Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 145/534 | < Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >

  • HTB.init / tc behind NAT

    - by Ben K.
    I have an Ubuntu 10 box that I'm trying to set up as a bandwidth-shaping router. The machine has one WAN interface, eth0 and two LAN interfaces, eth1 and eth2. NAT is configured using MASQUERADE as described at InternetConnectionSharing. I'm mostly concerned with shaping outbound traffic from the LAN interfaces -- in the end, I'd like to end up with a hard 768Kbps limit per-LAN-interface (rather than a limit on eth0 pooled across all interfaces). I installed HTB.init, and riffing on the examples, tried to set this up on eth1 by putting three files into /etc/sysconfig/htb: /etc/sysconfig/htb/eth1 DEFAULT=30 R2Q=100 /etc/sysconfig/htb/eth1-2.root RATE=768Kbps BURST=15k /etc/sysconfig/htb/eth1-2:30.dfl RATE=768Kbps CEIL=788Kbps BURST=15k LEAF=sfq I can /etc/init.d/htb start and /etc/init.d/htb stats and see information that /seems/ to suggest it's working...but when I try pulling a large file via the WAN interface the shaping clearly isn't in effect. Any suggestions? My guess is it has something to do with where the shaping falls in the NAT chain, but I really have no idea where to begin troubleshooting this. ---- Update: Here's my /etc/init.d/htb list output, it seems to make sense -- the default rate for eth1 is 768Kbps? ### eth0: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth0: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b ### eth0: filtering rules filter parent 1: protocol ip pref 100 u32 filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:30 match 00000000/00000000 at 12 match 00000000/00000000 at 16 ### eth1: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth1: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b

    Read the article

  • Cisco router not receiving OSPF updates

    - by WebDevHobo
    Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

    Read the article

  • Why won't dhclient use the static IP I'm telling it to request?

    - by mike
    Here's my /etc/dhcp3/dhclient.conf: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, netbios-name-servers, netbios-scope, interface-mtu; timeout 60; reject 192.168.1.27; alias { interface "eth0"; fixed-address 192.168.1.222; } lease { interface "eth0"; fixed-address 192.168.1.222; option subnet-mask 255.255.255.0; option broadcast-address 255.255.255.255; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; } When I run "dhclient eth0", I get this: There is already a pid file /var/run/dhclient.pid with pid 6511 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:1c:25:97:82:20 Sending on LPF/eth0/00:1c:25:97:82:20 Sending on Socket/fallback DHCPREQUEST of 192.168.1.27 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.27 from 192.168.1.254 bound to 192.168.1.27 -- renewal in 1468 seconds. I used strace to make sure that dhclient really is reading that conf file. Why isn't it paying attention to my "reject 192.168.1.27" and "fixed-address 192.168.1.222" lines?

    Read the article

  • Balancing internal services using a Cisco CSS 11501

    - by Ladadadada
    First, the background to the problem: I have a Cisco CSS11501 that I am using to load balance a few web servers. These web servers have two network interfaces, one internal and one external and we are sending the requests to the internal interface. We have the CSS configured to do NAT because our webservers need to see the client's IP address. Because the TCP packets hit the webservers with a source address on the Internet, the webserver tries to send the packet back to the client over the external interface and not through the load balancer. In order to stop these requests being sent back out to the Internet via the external interface, we added a routing rule on these boxes so that all traffic with a source address on the internet will use the load balancer as the gateway. This part works fine. What I would also like to to is use the CSS as a load balancer for internal services such as our MySQL slaves. When I do this, I run into a similar problem; the TCP connection goes from the web server to the load balancer and then from the load balancer to the MySQL slave but the CSS spoofs a source address of the original webserver. The MySQL slave then tries to send the response directly to the webserver via the internal network and not via the load balancer. The ideal solution would be to tell the CSS not to do source address spoofing on the internal network and only do it for requests originating on the Internet. Is this possible ? Failing that, is there a way of directing the load balanced traffic back through the load balancer while keeping the other traffic (say SSH) purely on the internal network ? Is there another way of using the CSS11501 to load balance internal services ?

    Read the article

  • Internet doesn't work when enable local Lan

    - by rakesh yadav
    We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

    Read the article

  • ntop to analyse bandwidth usage on multiple ASA 5505

    - by dunxd
    I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

    Read the article

  • Permission / owner issue with pushing to git when editing directly from repo?

    - by Susan
    I have a web interface for deploying scripts from our repo at Github to our live server. The web interface just triggers a bash script with some git commands. If I make changes locally, push to repo, then run the bash script to pull from repo to live it works fine. However, if I make changes directly in the repo (via Github's web interface), I'm running into fast-forward / lock issues. These are the steps I'm taking: Make a change on a file at Github repo Run a bash script (as apache) via web from live server that attempts a git push / pull. Get these problems: PUSH To [email protected]:name/name.git ! [rejected] master - master (non-fast-forward) error: failed to push some refs to '[email protected]:name/name.git' To prevent you from losing history, non-fast-forward updates were rejected Merge the remote changes before pushing again. See the 'Note about fast-forwards' section of 'git push --help' for details. PULL From github.com:name/name branch master - FETCH_HEAD error: unable to unlink old 'includes/footer.inc' (Permission denied) Updating 8f6d922..d1eba9d Updating 8f6d922..d1eba9d SSH in as root, attempt a push / pull and it works fine. Ideas on why would this method not work from apache?

    Read the article

  • How to get a higher resolution on Ubuntu 11.04 using an intel chipset

    - by Saif Bechan
    I have a bit slow PC here, so I decided to put Ubuntu 11.04 on it. It use to run Windows Vista on a resolution of 1280x1024, so both my hardware and monitor support it. Now I'm on Ubuntu, but can only run 1024x768, and the screen is not that bright. Its like when you don't have the right drivers on a Windows machine. Now i'm new to linux, so I do not know what do do. I have an onboard Intel chipset i965. Maybe this is some useful information, I read something about it on a forum: lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Can someone please tell me how I can get the screen better? saif@sodium:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9

    Read the article

  • OpenVZ with brdiged interfaces and VLAN

    - by Deimosfr
    Hi, I've got a problem with OpenVZ with brdiged VLAN. Here is my configuration : +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN working on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110 : inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seams working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks like ok, but when I start my VE, here is the message : ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please ? Thanks

    Read the article

  • Debian: What are these files in /sys/devices/pci0000:00/ for?

    - by muhuk
    I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

    Read the article

  • Vyatta internet connection + hosted site on same IP

    - by boburob
    Having a small issue setting up a vyatta. The company internet and two different websites are both on the same IP. Server 1 - Has websites hosted on ports 1000 and 3000 and also has a proxy server installed to provide internet connection to the domain Server 2 - Has a website hosted on ports 80 and 433 The vyatta is correctly natting the appropriate traffic to each server, and allowing the proxy to get internet traffic, however I have a problem getting to the websites hosted on these two servers inside the domain. I believe the problem is that the HTTP request is being sent with an IP, eg: 12.34.56.78. The request will reach the website and the server will attempt to send the request back to the IP, however this is the IP of the Vyatta, so it has nowhere else to go. I thought the solution would be something like this: rule 50 { destination { address 12.34.56.78 port 1000 } inbound-interface eth1 inside-address { address 10.19.2.3 } protocol tcp type destination } But this doesnt seem to do it! UPDATE I changed the rules to the following: rule 50 { destination { address 12.34.56.78 port 443 } outbound-interface eth1 protocol tcp source { address 10.19.2.3 } type masquerade } rule 51 { destination { address 12.34.56.78 port 443 } inbound-interface eth1 inside-address { address 10.19.2.2 } protocol tcp type destination } I am now seeing traffic going between the two with Wireshark, but the website will still fail to load.

    Read the article

  • Forward mDns from one subnet to another?

    - by user37278
    Is there an ipfw rule that can easily forward mDns packets from one subnet to another? I have a Snow Leopard Server machine serving as the gateway between the two subnets and would like for machines in each subnet to see the services available in the other subnet. The gateway machine is already confirmed as configured correctly such that packets route correctly between the two subnets (ping works, traceroute shows the subnet hop, etc). My problem in designing a ipfw rule is that I don't know how to instruct that I would like multicast packets addressed to 224.0.0.251:5353 on en0 to be addressed to the same ip/port but on fw0 (the other interface). I attempted a rule such as fwd 192.168.10.1 log udp from 192.168.1.0/24 to 224.0.0.251 recv en1 to force the packet to hop over to the other interface (from en1 to fw0), but no dice. The ipfw log shows that the rule is being triggered by packets, but tcpdump isn't showing any packets on the other interface. Also, the only other firewall rules in place are the divert port 8668 and rule #65535 "allow any to any". Any suggestions? Thanks.

    Read the article

  • OpenVZ with bridged interfaces and VLAN

    - by Deimosfr
    Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

    Read the article

  • Can't Configure IBM 8275-416 Switch Via Serial

    - by Sean M
    I am attempting to configure an IBM 8275-416 switch (I found a manual here) via serial connection. However, when I connect with HyperTerminal, the output contains a lot of garbage characters. It's pretty much unusable, because there's enough layout-breaking text-gunk that it's very difficult to determine what's actually being displayed. . I was able to reset the switch to factory defaults via the terminal interface, so I know that it's not entirely broken. It also performs basic functions all right (i.e., you plug in clients and Ethernet cables - they can connect to clients plugged into other ports) - but I'd like it to do more than that (VLANs yay). I don't know if its in-band UI is operational or not, because I can't get the terminal interface to behave well enough to properly turn on the web/SNMP UI. So that's not available. Things I've tried: - Changing the encoding: HyperTerminal lets me choose between Standard JIS and Shift-JIS. Neither setting fixes the issue. - Checking emulation settings: The manual demands VT100, 19200 baud, 8 data bits, and such: I have faithfully applied these settings, both in HyperTerminal's settings and in the properties of the COM1 port in Device Manager (connecting from a Windows machine). - Restoring to factory defaults: See above. Things that it could be, but that seem unlikely: - Cabling: Couldn't find a proper null-modem cable, so used two 232-to-RJ45 adapters. But if it was a problem with the cable, wouldn't it be more likely to not connect or do input at all, rather than just garble the text? Since I was actually able to perform the reset-to-factory defaults operation, I don't think it's this. - Device as a whole broken: It is a decade and change old, so it's possible that it's just dying slowly. Again, though, it seems like there would be more symptoms than just garbled text in the terminal. What else can I try to get a sane interface to this switch?

    Read the article

  • virtualbox instances dedicated-server with custom dnsmasq

    - by ovanes
    I have dedicated server where I planned to run virtualbox virtual machines. Since the VMs are managed with vagrant/chef I may end up with many different ones. I thought it would be a great idea to deploy a dnsmasq on the server, which is going to dynamically assign the ip addresses to the VMs. Since each Vagrant/Chef recipe is configured to set the VM's host name I can find/reference the appropriate VM by the host name. Finally, the entire infrastructure is not directly accessible via internet, so the dedicated Server is the OpenVPN host. So the entire infrastructure may be seen as: +-------------------------------------+ | Dedicated Server | | | | +-------------+ +------------+ | +------------------+ | | DNSMasq | | OpenVPN |<==========>| Client | | +-------------+ +------------+ | | | | ^ ^ | +------------------+ | | | | | +--+ | | | | +-------+ | | | | VM1 | | | | +-------+ | | | ... | | | +-------+ | | +-| VM2 | | | +-------+ | +-------------------------------------+ Now some questions which I am struggling with: Are there any other suggestions to access private infrastructure, because I don't want to reinvent the wheel. On the Dedicated Server I don't see the vboxnet0 interface but VirtualBox is installed without GUI. Accessing of virtual boxes via ssh works fine. Did I miss smth? DNSMasq must serve the local VMs only, otherwise there is a chance that local DNSMasq start to serve other server's on the network, what I don't want. Because I don't see vboxnet0 I tend to use no-dhcp-interface=eth0 config option. Are there any thoughts on that despite, the fact that a second NW-card (which is not the case), might start serving DHCP-Requests? How should I config the VM's network interface that I am able to access it via OpenVPN and resolve the hostnames using the DNSMasq. I think it should be the host-only network card. Should I do bridging in the OpenVPN config or is it sufficient to use routing.

    Read the article

  • MS Dynamics CRM users disappear

    - by Max Kosyakov
    Recently we came across quite a weird issue. The administrators say that once in a while they notice that user accounts in MS Dynamics CRM are lost . When a new user is added to the system, the administrators add him/her to the Active Directory first. Then, they go to Dynamics CRM interface, then to system configuration -> administration -> users and add the new user to the CRM, add roles to this user, grant them relevant permissions. Then the user is able to use a custom application, which connects to the Dynamics CRM via WCF. After a while (few weeks or months) the user is unable to use the custom application because Dynamics CRM cannot authorise this user. When administrators open the Dynamics CRM user management interface (configuration -> administration -> users ) and browse through the list of CRM users they cannot find the user in the list. When they try to add the user to Dynamics CRM back, the CRM fails with the error message "User already exists". Moreover, the user still exists in the Active Directory. The admins are very sure the user had been added to the CRM before he/she started to work. The only fact the the user was able to use the custom application normally says that the user had been indeed registered in the CRM. How come the user is not listed in the CRM user management interface at all? Have anyone faced any issues like that? Seen or heard of disappearing CRM users somewhere? Any help is appreciated. Where can one start digging?

    Read the article

  • Are there compact external USB audio interfaces which are better than a on-board sound?

    - by rumtscho
    I am asking this for a friend. He loves his voice recognition software and dictates a lot of text using a headset. Now he has a new laptop, which only has a combined mic/headphones output, and wanted to buy an adapter. I told him to get an external USB sound interface instead, as the better sound quality will probably increase the hit rate of the voice recognition. He agreed, but when he saw a picture of the SoundBlaster X-Fi, he said that it is way too big, because he wants to carry the thing everywhere. He'd rather have one of these small things which are the size of a flash memory stick, with only one mic and one phones output, period. Now I am not sure whether these mini interfaces would produce a sound better than onboard sound. They all seem to come not from established audio interface manufacturers, but from electronic accessories manufacturers like Speedlink, or just noname brands. Is there a compact audio interface with good A/D quality (it is OK if the price is comparable to that of the bigger interfaces, even if there is no additional functionality like Chinch in-/output etc)?. And if there isn't, will the noname soundcardsticks offer any advantage over a simple adaptor for the onboard sound?

    Read the article

  • Are SATA II and SATA 3.0 Gbps compatible?

    - by Johnny Maelstrom
    I am trying to check that if I buy a new internal HDD it will work in the NAS I am buying. Currently I'm confused about naming schemes and once that is resolved whether there is compatibility. I will gladly author this question to be more general if there is not already an article helping with the confusion of SATA naming and standards. I see similar, but not identical questions and will accept this as a duplicate if thought as such. The specifications on the eCommerce site for the NAS says, "Controller Interface Type Serial ATA-150", the product home page for the manufacturer says, "Compatible with SATA and SATA II HDD". The specifications on the eCommerce site for the hard drives say, "Interface Type Serial ATA-300", the product home page for the manufacturer says, "Interface SATA 3.0 Gbps" Wikipedia says many things about different naming conventions, the closest being, "SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them." Are SATA II and SATA 3.0 Gbps the same? I feel I'm tantalisingly close to getting a definitive answer here before I purchase, but really want to clear up these naming schemes.

    Read the article

  • nginx redirect proxy

    - by andrew
    I have a web app running on a nginx server on local ip 192.168.0.30:80 I have this in my etc/hosts 127.0.0.1 w.myapp.in If someone accesses my app using a "w" subdomain, it shows a webdav interface, otherwise it runs normally (for example, someone calls http://myapp.in , it goes into the app, and http://w.myapp.in goes into webdav interface - this is done within the app, nginx has nothing to do with it) Because I don't have a dns or anything like that, users must access the app by ip. A problem appears if someone wants to access the webdav interface, because you cannot access the app by a subdomain - unless you write a line in your local hosts file, which is not a solution) A possible solution If it's possible to setup the nginx server so that if someone calls http://192.168.0.30 (on port 80), it goes normally into the app, but if a user tries to access say http://192.168.0.30:81 (another defined port) it redirects internally to w.myapp.in, and the app sees the subdomain Given the app, can this be done? If yes, what should I put in the nginx config file? And if you guys think of a better solution, I'm open to any.

    Read the article

  • PCs on domain can not resolve external IP addresses using the DC's DNS Server

    - by Ben
    I currently have a domain controller which handles all DHCP and DNS. The DHCP works just fine and the domain controller itself can use the internet with no issues. However, PCs that are part of the domain are not able to use external websites, only internal. Does anyone have any way I can solve this issue? Thank you Server: Windows Server 2008 R2 PC: Win7 Enterprise x64 Edit: (domain controller) C:\Users\bcollyer>nslookup google.com Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: google.com Addresses: 2a00:1450:4009:809::100e 173.194.41.166 173.194.41.165 173.194.41.169 173.194.41.162 173.194.41.161 173.194.41.160 173.194.41.168 173.194.41.167 173.194.41.164 173.194.41.163 173.194.41.174 Edit 2: C:\Users\bcollyernetstat -rn Interface List 12...30 85 a9 f7 8a 21 ......Atheros AR8161/8165 PCI-E Gigabit Ethernet Control ler (NDIS 6.20) 1...........................Software Loopback Interface 1 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11...00 00 00 00 00 00 00 e0 Microsoft Teredo Tunneling Adapter IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.0.67 172.16.0.202 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.0.0 255.255.0.0 On-link 172.16.0.202 276 172.16.0.202 255.255.255.255 On-link 172.16.0.202 276 172.16.255.255 255.255.255.255 On-link 172.16.0.202 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.0.202 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.0.202 276 Persistent Routes: None IPv6 Route Table Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link Persistent Routes: None BTW I have no javascript on the server so can't reply to individual answers... Sorry!

    Read the article

  • Forward all traffic from one IP to another Ip on OS X

    - by Josh
    This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

    Read the article

  • What is the reason for this DNSSEC validation failure of dnsviz.net?

    - by grifferz
    On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

    Read the article

  • VMWare use of Gratuitous ARP REPLY

    - by trs80
    I have an ESXi cluster that hosts several Windows Server VMs and around 30 Windows workstation VMs. Packet captures show a high number of ARP replies of the form: -sender_ip: VM IP -sender_mac: VM virtual MAC -target_ip: 0.0.0.0 -target_mac: Switch interface MAC The specific addresses aren't really a concern -- they're all legitimate and we're not having any problems with communications (most of the questions surrounding GARP and VMWare have to do with ping issues, a problem we don't have). I'm looking for an explanation of the traffic pattern in an environment that functions as expected. So the question is why would I see a high number of unsolicited ARP replies? Is this a mechanism VMWare uses for some purpose? What is it? Is there an alternative? EDIT: Quick diagram: [esxi]--[switch vlan]--[inline IDS]--[fw]--(rest of network) The IDS is complaining about these unsolicited ARPs. Several IDS vendors trigger on ARP replies without a prior request, or for ARP replies that have a target IP of 0.0.0.0. The target MAC in these replies is the VLAN interface on the switch. Capture points: -The IDS grabs the offending packets -The FW can see the same ones -A VM on the ESXi host does not see these, although there is an ARP request for a specific IP on the ESXi host that has source_ip=0.0.0.0 and source_mac=[switch vlan interface]. I can't share the captures, unfortunately. Really I'm interested in finding out if this is normal for an ESXi deployment.

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

  • Watchguard Firebox "split" fibre optic line into 2 interfaces

    - by fRAiLtY-
    We have a requirement on our Watchguard Firebox XTM505 to be able to split our incoming external interface, in this case a fibre optic dedicated leased line, 100/100. We use the line in our office of approx 30 machines however we also re-sell to an external company who utilise it to provide wireless internet solutions to the public. The current infrastructure is as follows: Data in (Leased Line) - Juniper SRX210 managed by ISP - 1 cable out into unmanaged Netgear switch - 1 cable into our firewall and office network, 1 cable to our external providers core router managed by them. We have been informed that having the unmanaged switch in the position it is poses a security risk and that a good option would be to get our Watchguard Firewall to perform the split, by separating our office onto a trusted interface, and by "passing through" the external line to their managed router. It is alleged that the Watchguard is capable of doing this and also rate limiting the interfaces, i.e. 20mbps for the trusted interface and 80mbps for the "pass-through", however Watchguard technical support don't seem to be able to understand what we're trying to achieve. Can anyone provide any advice on whether this is possible on a Watchguard device and how or perhaps if there's a better way of achieving this, perhaps with a managed switch instead of unmanaged? Cheers

    Read the article

< Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >