Search Results

Search found 24073 results on 963 pages for 'mount point'.

Page 144/963 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

  • Avoiding DNS timeouts when a dns server fails

    - by Neil Katin
    We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

    Read the article

  • UAC being turned off once a day on Windows 7

    - by Mehper C. Palavuzlar
    I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. Actually, this does not happen if it happened once on a specific day. For example, when I start the machine in the morning, it shows up; but it never shows up in the subsequent restarts within that day. On the next day, the same thing happens again. I never disable UAC, but obviously some rootkit or virus causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I can't fix it. First, I have run a full scan on the computer for any probable virus and malware/rootkit activity, but TrendMicro OfficeScan said that no viruses have been found. I went to an old Restore Point using Windows System Restore, but the problem was not solved. What I have tried so far (which couldn't find the rootkit): TrendMicro OfficeScan Antivirus AVAST Malwarebytes' Anti-malware Ad-Aware Vipre Antivirus GMER TDSSKiller (Kaspersky Labs) HiJackThis RegRuns UnHackMe SuperAntiSpyware Portable Tizer Rootkit Razor (*) Sophos Anti-Rootkit SpyHunter 4 There are no other strange activities on the machine. Everything works fine except this bizarre incident. What could be the name of this annoying rootkit? How can I detect and remove it? EDIT: Below is the log file generated by HijackThis: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 13:07:04, on 17.01.2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Windows\system32\taskhost.exe C:\Windows\system32\Dwm.exe C:\Windows\Explorer.EXE C:\Program Files\CheckPoint\SecuRemote\bin\SR_GUI.Exe C:\Windows\System32\igfxtray.exe C:\Windows\System32\hkcmd.exe C:\Windows\system32\igfxsrvc.exe C:\Windows\System32\igfxpers.exe C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe C:\Program Files\Synaptics\SynTP\SynTPEnh.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QLBCTRL.exe C:\Program Files\Analog Devices\Core\smax4pnp.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\VolCtrl.exe C:\Program Files\LightningFAX\LFclient\lfsndmng.exe C:\Program Files\Common Files\Java\Java Update\jusched.exe C:\Program Files\Microsoft Office Communicator\communicator.exe C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe C:\Program Files\Trend Micro\OfficeScan Client\PccNTMon.exe C:\Program Files\Microsoft LifeCam\LifeExp.exe C:\Program Files\Hewlett-Packard\Shared\HpqToaster.exe C:\Program Files\Windows Sidebar\sidebar.exe C:\Program Files\mimio\mimio Studio\system\aps_tablet\atwtusb.exe C:\Program Files\Microsoft Office\Office12\OUTLOOK.EXE C:\Program Files\Babylon\Babylon-Pro\Babylon.exe C:\Program Files\Mozilla Firefox\firefox.exe C:\Users\userx\Desktop\HijackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = about:blank R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,AutoConfigURL = http://www.yaysat.com.tr/proxy/proxy.pac R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Babylon IE plugin - {9CFACCB6-2F3F-4177-94EA-0D2B72D384C1} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [IgfxTray] C:\Windows\system32\igfxtray.exe O4 - HKLM\..\Run: [HotKeysCmds] C:\Windows\system32\hkcmd.exe O4 - HKLM\..\Run: [Persistence] C:\Windows\system32\igfxpers.exe O4 - HKLM\..\Run: [hpWirelessAssistant] C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe O4 - HKLM\..\Run: [SynTPEnh] C:\Program Files\Synaptics\SynTP\SynTPEnh.exe O4 - HKLM\..\Run: [QlbCtrl.exe] C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QlbCtrl.exe /Start O4 - HKLM\..\Run: [SoundMAXPnP] C:\Program Files\Analog Devices\Core\smax4pnp.exe O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [lfsndmng] C:\Program Files\LightningFAX\LFclient\LFSNDMNG.EXE O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\Run: [Communicator] "C:\Program Files\Microsoft Office Communicator\communicator.exe" /fromrunkey O4 - HKLM\..\Run: [AgentUiRunKey] "C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe" -ni -sss -e http://localhost:16386/ O4 - HKLM\..\Run: [OfficeScanNT Monitor] "C:\Program Files\Trend Micro\OfficeScan Client\pccntmon.exe" -HideWindow O4 - HKLM\..\Run: [Babylon Client] C:\Program Files\Babylon\Babylon-Pro\Babylon.exe -AutoStart O4 - HKLM\..\Run: [LifeCam] "C:\Program Files\Microsoft LifeCam\LifeExp.exe" O4 - HKCU\..\Run: [Sidebar] C:\Program Files\Windows Sidebar\sidebar.exe /autoRun O4 - Global Startup: mimio Studio.lnk = C:\Program Files\mimio\mimio Studio\mimiosys.exe O8 - Extra context menu item: Microsoft Excel'e &Ver - res://C:\PROGRA~1\MICROS~1\Office12\EXCEL.EXE/3000 O8 - Extra context menu item: Translate this web page with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/ActionTU.htm O8 - Extra context menu item: Translate with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/Action.htm O9 - Extra button: Research - {92780B25-18CC-41C8-B9BE-3C9C571A8263} - C:\PROGRA~1\MICROS~1\Office12\REFIEBAR.DLL O9 - Extra button: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O9 - Extra 'Tools' menuitem: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O16 - DPF: {00134F72-5284-44F7-95A8-52A619F70751} (ObjWinNTCheck Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/WinNTChk.cab O16 - DPF: {08D75BC1-D2B5-11D1-88FC-0080C859833B} (OfficeScan Corp Edition Web-Deployment SetupCtrl Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/setup.cab O17 - HKLM\System\CCS\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\Software\..\Telephony: DomainName = yaysat.com O17 - HKLM\System\CS1\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\System\CS2\Services\Tcpip\Parameters: Domain = yaysat.com O18 - Protocol: qcom - {B8DBD265-42C3-43E6-B439-E968C71984C6} - C:\Program Files\Common Files\Quest Shared\CodeXpert\qcom.dll O22 - SharedTaskScheduler: FencesShellExt - {1984DD45-52CF-49cd-AB77-18F378FEA264} - C:\Program Files\Stardock\Fences\FencesMenu.dll O23 - Service: Andrea ADI Filters Service (AEADIFilters) - Andrea Electronics Corporation - C:\Windows\system32\AEADISRV.EXE O23 - Service: AgentService - Iron Mountain Incorporated - C:\Program Files\Iron Mountain\Connected BackupPC\AgentService.exe O23 - Service: Agere Modem Call Progress Audio (AgereModemAudio) - LSI Corporation - C:\Program Files\LSI SoftModem\agrsmsvc.exe O23 - Service: BMFMySQL - Unknown owner - C:\Program Files\Quest Software\Benchmark Factory for Databases\Repository\MySQL\bin\mysqld-max-nt.exe O23 - Service: Com4QLBEx - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\Com4QLBEx.exe O23 - Service: hpqwmiex - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\Shared\hpqwmiex.exe O23 - Service: OfficeScanNT RealTime Scan (ntrtscan) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\ntrtscan.exe O23 - Service: SMS Task Sequence Agent (smstsmgr) - Unknown owner - C:\Windows\system32\CCM\TSManager.exe O23 - Service: Check Point VPN-1 Securemote service (SR_Service) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Service.exe O23 - Service: Check Point VPN-1 Securemote watchdog (SR_Watchdog) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Watchdog.exe O23 - Service: Trend Micro Unauthorized Change Prevention Service (TMBMServer) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\..\BM\TMBMSRV.exe O23 - Service: OfficeScan NT Listener (tmlisten) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\tmlisten.exe O23 - Service: OfficeScan NT Proxy Service (TmProxy) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\TmProxy.exe O23 - Service: VNC Server Version 4 (WinVNC4) - RealVNC Ltd. - C:\Program Files\RealVNC\VNC4\WinVNC4.exe -- End of file - 8204 bytes As suggested in this very similar question, I have run full scans (+boot time scans) with RegRun and UnHackMe, but they also did not find anything. I have carefully examined all entries in the Event Viewer, but there's nothing wrong. Now I know that there is a hidden trojan (rootkit) on my machine which seems to disguise itself quite successfully. Note that I don't have the chance to remove the HDD, or reinstall the OS as this is a work machine subjected to certain IT policies on a company domain. Despite all my attempts, the problem still remains. I strictly need a to-the-point method or a pukka rootkit remover to remove whatever it is. I don't want to monkey with the system settings, i.e. disabling auto runs one by one, messing the registry, etc. EDIT 2: I have found an article which is closely related to my trouble: Malware can turn off UAC in Windows 7; “By design” says Microsoft. Special thanks(!) to Microsoft. In the article, a VBScript code is given to disable UAC automatically: '// 1337H4x Written by _____________ '// (12 year old) Set WshShell = WScript.CreateObject("WScript.Shell") '// Toggle Start menu WshShell.SendKeys("^{ESC}") WScript.Sleep(500) '// Search for UAC applet WshShell.SendKeys("change uac") WScript.Sleep(2000) '// Open the applet (assuming second result) WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{ENTER}") WScript.Sleep(2000) '// Set UAC level to lowest (assuming out-of-box Default setting) WshShell.SendKeys("{TAB}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") '// Save our changes WshShell.SendKeys("{TAB}") WshShell.SendKeys("{ENTER}") '// TODO: Add code to handle installation of rebound '// process to continue exploitation, i.e. place something '// evil in Startup folder '// Reboot the system '// WshShell.Run "shutdown /r /f" Unfortunately, that doesn't tell me how I can get rid of this malicious code running on my system. EDIT 3: Last night, I left the laptop open because of a running SQL task. When I came in the morning, I saw that UAC was turned off. So, I suspect that the problem is not related to startup. It is happening once a day for sure no matter if the machine is rebooted.

    Read the article

  • Adobe Coldfusion Railo OpenBD Apache Tomcat Multiple Sites

    - by chris hough
    Here's what I am trying to do, unless I am crazy: I am trying to use Tomcat with the multiple workers, so far I got OpenBD working, but having trouble with Railo, and will be tackling Adobe after. each engine deployed as a war separated by different workers I wanted to keep both the sites and engines inside my sites directory I have to remap the symlink for the WEB-INF when I switch engines = have not found a way around this my thought is to have everything separated into modules and I want to be able to execute both cfm and php code in a single site.  Ideally, it would be amazing if there would be a way to not have to remap the symlink as well. thoughts? can this be done? I am trying to mimic how this would be setup on a live server, not using eclipse for example. here is what I am working with so far: my apache workers.properties worker.list=openbd, openbdadmin, railo, railoadmin  worker.openbd.type=ajp13  worker.openbd.host=local.mydev.openbd  worker.openbd.port=8009 worker.openbdadmin.type=ajp13  worker.openbdadmin.host=local.admin.openbd worker.openbdadmin.port=8009   worker.railo.type=ajp13  worker.railo.host=local.mydev.railo  worker.railo.port=8009 worker.railoadmin.type=ajp13  worker.railoadmin.host=local.admin.railo worker.railoadmin.port=8009   my tomcat servers.xml < Host name="local.admin.openbd" appBase="/Users/[myusername]/Websites/coldfusion.engines"  unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false"        < Context path="" docBase="openbd/" reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host        < Host name="local.admin.railo"   appBase="/Users/[my username]/Websites/coldfusion.engines" unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false"        < Context path="" docBase="railo/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host < Host name="local.mydev.openbd"   appBase="/Users/[my username]/Websites/coldfusion.engines" unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false" < Context path="" docBase="/Users/[my username]/Websites/example.mydev/wwwroot/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true"< /Context < /Host < Host name="local.mydev.railo"   appBase="/Users/[my username]/Websites/coldfusion.engines"  unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false" < Context path="" docBase="/Users/[my username]/Websites/example.mydev/wwwroot/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host my apache vhosts ServerName local.admin.openbd DocumentRoot /Users/[my username]/Websites/coldfusion.engines/openBD/ #Mount OpenBD and tell it to only server cfml files JkMount /*.cfm openbdadmin ErrorLog "/Users/[my username]/Websites/apache.logs/local_openbdadmin_error.log" ServerName local.admin.railo DocumentRoot /Users/[my username]/Websites/coldfusion.engines/railo/ #Mount Railo and tell it to only server cfml files JkMount /*.cfm railoadmin ErrorLog "/Users/[my username]/Websites/apache.logs/local_railoadmin_error.log" ServerName local.mydev DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_error.log" ServerName local.mydev.openbd DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot #Mount OpenBD and tell it to only server cfml files JkMount /*.cfm openbd ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_openbd_error.log" ServerName local.mydev.railo DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot JkMount /*.cfm railo ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_railo_error.log" my folder structure I am using websites/apache.logs/ websites/coldfusion.engines/ websites/coldfusion.engines/cfusion/ websites/coldfusion.engines/openBD/ websites/coldfusion.engines/railo/ websites/example.mydev/ websites/example.mydev/wwwroot/ websites/example.mydev/wwwroot/index.cfm   websites/example.mydev/wwwroot/index.htm   websites/example.mydev/wwwroot/index.php   error log output [Thu Aug 27 00:54:50.443 2009] [11279:2686719776] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Thu Aug 27 00:54:51.346 2009] [11280:2686719776] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (openbdadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (openbdadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=1) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (openbdadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (openbdadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=2) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [error] ajp_service::jk_ajp_common.c (2466): (openbdadmin) connecting to tomcat failed. [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] jk_handler::mod_jk.c (2615): Service error=-3 for worker=openbdadmin [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (railoadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (railoadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=1) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (railoadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (railoadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=2) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [error] ajp_service::jk_ajp_common.c (2466): (railoadmin) connecting to tomcat failed. [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] jk_handler::mod_jk.c (2615): Service error=-3 for worker=railoadmin

    Read the article

  • Testing for disk write

    - by Montecristo
    I'm writing an application for storing lots of images (size <5MB) on an ext3 filesystem, this is what I have for now. After some searching here on serverfault I have decided for a structure of directories like this: 000/000/000000001.jpg ... 236/519/236519107.jpg This structure will allow me to save up to 1'000'000'000 images as I'll store a max of 1'000 images in each leaf. I've created it, from a theoretical point of view seems ok to me (though I've no experience on this), but I want to find out what will happen when there will be directories full of files in there. A question about creating this structure: is it better to create it all in one go (takes approx 50 minutes on my pc) or should I create directories as they are needed? From a developer point of view I think the first option is better (no extra waiting time for the user), but from a sysadmin point of view, is this ok? I've thought I could do as if the filesystem is already under the running application, I'll make a script that will save images as fast as it can, monitoring things as follows: how much time does it take for an image to be saved when there is no or little space used? how does this change when the space starts to be used up? how much time does it take for an image to be read from a random leaf? Does this change a lot when there are lots of files? Does launching this command sync; echo 3 | sudo tee /proc/sys/vm/drop_caches has any sense at all? Is this the only thing I have to do to have a clean start if I want to start over again with my tests? Do you have any suggestions or corrections?

    Read the article

  • ADSL Modem/Router sometimes hands out incorrect IP addresses

    - by Peter Keevill
    My setup is as follows:- Main ADSL modem / router (switch) configured as DHCP server with address range 192.168.0.25-60 The office machines are configured with fixed IP ( not in the same address pool of course ) and hard wired to this router. A wireless access point ( Router ) is connected to provide Internet access for guests in a separate area. This router is NOT configured as a DHCP server. Wireless authentication is turned off. IP address lease times are set to 4 hours. Sometimes guests are able to connect to the wireless access point but they are not given a valid IP. They get 169.x.x.x addresses. Rebooting their machines does not resolve the problem. The only way to resolve is to reboot the main ADSL/router which is often frustrating for other users who are successfully connected with valid IP and DG. The problem seems to occur more frequently to Apple/Mac guests although it also sometimes occurs with Win machines. I personally use Ubuntu on my Laptop and thus far, never have had any problem connecting and getting a valid IP address in the guest area. One further point of note which may give a clue is that certain guests ( always Apple/Mac ) get lease times of 90 days. However, this does not 'stack out' the number of available addresses and of course, rebooting the router clears them until the next time they login.

    Read the article

  • Keytool and SSL Apache config

    - by Safari
    I have a question about SSL certificate... I have generate a certificate using this keytool command.. keytool -genkey -alias myalias -keyalg RSA -keysize 2048 and I used this command to export the certificate keytool -export -alias myalias -file certificate.crt So, I have a file .crt Now I would to configure my Apache ssl module. I need to use keytool...At the moment I can't to use Openssl How can I configure the module if I have only this certificate.crt file? I see these sections in my ssl.conf # Server Certificate: # Point SSLCertificateFile at a PEM encoded certificate. If # the certificate is encrypted, then you will be prompted for a # pass phrase. Note that a kill -HUP will prompt again. A new # certificate can be generated using the genkey(1) command. #SSLCertificateFile /etc/pki/tls/certs/localhost.crt # Server Private Key: # If the key is not combined with the certificate, use this # directive to point at the key file. Keep in mind that if # you've both a RSA and a DSA private key you can configure # both in parallel (to also allow the use of DSA ciphers, etc.) #SSLCertificateKeyFile /etc/pki/tls/private/localhost.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/pki/tls/certs/server-chain.crt How can I configure the correct section?

    Read the article

  • Windows 2003 DC to Windows 2008 R2 DC with same name and same IP

    - by TheCleaner
    Environment = Windows 2003 native domain with 8 DCs I've got an old domain controller that is running 2003, CA Enterprise role, DHCP, DNS, a few GPO scripts that point to shares on it, and some other minor functions. All our servers point to it as their primary DNS, and there's lots of references to its IP or name throughout the domain at this point (8+ years later). I really don't feel like manually changing all of this, it would be a pretty massive undertaking. I want to follow this guide: http://msmvps.com/blogs/acefekay/archive/2010/10/09/remove-an-old-dc-and-introduce-a-new-dc-with-the-same-name-and-ip-address.aspx to hopefully end up with basically an "in-place upgrade" so to say. I considered just doing a P2V of the box, but we don't really want to keep it around running 2003 to be honest. I also considered using a CNAME and adding a 2nd IP (the old one) but again, it seemed like it would be cleaner using the attached link. My actual question: Any gotchas or big caution signs when doing what the link suggests? Anyone gone down this road and have advice on how to proceed?

    Read the article

  • Parking domains and avoiding so called "search engine penalities"

    - by senthilkumar-c
    I have purchased two domains from one particular registrar and hosting from GoDaddy. Assume they are domain1.com and domain2.com Assume my hosting IP address is 111.111.111.111 I added both domain1.com and domain2.com in my domain management control panel and gave the same two nameservers for both domains at my registrar's control panel. So, now, both domains should show the same website. When I ping "domain1.com" or "domain2.com" the results say - Pinging domain1.com [111.111.111.111] with 32 bytes of data: Pinging domain2.com [111.111.111.111] with 32 bytes of data: respectively. So, they both point to the same hosting IP. BUT, internally, I have configured IIS to point them to different folders so that different websites are shown. (My hosting plan is expensive and I intend to use the space and bandwidth for many websites). But still, technically, all domains point to same IP address. Is this a bad thing? Is this what is called "domain parking"? I read some search engine forum posts that two domains pointing to the same IP/Website will be penalised by search engines and stuff. I have also read that simply "parking" the domains won't attract penality. I don't know whether what I have done is parking or the so called "wrong" thing. Can someone shed light on what I have done and what I should do? I don't want to be blacklisted by any search engine. P.S. I know this is not a search engine forum, but I am new to website hosting and domains and I am very weak in nearly all technical terms and concepts relating to web hosting and domains. I thought this will be a good place to understand these things.

    Read the article

  • Troubleshooting an overheating CPU

    - by Jeff Fry
    I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

    Read the article

  • Wifi Works with Android and Windows 8 but not Linux and Win 7

    - by eramm
    Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

    Read the article

  • Apache Virtual Host with directory aliases

    - by brechtvhb
    I'm trying to set up a dynamic virtual host in apache with a directory alias pointing to a difirent path for every domain. Here's what I'm trying to achive. Say I have 2 domains: * www.domain1.com * www.domein2.com I want both to point to the same index.php file (C:/cms/index.php). Now the hard part ... I want directories or certain file types to point to a diffirent path for each domain. Example: * www.domain1.com/layout -> C:/store/www.domain1.com/layout * www.domain2.com/layout -> C:/store/www.domain2.com/layout * www.domain1.com/image.png -> C:/store/www.domain1.com/image.png * www.domain2.com/image.png -> C:/store/www.domain2.com/image.png However the admin directory should point to the same path again for all sites * www.domain1.com/admin -> C:/cms/admin * www.domain2.com/admin -> C:/cms/admin Is there a way to achieve this kind of behaviour in apache 2.2 without having to create a virtualhost entry for each new domain?

    Read the article

  • Faster, secure, protocol/code required for long-distance transfer.

    - by Chopper3
    I've ran into a problem and I'm looking for a new secure protocol/client/server that's faster over a 1Gb/s fibre link - let me tell you the story... I have a pair of redundant, diversely-routed, 1Gb/s links over a distance of around 250 miles or so (not dark fibre but a dedicated point to point link, not a mesh). At the 'client' end I have a HP DL380 G5 (2 x dual-core 2.66Ghz Xeon's, 4GB, Windows 2003EE 32-bit), at the 'server' end I have a HP BL460c G6 (2 x quad-core 2.53Ghz Xeons, 48GB, Oracle Linux 5.3 64-bit). I need to transfer around 500 x 2GB files per week from the client to the server machines per week - but the transfer NEEDS to be secure. Using both iPerf or regular FTP I can get ~80MB/s of transfer pretty consistently, which is great. Using WinSCP or Windows SFTP I can't seem to get more that ~3-4MB/s, at this point the server's CPU is 3% busy while CPU0 of the client goes to ~30% utilised. We've tried editing various TCP window sizes with little success. Both ends are connected to quite low-usage Cisco Cat6509's with Sup720's. I can replace the client machine with a newer machine and/or move it to Linux - but this will take time. Clearly these single-threaded secure Windows clients are introducing too much latency doing their encryption. So a few questions/thoughts; Are there any higher performing secure protocols or client software for Windows that I could try? I'm pretty protocol-gnostic so long as it'll work between Windows and Linux. Should I be using hardware to do the encryption, either in the client or the network parts? If so what would you recommend? I'm not convinced that just swapping the server would be that much faster, the CPU was only at 30% but then again that's higher than I'd have expected given the load - moving to Linux at the client end may be a better idea but would be quite disruptive. Am I missing a trick? Thanks in advance.

    Read the article

  • Single Sign On 802.1x Wireless - saying “Connecting to <SSID>”, hangs for 10 seconds, fails with “Unable to connect to <SSID>, Logging on…”.

    - by Phaedrus
    We are implementing WiFi on Windows 7 machines in our corporate environment. Machines should be able to log into the domain by WiFi as the Machine (Pre-Logon), and as the User (Post-Logon). We have everything working correctly except for 2 things: 1) Sometimes the login scripts don't run 2) The user VLAN is sometimes different than the machine vlan, and no DHCP renew occurs after user logon. I am clear that both these problems should be fixable by using the "Single Sign On" Option under the 802.1x Wireless Vista GPO, and setting the wireless to connect immediately before user logon and also by enabling "This network uses different VLAN for authentication with machine and user credentials" If I enable these GPO settings in a lab, the computer does authenticate & gets WIFI before the user logs on, so when the login box is displayed, it says “Windows will try to connect to ”, even though it is already connected (which should be ok?). Enter the user credentials and it goes to a screen saying “Connecting to ”, hangs for 10 seconds, fails with “Unable to connect to , Logging on…”. Desktop fires up and then the user re-authenticates with no problem as himself instead of the machine, but by that point, we defeat the point of the WiFi SSO “before user logon”. Also by that point, no DHCP renew seems to occur, and the user is still stuck with the wrong IP address for the new VLAN. When the “Connecting to ” screen comes up, there’s no indication on the AP or the Radius server that anything whatsoever is happening after credentials are entered until after the domain logon. Also with this policy enabled, sometimes windows hangs on a black screen indefinitely until I disable the Wireless NIC, so something is knackered for sure. What have I missed? Suggestions are much appreciated... /P

    Read the article

  • Computer not finding hard drives on boot -sometimes-

    - by todd.pund
    Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

    Read the article

  • Seagate 3TB hard drive loses format information

    - by Victor Bugarin
    I have a Windows 7x64 Ultimate, 6 GB memory, 1 TB HD. 3TB Barracuda XT HDD. The HDD is installed on a StarTech 4 bays external enclosure I had troubles so I converted to a GPT, created 1 partition and formatted as NTFS. The hard drive I can write and read to and from the hard drive but it will become unreadable at some point while I am copying files or after I have copied files to it. I have copied large Bluray movies and diverse video files, I have also copied 32 GB of pictures, and I have copied about 86 thousand music files in different formats. At some point the partition becomes unreadable and I have to format the partition again (all files lost) and I have to start the whole process again. At some point I have been unable to copy large ISO (Bluray movies) file images. I have partitioned the HDD in 2 partitions P1 - 2TB, P2 - 1TB and I have lost every single file in either partition the same way. I reformat the HDD and it seems fine. I have run seatools to check the hard drive and it reports to be OK. What gives?

    Read the article

  • 2 Computers, same network, different outgoing speeds when uploading to internet?

    - by user117339
    I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

    Read the article

  • Apache Virtual Host with directory aliases

    - by brechtvhb
    Hi, I'm trying to set up a dynamic virtual host in apache with a directory alias pointing to a difirent path for every domain. Here's what I'm trying to achive. Say I have 2 domains: * www.domain1.com * www.domein2.com I want both to point to the same index.php file (C:/cms/index.php). Now the hard part ... I want directories or certain file types to point to a diffirent path for each domain. Example: * www.domain1.com/layout -> C:/store/www.domain1.com/layout * www.domain2.com/layout -> C:/store/www.domain2.com/layout * www.domain1.com/image.png -> C:/store/www.domain1.com/image.png * www.domain2.com/image.png -> C:/store/www.domain2.com/image.png However the admin directory should point to the same path again for all sites * www.domain1.com/admin -> C:/cms/admin * www.domain2.com/admin -> C:/cms/admin Is there a way to achieve this kind of behaviour in apache 2.2 without having to create a virtualhost entry for each new domain?

    Read the article

  • Suggestions for transitioning to new GW/private network

    - by Quinten
    I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

    Read the article

  • Too many connections to Sql Server 2008

    - by Luis Forero
    I have an application in C# Framework 4.0. Like many app this one connects to a data base to get information. In my case this database is SqlServer 2008 Express. The database is in my machine In my data layer I’m using Enterprise Library 5.0 When I publish my app in my local machine (App Pool Classic) Windows Professional IIS 7.5 The application works fine. I’m using this query to check the number of connections my application is creating when I’m testing it. SELECT db_name(dbid) as DatabaseName, count(dbid) as NoOfConnections, loginame as LoginName FROM sys.sysprocesses WHERE dbid > 0 AND db_name(dbid) = 'MyDataBase' GROUP BY dbid, loginame When I start testing the number of connection start growing but at some point the max number of connection is 26. I think that’s ok because the app works When I publish the app to TestMachine1 • XP Mode Virtual Machine (Windows XP Professional) • IIS 5.1 It works fine, the behavior is the same, the number of connections to the database increment to 24 or 26, after that they stay at that point no matter what I do in the application. The problem: When I publish to TestMachine2 (App Pool Classic) • Windows Server 2008 R2 • IIS 7.5 I start to test the application the number of connection to the database start to grow but this time they grow very rapidly and don’t stop growing at 24 or 26, the number of connections grow till the get to be 100 and the application stop working at that point. I have check for any difference on the publications, especially in Windows Professional and Windows Server and they seem with the same parameters and configurations. Any clues why this could be happening? , any suggestions?

    Read the article

  • How can I document and automate a system's configuration?

    - by Diomidis Spinellis
    Having a system's configuration represented by its current state is risky, inefficient, and opaque. At some point you may be left with an unsupported system and no upgrade path. Then configuring a new system compatible with the old is a process or trial and error. Furthermore, if at some point the system is damaged the only option is to go back to the most recent full backup, and try to remember what changes followed from that point. Also, the only way to create a system compatible with the original is through a complete dump/restore. Finally, in such a setup there's no way to know how you solved a particular problem; the only thing you can do is to look at the corresponding configuration files and try to guess what you changed to achieve the desired effect. Currently for each system I maintain, I keep a log file where I record all system administration activity, starting from the installation: installation options, added packages, changes in configuration files, updates, problem fixes etc. In theory this allows me to (manually) replay all changes to arrive at the current state, or to unroll an erroneous change by executing the reverse commands. However, this process is also inefficient, error-prone, and relies on human judgment. Another thing I've tried is to put /etc configuration files under version control with git. This helps me document the changes automatically and also apply them on a clean setup. But it's not without problems: git has to run under sudo, passwords and private keys may be stored in the repository, installed packages can't be meaningfully tracked, and git will have a fit if I try to extend this approach to all the system's directories. I've also thought about performing all changes through shell scripts or makefiles, but I think this process will require a lot of effort and will be fragile. Are there some better methods or tools that I'm missing?

    Read the article

  • Move Files from a Failing PC with an Ubuntu Live CD

    - by Trevor Bekolay
    You’ve loaded the Ubuntu Live CD to salvage files from a failing system, but where do you store the recovered files? We’ll show you how to store them on external drives, drives on the same PC, a Windows home network, and other locations. We’ve shown you how to recover data like a forensics expert, but you can’t store recovered files back on your failed hard drive! There are lots of ways to transfer the files you access from an Ubuntu Live CD to a place that a stable Windows machine can access them. We’ll go through several methods, starting each section from the Ubuntu desktop – if you don’t yet have an Ubuntu Live CD, follow our guide to creating a bootable USB flash drive, and then our instructions for booting into Ubuntu. If your BIOS doesn’t let you boot using a USB flash drive, don’t worry, we’ve got you covered! Use a Healthy Hard Drive If your computer has more than one hard drive, or your hard drive is healthy and you’re in Ubuntu for non-recovery reasons, then accessing your hard drive is easy as pie, even if the hard drive is formatted for Windows. To access a hard drive, it must first be mounted. To mount a healthy hard drive, you just have to select it from the Places menu at the top-left of the screen. You will have to identify your hard drive by its size. Clicking on the appropriate hard drive mounts it, and opens it in a file browser. You can now move files to this hard drive by drag-and-drop or copy-and-paste, both of which are done the same way they’re done in Windows. Once a hard drive, or other external storage device, is mounted, it will show up in the /media directory. To see a list of currently mounted storage devices, navigate to /media by clicking on File System in a File Browser window, and then double-clicking on the media folder. Right now, our media folder contains links to the hard drive, which Ubuntu has assigned a terribly uninformative label, and the PLoP Boot Manager CD that is currently in the CD-ROM drive. Connect a USB Hard Drive or Flash Drive An external USB hard drive gives you the advantage of portability, and is still large enough to store an entire hard disk dump, if need be. Flash drives are also very quick and easy to connect, though they are limited in how much they can store. When you plug a USB hard drive or flash drive in, Ubuntu should automatically detect it and mount it. It may even open it in a File Browser automatically. Since it’s been mounted, you will also see it show up on the desktop, and in the /media folder. Once it’s been mounted, you can access it and store files on it like you would any other folder in Ubuntu. If, for whatever reason, it doesn’t mount automatically, click on Places in the top-left of your screen and select your USB device. If it does not show up in the Places list, then you may need to format your USB drive. To properly remove the USB drive when you’re done moving files, right click on the desktop icon or the folder in /media and select Safely Remove Drive. If you’re not given that option, then Eject or Unmount will effectively do the same thing. Connect to a Windows PC on your Local Network If you have another PC or a laptop connected through the same router (wired or wireless) then you can transfer files over the network relatively quickly. To do this, we will share one or more folders from the machine booted up with the Ubuntu Live CD over the network, letting our Windows PC grab the files contained in that folder. As an example, we’re going to share a folder on the desktop called ToShare. Right-click on the folder you want to share, and click Sharing Options. A Folder Sharing window will pop up. Check the box labeled Share this folder. A window will pop up about the sharing service. Click the Install service button. Some files will be downloaded, and then installed. When they’re done installing, you’ll be appropriately notified. You will be prompted to restart your session. Don’t worry, this won’t actually log you out, so go ahead and press the Restart session button. The Folder Sharing window returns, with Share this folder now checked. Edit the Share name if you’d like, and add checkmarks in the two checkboxes below the text fields. Click Create Share. Nautilus will ask your permission to add some permissions to the folder you want to share. Allow it to Add the permissions automatically. The folder is now shared, as evidenced by the new arrows above the folder’s icon. At this point, you are done with the Ubuntu machine. Head to your Windows PC, and open up Windows Explorer. Click on Network in the list on the left, and you should see a machine called UBUNTU in the right pane. Note: This example is shown in Windows 7; the same steps should work for Windows XP and Vista, but we have not tested them. Double-click on UBUNTU, and you will see the folder you shared earlier! As well as any other folders you’ve shared from Ubuntu. Double click on the folder you want to access, and from there, you can move the files from the machine booted with Ubuntu to your Windows PC. Upload to an Online Service There are many services online that will allow you to upload files, either temporarily or permanently. As long as you aren’t transferring an entire hard drive, these services should allow you to transfer your important files from the Ubuntu environment to any other machine with Internet access. We recommend compressing the files that you want to move, both to save a little bit of bandwidth, and to save time clicking on files, as uploading a single file will be much less work than a ton of little files. To compress one or more files or folders, select them, and then right-click on one of the members of the group. Click Compress…. Give the compressed file a suitable name, and then select a compression format. We’re using .zip because we can open it anywhere, and the compression rate is acceptable. Click Create and the compressed file will show up in the location selected in the Compress window. Dropbox If you have a Dropbox account, then you can easily upload files from the Ubuntu environment to Dropbox. There is no explicit limit on the size of file that can be uploaded to Dropbox, though a free account begins with a total limit of 2 GB of files in total. Access your account through Firefox, which can be opened by clicking on the Firefox logo to the right of the System menu at the top of the screen. Once into your account, press the Upload button on top of the main file list. Because Flash is not installed in the Live CD environment, you will have to switch to the basic uploader. Click Browse…find your compressed file, and then click Upload file. Depending on the size of the file, this could take some time. However, once the file has been uploaded, it should show up on any computer connected through Dropbox in a matter of minutes. Google Docs Google Docs allows the upload of any type of file – making it an ideal place to upload files that we want to access from another computer. While your total allocation of space varies (mine is around 7.5 GB), there is a per-file maximum of 1 GB. Log into Google Docs, and click on the Upload button at the top left of the page. Click Select files to upload and select your compressed file. For safety’s sake, uncheck the checkbox concerning converting files to Google Docs format, and then click Start upload. Go Online – Through FTP If you have access to an FTP server – perhaps through your web hosting company, or you’ve set up an FTP server on a different machine – you can easily access the FTP server in Ubuntu and transfer files. Just make sure you don’t go over your quota if you have one. You will need to know the address of the FTP server, as well as the login information. Click on Places > Connect to Server… Choose the FTP (with login) Service type, and fill in your information. Adding a bookmark is optional, but recommended. You will be asked for your password. You can choose to remember it until you logout, or indefinitely. You can now browse your FTP server just like any other folder. Drop files into the FTP server and you can retrieve them from any computer with an Internet connection and an FTP client. Conclusion While at first the Ubuntu Live CD environment may seem claustrophobic, it has a wealth of options for connecting to peripheral devices, local computers, and machines on the Internet – and this article has only scratched the surface. Whatever the storage medium, Ubuntu’s got an interface for it! Similar Articles Productive Geek Tips Backup Your Windows Live Writer SettingsMove a Window Without Clicking the Titlebar in UbuntuRecover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CDCreate a Bootable Ubuntu USB Flash Drive the Easy WayReset Your Ubuntu Password Easily from the Live CD TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Tech Fanboys Field Guide Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals

    Read the article

  • Cannot log in to the desktop on ubuntu 11.10?

    - by Jichao
    The problem is, I could log in under the terminal, i could ifup eth0, i could do anything I want in the terminal, but if I use ctrl+alt+f7 goto the gnome login screen, after I input the correct password, the system just send me back to same login screen again. I have created a new user, but it didn't work. I have change all the files under ~/ to jichao:jichao(which is my username) with chown -hR jichao:jichao /home/jichao, but it didn't work too. I searched the internet, somebody said I should see the logs under /var/log/gdm, but there is not a /var/log/gdm directory in my box. Here are the tail of files under /var/log/ tail X.org.log [ 3263.348] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so [ 3263.348] (**) Dell Dell USB Keyboard: always reports core events [ 3263.348] (**) Dell Dell USB Keyboard: Device: "/dev/input/event5" [ 3263.348] (--) Dell Dell USB Keyboard: Found keys [ 3263.348] (II) Dell Dell USB Keyboard: Configuring as keyboard [ 3263.348] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input29/event5" [ 3263.348] (II) XINPUT: Adding extended input device "Dell Dell USB Keyboard" (type: KEYBOARD) [ 3263.348] (**) Option "xkb_rules" "evdev" [ 3263.348] (**) Option "xkb_model" "pc105" [ 3263.348] (**) Option "xkb_layout" "us" kern.log Mar 20 09:32:58 jichao-MS-730 kernel: [ 3182.701247] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input27 Mar 20 09:32:58 jichao-MS-730 kernel: [ 3182.701392] generic-usb 0003:413C:2003.0018: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1.4/input0 Mar 20 09:33:02 jichao-MS-730 kernel: [ 3186.642572] usb 2-1.3: new low speed USB device number 17 using ehci_hcd Mar 20 09:33:02 jichao-MS-730 kernel: [ 3186.741892] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input28 Mar 20 09:33:02 jichao-MS-730 kernel: [ 3186.742080] generic-usb 0003:045E:0047.0019: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-1.3/input0 Mar 20 09:33:27 jichao-MS-730 kernel: [ 3212.473901] usb 2-1.3: USB disconnect, device number 17 Mar 20 09:33:28 jichao-MS-730 kernel: [ 3212.702031] usb 2-1.4: USB disconnect, device number 16 Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.022655] usb 2-1.4: new low speed USB device number 18 using ehci_hcd Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.124278] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input29 Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.124423] generic-usb 0003:413C:2003.001A: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1.4/input0 Mar 20 09:33:02 jichao-MS-730 kernel: [ 3186.741892] input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.3/2-1.3:1.0/input/input28 Mar 20 09:33:02 jichao-MS-730 kernel: [ 3186.742080] generic-usb 0003:045E:0047.0019: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-1.3/input0 syslog Mar 20 09:33:02 jichao-MS-730 mtp-probe: bus: 2, device: 17 was not an MTP device Mar 20 09:33:27 jichao-MS-730 kernel: [ 3212.473901] usb 2-1.3: USB disconnect, device number 17 Mar 20 09:33:28 jichao-MS-730 kernel: [ 3212.702031] usb 2-1.4: USB disconnect, device number 16 Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.022655] usb 2-1.4: new low speed USB device number 18 using ehci_hcd Mar 20 09:34:08 jichao-MS-730 mtp-probe: checking bus 2, device 18: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4" Mar 20 09:34:08 jichao-MS-730 mtp-probe: bus: 2, device: 18 was not an MTP device Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.124278] input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input29 Mar 20 09:34:08 jichao-MS-730 kernel: [ 3253.124423] generic-usb 0003:413C:2003.001A: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.0-1.4/input0 auth.log Mar 20 09:18:52 jichao-MS-730 lightdm: pam_ck_connector(lightdm-autologin:session): nox11 mode, ignoring PAM_TTY :0 Mar 20 09:18:53 jichao-MS-730 lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "jichao" Mar 20 09:18:53 jichao-MS-730 dbus[835]: [system] Rejected send message, 2 matched rules; type="method_call", sender=":1.240" (uid=104 pid=6457 comm="/usr/lib/indicator-datetime/indicator-datetime-ser") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.11" (uid=0 pid=1156 comm="/usr/sbin/console-kit-daemon --no-daemon ") Mar 20 09:19:38 jichao-MS-730 sudo: jichao : TTY=tty6 ; PWD=/home ; USER=root ; COMMAND=/bin/chown -hR jichao:jichao jicha Mar 20 09:19:39 jichao-MS-730 sudo: jichao : TTY=tty6 ; PWD=/home ; USER=root ; COMMAND=/bin/chown -hR jichao:jichao jichao Mar 20 09:20:10 jichao-MS-730 lightdm: pam_unix(lightdm-autologin:session): session closed for user lightdm Mar 20 09:20:11 jichao-MS-730 lightdm: pam_unix(lightdm-autologin:session): session opened for user lightdm by (uid=0) Mar 20 09:20:11 jichao-MS-730 lightdm: pam_ck_connector(lightdm-autologin:session): nox11 mode, ignoring PAM_TTY :0 Mar 20 09:20:12 jichao-MS-730 lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "jichao" Mar 20 09:20:12 jichao-MS-730 dbus[835]: [system] Rejected send message, 2 matched rules; type="method_call", sender=":1.247" (uid=104 pid=6572 comm="/usr/lib/indicator-datetime/indicator-datetime-ser") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.11" (uid=0 pid=1156 comm="/usr/sbin/console-kit-daemon --no-daemon ") It seems that my .xsession-errors does not grow since yesterday. Here is my .xsession-error: (gnome-settings-daemon:1550): Gdk-WARNING **: The program 'gnome-settings-daemon' received an X Window System error. This probably reflects a bug in the program. The error was 'BadWindow (invalid Window parameter)'. (Details: serial 26702 error_code 3 request_code 2 minor_code 0) (Note to programmers: normally, X errors are reported asynchronously; that is, you will receive the error a while after causing it. To debug your program, run it with the --sync command line option to change this behavior. You can then get a meaningful backtrace from your debugger if you break on the gdk_x_error() function.) (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed (nautilus:3106): GLib-GObject-CRITICAL **: g_value_get_object: assertion `G_VALUE_HOLDS_OBJECT (value)' failed WARN 2012-03-17 19:28:46 glib <unknown>:0 Unable to fetch children: Method "Children" with signature "" on interface "org.ayatana.bamf.view" doesn't exist WARN 2012-03-17 19:28:46 glib <unknown>:0 Unable to fetch children: Method "Children" with signature "" on interface "org.ayatana.bamf.view" doesn't exist (yunio:2430): Gtk-WARNING **: ??????????????:“pixmap”, (yunio:2430): Gtk-WARNING **: ??????????????:“pixmap”, (polkit-gnome-authentication-agent-1:1601): Gtk-WARNING **: ??????????????:“pixmap”, (yunio:2430): Gtk-WARNING **: ??????????????:“pixmap”, (yunio:2430): Gtk-WARNING **: ??????????????:“pixmap”, (polkit-gnome-authentication-agent-1:1601): Gtk-WARNING **: ??????????????:“pixmap”, (polkit-gnome-authentication-agent-1:1601): Gtk-WARNING **: ??????????????:“pixmap”, (polkit-gnome-authentication-agent-1:1601): Gtk-WARNING **: ??????????????:“pixmap”, /usr/share/system-config-printer/applet.py:336: GtkWarning: ??????????????:“pixmap”, self.loop.run () (unity-window-decorator:1652): Gtk-WARNING **: ??????????????:“pixmap”, (unity-window-decorator:1652): Gtk-WARNING **: ??????????????:“pixmap”, (unity-window-decorator:1652): Gtk-WARNING **: ??????????????:“pixmap”, (unity-window-decorator:1652): Gtk-WARNING **: ??????????????:“pixmap”, common-plugin-Message: checking whether we have a device for 4: yes common-plugin-Message: checking whether we have a device for 5: yes common-plugin-Message: checking whether we have a device for 6: yes common-plugin-Message: checking whether we have a device for 7: yes common-plugin-Message: checking whether we have a device for 10: yes common-plugin-Message: checking whether we have a device for 8: yes common-plugin-Message: checking whether we have a device for 9: yes (gnome-settings-daemon:13791): GLib-GObject-CRITICAL **: g_object_unref: assertion `G_IS_OBJECT (object)' failed [1331983727,000,xklavier.c:xkl_engine_start_listen/] The backend does not require manual layout management - but it is provided by the application ** (gnome-fallback-mount-helper:1584): DEBUG: ConsoleKit session is active 0 (gnome-fallback-mount-helper:1584): Gdk-WARNING **: gnome-fallback-mount-helper: Fatal IO error 11 (???????) on X server :0. (gdu-notification-daemon:1708): Gdk-WARNING **: gdu-notification-daemon: Fatal IO error 11 (???????) on X server :0. unity-window-decorator: Fatal IO error 11 (???????) on X server :0.0. (bluetooth-applet:1583): Gdk-WARNING **: bluetooth-applet: Fatal IO error 11 (???????) on X server :0. (nm-applet:1596): Gdk-WARNING **: nm-applet: Fatal IO error 11 (???????) on X server :0. (nautilus:3106): IBUS-WARNING **: _connection_closed_cb: Underlying GIOStream returned 0 bytes on an async read (update-notifier:1821): Gdk-WARNING **: update-notifier: Fatal IO error 11 (???????) on X server :0. applet.py: Fatal IO error 11 (???????) on X server :0. (nautilus:3106): Gdk-WARNING **: nautilus: Fatal IO error 11 (???????) on X server :0. Could you help me, Thanks.

    Read the article

  • How do I detect a file write error in C?

    - by rich
    I have an embedded environment where a user might insert or remove a USB flash drive. I would like to know if the drive has been removed, or if there is some other problem when I try to write to the drive. However, Linux just saves the information in its buffers and returns with no indicated error. The computer I'm using comes with a 2.4.26 kernel and libc 2.3.2. I'm mounting the drive this way: i = mount(MEMORY_DEV_PATH, MEMORY_MNT_PATH, "vfat", MS_SYNCHRONOUS, NULL); That works: 50:/root # mount /dev/scsi/host0/bus0/target0/lun0/part1 on /mem type vfat (rw,sync) 50:/root # Later, I try to copy a file to it: int ifile, ofile; ifile = open("/tmp/tmpmidi.mid", O_RDONLY); if (ifile < 0) { perror("open in"); break; } ofile = open(current_file_name.c_str(), O_WRONLY | O_SYNC); if (ofile < 0) { perror("open out"); break; } #define BUFSZ 256 char buffer[BUFSZ]; while (1) { i = read(ifile, buffer, BUFSZ); if (i < 0) { perror("read"); break; } j = write(ofile, buffer, i); if (j < 0) { perror("write"); break; } if (i != j) { perror("Sizes wrong"); break; } if (i < BUFSZ) { printf("Copy is finished, I hope\n"); close(ifile); close(ofile); break; } } If this snippet of code is executed with a write-protected USB memory, the result is Copy is finished, I hope amid a flurry of error messages from the kernel on the console. I believe the same thing would happen if I simply removed the USB drive (without unmounting it). I have also fiddled with devfs. I figured out how to get it to automatically mount the drive, (with the REGISTER event) but it never seems to trigger the UNREGISTER when I pull out the memory. How can I determine in my program whether I have successfully created a file? Update 4 July: It was a silly oversight of me not to check the result from close(). Unfortunately, the file can be closed without error. So that didn't help. What about fsync()? That sounds like a good idea, but that didn't catch the error either. There might be some interesting information in /sys if I had such a thing. I believe that didn't get added until 2.6.?. The comment(s) about the quality of my flash drive are probably justified. It's one of the earlier ones. In fact, write protect switches seem to be extremely rare these days. I think I have to use the overkill option: Create a file, unmount & remount the drive, and check to see if the file is there. If that doesn't solve my problem, then something is really messed up! Note to myself: Make sure the file you try to create isn't already there! By the way, this does happen to be a C++ program. You can tell by the .c_str() which I had intended to edit out for simplicity.

    Read the article

  • Using Optical Flow in EmguCV

    - by Meko
    HI. I am trying to create simple touch game using EmguCV.Should I use optical flow to determine for interaction between images on screen and with my hand ,if changes of points somewhere on screen more than 100 where the image, it means my hand is over image? But how can I track this new points? I can draw on screen here the previous points and new points but It shows on my head more points then my hand and I can not track my hands movements. void Optical_Flow_Worker(object sender, EventArgs e) { { Input_Capture.SetCaptureProperty(Emgu.CV.CvEnum.CAP_PROP.CV_CAP_PROP_POS_FRAMES, ActualFrameNumber); ActualFrame = Input_Capture.QueryFrame(); ActualGrayFrame = ActualFrame.Convert<Gray, Byte>(); NextFrame = Input_Capture.QueryFrame(); NextGrayFrame = NextFrame.Convert<Gray, Byte>(); ActualFeature = ActualGrayFrame.GoodFeaturesToTrack(500, 0.01d, 0.01, 5); ActualGrayFrame.FindCornerSubPix(ActualFeature, new System.Drawing.Size(10, 10), new System.Drawing.Size(-1, -1), new MCvTermCriteria(20, 0.3d)); OpticalFlow.PyrLK(ActualGrayFrame, NextGrayFrame, ActualFeature[0], new System.Drawing.Size(10, 10), 3, new MCvTermCriteria(20, 0.03d), out NextFeature, out Status, out TrackError); OpticalFlowFrame = new Image<Bgr, Byte>(ActualFrame.Width, ActualFrame.Height); OpticalFlowFrame = NextFrame.Copy(); for (int i = 0; i < ActualFeature[0].Length; i++) DrawFlowVectors(i); ActualFrameNumber++; pictureBox1.Image = ActualFrame.Resize(320, 400).ToBitmap() ; pictureBox3.Image = OpticalFlowFrame.Resize(320, 400).ToBitmap(); } } private void DrawFlowVectors(int i) { System.Drawing.Point p = new Point(); System.Drawing.Point q = new Point(); p.X = (int)ActualFeature[0][i].X; p.Y = (int)ActualFeature[0][i].Y; q.X = (int)NextFeature[i].X; q.Y = (int)NextFeature[i].Y; p.X = (int)(q.X + 6 * Math.Cos(angle + Math.PI / 4)); p.Y = (int)(q.Y + 6 * Math.Sin(angle + Math.PI / 4)); p.X = (int)(q.X + 6 * Math.Cos(angle - Math.PI / 4)); p.Y = (int)(q.Y + 6 * Math.Sin(angle - Math.PI / 4)); OpticalFlowFrame.Draw(new Rectangle(q.X,q.Y,1,1), new Bgr(Color.Red), 1); OpticalFlowFrame.Draw(new Rectangle(p.X, p.Y, 1, 1), new Bgr(Color.Blue), 1); }

    Read the article

  • WPF: Viewbox and TranslatePoint

    - by Samir Sabri
    Hello, I have a Viewbox with a Canvas Child, I have the Stretch property of Viewbox to Fill, I have changed the width and height of the Viewbox, I need to get the location of children in Canvas with respect to Viewbox parent I tried : Point p = viewboxInstance.TranslatePoint(new Point(Canvas.GetLeft(child), Canvas.GetTop(child)), viewboxInstanceParent); it gets wrong coordinates! Is there a solution or work around ? Thanks

    Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >