure to recover data off an already formatted drive?

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Z.

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• Linux iptables / conntrack performance issue

  - by tim

  I have a test-setup in the lab with 4 machines: 2 old P4 machines (t1, t2) 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t3) Intel e1000 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t4) Intel e1000 to test linux firewall performance since we got bitten by a number of syn-flood attacks in the last months. All machines run Ubuntu 12.04 64bit. t1, t2, t3 are interconnected through an 1GB/s switch, t4 is connected to t3 via an extra interface. So t3 simulates the firewall, t4 is the target, t1,t2 play the attackers generating a packetstorm thorugh (192.168.4.199 is t4): hping3 -I eth1 --rand-source --syn --flood 192.168.4.199 -p 80 t4 drops all incoming packets to avoid confusion with gateways, performance issues of t4 etc. I watch the packet stats in iptraf. I have configured the firewall (t3) as follows: stock 3.2.0-31-generic #50-Ubuntu SMP kernel rhash_entries=33554432 as kernel parameter sysctl as follows: net.ipv4.ip_forward = 1 net.ipv4.route.gc_elasticity = 2 net.ipv4.route.gc_timeout = 1 net.ipv4.route.gc_interval = 5 net.ipv4.route.gc_min_interval_ms = 500 net.ipv4.route.gc_thresh = 2000000 net.ipv4.route.max_size = 20000000 (I have tweaked a lot to keep t3 running when t1+t2 are sending as many packets as possible). The result of this efforts are somewhat odd: t1+t2 manage to send each about 200k packets/s. t4 in the best case sees aroung 200k in total so half of the packets are lost. t3 is nearly unusable on console though packets are flowing through it (high numbers of soft-irqs) the route cache garbage collector is no way near to being predictable and in the default setting overwhelmed by very few packets/s (<50k packets/s) activating stateful iptables rules makes the packet rate arriving on t4 drop to around 100k packets/s, efectively losing more than 75% of the packets And this - here is my main concern - with two old P4 machines sending as many packets as they can - which means nearly everyone on the net should be capable of this. So here goes my question: Did I overlook some importand point in the config or in my test setup? Are there any alternatives for building firewall system especially on smp systems?

  Read the article

• Only receiving one document at a time from new web server.

  - by Robert Kuykendall

  We're trying to move our internal ticketing system from a Microsoft Small Business Server in the server closet to a Rackspace Cloud Server. The install is Fedora 11 LAMP, and should be default out of the box, except for the vhosts appended to the bottom of the httpd.conf. The new server is suffering from crippling load times, and watching the page load in Firebug it's easy to see the problem occurring, but I can't figure out the cause. Here is the [old server] (http://rkuykendall.com/uploads/old.server.png). I was expecting something like this, but a little slower since it was no longer hosted locally. Instead, the [new server] (http://rkuykendall.com/uploads/new.server.png) appears to only serve one file at a time. Here's another example of this [staircase load time effect] (http://rkuykendall.com/uploads/staircase.png) and another very clear example of the [staircase effect] (http://rkuykendall.com/uploads/staircase2.png). I talked to some guys on Freenode #httpd with no luck. I created a duplicate server to play with, and also created a fresh server with Fedora Core 13 and moved over just the database and web files with no luck. Any suggestions? ( image links disabled due to n00b-spam-restrictions )

  Read the article

• Computer wont start, just blinks on and off

  - by Ryan

  This is really strange. I had a comp that was working fine for over a year, then suddenly it started to shut off, it got so bad that I press the power button and in around 30 secs while booting windows it would shut off, then 20 secs... then 10 secs, then it refused to start all together. So I bought a new PSU (850w Thermaltake, the old one was 550w corsair) thinking that was the problem, I fitted the new PSU now and its the same thing, I press the power button and my fans start for a split second (they have led lights on them, so the lights come on) and then everything goes off again. I thought maybe it was my power button that was loose on my comp, luckily I had another chassis near by so I disconnected the powerSW from the old one and put ran the powerSW from the new chassis, press the power on the new chassis and same thing, it blinks for a split second and off again. Double checked connections from the PSU to the cpu power as well as board mobo power, its tight. It's pretty unlikely both the PSUs have the same exact problem so am lost... Suggestions?

  Read the article

• Exchange Full Access issue

  - by Benjamin Jones

  I was just hired as a System Admin for a small company. They use Exchange 2010 for their Mail Server. I've never had a permission issue like this with Exchange because I worked for a larger firm with less responsibility before. Their old system admin is LONG GONE, so I can't ask him what he did. The issue: Right now ANYONE can gain access to a mailbox and view the mail in the mailbox. This is disabled by default you say and you have to grant them full access ? You are right, but the old System Admin I guess didn't know what he was doing. SO right now user A can open up user B mailbox with out being granted permission. So here is what I found out. Every user in EMC Full Access Permission has Exchange Server group granted. Within the Exchange Server Group, Domain User's is a Member Of. Within Domain User's all user's are listed as Members. So my guess is because of this all users can access ANY mailbox? Well GOOD News. The company is small (35 people) and they are not computer savvy, so hopefully no one has figured out they can open anyone's mailbox.(From what I can tell no). Next thing I did was with my domain user in EMC, delete Exchange Servers Group in FUll Access Permissions and grant access to my user. I made sure that my memeber was apart of the Exchange Server Group. Went to our OWA site and now I don't have permission to my own mailbox. Re did everything to the way it was with my user and now I'm stuck. Any help? I would think granting a single user that is in the Exchange Server group, Full Access to that mailbox would enable them to open that mailbox???? I guess I am wrong.

  Read the article

• OpenVZ container is running but does not show in vzlist nor can I find the private/conf files for the container

  - by Kakeakeai

  I was creating a new OpenVZ container on one of our VPS Nodes while the power went out for that machine. After bringing the machine back online I could no longer access the container CTID=101. I could not destroy it using "vzctl destroy 101", I can not enter or control it, and "vzlist -a" does NOT display any containers at all (this was a fresh node and the first container was being created). I decided to create a new container at this point assuming that the old container just was not saved for some reason. However when I go to add the ip/host to the new container I get a warning that the IP is already in use. After doing a ping to the IP I realized there was a machine on that IP. I SSH into the machine and discover it is the OLD container that some how is orphaned. I can not find it on the filesystem, I can not find it using VZ commands, and It is set to start on Node boot so it is impossible to shutdown (even ssh in and typing the "shutdown now" command just reboots the container not shut it down). Is this a flaw in OpenVZ or am I missing something? I have all the outputs and logs if needed. Thank you all so much in advance.

  Read the article

• If I run two monitors from two different graphic cards, can I still have Twinview?

  - by rumtscho

  I am planning to get a second 2560x1440 monitor for home. The trouble is, I only have 1xDVI, 1xVGA on my graphics card (a 250 GT). I don't want to buy a new graphics card until the prices for the 500 series have stabilized, so probably not before summer (or will it happen earlier? I don't remember how it was for other series, and I couldn't find long-term price history for video cards). The solution I had in mind is to get the 7600 GS from my old PC, which also has 1xDVI, 1xVGA, and run each monitor on a separate card. I have never done that, and I was wondering 1. If I will be able to run the monitors in Twinview then, or will I be stuck with separate X sessions, and 2. Whether there are some other disadvantages as compared to a single-head graphics card. (I am using the proprietary driver because I need compiz). As an aside, how do I find out whether the DVI port on the old graphics card is dual link?

  Read the article

• Getting the EFS Private Key out of system image

  - by thaimin

  I had to recently re-install Windows 7 and I lost my exported private key for EFS. I however have the entirety of my user directory and my figuring that the key must be in there SOMEWHERE. The only question is how to get it out. I did find the PUBLIC keys in AppData\Roaming\Microsoft\SystemCertificates\My\Certificates If I import them using certmg.msc it says I do have the private key in the information, but if I try export them it says I do not have the private key. Also, decryption of files doesn't work. There is also a "keys" folder at AppData\Roaming\Microsoft\SystemCertificates\My\Keys. After importing the certificates I copy those over into my new installation but it has no effect. I am starting to believe they are either in AppData\Roaming\Microsoft\Protect\S-1-5-21-...\ or AppData\Roaming\Microsoft\Crypto\RSA\S-1-5-21-...\ but I am unsure how to use the files in those folders. Also, since my SID has changed, will I be able to use them? The other parts of the account have remained the same (name and password). I also have complete access to the user registry hive and most of the old system files (including the old system registry hives). I do keep seeing references to "Key Recovery Agent" but have not found anything about using, just that it can be used. Thanks!

  Read the article

• Windows 7 automatically logs out when logging in

  - by Luke

  A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

  Read the article

• Configure New Server for .htaccess

  - by Phil T

  I have a new LAMP CENTOS 5 server I am setting up and trying to copy the configuration from another web server I have. I am stuck with what I think is a mod_rewrite problem. If I go to http://old-server.com/any_page_name.php it correctly routes through some handling code in index.php and shows me a graceful "Page Cannot Be Displayed" message. But if I go to http://new-server.com/any_page_name.php I get an ugly Apache 404 Not Found error message. I looked in both httpd.conf files and they both have only one reference to mod_rewrite. LoadModule rewrite_module modules/mod_rewrite.so So it seems like that should be fine. At the bottom of httpd.conf I have the code: <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/html ServerName new-server.com ErrorLog logs/new-server.com-error_log CustomLog logs/new-server.com-access_log common </VirtualHost> Then in the root of /var/www/html I have the exact same .htaccess file that looks like this: RewriteEngine on Options +FollowSymlinks RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] ErrorDocument 404 /page-unavailable/ <files ~ "\.tpl$"> order deny,allow allow from none deny from all </files> So I don't see why the page load at old-server.com works fine while new-server.com doesn't route through index.php like I want it to do. Thanks.

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• mdadm: Replacing array with entirely new drives

  - by hellfur

  I have a server with three 500GB drives, with most of my data in a RAID5 configuration spanning the three of them. I just purchased and installed four 1TB drives, and the intention is to move off of the old drives and onto the new ones. I have enough SATA ports and power connectors to power all seven of my drives at once, so I've kept the old RAID running while I figure out what to do with the new drives. My question is: Should I create a whole new array on the 1TB drives, then move everything over and reconfigure linux to boot from the new md arrays? Or should I just expand the array, swapping out each of the three 500GBs with the 1TB, then adding the final drive? I've read up on the mdadm extending drive setup, and it makes sense, but I imagine I would use one of the drives as a full backup while I move things over, then add that drive back into the array once things are up and running on three of the 1TB drives, so there's some complication in going that route as well... I'm just not sure which is safer/recommended.

  Read the article

• How to change font size on display

  - by Tim

  My laptop is Lenovo T400, whose screen size is 14.1 inches and default resolution is 1440 x 900. My main OS is Ubuntu 10.10. The default font size on the display is somehow small, which might contribute to the fatigue of my eyes. My previous laptop is Acer 5000, whose screen size is 15.4 inches and the default resolution is 1024 x 768. I like reading on my old laptop better than on my new one. Is it possible to change the setting of my new one to look like reading my old one? What are the parameters that control the font size? Are screen size, resolution part of them? In Windows, there are choices for font size, while in Ubuntu I haven't find out where I can change the setting and would like know if someone here knows about it. I also wonder if I can use a separate bigger display (perhaps just like a desktop display) as the display of my laptop, in case I don't want to enlarge font size at the cost of sacrificing the amount of the content to display, and how I shall do it? Thanks and regards!

  Read the article

• Inexpensive (used) hardware for Xen virtualization test?

  - by Jason Antman

  Virtualization is one of the areas where I could really use some experience. I also run quite a few services (web, mail, dns, etc.) out of my home. Since most of my hardware is getting a bit old (I'm running on stuff that was surplused years ago...) I decided that it's about time I start renewing some things, and also play around with virtualization a bit more. My plan is to setup a SAN box (simple iSCSI target, relatively inexpensive gigE switch), get a pair (for starters) of new servers, and start building some new stuff with Xen, specifically planning on playing with live migration and full virtualization. Does anyone have recommendations for used, older "servers" (really anything in a rack-mount form factor, I'm not too worried about things like iLO/iLOM for the test nodes) that support VT-x/AMD-V? I'm biased to HP, but it looks like they didn't make Proliants with VT-x/Vanderpool processors until G6 (for the DL360) or so, which is way out of my price range. I'm looking in the sub-$300 range (or less, if possible), used, probably Ebay. Any recommendations are greatly appreciated. Edit:And, to catch this before the comments start coming - these are personal systems. I have first-generation Proliants still in use (I got them as corporate surplus in 05, they've been running since then, and probably were running since 01 or 02 prior to being sold). I don't need anything shiny and new - I've got a bunch of old boxes, at least one complete replacement for every model in use, and that's fine for me (and easy on the wallet).

  Read the article

• notepad++ select everything between tags

  - by mcflause

  I am doing some langauge translations of an old HTML website so I am just pasting the new translations from a word document into the old files. So I have to select everything between the tags (h2,p,li, etc) and then paste the new text in... from a word file. For selecting everything in between p tags I have to select one side of the inside tag then hold shift then select the next side to highlight everything... my fingers are getting really tired, and I got 40 files (pages) total with 3 languages to do. Is there a shortcut in Notepad++ to select everything between two tags (like when you double click a word it selects the whole word). <p>This is some English that needs to be translated here. I want to just click in this area to select all of this text between these two paragraph tags.</p> <p>This would be another block of translation to do</p> <ul> <li>I want to click here and select everything between the li tags</li> </ul>

  Read the article

• where is my disk space?

  - by user166241

  I recently had a problem with .xsession-errors file - it became very big ( 90GB) and took all disk space: How I can check what takes disk space in /tmp?. I cleaned it with command > .xsession-errors but after an hour it became large again. So I deleted it (rm .xsession-errors) - it helped because it wasn't recreated but again after hour disk space disappeared - now there is no .xsession-errors anymore but I don't know where is the memory: df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 106640456 101223392 4 100% / udev 8166744 8 8166736 1% /dev tmpfs 3270224 972 3269252 1% /run none 5120 0 5120 0% /run/lock none 8175552 152 8175400 1% /run/shm du -sc * .[^.]* | sort -n 0 initrd.img 0 initrd.img.old 0 proc 0 sys 0 vmlinuz 0 vmlinuz.old 4 cdrom 4 lib64 4 media 4 mnt 4 selinux 8 dev 12 srv 16 lost+found 68 tmp 1124 run 3396 lib32 5164 .rpmdb 5540 root 8888 sbin 9120 bin 17132 etc 106080 opt 116956 boot 861908 lib 3530584 usr 3821836 var 13371260 home 21859112 total So there is around 100GB used but executing du -sc * .[^.]* | sort -n in root directory finds only ~21 GB - so what takes 80GB?? How to check it? I suspect that when I deleted the `.xsession-errors' file the errors were redirected somwhere else - but where?

  Read the article

• Information on the BMPP File Extension/Format

  - by Angel Brighteyes

  I am looking for information on the file type BMPp. Namely I need an application that can create this file type, preferably open source or free. Wikipedia says for BMP File Format that 'BMPp' is a "type code", which is the "mechanism used by pre-OSX Macs ... to denote a files format..." (Look in the little info-box of general information under "Type code"). Continuing my research, I found an old 2009 archived mailing list "Re: Incorrect png file type 'PNG' that talks about something related to another problem a developer is having. In the response he talks about there being variant file types, and lists BMPp as being linked to an old version of Graphics Converter. The company Lemkesoft sells Graphics Converter, which I am not willing to purchase. I can't imagine that the only program in existence to make a BMPp file is that program. There has got to be another way to make that file type, other than creating a BMP file and just renaming it to BMPp (unless of course it is really that easy)? This is the first time I've run into this file format, and it took a bit on Google, Bing, and Wikipedia to find the information that I've posted here. Any further help would be appreciated.

  Read the article

• What happened to 'Copy Public Gallery Link' for folders in Photos in Dropbox?

  - by Transgenic

  I've been trying to figure out how to use the 'Photos' folder properly, but it does not seem to contain the functionality that is mentioned on various websites. From what I've read, you are supposed to create a folder within the 'Photos' folder. At that point, it becomes a public gallery for which you can access the context menu item Copy Public Gallery Link. However, I do not have this context menu item. I found a topic on the DropBox forum, but it is 2 years old. Even the various website information mentioned is over a year old. I found a topic from this year on SuperUser that mentions about the Share link menu item. I understand that this functionality is basically the same as Copy Public Gallery Link, however, the key difference is that it opens the website for which I need to click 'Copy link to this page' link, which then adds it to the clipboard. My primary questions are: Did they phase out the Copy Public Gallery Link from the context menu entirely? If not, is there a way to re-enable this menu item? If not, am I using the Photos folder properly? Lastly, if there is no way to get this menu item, is there some kind of script or hack-around that will let me simplify the Shark link + Copy link to this page functionality without requiring it to open my web browser? Note: I had to edit my post to remove other website links that I mention since I'm considered a 'New User' here and am only able to post 2 hyperlinks. Sorry.

  Read the article

• Folder Sharing NTFS permissions with Share Permission

  - by Muhammad Adly

  i have a problem on my domain, the history starting from when i had a server with WIN 2008 r2 installed with the following roles installed on it (AD, DNS, DHCP, File). From 1 month i decided to install a new server 2008 r2 server to get (AD, DNS, DHCP) and leave the file server on the old one. i did the following exactly: 1) robocopy all my data on external HDD 2) Install a new server with 2008 r2 3) transfer all 5 roles to transfer the domain to the new server (MainDC) 4) issue (NETLOGON, SYSVOL) not transferred but i decided to reinitialize them again an now they are operating (MainDC) 5) re-create and re-configure a new GPOs and link it to my OUs 6) reinstall Old server operating system with a fresh installation of WIN 2008 R2 (FileServer) 7) join my domain with my domain credentials. the issue when i tried to share folder on \fileserver the permissions that i had set in sharing permissions are applied on the main shared folder and subfolders. the security settings are not applied. i.e. Say i'm sharing \fileserver\MainFolder with sharing permission for Authenticated Users that can read, so every one can read this main shared folder, if i set security permission for \fileserver\MainFolder\User1 that User1 can Read\Write\Modify. User1 can not perform this processes when accessing it from Network Share, i tried alot of steps from topics online get ownership for folder, remove inheritance from parent folder, applying changes for child objects, i tried also to construct a new folder structure but also the same issue, i tried another host PC, also i get the same issue.

  Read the article

• How to block access to addresses outside network (internet)

  - by devnull

  I have a homeserver, that is now connected to the internet with an own network device (ath0 - 192.168.1.x). It also has one more network interface (eth0 - 192.168.0.x). Soon I will get a second internet line that will be connected the second network. The server then has both networks with different internet lines available, but i only want it to connect to the internet on the old ath0 interface - not the new eth0 (192.168.0.x). Background of that constellation is that the new line has a volume-limit in traffic - the old hasn't and i need the new line for all mobile devices and laptops. The devices should be able to use the new network to connect to the internet and the server. The homeserver is a debian 6 with iptables and some already written rules for it. I need now a rule to block all outgoing internet access on the eth0 interface - i guess it could be something with --target != 192.168.0.0 but i did not succeed in finding the proper solution. Edit: found the solution: iptables -A OUTPUT -o eth0 -d 192.168.0.0/24 -m state --state NEW,ESTABLISHED -j ACCEPT With that setting, all traffic that uses the eth0 interface is only allowed if the destination is inside the network 192.168.0.x - all other traffic is denied .

  Read the article

• Virtual machine shows no network adapter

  - by Logman

  I had a an old Lotus/Domino server (R5), I just virtualized. It ran Windows 2000 server. I had to use Vmware Converter v3.x to create the vm because it was the only one I could find that could actually do a Win2k machine that had no service packs. It was just put out to pasture a couple months ago, so it isn't being used except to store the old email for archiving. It took a bit of work to get it onto the Win2008R2 servers hyper-v but I got it there. Problem now, is that the network adapter didn't show up. I could not install the guest additions because it needed sp4 + on win2k... so I installed sp4 onto the vm guest. Everything seems fine except the network adapter still isn;t showing up in device manager. NOthing. Now this server had an external ip, and I did not want it to be put onto the internal virtual network. I am going to use a dedicated adapter on the host (hyper-v server) if that matters... but this shouldn't matter if the the guests network adapter doesn't show at all. Thoughts?

  Read the article

• How two completely unrelated software can affect each other in a very strange manner?

  - by user40602

  I installed an old game on my old PC and it doesn't work; its process/exe file was listed in task manager but nothing appeared on the screen. then some time later i discovered that when some specific program was running an my pc, that game could be executed without that problem! although i am myself a power user and also a programmer, i couldn't find the reason, and don't have any good guesses about it. i just know that when i want to run that game i should have another specific and unrelated program running. i ask if anyone has any idea/guess about the possible reasons for this rare phenomenon! oh and if u ask about the details/names of those programs, i am afraid of telling that, because others may think i am kidding, but i am not (please believe me!), that game is NFS2 and the other program is mysqld.exe (i said before that i am a programmer!). I don't know how mysqld.exe (yes it is the windows version of the famous MySQL DBMS server) can affect NFS2 in such an strange manner, and my curiosity and profession don't let me to forget seeking for the answer, so i decided to take the help of others to see if someone has had a similar experience or a reasonable idea about it.

  Read the article

• Two video card on one Mobo

  - by InfinityKing

  I recently purchased a new HP Pavilion p6-2265eo. It was then that I realised that it has only one DVI and one HDMI output.. I will connect my TV with the HDMI. so I am letft with only one DVI output. I need to have two monitors. Please help. Should I purchase a new video card and install it? My knowledge is limited. The specifications of my comp says that there is 1 x PCI-E x16, 3 x PCI-E x1. 1) I suppose that the video card already present in my purchase is connected on the PCI-E x16. Am I right? I dont want to open my desktop right now and check it for myself as it can void the warrenty. so I need an experienced person to tell me that. 2) I have an old nvidia geforce 7200 gt. Is it possible for me to connect it to my left over PCI-E x1? I searched for PCI-E x1 on the net and as far as I can understand the slot is too small for my old nvidia geforce 7200 gt graphic card. 3) what are the options? Please help this dummo :) Thankign you in advance,

  Read the article

• Diagnosing PC crashes (most often while using shared folders or torrents)

  - by Dyppl

  For the last few weeks my PC (pretty old P4 with WinXP SP3) has been crashing randomly. It just suddenly reboots instanteneously. It feels hardware-related but I wasn't able to determine wether it's software or hardware that causes it. I did notice a pattern though: it's more likely to crash when I copy a lot of files over network or have uTorrent running, but sometimes it crashes when I am not doing anything with it. Copying files from it over network causes it to crash in 1 to 10 minutes almost every time. Using torrents causes it to crash every 1-3 hours. With neither or that on it crashes every 24 hours or so. I ruled out the following probable causes: PSU (I bought a new one and turned off most of the drives so the power is sufficient 100%) Bad HDD or interface cable on my SATA disk from which I was originally copying the data over network (bought new SATA cable and later yanked out the HDD completely, PC still crashes without it) Video adapter (AGP slot is now empty, using the onboard VGA at the moment) Network adapter (removed it from PCI, using onboard LAN) CPU (I think: I changed the termopaste and it's temperature is below 50C) RAM (I think: I ran Memtest86 and it didn't show any errors) At the moment I only have only one system HDD and DVD drives, a mouse and a keyboard plugged in. The fact that it crashes most often when I use network extensively makes me think that maybe it's software related (I removed the network adapter from PCI and now am using an onboard one, so network hardware is unlikely to cause problems). I am now pondering system reinstall but it's not a pleasant solution so I decided to ask wether there are better ideas first. If someone can share a good diagnostic tool it would be great because I didn't find anything good. Thanks in advance, I hope that "help to diagnose" questions aren't entirely banned here. EDIT: Motherboard is actually ~4 years old as I replaced it back in 2007

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >