Search Results

Search found 21317 results on 853 pages for 'address bar'.

Page 144/853 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

  • Lynksys WRT120N wireless router not connecting to ADSL

    - by pradeetp
    I have a lynksys WRT120N wireless router that was connected to Sterlite ADSL modem. The internet connection was working fine through wireless access. I changed the ADSL router because it developed some power issues and got it replaced with the same model/brand from the service provider. However I am not able to access internet now. Here is the current setting Sterlite SAM300 XA IP Address: 192.168.2.1 (I changed it to this IP because the IP address of my ADSL router was same) Lynksys WRT120N wireless router IP Address: 192.168.1.1 If I connect my laptop to ADSL router directly, the internet works fine. It is only that that if I access it wirelessley through wireless router that I am not able to connect to internet. The IP address setting has been configured to obtain IP address automatically. I have windows 7 OS home edition. Could someone please help me to fix this issue.

    Read the article

  • Best Way to Handle Meta Information in a SQL Database

    - by danielhanly.com
    I've got a database where I want to store user information and user_meta information. The reason behind setting it up in this way was because the user_meta side may change over time and I would like to do this without disrupting the master user table. If possible, I would like some advice on how to best set up this meta data table. I can either set it as below: +----+---------+----------+--------------------+ | id | user_id | key | value | +----+---------+----------+--------------------+ | 1 | 1 | email | [email protected] | | 2 | 1 | name | user name | | 3 | 1 | address | test address | ... Or, I can set it as below: +----+---------+--------------------+--------------------+--------------+ | id | user_id | email | name | address | +----+---------+--------------------+--------------------+--------------+ | 1 | 1 | [email protected] | user name | test address | Obviously, the top verison is more flexible, but the bottom version is space saving and perhaps more efficient, returning all the data as a single record. Which is the best way to go about this? Or, am I going about this completely wrong and there's another way I've not thought of?

    Read the article

  • location getting some times and sometimes not

    - by Chaitanya Sai
    // in this i'm getting location sometimes and sometimes location is not retrieving i had turned gps and gprs on and added permissions required . i'm bot getting what actually the problem is package com.example.addr; import java.util.List; import java.util.Locale; import android.location.Address; import android.location.Criteria; import android.location.Geocoder; import android.location.Location; import android.location.LocationListener; import android.location.LocationManager; import android.os.Bundle; import android.app.Activity; import android.content.Context; import android.view.Menu; import android.widget.TextView; public class MainActivity extends Activity { @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); LocationManager locationManager; String context = Context.LOCATION_SERVICE; locationManager = (LocationManager)getSystemService(context); Criteria crta = new Criteria(); crta.setAccuracy(Criteria.ACCURACY_FINE); crta.setAltitudeRequired(false); crta.setBearingRequired(false); crta.setCostAllowed(true); crta.setPowerRequirement(Criteria.POWER_LOW); String provider = locationManager.getBestProvider(crta, true); // String provider = LocationManager.GPS_PROVIDER; Location location = locationManager.getLastKnownLocation(provider); updateWithNewLocation(location); locationManager.requestLocationUpdates(provider, 2000, 10, locationListener); } private final LocationListener locationListener = new LocationListener() { @Override public void onLocationChanged(Location location) { updateWithNewLocation(location); } @Override public void onProviderDisabled(String provider) { updateWithNewLocation(null); } @Override public void onProviderEnabled(String provider) { } @Override public void onStatusChanged(String provider, int status, Bundle extras) { } }; private void updateWithNewLocation(Location location) { String latLong; TextView myLocation; myLocation = (TextView) findViewById(R.id.myLocation); String addressString = "Sorry No Address Found"; if(location!=null) { double lat = location.getLatitude(); double lon = location.getLongitude(); latLong = "Lat:" + lat + "\nLong:" + lon; double lattitude = location.getLatitude(); double longitude = location.getLongitude(); Geocoder gc = new Geocoder(this,Locale.getDefault()); try { List<Address> addresses= gc.getFromLocation(lattitude, longitude, 1); StringBuilder sb = new StringBuilder(); if(addresses.size()>0) { Address address=addresses.get(0); for(int i=0;i<address.getMaxAddressLineIndex();i++) sb.append(address.getAddressLine(i)).append("\n"); sb.append(address.getLocality()).append("\n"); sb.append(address.getPostalCode()).append("\n"); sb.append(address.getCountryName()); } addressString = sb.toString(); } catch (Exception e) { } } else { latLong = " NO Location Found "; } myLocation.setText("Current Position is :\n"+ latLong + "\n"+ addressString ); } @Override public boolean onCreateOptionsMenu(Menu menu) { getMenuInflater().inflate(R.menu.activity_main, menu); return true; } }

    Read the article

  • JOGL Double Buffering

    - by Bar
    What is eligible way to implement double buffering in JOGL (Java OpenGL)? I am trying to do that by the following code: ... /** Creating canvas. */ GLCapabilities capabilities = new GLCapabilities(); capabilities.setDoubleBuffered(true); GLCanvas canvas = new GLCanvas(capabilities); ... /** Function display(…), which draws a white Rectangle on a black background. */ public void display(GLAutoDrawable drawable) { drawable.swapBuffers(); gl = drawable.getGL(); gl.glClear(GL.GL_COLOR_BUFFER_BIT | GL.GL_DEPTH_BUFFER_BIT); gl.glClearColor(0.0f, 0.0f, 0.0f, 0.0f); gl.glColor3f(1.0f, 1.0f, 1.0f); gl.glBegin(GL.GL_POLYGON); gl.glVertex2f(-0.5f, -0.5f); gl.glVertex2f(-0.5f, 0.5f); gl.glVertex2f(0.5f, 0.5f); gl.glVertex2f(0.5f, -0.5f); gl.glEnd(); } ... /** Other functions are empty. */ Questions: — When I'm resizing the window, I usually get flickering. As I see it, I have a mistake in my double buffering implementation. — I have doubt, where I must place function swapBuffers — before or after (as many sources says) the drawing? As you noticed, I use function swapBuffers (drawable.swapBuffers()) before drawing a rectangle. Otherwise, I'm getting a noise after resize. So what is an appropriate way to do that? Including or omitting the line capabilities.setDoubleBuffered(true) does not make any effect.

    Read the article

  • Toolbar items in sub-nib

    - by roe
    This question has probably been asked before, but my google-fu must be inferior to everybody else's, cause I can't figure this out. I'm playing around with the iPhone SDK, and I'm building a concept app I've been thinking about. If we have a look at the skeleton generated with a navigation based app, the MainWindow.xib contains a navigation controller, and within that a root-view controller (and a navigation bar and toolbar if you play around with it a little). The root-view controller has the RootViewController-nib associated with it, which loads the table-view. So far so good. To add content to the tool bar and to the navigation bar, I'm supposed to add those to in the hierarchy below the Root View Controller (which works, no problem). However, what I can't figure out is, this is all still within the MainWindow.xib (or, at runtime, nib). How would I define a xib in order for it to pick up tool bar items from that? I want to do (the equivalent of, just reusing the name here) RootViewController *controller = [[RootViewController alloc] initWithNibName:nil bundle:nil]; [self.navigationController pushViewController:controller animated:YES]; [controller release]; and have the navigation controller pick-up on the tool bar items defined in that nib. The logical place to put it would be in the hierarchy under File's Owner (which is of type RootViewController), but it doesn't appear to be possible. Currently, I'm assigning these (navigationItem and toolbarItems) manually in the viewDidLoad method, or define them in the MainWindow.xib directly to be loaded when the app initializes. Any ideas? Edit I guess I'll try to explain with a picture. This is the Interface Builder of the main window, pretty much as it comes out of the wizard to create a navigation based project. I've added a toolbar item for clarity though. You can see the navigation controller, with a toolbar and a navigation bar, and the root view controller. Basically, the Root View Controller has a bar button item and a navigation item as you can see. The thing is, it's also got a nib associated with it, which, when loaded will instantiate a view, and assign it to the view outlet of the controller (which in that nib is File's Owner, of type RootViewController, as should be). How can I get the toolbar item, and the navigation item, into the other nib, the RootViewController.nib so I can remove them here. The RootViewController.nib adds everything else to the Root View Controller, why not these items? The background for this is that I want to simply instantiate RootViewController, initialize it with its own nib (i.e. initWithNibName:nil shown above), and push it onto the navigation controller, without having to add the navigation/toolbar items in coding (as I do it now).

    Read the article

  • How to honor/inherit user's language settings in WinForm app

    - by msorens
    I have worked with globalization settings in the past but not within the .NET environment, which is the topic of this question. What I am seeing is most certainly due to knowledge I have yet to learn so I would appreciate illumination on the following. Setup: My default language setting is English (en-us specifically). I added a second language (Danish) on my development system (WinXP) and then opened the language bar so I could select either at will. I selected Danish on the language bar then opened Notepad and found the language reverted to English on the language bar. I understand that the language setting is per application, so it seemed that Notepad set the default back to English. (I found that strange since Windows and thus Notepad is used all over the world.) Closing Notepad returned the setting on the language bar to Danish. I then launched my open custom WinForm application--which I know does not set the language--and it also reverted from English to Danish when opened, then back to Danish when terminated! Question #1A: How do I get my WinForm application upon launch to inherit the current setting of the language bar? My experiment seems to indicate that each application starts with the system default and requires the user to manually change it once the app is running--this would seem to be a major inconvenience for anyone that wants to work with more than one language! Question #1B: If one must, in fact, set the language manually in a multi-language scenario, how do I change my default system language (e.g. to Danish) so I can test my app's launch in another language? I added a display of the current language in my application for this next experiment. Specifically I set a MouseEnter handler on a label that set its tooltip to CultureInfo.CurrentCulture.Name so each time I mouse over I thought I should see the current language setting. Since setting the language before I launch my app did not work, I launched it then set the language to Danish. I found that some things (like typing in a TextBox) did honor this Danish setting. But mousing over the instrumented label still showed en-us! Question #2A: Why does CultureInfo.CurrentCulture.Name not reflect the change from my language bar while other parts of my app seem to recognize the change? (Trying CultureInfo.CurrentUICulture.Name produced the same result.) Question #2B: Is there an event that fires upon changes on the language bar so I could recognize within my app when the language setting changes?

    Read the article

  • How do you word wrap a RichTextField for Blackberry

    - by Kai
    I've been trying to modify a rich text field to display correctly in its half of the horizontal field. The goal is this: --------------------------- | address is | ***********| | very long | ** IMAGE **| | state, zip | ***********| --------------------------- Where address is a single string separate from the city and zip. I am modifying the address field like this: RichTextField addrField = new RichTextField(address) { public int getPreferredWidth() { return 200; } protected void layout(int maxWidth,int maxHeight) { super.layout(getPreferredWidth(),maxHeight); setExtent(getPreferredWidth(), getHeight()); } }; The results look like this: ----------------------------- | address is ve| ***********| | state, zip | ** IMAGE **| | | ***********| ----------------------------- where clearly the address is just going under the image. Both horizontal fields are static 200 pixels wide. It's not like the system wouldn't know where to wrap the address. However, I have heard it is not easy to do this and is not done automatically. I have had no success finding a direct answer online. I have found people saying you need to do it in a custom layout manager, some refer to the RichTextField API, which is of no use. But nobody actually mentions how to do it. I understand that I may need to read character by character and set where the line breaks should happen. What I don't know is how exactly to do any of this. You can't just count characters and assume each is worth 5 pixels, and you shouldn't have to. Surely there must be some way to achieve this in a way that makes sense. Any suggestions?

    Read the article

  • Forwarding an email with python smtplib

    - by robbles
    I'm trying to put together a script that automatically forwards certain emails that match a specific criteria to another email. I've got the downloading and parsing of messages using imaplib and email working, but I can't figure out how to forward an entire email to another address. Do I need to build a new message from scratch, or can I somehow modify the old one and re-send it? Here's what I have so far (client is an imaplib.IMAP4 connection, and id is a message ID): status, data = client.fetch(id, '(RFC822)') email_body = data[0][1] mail = email.message_from_string(email_body) # ...Process message... # This doesn't work forward = email.message.Message() forward.set_payload(mail.get_payload()) forward['From'] = '[email protected]' forward['To'] = '[email protected]' smtp.sendmail(user, ['[email protected]'], forward.as_string()) I'm sure there's something slightly more complicated I need to be doing with regard to the MIME content of the message. Surely there's some simple way of just forwarding the entire message though? # This doesn't work either, it just freezes...? mail['From'] = '[email protected]' mail['To'] = '[email protected]' smtp.sendmail(user, ['[email protected]'], mail.as_string())

    Read the article

  • $1 vs \1 in Perl regex substitutions

    - by Mr Foo Bar
    I'm debugging some code and wondered if there is any practical difference between $1 and \1 in Perl regex substitutions For example: my $package_name = "Some::Package::ButNotThis"; $package_name =~ s{^(\w+::\w+)}{$1}; print $package_name; # Some::Package This following line seems functionally equivalent: $package_name =~ s{^(\w+::w+)}{\1}; Are there subtle differences between these two statements? Do they behave differently in different versions of Perl?

    Read the article

  • Why does my Workflow Service (4.0) variable go null in a DoWhile Activity?

    - by jlafay
    I have a WF service that I'm trying to setup receive activities to "Subscribe" and "Unsubscribe". I'm using This WF Durable Duplex Tutorial as a basis because my service performs callbacks to clients. Basically, think of it as a chat service. I can make client calls to the two receive activities just fine. What happens is the callback address of the client is passed in to Subscribe() on the service. The address is stored as a variable in the WF service and everything looks like it would work as to be expected. When a client calls Unsubscribe(), my watch I have set on the address var during debugging shows it as null. So what gives? Here's the basic setup of my WF service layout... Everything is enveloped in a DoWhile activity. Inside of that is a Pick activity and two Pick branches. The first branch is for subscribing activities. It has a receive-sendreply activity that assigns the string passed by the client to the WF address var. The second branch handles unsubscribing. The trigger is the Request activity and the client address is again passed in. From there it goes into a sequence, starting with an If. It checks to see if the unsubscribeAddress equals the address already subscribed. If it does, then it sets the address to String.Empty and sends a success message back to the client. Why would a variable that's scoped to the enveloping DoWhile activity be implicitly assigned to null? I'm trying to get this to work so I can implement multiple client subscribers from there and work on triggers that invoke callbacks to multiple clients. CONCAT EDIT: I set a breakpoint at the DoWhile level and my var is null once Unsubscribe() is called. When Subscribe() is invoked, the watch shows a value in the var all the way through. Until I Unsubscribe() with a client. Should I be using a While Activity instead?

    Read the article

  • How to serialize a protected property in wcf

    - by Denis Rosca
    Hello everyone, I have to classes (Person and Address) that i need to send via wcf, the classes look like this: public class PersoanaFizica :IExtensibleDataObject { [DataMember] private Guid _id; [DataMember(Name = "Id")] protected virtual Guid Id { get { return _id; } set { _id = value; } } private ExtensionDataObject _extensionData; public virtual ExtensionDataObject ExtensionData { get { return _extensionData; } set { _extensionData = value; } } private string _firstName; [Searchable(PropertyName="FirstName")] [DataMember] public virtual string FirstName { get { return this._firstName; } set { this._firstName = value; } } private string _lastName; [Searchable(PropertyName="LastName")] [DataMember] public virtual string LastName { get { return this._lastName; } set { this. _lastName = value; } } private Address _address; [Searchable(PropertyName="Address")] [DataMember] public virtual Address Address { get { return this._address; } set { this._address = value; } } } public class Address : IExtensibleDataObject { [DataMember] private Guid _id; [DataMember] public virtual Guid Id { get { return _id; } set { _id = value; } } private ExtensionDataObject _extensionData; public virtual ExtensionDataObject ExtensionData { get { return _extensionData; } set { _extensionData = value; } } private string _country; [Searchable(PropertyName="Country")] [DataMember] public virtual string Country { get { return this._country; } set { this._country = value; } } // and some other properties related to the address } The problem is that when i try to send them via wcf, the client recieves the Id properties set to 00000-0000-00000-00000 or smth like this. Any idea why this is happening? And how to serialize the proper values? Thanks,Denis.

    Read the article

  • How do gitignore exclusion rules actually work?

    - by meowsqueak
    I'm trying to solve a gitignore problem on a large directory structure, but to simplify my question I have reduced it to the following. I have the following directory structure of two files (foo, bar) in a brand new git repository (no commits so far): a/b/c/foo a/b/c/bar Obviously, a 'git status -u' shows: # Untracked files: ... # a/b/c/bar # a/b/c/foo What I want to do is create a .gitignore file that ignores everything inside a/b/c but does not ignore the file 'foo'. If I create a .gitignore thus: c/ Then a 'git status -u' shows both foo and bar as ignored: # Untracked files: ... # .gitignore Which is as I expect. Now if I add an exclusion rule for foo, thus: c/ !foo According to the gitignore manpage, I'd expect this to to work. But it doesn't - it still ignores foo: # Untracked files: ... # .gitignore This doesn't work either: c/ !a/b/c/foo Neither does this: c/* !foo Gives: # Untracked files: ... # .gitignore # a/b/c/bar # a/b/c/foo In that case, although foo is no longer ignored, bar is also not ignored. The order of the rules in .gitignore doesn't seem to matter either. This also doesn't do what I'd expect: a/b/c/ !a/b/c/foo That one ignores both foo and bar. One situation that does work is if I create the file a/b/c/.gitignore and put in there: * !foo But the problem with this is that eventually there will be other subdirectories under a/b/c and I don't want to have to put a separate .gitignore into every single one - I was hoping to create 'project-based' .gitignore files that can sit in the top directory of each project, and cover all the 'standard' subdirectory structure. This also seems to be equivalent: a/b/c/* !a/b/c/foo This might be the closest thing to "working" that I can achieve, but the full relative paths and explicit exceptions need to be stated, which is going to be a pain if I have a lot of files of name 'foo' in different levels of the subdirectory tree. Anyway, either I don't quite understand how exclusion rules work, or they don't work at all when directories (rather than wildcards) are ignored - by a rule ending in a / Can anyone please shed some light on this? Is there a way to make gitignore use something sensible like regular expressions instead of this clumsy shell-based syntax? I'm using and observe this with git-1.6.6.1 on Cygwin/bash3 and git-1.7.1 on Ubuntu/bash3.

    Read the article

  • Can ping device from one computer and not the other

    - by Sean Duggan
    I've recently been assigned to work on a diagnostic program done in C++ which communicates with a piece of electronic equipment. Our normal scenario involves communicating via an RS232 interface, but I've been asked to make our program work over ethernet, source code having been done in Visual Basic. After much thrashing about trying to get the code to work and continuing to get 10049 Winsock errors when I tried to connect, I tried pinging the switch. From the computer the VB program is running on, I can see the switch via ping, nslookup, tracert, and pathping (I was going down the list of programs) and I can do this via URI or IP address. From my laptop, sending the same commands fails every time. They're both using the same network cable and the same USB-to-Ethernet device (I've been swapping them between tests) but one can see the switch and the other cannot. I'm working on the programming end, but the ping results makes me think that there might be a network issue stymieing me. wry grin I'm not much of a network guy, so I'm appealing to expert assistance. Both computers are running Windows XP if that helps. The connection is to an "IP-RS8" device which then connects to our VCU-C units. Each unit is accessible via URI or IP address on the desktop computer we usually have connected to the units (it's running the older VB program that I was asked to lift the networking code from). The connection is made via a USB-to-Ethernet adapter so as to leave the regular Ethernet port available for connecting to the company network. Hmm... come to think of it, I've probably been confusing the issue, talking about pinging "the switch" rather than indicating that it's the devices. My apologies. Communication is generally done with a DLL that uses Winsock functions to make queries for data from the VCU and then to receive. I'm failing when connecting. I haven't found anything on the firewall which should block these commands, but I'll keep poking. I don't know if it's potentially relevant, but on the desktop, the adapter maps to Local Area Connection 3 while on the laptop, it consistently maps to Local Area Connection 2. Currently reading up on DHCP. IPConfig /all results: Desktop Host Name . . . . . . . . . . . . : AMERDAEXXXXXX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Broadcom NetXtreme XYxx Gigabit Controller Physical Address. . . . . . . . . : YY-XX-YB-XX-XX-XX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XXX Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XY:XX:XX AM Ethernet adapter Local Area Connection X: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX axYYYYX USBX.Y to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XY.Y.Y.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XY.Y.Y.X DHCP Server . . . . . . . . . . . : XY.Y.Y.XY DNS Servers . . . . . . . . . . . : XY.Y.Y.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XY:XX:XY AM Lease Expires . . . . . . . . . . : Tuesday, August YX, XYXX XX:XY:XY AM Laptop Windows IP Configuration Host Name . . . . . . . . . . . . : AMERLAFYYXXYX Primary Dns Suffix . . . . . . . : amer.example.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : COMPANY.com amer.example.com atle.example.com cone.example.com apac.example.com scan.example.com bYX.example.com Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : amer.example.com Description . . . . . . . . . . . : Intel(R) 82567LM Gigabit Network Connection Physical Address. . . . . . . . . : YY-XY-BY-DY-XB-YX Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : XYY.XXX.XY.XY Subnet Mask . . . . . . . . . . . : XXX.XXX.XXY.Y Default Gateway . . . . . . . . . : XYY.XXX.XY.X DHCP Server . . . . . . . . . . . : XY.XXX.XXY.XX DNS Servers . . . . . . . . . . . : XY.XXX.XXY.XX XY.XXY.XXY.XX Primary WINS Server . . . . . . . : XY.XXX.XXY.X Secondary WINS Server . . . . . . : XY.XXY.XXY.X Lease Obtained. . . . . . . . . . : Thursday, July XX, XYXX XX:XX:XX AM Lease Expires . . . . . . . . . . : Sunday, July XX, XYXX XX:XX:XX AM Ethernet adapter {XYXAAYXX-YEDY-XXYX-YYEX-BYXYXXYEEYEX}: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Nortel IPSECSHM Adapter - Packet Scheduler iniport Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-YY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : Y.Y.Y.Y Subnet Mask . . . . . . . . . . . : Y.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Leaf Networks Adapter: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Leaf Networks Adapter Physical Address. . . . . . . . . : YY-FF-FA-BC-YF-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : X.XYY.XY.XX Subnet Mask . . . . . . . . . . . : XXX.Y.Y.Y Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : YY-FX-AX-YA-BY-CA Ethernet adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) WiFi Link 5300 AGN Physical Address. . . . . . . . . : YY-XX-YA-CX-FC-YE Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : ASIX ax88772 USB2.0 to Fast Ethernet Adapter Physical Address. . . . . . . . . : YY-XY-BY-YX-XY-AY Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : XYX.XYY.X.X Subnet Mask . . . . . . . . . . . : XXX.XXX.XXX.Y Default Gateway . . . . . . . . . :

    Read the article

  • Referencing Environment Variables in web.xml

    - by Udi Bar-On
    I'm pre-packaging a JSP web-app that relies on some file path settings found within web.xml. These settings are unknown at packaging time, because they reference a path the customer will set when deploying the entire application (of which the web-app is a management interface). It seems that the easiest way to avoid tokens and file modifications in my installer script, is to ask the user for an install location, set this location as an environment variable (e.g JAVA_HOME), and have web.xml always reference that variable. Is there a way to reference an environment variable value from within web.xml? Google searches lead to the J2EE method of SETTING environment variables from ejb xml files. This is not what I'm looking for. Thanks Udi

    Read the article

  • How can I use functools.partial on multiple methods on an object, and freeze parameters out of order

    - by Joseph Garvin
    I find functools.partial to be extremely useful, but I would like to be able to freeze arguments out of order (the argument you want to freeze is not always the first one) and I'd like to be able to apply it to several methods on a class at once, to make a proxy object that has the same methods as the underlying object except with some of its methods parameter being frozen (think of it as generalizing partial to apply to classes). I've managed to scrap together a version of functools.partial called 'bind' that lets me specify parameters out of order by passing them by keyword argument. That part works: >>> def foo(x, y): ... print x, y ... >>> bar = bind(foo, y=3) >>> bar(2) 2 3 But my proxy class does not work, and I'm not sure why: >>> class Foo(object): ... def bar(self, x, y): ... print x, y ... >>> a = Foo() >>> b = PureProxy(a, bar=bind(Foo.bar, y=3)) >>> b.bar(2) Traceback (most recent call last): File "<stdin>", line 1, in <module> TypeError: bar() takes exactly 3 arguments (2 given) I'm probably doing this all sorts of wrong because I'm just going by what I've pieced together from random documentation, blogs, and running dir() on all the pieces. Suggestions both on how to make this work and better ways to implement it would be appreciated ;) One detail I'm unsure about is how this should all interact with descriptors. Code follows. from types import MethodType class PureProxy(object): def __init__(self, underlying, **substitutions): self.underlying = underlying for name in substitutions: subst_attr = substitutions[name] if hasattr(subst_attr, "underlying"): setattr(self, name, MethodType(subst_attr, self, PureProxy)) def __getattribute__(self, name): return getattr(object.__getattribute__(self, "underlying"), name) def bind(f, *args, **kwargs): """ Lets you freeze arguments of a function be certain values. Unlike functools.partial, you can freeze arguments by name, which has the bonus of letting you freeze them out of order. args will be treated just like partial, but kwargs will properly take into account if you are specifying a regular argument by name. """ argspec = inspect.getargspec(f) argdict = copy(kwargs) if hasattr(f, "im_func"): f = f.im_func args_idx = 0 for arg in argspec.args: if args_idx >= len(args): break argdict[arg] = args[args_idx] args_idx += 1 num_plugged = args_idx def new_func(*inner_args, **inner_kwargs): args_idx = 0 for arg in argspec.args[num_plugged:]: if arg in argdict: continue if args_idx >= len(inner_args): # We can't raise an error here because some remaining arguments # may have been passed in by keyword. break argdict[arg] = inner_args[args_idx] args_idx += 1 f(**dict(argdict, **inner_kwargs)) new_func.underlying = f return new_func

    Read the article

  • How do I add a column that displays the number of distinct rows to this query?

    - by Fake Code Monkey Rashid
    Hello good people! I don't know how to ask my question clearly so I'll just show you the money. To start with, here's a sample table: CREATE TABLE sandbox ( id integer NOT NULL, callsign text NOT NULL, this text NOT NULL, that text NOT NULL, "timestamp" timestamp with time zone DEFAULT now() NOT NULL ); CREATE SEQUENCE sandbox_id_seq START WITH 1 INCREMENT BY 1 NO MINVALUE NO MAXVALUE CACHE 1; ALTER SEQUENCE sandbox_id_seq OWNED BY sandbox.id; SELECT pg_catalog.setval('sandbox_id_seq', 14, true); ALTER TABLE sandbox ALTER COLUMN id SET DEFAULT nextval('sandbox_id_seq'::regclass); INSERT INTO sandbox VALUES (1, 'alpha', 'foo', 'qux', '2010-12-29 16:51:09.897579+00'); INSERT INTO sandbox VALUES (2, 'alpha', 'foo', 'qux', '2010-12-29 16:51:36.108867+00'); INSERT INTO sandbox VALUES (3, 'bravo', 'bar', 'quxx', '2010-12-29 16:52:36.370507+00'); INSERT INTO sandbox VALUES (4, 'bravo', 'foo', 'quxx', '2010-12-29 16:52:47.584663+00'); INSERT INTO sandbox VALUES (5, 'charlie', 'foo', 'corge', '2010-12-29 16:53:00.742356+00'); INSERT INTO sandbox VALUES (6, 'delta', 'foo', 'qux', '2010-12-29 16:53:10.884721+00'); INSERT INTO sandbox VALUES (7, 'alpha', 'foo', 'corge', '2010-12-29 16:53:21.242904+00'); INSERT INTO sandbox VALUES (8, 'alpha', 'bar', 'corge', '2010-12-29 16:54:33.318907+00'); INSERT INTO sandbox VALUES (9, 'alpha', 'baz', 'quxx', '2010-12-29 16:54:38.727095+00'); INSERT INTO sandbox VALUES (10, 'alpha', 'bar', 'qux', '2010-12-29 16:54:46.237294+00'); INSERT INTO sandbox VALUES (11, 'alpha', 'baz', 'qux', '2010-12-29 16:54:53.891606+00'); INSERT INTO sandbox VALUES (12, 'alpha', 'baz', 'corge', '2010-12-29 16:55:39.596076+00'); INSERT INTO sandbox VALUES (13, 'alpha', 'baz', 'corge', '2010-12-29 16:55:44.834019+00'); INSERT INTO sandbox VALUES (14, 'alpha', 'foo', 'qux', '2010-12-29 16:55:52.848792+00'); ALTER TABLE ONLY sandbox ADD CONSTRAINT sandbox_pkey PRIMARY KEY (id); Here's the current SQL query I have: SELECT * FROM ( SELECT DISTINCT ON (this, that) id, this, that, timestamp FROM sandbox WHERE callsign = 'alpha' AND CAST(timestamp AS date) = '2010-12-29' ) playground ORDER BY timestamp DESC This is the result it gives me: id this that timestamp ----------------------------------------------------- 14 foo qux 2010-12-29 16:55:52.848792+00 13 baz corge 2010-12-29 16:55:44.834019+00 11 baz qux 2010-12-29 16:54:53.891606+00 10 bar qux 2010-12-29 16:54:46.237294+00 9 baz quxx 2010-12-29 16:54:38.727095+00 8 bar corge 2010-12-29 16:54:33.318907+00 7 foo corge 2010-12-29 16:53:21.242904+00 This is what I want to see: id this that timestamp count ------------------------------------------------------------- 14 foo qux 2010-12-29 16:55:52.848792+00 3 13 baz corge 2010-12-29 16:55:44.834019+00 2 11 baz qux 2010-12-29 16:54:53.891606+00 1 10 bar qux 2010-12-29 16:54:46.237294+00 1 9 baz quxx 2010-12-29 16:54:38.727095+00 1 8 bar corge 2010-12-29 16:54:33.318907+00 1 7 foo corge 2010-12-29 16:53:21.242904+00 1 EDIT: I'm using PostgreSQL 9.0.* (if that helps any).

    Read the article

  • Generating unique N-valued key

    - by Bar
    Hi, StackOverflow! I want to generate unique random, N-valued key. This key can contain numbers and latin characters, i.e. A-Za-z0-9. The only solution I am thinking about is something like this (pseudocode): key = ""; smb = "ABC…abc…0123456789"; // allowed symbols for (i = 0; i < N; i++) { key += smb[rnd(0, smb.length() - 1)]; // select symbol at random position } Is there any better solution? What can you suggest? TIA, Michael.

    Read the article

  • TSQL - How to join 1..* from multiple tables in one resultset?

    - by ElHaix
    A location table record has two address id's - mailing and business addressID that refer to an address table. Thus, the address table will contain up to two records for a given addressID. Given a location ID, I need an sproc to return all tbl_Location fields, and all tbl_Address fields in one resultset: LocationID INT, ClientID INT, LocationName NVARCHAR(50), LocationDescription NVARCHAR(50), MailingAddressID INT, BillingAddressID INT, MAddress1 NVARCHAR(255), MAddress2 NVARCHAR(255), MCity NVARCHAR(50), MState NVARCHAR(50), MZip NVARCHAR(10), MCountry CHAR(3), BAddress1 NVARCHAR(255), BAddress2 NVARCHAR(255), BCity NVARCHAR(50), BState NVARCHAR(50), BZip NVARCHAR(10), BCountry CHAR(3) I've started by creating a temp table with the required fields, but am a bit stuck on how to accomplish this. I could do sub-selects for each of the required address fields, but seems a bit messy. I've already got a table-valued-function that accepts an address ID, and returns all fields for that ID, but not sure how to integrate it into my required result. Off hand, it looks like 3 selects to create this table - 1: Location, 2: Mailing address, 3: Billing address. What I'd like to do is just create a view and use that. Any assistance would be helpful. Thanks.

    Read the article

  • Horizontally align rows in multiple tables using web user control

    - by goku_da_master
    I need to align rows in different tables that are layed out horizontally. I'd prefer to put the html code in a single web user control so I can create as many instances of that control as I want and lay them out horizontally. The problem is, the text in the rows needs to wrap. So some rows may expand vertically and some may not (see the example below). When that happens, the rows in the other tables aren't aligned horizontally. I know I can accomplish all this by using a single table, but that would mean I'd have to duplicate the name, address and phone html code instead of dynamically creating new instances of my user control (in reality there are many more fields than this, but I'm keeping it simple). Is there any way to do this whether with div's, tables or something else? Here's the problem: Mary Jane's address field expands 2 lines, causing her phone field to not align properly with John's and Bob's. Name: John Doe Name: Mary Jane Name: Bob Smith Address: 123 broadway Address: Some really long address Address: Short address Phone: 123-456 that takes up multiple lines Phone: 111-2222 Phone: 456-789 I'm not restricted in any way how to do this (other than using asp.net), but I'd prefer to use a single web control that I instantiate X times at design time (in this example, it's 3 times). I'm using VS2008, and .Net 3.5

    Read the article

  • Get the selected option id with jQuery

    - by Itamar Bar-Lev
    Hi, I'm trying to use jQuery to make an ajax request based on a selected option. Is there a simple way to retrieve the selected option id (e.g. "id2") using jQuery? <select id="my_select"> <option value="o1" id="id1">Option1</option> <option value="o2" id="id2">Option2</option> </select> $("#my_select").change(function() { //do something with the id of the selected option });

    Read the article

  • .NET MVC custom routing with empty parameters

    - by user135498
    Hi All, I have a .net mvc with the following routes: routes.Add(new Route( "Lookups/{searchtype}/{inputtype}/{firstname}/{middlename}/{lastname}/{city}/{state}/{address}", new RouteValueDictionary( new { controller = "Lookups", action = "Search", firstname = (string)null, middlename = (string)null, lastname = (string)null, city = (string)null, state = (string)null, address = (string)null, SearchType = SearchType.PeopleSearch, InputType = InputType.Name }), new MvcRouteHandler()) ); routes.Add(new Route( "Lookups/{searchtype}/{inputtype}", new RouteValueDictionary( new { controller = "Lookups", action = "Search", firstname = "", middlename = "", lastname = "", city = "", state = "", address = "" }), new MvcRouteHandler()) ); routes.Add(new Route( "Lookups/{searchtype}/{inputtype}", new RouteValueDictionary( new { controller = "Lookups", action = "Search", firstname = "", middlename = "", lastname = "", city = "", state = "", address = "", SearchType = SearchType.PeopleSearch, InputType = InputType.Name }), new MvcRouteHandler()) ); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Account", action = "LogOn", id = "" } // Parameter defaults ); The following request works fine: http://localhost:2608/Lookups/PeopleSearch/Name/john/w/smith/seattle/wa/123 main This request does not work: http://localhost:2608/Lookups/PeopleSearch/Name/john//smith//wa/ Not all requests will have all paramters and I would like empty parameters to be passed to the method as empty string or null. Where am I going wrong? The method: public ActionResult Search(string firstname, string middlename, string lastname, string city, string state, string address, SearchType searchtype, InputType inputtype) { SearchRequest r = new SearchRequest { Firstname = firstname, Middlename = middlename, Lastname = lastname, City = city, State = state, Address = address, SearchType = searchtype, InputType = inputtype }; return View(r); }

    Read the article

  • Handling PHP exceptions with JQuery

    - by Itamar Bar-Lev
    Hello, I'm using JQuery to call a PHP function that returns a JSON string upon success or throws some exceptions. Currently I'm calling jQuery.parseJSON() on the response and if it fails I assume the response contains an exception string. $.ajax({ type: "POST", url: "something.php", success: function(response){ try { var json = jQuery.parseJSON(response); } catch (e) { alert(response); return -1; } // ... do stuff with json } Can anyone suggest a more elegant way to catch the exception? Many thanks, Itamar

    Read the article

  • regex to format a float in php

    - by Itamar Bar-Lev
    I have a PHP function for formatting a float to a given amount of decimal points that uses number_format(), and then removes the unneeded zeros (and also the '.' if possible): $float = number_format($float, $decimalPlaces, '.', ''); for ($i = 0; $i < $decimalPlaces; $i++) { if (substr($float, strlen($float) - 1, strlen($float)) == '0') { $float = substr($float, 0, strlen($float) - 1); } } if (substr($float, strlen($float) - 1, strlen($float)) == '.') { $float = substr($float, 0, strlen($float) - 1); } Is it possible to do so more effectively with a regular expression?

    Read the article

  • Spring MVC + Hibernate encoding problem

    - by Bar
    I work on Spring MVC + Hibernate application, use MySQL (ver. 5.0.51a) with the InnoDB engine. The problem appears when I am sending a form with cyrillic characters. As the result, database contains senseless chars in unknown encoding. All the JSP pages, database (+ tables and fields) created using UTF-8. Hibernate config also contains property which sets encoding to UTF-8. I had solved this by creating filter which encodes request content with UTF-8. Exemplary code: … encoding = "UTF-8"; request.setCharacterEncoding(encoding); chain.doFilter(request, response); … But it visibly slows down the app. The interesting thing is that executing insert query directly from the app (i.e. running from Eclipse as Java Application) works perfect. Any suggestions are welcome. TIA, Michael.

    Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >