Search Results

Search found 6898 results on 276 pages for 'messages'.

Page 144/276 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Using unsigned drivers in Windows 8

  - by T. Fabre

  I just migrated from Windows 7 x64 to 8, but I can't get my VPN software to run anymore : the SafeNet IKE service (installed by SafeNet SoftRemoteLT GA, used by my VPN provider) cannot start anymore. I found that by default unsigned drivers are disabled on Win8, and that is what is blocking the driver. The System event log tells me that the driver (apparently, C:\WINDOWS\SysWow64\Drivers\IPSECDRV.sys ) was blocked when I try to manually start the service (SafeNet IKE Service). I get the same messages for another driver, crypto.sys found in the same folder. I tried using bcdedit to enable unsigned drivers : bcdedit /set loadoptions DDISABLE_INTEGRITY_CHECKS bcdedit /set testsigning ON After reboot, same error. I tried by booting into Win 8's test mode, same issue. Applying the code signing policy (Enabled, Ignore) does not help either. Running gpresult does show that the policy is applied. Any help welcome.

  Read the article

• Best way to monitor host

  - by Axle

  I have just set up a host which receives messages from 300b to 1500b (wrapped stx etx)and replies with the same. It works fine but some times it receives junk data. Is there anyway to monitor this out of band data just so we can make sure we are not receiving massive amounts of it. Also is it possible to monitor if connections time out - where the host did not reply in time or long connections where it takes the host 20 seconds to reply when it normally takes 5. I am aware of IP monitor but I don't think it covers enough - Is there anything else or any other way? Thanks in advance!

  Read the article

• Why is Thunderbird saying I am working offline when Work Offline is not ticked?

  - by Dizzley

  Thunderbird says "You are currently offline. Do you want to go online to get new messages?" The menu item File-Work Offline is not checked. Is there another "offline" setting? Back story: I moved my Thunderbird profile from another user to my new account today following the instructions here. (it's down as I type). This may be a red herring. I have been sending and receiving happily in the last few hours since - so I remain confused. (Windows 7 Enterprise).

  Read the article

• Exchange 2010 sending old Out of Office message

  - by Tatas

  We are just about done with our migration from Exchange 2003 to 2010. I have a user who has been migrated to the new system that is now out on medical leave. He has gone into OWA and set up his Out of Office notification. The good news is that an Out of Office message is sent, the bad news is that it appears to be sending an old outdated message from back when the user was on Exchange 2003, and not honoring the new message set up in OWA. The user has also tried setting this up in Outlook 2010 as well with the same behavior. I have a feeling that this is related to the old public folders (didn't they contain OOF messages?) still lingering around our Exchange org. Any ideas?

  Read the article

• Tomcat / Railo stop responding with no error output

  - by andrewdixon

  This is going to sound very vague and I'm sure it will be voted down for not giving enough information however I don't really have any to give as you will see. We have an AWS instance running Amazon Linux, Apache, Tomcat and Railo and from time to time the Tomcat/Railo simply stops responding to requests and there are no errors output in the catalina.out file or any of the other log files in the Tomcat logs directory. When I issue the command to restart Tomcat/Railo the restart scripts sits there for a while then says that Tomcat has not responded so it has killed it off and then it starts up again and everything is fine until it happens again, anything from a couple of minutes to a couple of days later. I have done my best to check other logs on the server but have found no messages at all to indicate why Tomcat/Railo has given up and stopped responding. Can anyone suggest any reason why it might be doing this and / or any other log file(s) that we could check to see what is happening. Thanks. Andrew.

  Read the article

• using gmail to send mails from your php?

  - by ajsie

  i've read some threads here in SO that someone managed to use gmail's smtp server to send out messages from php script. so if php sends a mail to [email protected] it looks like this: php tells sendmail (smtp server) to send the message sendmail sends the message to gmail's smtp server gmail's smtp server sends the message to hotmail's smtp server so now i wonder, why should one use gmail's smtp server to send a mail? isn't it better just to send the message from sendmail to hotmail's smtp server? correct me if im wrong, but isnt all that requires for a mail to be sent a communication between TWO smtp servers, the senders and the receivers (in this case, hotmail)? and another question, why can't php just send the message directly to hotmail's smtp server, why does it have to go through a local smtp server? and why do you call it a smtp server when sendmail is just acting like a client to send a message and does not receive anything? would be great if someone could shed a light on this topic!

  Read the article

• Managing service passwords with Puppet

  - by Jeff Ferland

  I'm setting up my Bacula configuration in Puppet. One thing I want to do is ensure that each password field is different. My current thought is to hash the hostname with a secret value that would ensure each file daemon has a unique password and that password can be written to both the director configuration and the file server. I definitely don't want to use one universal password as that would permit anybody who might compromise one machine to get access to any machine through Bacula. Is there another way to do this other than using a hash function to generate the passwords? Clarification: This is NOT about user accounts for services. This is about the authentication tokens (to use another term) in the client / server files. Example snippet: Director { # define myself Name = <%= hostname $>-dir QueryFile = "/etc/bacula/scripts/query.sql" WorkingDirectory = "/var/lib/bacula" PidDirectory = "/var/run/bacula" Maximum Concurrent Jobs = 3 Password = "<%= somePasswordFunction =>" # Console password Messages = Daemon }

  Read the article

• How do I run Munin plugins written in Ruby, using RVM?

  - by hlg

  Hi! I try to run some Munin plugins written in Ruby. I would like to use RVM, so Munin needs to know where to find Ruby. I tried to change the line calling munin-cron in the cron file as follows: */5 * * * * munin bash -c 'source /usr/local/lib/rvm && rvm 1.9.2@munin && /usr/bin/munin-cron' This leads to error messages in munin-node.log, saying /usr/bin/env: ruby: No such file or directory When I change the plugins' shebangs to the actual path of the Ruby executable it works, but the RVM environment should be set so that '/usr/bin/env ruby' works. It does when I execute the plugins as root. Any ideas?

  Read the article

• wifi connection turns off oll the time

  - by er-v

  Hello! I realy need help with one strange problem. I have a wifi network in my appartment with wireless N home router Trendnet tew-652BRP. Everething work fine for three of my laptops, but I have one PC with D-Link DWA-140 adapter. It looses connection 2-3 times in 5 minutes. There is following messages in my system log when it does so: The browser has forced an election on network \Device\NetBT_Tcpip_{9537A5C1-3B43-4C56-B94C-CE69A257C3AD} because a master browser was stopped. The TCP/IP NetBIOS Helper service was successfully sent a stop control. The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)] Comment: None The TCP/IP NetBIOS Helper service entered the stopped state. in order of appearence. How can I stop it? I have the latest driver installed.

  Read the article

• Unable to create a Windows 7 system image of a failing hard drive

  - by Rahul

  The hard disk of my one year old T400 Thinkpad has started failing periodic hardware tests. I get a "Targeted Read Test Failed" error. The "SMART short self test" times out. I am now trying to create a Windows 7 System image of the hard disk but it fails without giving any specific error messages. I tried using Comodo Backup but got an error (code 101117) there as well. I have copied the important files in Dropbox but would like to take a full System backup as I have plenty of software installed on the machine. Does anyone know why this is happening and how I can take a backup of the system image ?

  Read the article

• rsyslog server - Can you split up and organize logs?

  - by Jakobud

  I recently setup one of our servers as an rsyslog server. I now have our firewall setup to log everything to that rsyslog server. But there doesn't seem to be an organization of the logs. All the firewall logs are just being dumped into the /var/log/messages on the rsyslog server. I guess I was maybe expecting them to at least be in a machine specific log file or directory. How can I organize the incoming logging? If I setup 20 servers to all log everything to a central rsyslog server, I really don't want everything being dumped into one big file or a few files. How can I setup rsyslog to tell it where to log what? Like if all the logs for a specific server were in it's own directory/file, etc... Is this possible?

  Read the article

• Force .js files saved in ANSI encoding to show in UTF-8 on IIS 7.5

  - by Xcarpa

  I'm migrating a web system that now works on windows server 2003 IIS 6, to IIS 7.5 on windows 2008 server This system generates javascript files with accented characters in ANSI (Portuguese - Brazil). These javascripts shows for example alert messages. In IIS 6 I have no problem with that, but now using IIS 7.5 if those files are not in UTF-8, the accented characters do not appear correctly. Do we have any way to force these files, even in ANSI, to be processed by IIS 7.5 as UTF-8 ? Thank you ! Cheers Xcarpa

  Read the article

• Likelihood of a hard drive PCB replacement working?

  - by Grant Limberg

  I have a 1.5TB Seagate 7200.11 that died. The platter still spins up initially when attached to a machine, but then the drive clicks and spins down. Then the cycle repeats. I've found a few sites that sell replacement PCBs, however I don't know if the PCB is the issue, or something else. Given the symptoms above, is it at all likely that a PCB replacement would help? If not, I won't waste my money on the PCB replacement. Note: I put the drive in an external ESATA controller and tried hooking it up to a Linux box here at work and got some error messages in the logs. I can post them if anyone thinks it will help in determining whether a PCB swap would fix the problem I'm running into.

  Read the article

• What can impact the throughput rate at tcp or Os level?

  - by Jimm

  I am facing a problem, where running the same application on different servers, yields unexpected performance results. For example, running the application on a particular faster server (faster cpu, more memory), with no load, yields slower performance than running on a less powerful server on the same network. I am suspecting that either OS or TCP is causing the slowness on the faster server. I cannot use IPerf , unless i modify it, because the "performance" in my application is defined as Component A sends a message to Component B. Component B sends an ACK to component A and ONLY then Component A would send the next message. So it is different from what IPerf does, which to my knowledge, simply tries to push as many messages as possible. Is there a tool that can look at OS and TCP configuration and suggest the cause of slowness?

  Read the article

• How to debug old initd script under systemd?

  - by Gene Vincent

  I have an older initd script to start my application. It worked fine under older versions of SuSE, but fails on Open SuSE 12.3. The strange thing is cd /etc/init.d ; ./script start works fine. /etc/init.d/script start shows a redirection to systemctl, but doesn't start my application (and also doesn't show any output from the initd script). I don't see any log entries showing me what goes wrong. The only entry I see is in /var/log/messages saying the application was started. How do I debug this ?

  Read the article

• Sendmail Undeliverable Redirection?

  - by Dizzle

  Good afternoon; I don't know much about sendmail, so this may be fairly easy for those of you more experienced with it. We have an account, "[email protected]", sending reports to various groups. From time to time an undeliverable message will be sent back to "[email protected]". We'd like for those undeliverable messages to be rerouted, or bounced, from "[email protected]" to a group of our choosing. To carve out a scenario for clarity: [email protected] sends a report to [email protected] and [email protected] [email protected] has someone who's mail account no longer exists, triggering an undeliverable message being sent back to [email protected] Rather than having the undeliverable message sit in [email protected]'s Inbox, we'd like for it to be automatically rerouted/bounced to an admin group, [email protected] So I guess a "rule" of sorts. I've come across this solution: Sendmail : ignore local delivery But I don't know enough about sendmail to know if this is what will fit this situation. Any help is greatly appreciated.

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Apache crashing at random intervals. Can not find a reason in log files

  - by Nick Downton

  We are having an issue with a VPS running plesk 9.5 on ubuntu 8.04 At seemingly random intervals Apache will disappear and needs to be started manually. I have checked the apache error log, /var/log/messages, individual virtual host apache error files and cannot find anything that coincides with the time of the failure. dmesg is empty which is a bit odd. We have also had the psa service go down for no apparent reason but apache stay up. I'm at a loss to diagnose this really because all the log files I can find do not point to any issues. Are there any others I can look at? Memory usage sits at about 55% (out of 400mb) and it isn't a particularly high trafficed server. Any pointers as to where else I can find out what is going on would be very much appreciated. Nick

  Read the article

• Why are some UDP packets getting blocked?

  - by Tom

  In our organization, we have two test machines running Windows XP. While attempting to test a roll-my-own UDP message server, I found that both could receive small messages (under 2k) just fine. However, when I test sending large packets to both of these machines, one receives them fine, while the other can't receive them at all. Both machines have SP3 and both have their Windows Firewall shut off, but one still isn't working. Can anyone tell me where to look for anything that might be blocking or limiting the packet size on a Windows Machine? Thanks.

  Read the article

• SAMBA and Linux ACLs -- "Permission denied" on write to share but file written nevertheless

  - by MCH

  I set up a writable share directory "/home/net/share" with acl like this: sudo mkdir -p "/home/net/share" sudo setfacl -m "u:localuser:rwx,u:remoteuser:rwx,g:users:rwx" "/home/net/share" My /etc/samba/smb.conf looks like this: [global] workgroup = w server string = server security = user load printers = no log file = /var/log/samba/%m.log max log size = 50 dns proxy = no printing = bsd printcap name = /dev/null disable spoolss = yes encrypt passwords = true invalid users = nobody root follow symlinks = yes wide links = yes [share] comment = Writable by localuser and remoteuser path = /home/net/share valid users = remoteuser read only = no public = no printable = no Locally, localuser and remoteuser have user accounts and smbpasswds and can both read, create and delete files in /home/net/share. But when I log on from a different machine (like this: sudo mount -t cifs //server/share mountpoint/ -o username=remoteuser ), I get "Permission denied" both when trying to create directories and files, oddly though, it does create files (not directories!) despite these messages! How can I get this working?

  Read the article

• Dummy SMTP server as a service

  - by levidos

  Hello, I have a Windows Server 2008 machine with IIS installed which is hosting a webapp that is sending some notification mails once-in-a-while. What I'd like to do is to monitor the email sent by the application. For this I need a dummy SMTP server which intercepts messages but won't send them further but save them locally on the hard disk.I've already found some of them like Papercut, SMTP4Dev. The problem with these that I have to be logged on the server all the time which is not suitable because the server has only 2+1 TS connections. I like to run a program like these as a windows service and check the mails when I need them. Any suggestion is much appreciated. Best Regards,Levente Rog

  Read the article

• How to watch for count of new lines in tail

  - by fl00r

  I want to do something like this: watch tail -f | wc -l #=> 43 #=> 56 #=> 61 #=> 44 #=> ... It counts new lines of tail each second / Linux, CentOs To be more clear. I have got something like this: tail -f /var/log/my_process/*.log | grep error I am reading some error messages. And now I want to count them. How many ~ errors I have got in a second. So one line in a log is one error in a proccess.

  Read the article

• Internet Explorer 9 won't start

  - by cros

  I have installed Internet Explorer 9. Now when I try to start it the application window flashes up briefly before closing again. What's wrong? I have tried to uninstall IE9, then the problem persisted with IE8. I reinstalled IE9 and the problem is still there. I have tried to use inetcpl.cpl to reset all settings and turn on software rendering, but it didn't help. I can't find any error messages in the Event logs, and the crash doesn't give any kind of error message. My system is Windows 7 Enterprise with SP1.

  Read the article

• Windows 7 XPS Document Writer has stopped working

  - by jamie

  I have successfully used the Windows 7 XPS Document writer for quite a while under windows 7 (64 bit). Now however when i try to print i get prompted twice for the output file name and then get different error messages depending upon the application being used. e.g. Notepad gives a 'The I/O operation has been aborted because of either a thread exit or an application request'. I have disabled and reenabled the XPS facilities of windows features and have similiarly removed and readded the printer. But the end result is the same. I've uninstalled all applications i have installed since the time when i know it worked but this also has not made any difference. Suggestions please!

  Read the article

• Is visiting HTTPS websites on a public hotspot secure?

  - by Calmarius

  It's often said that HTTPS SSL/TLS connections are encrypted and said to be secure because the communication between the server and me is encrypted (also provides server authentication) so if someone sniffs my packets, they will need zillions of years to decrypt if using brute force in theory. Let's assume I'm on a public wifi and there is a malicious user on the same wifi who sniffs every packet. Now let's assume I'm trying to access my gmail account using this wifi. My browser does a SSL/TLS handshake with the server and gets the keys to use for encryption and decryption. If that malicious user sniffed all my incoming and outgoing packets. Can he calculate the same keys and read my encrypted traffic too or even send encrypted messages to the server in my name?

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >