Search Results

Search found 4953 results on 199 pages for 'special treatment'.

Page 142/199 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• SMTP Unreachable from Specific Networks

  - by Jason George

  I host my business site through a VPS account. The instance runs Ubuntu and I'm using POSTFIX+Dovecot as my mail server. For the most part, the mail server works fine. I have noticed, however, that I can not send mail from specific local networks. I noticed this at a client's office serval months ago. I can receive email, but any time I tried to send mail when connected to their network the connection would time out. Since I could send my mail after leaving, I chalked it up to improper network configuration and didn't worry about it. Unfortunately I've recently moved, switched service providers, and am forced to use the service providers router due to the special set-up they put in place to give me DSL in the sticks--well beyond the typical range for a DSL run. Now I'm unable to send email from home, which is a problem. I have tried sending email through my phone (using cellular service rather than my DSL) just to confirm the server is currently working. I'm not even sure where start debugging. Any ideas on how I might track down the issue would be greatly appreciated.

  Read the article

• Unable to authenticate to Windows Server 2003 for file browsing as non-administrator user.

  - by Fopedush

  I've got a windows server 2003 box containing a raid 5 array I use for mass storage. I want to set up a special non-administrator account that can be used to browse files over the network, with only read access. Ideally I'll map my network drive as this user to avoid accidentally hosing my data, and mount as an administrator user on occasions where I actually need write access. I've created a non-administrator user on the Windows Server box (called "ReadOnly)", and granted the user read permissions on the folders I need. However, when I try to browse to the files, and authenticate as this user, I'm told "Permission denied". If I throw the readOnly user into the administrators group, however, I can authenticate and browse just fine. I am, of course, only attempting to browse to folder for which I have given this user read permissions. Obviously my ReadOnly user is missing some privilege here, but I can't figure out what it is. I've been digging around in group policy editor all day to no avail. What am I missing? Fake Edit: I'm doing my browsing from a Windows 7 box, but I don't think that is relevant.

  Read the article

• ProCurve network expansion

  - by Blue Warrior NFB

  I've hit a bit of a wall with our network scale-out. As it stands right now: We have five ProCurve 2910al switches connected as above, but with 10GbE connections (two CX4, two fiber). This fully populates the central switch above, there will be no more 10GbE Ethernet connections from that device. This group of switches is not stacked (no stack directive). Sometime in the next two or three months I'll need to add a sixth, and I'm not sure how deep of a hole I'm in. Ideally I'd replace the core switch with something more capable and has more 10GbE ports. However, that's a major outage and that requires special scheduling. The two edge switches connected via fiber have dual-port 10GbE cards in them, so I could physically put another switch on the far end of one of those. I don't know how much of a good or bad idea that would be though. Is that too many segments between end-points? Some config-excerpts: Running configuration: ; J9147A Configuration Editor; Created on release #W.14.49 hostname "REDACTED-SW01" time timezone 120 module 1 type J9147A module 2 type J9008A module 3 type J9149A no stack trunk B1 Trk3 Trunk trunk B2 Trk4 Trunk trunk A1 Trk11 Trunk trunk A2 Trk12 Trunk vlan 15 name "VM-MGMT" untagged Trk2,Trk5,Trk7 ip helper-address 10.1.10.4 ip address 10.1.11.1 255.255.255.0 tagged 37-40,Trk3-Trk4,Trk11-Trk12 jumbo ip proxy-arp exit

  Read the article

• How to compare old CPU to new CPU?

  - by Lasse V. Karlsen

  I hope this question doesn't get closed at once :) I have an old laptop, a Compaq NC4200, which is going its final laps around the track these days. Battery is dead, and everything kinda runs slow. It also has only 1GB of memory, and even though I don't know if it can take more, I probably wouldn't be able to get hold of any that matches without having to special order it. The size, however, has been ideal for my usage pattern, so I'm looking to replace it with a similarly sized laptop, at least in the same size category. However, it's been a while since I tried keeping track of CPUs, so I have a question. The old laptop has a Intel Pentium M 760 1.86GHz processor. One laptop I found online has a Intel Pentium SU4100 1.3GHz dual-core. This type of processor seems to be quite common in the price and size-range I've been looking. What kind of relative performance boost could I expect from the old one to the new one? I am not expecting a "about 7.45x speed", but some indication would be nice. For instance, dual-core tells me it might be akin to 2.6GHz, but I assume I can't simply compare 1.86GHz to 2.6GHz and expect the new one to run about 1.4x as fast, I expect more these days. Or is that unrealistic for this kind of processor? Do I need to up my price range and go for a 2+ GHz processor?

  Read the article

• GRE Tunnel over IPsec with Loopback

  - by Alek

  I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• Windows Vista Nested Desktop Folders Problem

  - by Samuel Walker

  I have no idea how, nor when this happened, and it's started to really quite annoy me. When navigating through Explorer, by clicking on Icons I have C:\Users\Samuel\Desktop (Icon is the blue special Desktop icon), which contains the items I see on my Desktop. I then have the following folder: C:\Users\Samuel\Desktop (Icon is the standard yellow folder icon), which contains many program shortcuts, and is completely seperate from the other C:\Users\Samuel\Desktop Then in the Yellow Icon Desktop I have the sub-folder Desktop with the blue icon that is a direct mirror of the blue C:\Users\Samuel\Desktop folder (as in a new folder / file shows up in both). In explorer when I directly type C:\Users\Samuel\Desktop I am taken to the Yellow folder version. If I go to C:\Users\Samuel\Desktop\Desktop I am taken to the Blue folder version. Finally, from cmd cd'ing to C:\Users\Samuel\Desktop takes me to the Yellow folder version whilst C:\Users\Samuel\Desktop\Desktop takes me to the blue folder version. How on earth can I get rid of the yellow folder version leaving the blue C:\Users\Samuel\Desktop. I can't delete either as it says they're in use. UPDATE: Ok, so it looks like doing a dir from cmd lists only one Desktop folder - the Yellow one. In addition, it looks like I can't delete either of them (given that they both contain my 'Desktop'

  Read the article

• New keyboard for linux: Adesso Tru-Form or MS Natural Keyboard 4000?

  - by Andrea

  Hi folks! I'm going to buy a new ergonomic keyboard for my laptop. In the following, keep in mind I live in Italy. I considered the following models: Adesso PCK-308UB - Adesso Tru-Form™ Pro - Contoured Ergonomic Keyboard with TouchPad-PS2 Pro: has a built-in touchpad in the same position of my laptop somewhat cheaper than the alternative below Cons: the surface doesn't seem to be bowl-shaped. keys seem to lay on a straight slightly-inclined surface. It seems an idea used extensively in other ergonomic keyboards according to a few comments on the net, new Adesso keyboards seem to lack robustness, they're likely to loose small parts after a few weeks or months. Other users, instead, seem to never had any problem in years and swear by their quality and comfortability. Those who had problems, however, lamented a lack of responsiveness from the manufacturer. I'm not sure whether the keyboard, at least the standard keys, and the touchpad will both be recognized correctly under linux distros (I mostly use FC btw) last time I checked, Adesso didn't have local resellers in my country Microsoft Natural Ergonomic Keyboard Pro: recognized as one of the most comfortable keyboards reliable customer service operating in my country AFAIK there are several documented ways to get extra buttons work with linux Cons: it doesn't have a builtin touchpad and has a numeric keypad wasting space to reach mouse But there could be other keyboards I haven't considered yet, so here follows my ideal keyboard wishlist, ordered by priority linux compatible basic ergonomic design, which entails split tilted keyboard and pads advanced ergonomic design, like true-ergonomic's or kinesis , where special keys (like enter, caps-lock...) are placed symmetrically in the middle to be used by thumbs a builtin touchpad/trackball placed under the keyboard. I just love this on my notebook. I think it's pretty effective, since it allows my hand to rest naturally everytime I use it. Any opinion on this? high-quality switches, like cherry's (unsure about this one) additional programmable keys placed near usual ones, to simplify typing shortcuts TIA Andrea

  Read the article

• Keyboard's media keys are blocked by a program

  - by Mike Hanson

  I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

  Read the article

• Change the number of consecutive frequent ssh login before temporary blocking the user login

  - by Kenneth

  my server currently would temporarily refuse a user to login for certain amount of time (maybe ~20min) if the user consecutively frequent ssh login for 3 times. Can I change this behaviour (say relaxed the definition of frequent maybe from 'within 5 sec' to 'within 10 sec'; or increase the # of consecutive login from 3 to 5)? Thanks. Added: Ah.. now I think the problem was not with the ssh. I just tried on another newly installed server. consecutive successful login won't block the user. I have no sudo permission on the server I mentioned above. Now I suspect this behaviour may cause by the firewall in the system. Thanks everyone's comments. ADDED 2: Ah... after some searches. I think the server is using /sbin/iptables to do it as I can see the iptables program is there even though I don't have permission to list the rules. Thanks everyone, special thank to jaume and Mark!

  Read the article

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• Using AddEncoding x-gzip .gz without actual files

  - by STATUS_ACCESS_DENIED

  With Apache (2.2 and later) how can I achieve the following. I want to transparently compress using GZip encoding (not plain Deflate) the output when a certain file is queried with its name plus the extension .gz, where the .gz version doesn't physically exist on disk. So let's say I have a file named /path/foo.bar and no file foo.bar.gz in the folder to which the URI /path maps, how can I get Apache to serve the contents of /path/foo.bar but with AddEncoding x-gzip ... applied to the (non-existing) file? The rewrite part appears to be easy, but the problem is how to apply the encoding to a non-existent item. The other way around also seems to be simple as long as the client supports the encoding. Is the only solution really a script that does this on the fly? I'm aware of mod_deflate and mod_gzip and it is not what I'm looking for - at least not alone. In particular I need an actual GZIP file and not just a deflated stream. Now I was thinking of using mod_ext_filter, but couldn't bridge the gap between rewriting the name of the (non-existent) file.gz to file on one side and the LocationMatch on the other. Here's what I have. RewriteRule ^(.*?\.ext)\.gz$ $1 [L] ExtFilterDefine gzip mode=output cmd="/bin/gzip" <LocationMatch "/my-files/special-path/.*?\.ext\.gz"> AddType application/octet-stream .ext.gz SetOutputFilter gzip Header set Content-Encoding gzip </LocationMatch> Note that the header for Content-Encoding isn't really needed by the clients in this case. They expect to see actual GZIP files, but I want to do this on-the-fly without caching (this is a test scenario).

  Read the article

• Dell XPS m1530 system cannot boot need 130w or greater

  - by KPS

  I have a Dell XPS M1530 and I lost my old AC adapter but ordered a new one. For the longest time it always had a battery charge so I was able to boot into the OS but now it is completely dead. I have a generic charger that slowly charged the laptop when it was in the OS but does not when the computer is off. When I boot up I get the following error: The AC power adapter type cannot be determined. The system can only boot with a 130 W power adapter or greater. Strike F1 key to shutdown. I cannot even enter the BIOs setup screen or boot menu, is there a way around this? I heard from the local tech that Dell has a special feature to boot from thumb drive before getting past the initial logo. I am doing my best to avoid purchasing a new charger since it worked just fine when the OS was running, I am hoping to get this thing going. Is there a way to charge the battery externally? Thanks in advance for any help!

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

  - by Horst Walter

  On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

  Read the article

• How To Map Fn+Key (Multiple Keys) To Other Key in Windows?

  - by Mohamed Meligy

  I've got a ThinkPad W530 laptop, which replaces the Application Key (also known as Menu Key or Mouse Right Click key, usually between Right Alt and Right Ctrl) with the Print Screen key. So, I need to replace Prt/Scr with Application key. That's easy, all key mapping software like SharpKeys or whatever can do that. There are even a few threads in SuperUser about dozen of those. But then, the different part to this question from the others (which is why it's not a duplicate, I think) is that I also don't want to completely lose the Prt/Scr key. I'm thinking about replacing it with either: Fn + Prt/Scr Fn + F2 These seemed to have no special meaning, so, I'm not overriding anything, just adding functionality to either of them (one of them, not both), to be the new Prt/Scr key. I couldn't find any key mapping software that can detect or let me select more than one key to map, even when the other key is something like Fn key (although they all can map Fn key itself, without combination). I know it may make sense why this restriction exists, but it'll be really useful if I can override it though. Do you know any program that can do that? Thanks a lot.

  Read the article

• Chipset fan on the frtiz - compressed air hasn't fixed anything - is there anything I can do?

  - by Anthony

  Yesterday, my computer started to make an annoying whining noise. Knowing that this is likely a fan issue, I opened the case and proceeded to determine which fan was causing the issue. I got some compressed air and tried cleaning out the dust around it (and the rest of the computer while I was at it). This hasn't seemed to fix the issue. Now, if it were just any fan, I would probably just replace the fan - they're relatively cheap after all. However, this is a special fan. Aside: For what its worth, I feel bad that the graphics card blocks part of the fan, but it is the only slot the graphics card fits, so I had no choice. After pulling out my motherboard user guide, it looks like this is a fan placed directly on top of the chipset. To be perfectly honest, I have no clue what the purpose of the chipset is - but it sounds important. After some quick research, I see that it is responsible for providing the bridge between my CPU, RAM and graphics, among other things. Just a quick search at Newegg tells me that chipset fans can be purchased at pretty reasonable prices (< 20 dollars). Is it practical to replace this fan? It is an old computer as computers go and I wouldn't be terribly upset to upgrade the motherboard and processor, so perhaps this is a sign. Hardware Specs: Motherboard: Asus A8N-E Chipset: NVIDIA nForce4 Ultra

  Read the article

• How to transfer Windows Vista disk image to new machine

  - by Mike Hobbs

  I'm trying to upgrade a user's machine to some better hardware. I know of Easy Transfer, but I'd rather not have to reinstall all the programs that are already present. (Some of which are no longer available, anyway). Instead, I'm trying to transfer the entire disk image from one machine to the other, but I ran into issues. If I copy the partition image over to the new machine using Clonezilla, I get errors on boot saying that I need to insert the Vista install disk and run repair. I do that, but it then says that it is unable to repair whatever it is that's broken. Next, I tried to sysprep the old machine before creating the image, but sysprep fails saying that it encountered some sort of system error. Should it be possible to sysprep any arbitrary machine, or does it only work on a relatively clean install? Could it be a missing driver that is tripping me up? The new machine is a fairly stock desktop that shouldn't need any special drivers beyond what's already present in standard Vista. Are there any foolproof methods for doing this sort of thing?

  Read the article

• Block protect (Keep last line of paragraph with next paragraph)

  - by Ed Cottrell

  Is there a way to force Microsoft Word 2010 to keep the last line of a paragraph with the next paragraph? An example of when this is relevant is when starting a block quote; it doesn't look good to have the block quote start at the top of a new page, particularly when it's introduced by a partial sentence, like this: "Lorem ipsum" is sample text widely used in the publishing industry, as the text has spacing roughly similar to that of English and therefore looks "normal" but unintelligible to an English reader's eye, allowing the reader to focus on design elements. It begins, Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam rhoncus laoreet risus, quis congue leo viverra congue. Suspendisse magna massa, viverra imperdiet est eu, ultrices volutpat lectus. Sed pulvinar est id risus lobortis venenatis. There shouldn't be a page break after "begins," because it looks like the sentence ends abruptly. "Keep lines together" won't work, because by definition we're talking about two paragraphs. "Keep with next" won't work if the first paragraph is larger than a couple of lines, because then you get an awkwardly large space at the bottom of a page. Manual line breaks obviously work, but only when the document is final, which is often less certain than it seems. I know WordPerfect has a feature called "block protect" that does this, but I have not found even an acceptable substitute in Word. I have played with style separators and hidden paragraph breaks, but to no avail. I would love a special character, kind of like the nonbreaking space or zero width optional space, that tells Word to move to the next page if the next paragraph would otherwise start the page. A macro would also be great, but I haven't been able to find a starting point (like how to detect where non-manual page breaks fall). Edit: It looks like "Keep with next" works this way in Word 2013, but I specifically need a fix that works in Word 2010.

  Read the article

• SSH client and Command Prompt replacements Windows look-and-feel

  - by Oddthinking

  The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

  Read the article

• VoIP setup for one external PSTN line

  - by Jcl

  I'm completely new to VoIP and the likes, and I'm trying to find information about what could be the best setup for this. I need 4 (maybe more in the future, but maximum 5 or 6) wireless extensions, connected to 1 PSTN line, and maybe 2 in the future. I've been trying to gather information about the gear needed but everything I find seems too much over-the-top (and extremely expensive). The main problem is that the physical place we are on doesn't have possibilities of having a decent internet connection, so using a external VoIP "virtual PBX" is not an option. Thing is, even if small, phone is critical to this organization. I currently have an analog DECT/GAP PBX which does what I need, however the PBX is very bad and the call quality is horrible, and that's why I want to change it. The requirements would be: 4 wireless terminals (routing cable is not an option), all of them ringing on incoming PSTN calls. Ability to do internal calls (4 separate offices) and ability to pass calls between terminals. The 4 terminals should be able to access the external PSTN line without dialing any special codes. Very important: terminals should be able to issue commands on the PSTN line to the external operator in the form *nn*nnnnnnnn# . Don't know wether this could face to be a problem, but I've had problems with analog PBX which would take any * as a PBX command and wouldn't allow terminals to send it to the external lines. Not so important, but would be nice to have: call waiting music Could anyone recommend such a setup? I need to be able to do this on a EXTREMELY LIMITED budget (that is: I don't have a limit, but all should get as much to zero as possible). I have enough spare powerful computers and a 300mbps wireless network which works just fine, so that's not to include in the budget. Don't really know if this is the best place to ask, but it's the most StackExchange-related site I've found to this subject.

  Read the article

• Unable to connect to CopSSH when running Windows service, works when running sshd directly

  - by Joe Enos

  I've been using CopSSH (that uses OpenSSH and Cygwin, so I don't know which of the three is the problem) as my SSH server application at home on Windows 7 Ultimate 32 bit. I have used it for about a year with no real problems, other than it sometimes takes 2 or 3 connection attempts to get through, but it's always worked within a few attempts. A few days ago, it just stopped working. The Windows service is still running, and I've rebooted, restarted the service, etc. with no change. On the client (using Putty on Windows), I get the message "Software caused connection abort". On the server, my event viewer registers the following: fatal: Write failed: Socket operation on non-socket I finally got it working, but only by executing sshd.exe directly from the command line on the server. No special flags or options, just straight execution, and then when I connect remotely, it goes through. I do have firewall and anti-virus software which appears to be configured properly, but the fact that things work when running sshd.exe also indicates that the firewall is fine. I thought the service and executable did exactly the same thing, but apparently there's some difference. Does anyone have any ideas on where I should look for the problem? If I can't find something, I suppose I can write a Windows service or scheduled task that fires off sshd.exe directly and ensures that it stays running, but that's kind of a last resort, since it's just wrapping around something that should already work. I appreciate your help.

  Read the article

• What's up with stat on Macos/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Macos 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputing the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• What's up with stat on Mac OS X/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Mac OS X 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev <volfs> 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) <volfs> on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputting the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >