Search Results

Search found 11903 results on 477 pages for 'ip forwarding'.

Page 144/477 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Which ports to open on domain vs internet

  - by zsharp

  I have a web server/database/domainController. I notice that ports 137 and 138 on the public IP AND private IP are open on all machines there are also other open ports on 0.0.0.0.(ie. 135, 2002) Can and should I close 137-139 on the public IP only? will that interfere with any services.

  Read the article

• Swapping out a hardware firewall does the mac address get cached?

  - by Dan

  We need to replace a hardware firewall (cisco pix) and have a spare that we will use (temporarily). The firewall sits in front of a couple of web-servers colocated at a data-centre. The replacement will be configured with identical settings (external/internal IP addresses, configured ports etc.). When we swap the firewalls over, will this work immediately or will the old Pix's mac address be cached and the new firewall not be seen until the cache is cleared? (What is it though that is caching the address? Is it just the switch/router that our pix is connected to?) Reason for asking is a few years ago I had a smoothwall firewall in front of a lone server (the external IP of the smoothwall was also the external IP of the web-server). When I replaced the smoothwall with a pix, the IP address of the web-server stayed the same but it now had to be reached via the new firewall on a different IP. It took about 2-4 hours before the rest of the world could see that web-server again. I'm hoping for less downtime this time!

  Read the article

• pix 501, static route to d-link router (different subnet)

  - by ra170

  I have pix 501 cisco firewall with internal ip 192.168.10.1. I have connected d-link router (dir-655) to pix 501. The d-link router has internal ip 192.168.0.1 The picture would like something like that: |pix 501| has 192.168.10.1 ip |DIR-655| has 192.168.0.1 ip 1. |cable modem|----|pix 501|-------|DIR-655|-----PC 2. PC--------|pix 501|---------|DIR-655| | | |cable modem| When I'm on the wireless network (dir-655) with assigned ip of 192.168.0.x I can cross the subnet and connect to my firewall 192.168.10.1. (pic. 1) The problem is that if I'm on the 192.168.10.x network I can't connect to anything over at 192.168.0.x network. (pic.2) I've tried entering a static route like this: `route inside 192.168.0.0 255.255.255.0 192.168.10.1 1` I also tried assigning static ip to wan interface on DIR-655 to 192.168.10.30 and then tried this: route inside 192.168.0.0 255.255.255.0 192.168.10.30 1 But still, can't connect to 192.168.0.1 or anything on that subnet. Is there a way to setup a static route? Would adding a separate router between PIX 501 and DIR-655 help? I would think that static route like this should take care of it, but it doesn't. This is my route config and nat: (config)# sh route outside 0.0.0.0 0.0.0.0 (outside_IP) 1 DHCP static outside (outside_IP) 255.255.248.0 (outside_IP) 1 CONNECT static inside 192.168.0.0 255.255.255.0 192.168.10.1 1 OTHER static inside 192.168.10.0 255.255.255.0 192.168.10.1 1 CONNECT static or (route inside 192.168.0.0 255.255.255.0 192.168.10.30 1) (config)# sh nat nat (inside) 1 192.168.1.0 255.255.255.0 0 0 nat (inside) 1 192.168.10.0 255.255.255.0 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 I ended up turning DIR-655 into an Access Point (turning off DHCP and pluging cable from PIX lan interface into one of the LAN interfaces on DIR-655, and leaving WAN port empty), that works as far as DIR-655 being on the same subnet now, and I can access every machine. However the question is, why can't I simply route between those two? would router between these two help? One of the reasons is, that the PIX 501 has only 10 licences, so now I'm using almost all of them. (I have few computers, iphones, ps3, print server, etc.) I would really appreciate some help! Thanks.

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• What settings need to be changed to allow EC2 instances to use Amazon's Route 53 for DNS?

  - by ks78

  I have a number of Amazon EC2 instances, all running Ubuntu, which I'd like to configure to use Amazon's Route 53. I setup a script, following Shlomo Swidler's article, but ran into script-related issues, which were answered here. Now, I have the script working, but my instances are still not able to access Route 53's DNS. By this I mean, they are not able to resolve hostnames to IP addresses. My instances are currently configured with the DNS server IP address Amazon pushes out to them by default, does that need to be changed when using Route 53? I'm also IP-restricting my instances using the Security Groups. Could that be the problem? Is there a certain IP address or port I should open to allow communication with Route 53? It seems that DNS requests should be originating from my instances so the Security Groups shouldn't be an issue, but I've been wrong before. If anyone has any ideas, I'd really appreciate it.

  Read the article

• LACP : Cisco ASA 5515 & Switch ProCurve 2920

  - by user979276

  I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

  Read the article

• Email hosting on home's Windows server 2003

  - by klay

  Hi guys, I am new to Server management, I have a static Ip address and I bought recently a domain name, I configure the domain name to target my Ip address. I am running windows server 2003 standard. what are the steps to host my email adresses? Do I need to buy anything else, or what I have is enough (static ip address, domain name, win server 2003, exchange server 2003) ?? thanks Guys

  Read the article

• would a dynamic wan disrupt a static lan?

  - by JohnMerlino

  So I found out that the cable company use the DHCP to assign the public ip address dynamically. So a subscriber's public facing ip address can change during the length of their subscription. Now what if you remove DHCP on a particular computer, which you plan to use as a web server, so that the machine has a static, unchanging IP address. If the public ip address was to change, would this confuse the Network Address Translation (NAT) and cause some sort of disruption? Please answer in layman terms, as I'm still grasping concepts here. thanks.

  Read the article

• Ping and crawling not working, site still resolving

  - by Andrew Alexander

  Ok, so we're trying to figure out why the site of one of our clients isn't being crawled by Google (we've ruled out robots.txt or meta tags) When we go to the site, either IP address or domain name, the site resolves, everything works. However, Google is getting a 302 redirect (which it apparently isn't following for crawling), and when we ping the address, it times out (note, the site is still resolving in the browser throughout all of this). The site is built in ASP.Net (I assume C#) and so my thoughts were that it was an errant redirect rule, or some other sort of server side issue. We also thought that it might be due to incorrect domain pointing (but if we try to ping the IP, it doesn't work, so that sorta rules that out). We're really not sure what is causing all of these errors, or even if they have one single source. Anyone have any ideas what could be going on? Do you need any more information? To boil it down in a TL; dr: * Site resolving in browser, both IP and domain name. No problems here. * Site not being crawled by Google (gets a 302 it doesn't seem to follow) - it is not due to robots.txt or meta tags * Ping is not working for the IP address. This is very odd, because again, the IP address seems to work fine in the browser. * Our thoughts are either redirect rule issue, domain pointing issue, or possibly some errant code - or some combination of the three

  Read the article

• Someone used or hacked my computer to commit a crime? what defense do I have?

  - by srguws

  Hello, I need IMMEDIATE Help on a computer crime that I was arrested for. It may involve my computer, my ip, and my ex-girlfriend being the true criminal. The police do not tell you much they are very vague. I was charged though! So my questions are: -If someone did use my computer at my house and business and post a rude craigslist ad about a friend of my girlfriend at the time from a fake email address, how can I be the ONLY one as a suspect. Also how can I be charged. I noticed the last few days there are many ways to use other peoples computers, connections, etc. Here are a few things I found: You can steal or illegally use an ip addresss or mac address. Dynamic Ip is less secure and more vulnerable than static. People can sidejack and spoof your Mac, Ip, etc. There is another thing called arp spoofing. I am sure this is more things, but how can I prove that this happened to me or didnt happen to me. -The police contacted Craigslist, the victim, aol, and the two isp companies. They say they traced the IP's to my business and my home. My ex was who I lived with and had a business with has access to the computers and the keys to bothe buildings. My brother also lives and works with me. My business has many teenagers who use the computer and wifi. My brother is a college kid and also has friends over the house and they use the computer freely. So how can they say it was me because of an angry ex girlfriend.

  Read the article

• Installing SSL certs with nginx on Amazon EC2

  - by Ethan

  I finally got a cert from an authority and am struggling to get things working. I've created the appropriate combined certificate (personal + intermediate + root) and nginx is pointing to it. I got an elastic IP and connected it to my EC2 instance. My DNS records point to that IP. But when I point the browser to the hostname, I get the standard "Connection Untrusted" bit, with ssl_error_bad_cert_domain. Port 443 is open - I can get to the site over https if I ignore the warning. Weird thing is, under technical details, it lists the domain I tried to access as valid! When I try and diagnose with ssl testing sites, they don't even detect a certificate! What am I missing here? domain is yanlj.coinculture.info. Note I've got coinculture.info running on a home server without a dedicated IP and have the same problem, but I'll be moving that to the same EC2 instance as soon as I figure this thing out. I thought the elastic IP would solve things but it hasn't

  Read the article

• Why the VPN Network Shake-Up?

  - by Brent Arias

  I can RDP to another machine on my home network, only if I'm not also hooked up to my employer's VPN with the Cisco VPN client. Indeed, I can't even ping the other machine by name in this mode, because ICMP suddenly thinks that ( ping myMachine ) now means ( ping myMachine.myEmployer.com ). Of course there is no machine by that latter name, and so it fails. Even weirder, once I disconnect from the VPN I can again ping myMachine successfully, but ICMP reports the machine by its MAC address instead of its IP address. I don't think I've ever seen ping identify another machine by its MAC address. So two questions: How can I access via RDP/ping the other machine BY NAME on my local network while also connected to the VPN? Why is ping identifying a MAC address for the machine on my home network, instead of an IP address? And how can I change this so that an IP address is reported instead? For question #1, I can indeed access the other machine on my home network by IP address. I suspect if I put the name-IP pair into my HOSTS file, then I would be able to access it even when connected to the VPN. But I wonder if there is another (more elegant) solution?

  Read the article

• How to forward email to my Gmail account with GoDaddy?

  - by Mr. Flibble

  I've just got a new domain with GoDaddy. I want to forward email to various addresses to different Gmail addresses. I can't find this option in the GoDaddy control panel. The clostest thing I can see is a link to buy an email forwarding package. Do they actually charge extra to set up email forwarding!? Are there any ways to forward it for free?

  Read the article

• Make 2 virtual machines ping in virtual box

  - by darkheir

  I'm trying to make 2 virtual machines communicate in Virtual Box, but whitout any success. Here are the step I have done: I setted both VMs in Internal networking mode (using VBoxManage modifyvm "VM name" --nic<x> intnet) I setted the DHCP server that is built into VirtualBox to manage IP addresses :VBoxManage dhcpserver add --netname intnet --ip 10.13.13.100 --netmask 255.255.255.0 --lowerip 10.13.13.101 --upperip 10.13.13.254 --enable But then both of the VM have the same IP Adresse (10.13.13.101) and even if set the IP manually, the Virtual Machines are not pinging each other.

  Read the article

• Multiple VLANs in the same subnet

  - by A.J.

  Is it possible to have multiple VLANs in the same subnet, with the same gateway address (TMG)? I want to avoid having many Subnets (and vNIC's in TMG) just to isolate sets of a few hosts. IP: 10.0.0.1 (TMG server) VLAN:1 ~ 3 IP: 10.0.0.11 ~ 20 (Hosts group 1) VLAN:1 IP: 10.0.0.21 ~ 30 (Hosts group 2) VLAN:2 IP: 10.0.0.31 ~ 40 (Hosts group 3) VLAN:3 Note that I don't want them to connect to each other, so ARP/inter-vlan routing (within the subnet) is not required. The gateway is running in a VM within ESXi 5, I can pass the VLans to the VM using VGT or VLan Range, but I don't know how the OS/TMG should handle them.

  Read the article

• Utilize two gateways on the same network same interface with load balancing

  - by RushPL

  My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

  Read the article

• How to I alias a hostname?

  - by Jonas Byström

  Is it possible to keep a network alias - without specifying the IP address in the hosts file? For instance, I have abcd.efgh.com but want abcd -> abcd.efgh.com so that ping and ssh work as they normally would. I want it to work with dynamic IP on abcd.efgh.com, that's why I don't want to state the IP address explicitly.

  Read the article

• What is automatic service location on the network?

  - by Roman

  I know that zeroconf does automatic service location on the local network. But what does it mean? For example there is a printer (printing is the service that it does). This printer choose randomly an IP for itself. It asks other devices if this IP is already occupied. If not, the printer occupies this IP. Then printer says to "everybody" that "printing" service is associated with this IP. Is it "automatic service location"? Or I got something wrong?

  Read the article

• How to place additional access-restrictions on a subdirectory in Apache?

  - by Mikhail T.

  We have a list of "internal" IP-addresses and only allow access to the server (Location /) from that list: <Location /> Require ip x.x.x.x Require ip y.y.y.y </Location> I need to further restrict access to a sub-directory (Location /foo) to authenticated users (Require valid-user). Whatever I do, I never get prompted for login to access /foo -- Apache simply grants me access, because my IP-address is on the list (for Location /). I cycled through all three different values of AuthMerging (off, and, or) to no avail... Must be something really stupid :-/ Using httpd-2.4.6. Thank you!

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• How do I run both Tomcat and PHP on Linux on port 80?

  - by Michael Gaylord

  I would like to host both Tomcat and PHP on port 80 on Linux and I have 2 IP addresses available. I am only using PHP so that I can host some mailing list software, I can map it to newsletter.mydomain.com. So my question is, is it possible to run Tomcat on port 80 on 1 IP address and Apache on port 80 on another IP address?

  Read the article

• Issue Connecting two home networks

  - by Alex

  Hi, I have a home networking question. I have two DLINK wireless/wired routers in my house, connected to the Internet ISP. There are a 2 computers on each of the two networks. Network1: has 192.168.0.0 (gateway) Valid IP'S range - 192.168.0.1 - 192.168.0.10, with COMP1 having a fixed IP of 162.168.0.1 Network2: has 192.168.0.100 (gateway) Valid IP'S range - 192.168.0.101 - 192.168.0.110 with COMP2 having a static IP of 162.168.0.101, a WIRELESS printer on 192.168.0.102 Both routers have a netmask of 255.255.255.0 My need is to connect the two routers, so that I can Remote desktop for COMP1 to COMP2 and viceversa, and COMP1 to connect to the wireless printer on Network2. can anyone help to set this up so that the both networks can talk to each other. Any help is appreciated. -Alex

  Read the article

• how're routing tables populated?

  - by Robbie Mckennie

  i've been reading "tcp/ip illustrated" and i started reading about ip forwarding. all about how you can receive a datagram and work out where to send it next based on the desination ip and your routing table. but what confused me is how (in a home network setting) the table itself is populated. is there a lower layer protocol at work here? does it come along with dhcp? or is it simply based on the ip address and netmask of each interface? i do know (from other books) that in the early days of ethernet one had to set up routing tables by hand, but i know i didn't do that.

  Read the article

• Connect to remote MySQL using proxy

  - by hypeflow

  I'm trying to connect to a remote MySQL server (with TCP access limited to a specific IP) using port forwarding via SSH, but still haven't figured out how to do it. Here's what I intend to do: Local[A] ---> Proxy[B] ---> Remote MySQL[C] [A] Local machine with Windows [B] CentOS machine with IP 123.123.123.1 (with it's own MySQL running, btw) [C] Remote MySQL server with IP 123.123.123.1 authorized on port 3306 How to achieve this? Thanks in advance.

  Read the article

• SSH: Configure ssh_config to use specific key file for a specific server fingerprint

  - by Penthi

  I have a key based login for a server. The IP and DNS of the server can change, because it is hosted on Amazon. Is there a way to configure the ssh client config to use the specific key file for this server only, when the fingerprint of the server matches? In other words: Normaly servers are matched by IP or DNS in the ssh client config. I want to do this by fingerprint, becaus IP and DNS can change.

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >