Search Results

Search found 4268 results on 171 pages for 'srikanth vm'.

Page 145/171 | < Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• How to run Android-x86 project's ISO in VirtualBox with ethernet?

  - by Shiki

  I managed to find a way just days ago, but I had to leave my other PC and now I have no clue how to get it working again. Basically you have to get the image, then install it in a VirtualBox guest. Now the problem is ... when you launch your VM, there is no internet connection. No with NAT or Bridged. Tried all the network cards too. Since internet connection is crucial for Android development, I have to get this thing working. (As I said, I managed to fix it once.) I'm using: - The 4.0 RC1 images from Android-x86 - VirtualBox - Eclipse 4.2 Juno with the latest Android ADT - Android SDK v18 - upgraded to 19 via the Package manager. Now I seen a lot of different builds on the net, about different Android builds for VirtualBox. I have checked Buildroid for example, but there is no network connection. I have imported the virtual machine just as the howto said. The extension package is also installed and it's up to date.

  Read the article

• Ensuring a repeatable directory ordering in linux

  - by Paul Biggar

  I run a hosted continuous integration company, and we run our customers' code on Linux. Each time we run the code, we run it in a separate virtual machine. A frequent problem that arises is that a customer's tests will sometimes fail because of the directory ordering of their code checked out on the VM. Let me go into more detail. On OSX, the HFS+ file system ensures that directories are always traversed in the same order. Programmers who use OSX assume that if it works on their machine, it must work everywhere. But it often doesn't work on Linux, because linux file systems do not offer ordering guarantees when traversing directories. As an example, consider there are 2 files, a.rb, b.rb. a.rb defines MyObject, and b.rb uses MyObject. If a.rb is loaded first, everything will work. If b.rb is loaded first, it will try to access an undefined variable MyObject, and fail. But worse than this, is that it doesn't always just fail. Because the file system ordering on Linux is not ordered, it will be a different order on different machines. This is worse because sometimes the tests pass, and sometimes they fail. This is the worst possible result. So my question is, is there a way to make file system ordering repeatable. Some flag to ext4 perhaps, that says it will always traverse directories in some order? Or maybe a different file system that has this guarantee?

  Read the article

• Dual Monitor support rdp 7 to win 7 on esxi

  - by rphilli5

  I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

  Read the article

• Failed to open the Parallels networking module

  - by user49204

  I'm running Parallels Desktop 7 on OSX Lion and encounter the issue in the subject on every time I'm trying to launch Parallels VM. The error message contains a hint to restore to network configuration default which does not help. As been advised by some forums to ran the following script: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hypervisor.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_hid_hook.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_usb_connect.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_vnic.kext" The output of: sudo kextutil "/Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext" is: Diagnostics for /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext: Warnings: The booter does not recognize symbolic links; confirm these files/directories aren't needed for startup: /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeDirectory /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeRequirements /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeResources /Library/Parallels/Parallels Service.app/Contents/Kexts/10.6/prl_netbridge.kext/Contents/CodeSignature Dependency Resolution Failures: No kexts found for these libraries: com.parallels.kext.prl_hypervisor I've noticed that prl_netbridge is not being loaded (when I'm trying to unload it, I'm notified it is not loaded). Am I doing something wrong? What can be the reason for such behaviour?

  Read the article

• 613 threads limit on debian

  - by Joel

  When running this program thread-limit.c on my dedicated debian server, the output says that my system can't create more than around 600 threads. I need to create more threads, and fix my system misconfiguration. Here are a few informations about my dedicated server: de801:/# uname -a Linux de801.ispfr.net 2.6.18-028stab085.5 #1 SMP Thu Apr 14 15:06:33 MSD 2011 x86_64 GNU/Linux de801:/# java -version java version "1.6.0_26" Java(TM) SE Runtime Environment (build 1.6.0_26-b03) Java HotSpot(TM) 64-Bit Server VM (build 20.1-b02, mixed mode) de801:/# ldd $(which java) linux-vdso.so.1 => (0x00007fffbc3fd000) libpthread.so.0 => /lib/libpthread.so.0 (0x00002af013225000) libjli.so => /usr/lib/jvm/java-6-sun-1.6.0.26/jre/bin/../lib/amd64/jli/libjli.so (0x00002af013441000) libdl.so.2 => /lib/libdl.so.2 (0x00002af01354b000) libc.so.6 => /lib/libc.so.6 (0x00002af013750000) /lib64/ld-linux-x86-64.so.2 (0x00002af013008000) de801:/# cat /proc/sys/kernel/threads-max 1589248 de801:/# ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 794624 max locked memory (kbytes, -l) 32 max memory size (kbytes, -m) unlimited open files (-n) 10240 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 128 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Here is the output of the C program de801:/test# ./thread-limit Creating threads ... Address of c = 1061520 KB Address of c = 1081300 KB Address of c = 1080904 KB Address of c = 1081168 KB Address of c = 1080508 KB Address of c = 1080640 KB Address of c = 1081432 KB Address of c = 1081036 KB Address of c = 1080772 KB 100 threads so far ... 200 threads so far ... 300 threads so far ... 400 threads so far ... 500 threads so far ... 600 threads so far ... Failed with return code 12 creating thread 637. Any ideas how to fix this please ?

  Read the article

• Serving images from another hostname vs Apache overload for the rewrites

  - by luison

  We are trying to improve further the speed of some sites with older HTML in order as well to obtain better SEO results. We have now applied some minify measures, combined html, css etc. We use a small virtualized infrastructure and we've always wanted to use a light + standar http server configuration so the first one can serve images and static contents vs the other one php, rewrites, etc. We can easily do that now with a VM using the same files and conf of vhosts (bind mounts) on apache but with hardly any modules loaded. This means the light httpd will have smaller fingerprint that would allow us to serve more and quicker, have more minSpareServer running, etc. So, as browsers benefit from loading static content from different hostnames as well, we've thought about building a rewrite rule on our main server (main.com) to "redirect" all images and css *.jpg, *.gif, *.css etc to the same at say cdn.main.com thus the browser being able to have more connections. The question is, assuming we have a very complex rewrite ruleset already (we manually manipulate many old URLs for SEO) will it be worth? I mean will the additional load of main's apache to have to redirect main.com/image.jpg (I understand we'll have to do a 301) to cdn.main.com/image.jpg + then cdn.main.com having to serve it, be larger than the gain we would be archiving on the browser? Could the excess of 301s of all images on a page be penalized by google? How do large companies work this out, does the original code already include images linked from the cdn with absolute paths? EDIT Just to clarify, our concern is not to do so much with server performance or bandwith. We could obviously employ an external CDN server but we have plenty CPU and bandwith. Our concern is with how to have "old" sites with plenty semi-static HTML content benefiting from splitting connections for images and static content via apache without having to change the html to absolute paths (ie. image.jpg to cdn.main.com/image.jpg happening on the server not the code)

  Read the article

• Virtual Machines and Automatic Software Updates

  - by Zian Choy

  It's obvious that one's main computer should always be have all the latest security patches and most people don't blink an eye when Microsoft Update installs non-security updates. In the land of virtual machines, I've run into 2 problems with automatic updates: The virtual machines are only run when needed. Only Windows virtual machines seem to patch themselves. To elaborate on #1, I generally make a virtual machine with a purpose in mind. For example, when I needed an old copy of Internet Explorer to reproduce a bug in RSS Bandit, I had a Virtual PC named RSS Bandit. The machine only stayed running for a few minutes at a time. Consequently, there is no downtime for the machine to download updates at 3 AM. To elaborate on #2, I've noticed that if I haven't run a Windows virtual machine in a while, then the moment I log in, the computer frantically downloads updates and within seconds, if I click the Start button, there is a little orange shield next to the "Shutdown" button. However, I ran a freshly created Ubuntu VM for several hours today with hundreds of updates pending and it seemed to never download any of them or install any of them. Is there any reason to be concerned about running VMs with dozens of security holes? If I should be concerned, then is there any way to get Ubuntu to download and install updates rather than just advertising a long list of updates to download next century? I've already tried telling Ubuntu to automatically download and install updates.

  Read the article

• ProCurve network expansion

  - by Blue Warrior NFB

  I've hit a bit of a wall with our network scale-out. As it stands right now: We have five ProCurve 2910al switches connected as above, but with 10GbE connections (two CX4, two fiber). This fully populates the central switch above, there will be no more 10GbE Ethernet connections from that device. This group of switches is not stacked (no stack directive). Sometime in the next two or three months I'll need to add a sixth, and I'm not sure how deep of a hole I'm in. Ideally I'd replace the core switch with something more capable and has more 10GbE ports. However, that's a major outage and that requires special scheduling. The two edge switches connected via fiber have dual-port 10GbE cards in them, so I could physically put another switch on the far end of one of those. I don't know how much of a good or bad idea that would be though. Is that too many segments between end-points? Some config-excerpts: Running configuration: ; J9147A Configuration Editor; Created on release #W.14.49 hostname "REDACTED-SW01" time timezone 120 module 1 type J9147A module 2 type J9008A module 3 type J9149A no stack trunk B1 Trk3 Trunk trunk B2 Trk4 Trunk trunk A1 Trk11 Trunk trunk A2 Trk12 Trunk vlan 15 name "VM-MGMT" untagged Trk2,Trk5,Trk7 ip helper-address 10.1.10.4 ip address 10.1.11.1 255.255.255.0 tagged 37-40,Trk3-Trk4,Trk11-Trk12 jumbo ip proxy-arp exit

  Read the article

• "postgres blocked for more than 120 seconds" - is my db still consistent?

  - by nn4l

  I am using an iscsi volume on an Open-E storage system for several virtual machines running on a XenServer host. Occasionally, when there is a very high disk I/O load on the virtual machines (and therefore also on the storage system), I got this error message on the vm consoles: [2594520.161701] INFO: task kjournald:117 blocked for more than 120 seconds. [2594520.161787] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162194] INFO: task flush-202:0:229 blocked for more than 120 seconds. [2594520.162274] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162801] INFO: task postgres:1567 blocked for more than 120 seconds. [2594520.162882] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. I understand this error message is caused by the kernel to inform that these processes haven't been run for 120 seconds, most likely because a disk access to the storage system has not yet been processed. But what is the effect on the processes. For example, will the postgres process eventually write its data when the storage system is idle again after a few minutes, so that all data is still consistent? Or will it abort the write, leaving some tables in an inconsistent state? I certainly expect that the former should be the case - if the disk access is slow, postgres (or any other affected process) should just wait as long as it takes. I can live with the application hanging for a few minutes. But if there is a chance for data corruption then any of these errors is really bad news. Please advise what to do here.

  Read the article

• How do I switch java versions to an earlier version in Fedora 17?

  - by JHutson456

  I just installed Fedora 17. I'm setting up the Android Build Environment and need Java. I downloaded and installed jdk-6u32-linux-amd64.rpm I ran java -version and it spit out the correct version. Well a day or two later i tried my first compile in Fedora 17 and it complained about java and failed. I ran java -version again and low and behold it spits out $ java -version java version "1.7.0_03-icedtea" OpenJDK Runtime Environment (fedora-2.1.fc17.7-x86_64) OpenJDK 64-Bit Server VM (build 22.0-b10, mixed mode) I'm stumped. I mean, i've run the update/upgrade commands since i installed but i didn't think that updated full version revisions... So, I ran alternatives --config java and that only gave me the java 1.7 version. While digging around more I discovered that the recommended version of Java for the build environment is jdk-6u27-linux-x64-rpm.bin so I downloaded that from here: Oracle Download When I ran: sudo sh jdk-6u27-linux-x64-rpm.bin it returned: Unpacking... Checksumming... Extracting... UnZipSFX 5.50 of 17 February 2002, by Info-ZIP ([email protected]). inflating: jdk-6u27-linux-amd64.rpm inflating: sun-javadb-common-10.6.2-1.1.i386.rpm inflating: sun-javadb-core-10.6.2-1.1.i386.rpm inflating: sun-javadb-client-10.6.2-1.1.i386.rpm inflating: sun-javadb-demo-10.6.2-1.1.i386.rpm inflating: sun-javadb-docs-10.6.2-1.1.i386.rpm inflating: sun-javadb-javadoc-10.6.2-1.1.i386.rpm Preparing... ########################################### [100%] package jdk-2000:1.6.0_32-fcs.x86_64 (which is newer than jdk-2000:1.6.0_27-fcs.x86_64) is already installed Done. so now I'm confused. I ran: alternatives --config java again but it's still only returning 1.7 so I don't know what to do.I want to end up with 6u27 as the installed and functional version of the JDK. Thank you.

  Read the article

• time sync with ntpd

  - by guthrie

  I run Debian on several systems, and their times do not seem to stay in sync. I can run ntpdate manually, but I thought that I should have an ntpd running that would automate that. I did check with apt and apt-cache but don't find any ntpd (or associated ntpq), not any such names in my system (locate...), but ntp-doc does still describe them. Looking around I see that there is an ntpdate-debian command, and it uses /etc/default/ntpdate for servers (instead of the standard /etc/ntp.conf), but even thought that file is there and has "yes" indicated to use ntp.conf, it fails with "no servers can be used", although ntpdate works fine. Is this just a layer over ntpdate, any reason to use it instead? So, why are they missing, do I need them, how do I automate time updates? Associated, two of my machines are virtualized on a MSoft VM, how is it that their clocks drift, and both to different values? (The underlying Windows machine clock seems stable). I see a few old notes about time & ntp problems on VMware, didn't find anything either current or relating to MSoft VMs. Anything I did see says just to use ntpd, but as above, ...?!

  Read the article

• Clustering/load balancing for cluster unaware applications

  - by AaronLS

  Forgive me if I use any of these terms incorrectly. I am wondering if there is any kind of software that would allow my two "join" two computers together such that a cluster unaware application could utilize their combined computing resources? By "cluster unaware" I mean an application that isn't designed to share work across multiple services. My understanding is that clustering is enabled by the specific application by it's architecture, such that messaging with multiple instances of the application coordinate the sharing of work. Instead I am looking for something that enables clustering at the OS or virtualization level, so that any application could essentially be clustered. Failing that, I am also wondering about the following scenario: We have 3 different applications we will call A, B, and C. We have 2 single core computers. At any given time lets say that any combination of those applications will be CPU intensive. In cases where only 2 of those apps are very active, have one of them moved over to a different server. In a nutshell, some sort of dynamic automatic shuffling of the application's load. I have heard of virtual machines that can be migrated across physical machines while live, but I am wondering if this can be done automatically in response to an application's or VM's CPU activity?

  Read the article

• Using mixed disks and OpenFiler to create RAID storage

  - by Cylindric

  I need to improve my home storage to add some resilience. I currently have four disks, as follows: D0: 500Gb (System, Boot) D1: 1Tb D2: 500Gb D3: 250Gb There's a mix of partitions on there, so it's not JBOD, but data is pretty spread out and not redundant. As this is my primary PC and I don't want to give up the entire OS to storage, my plan is to use OpenFiler in a VM to create a virtual SAN. I will also use Windows Software RAID to mirror the OS. Partitions will be created as follows: D0 P1: 100Mb: System-Reserved Boot D0 P2: 50Gb: Virtual Machine VMDKs for OS D0 P3: 350Gb: Data D1 P1: 100Mb: System-Reserved Boot D1 P2: 50Gb: Virtual Machine VMDKs for OS D1 P3: 800Gb: Data D2 P1: 450Gb: Data D3 P1: 200Gb: Data This will result in: Mirrored boot partition Mirrored Operating system Mirrored Virtual machine O/S disks Four partitions for data In the four data partitions I will create several large VMDK files, which I will "mount" into OpenFiler as block-storage devices, combined into three RAID arrays (due to the differing disk sizes) In effect, I'll end up with the following usable partitions SYSTEM 100Mb the small boot partition created by the Windows 7 installer (RAID-1) HOST 50Gb the Windows 7 partition (RAID-1) GUESTS 50Gb Virtual machine Guest VMDK's (RAID-1) VG1 900Gb Volume group consisting of a RAID-5 and two RAID-1 VG2 300Gb Volume group consisting of a single disk On VG1 I can dynamically assign storage for my media, photographs, documents, whatever, and it will be safe. On VG2 I can dynamically assign storage for my data that is not critical, and easily recoverable, as it is not safe. Are there any particular 'gotchas' when implementing a virtual OpenFiler like this? Is the recovery process for a failing disk going to be very problematic? Thanks.

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• Skip all warning prompts on ACPI shutdown?

  - by N Rahl

  When I issue an ACPI shutdown command to a Windows XP guest machine from the host VM server, I want Windows to shutdown. The problem is, Windows always wants to ask some question or another, rather than just shutting down. I need shutdown to be reliable, no matter what is running or going on, so I can automate shutdowns from the host machine. But I want it to be as graceful as possible, rather than just pulling the plug. Some problems: If a user is logged in, ACPI shutdown causes a box to appear that says, "are you sure you want to shutdown while other users are logged in"? And this prevents shutdown until someone connects to the machine and clicks "yes". In this case, it should try its best to gracefully log out all users, using force if necessary, and then shutdown without promoting. Busy or non-responding programs or programs asking to save data can prevent Windows from shutting down until a user answers a prompt. This should attempt to save data, wait maybe 30 seconds for non-responding programs, but should get aggressive with stubborn programs. "nope, time's up! 3,2,1, Goodbye!" Is there a registry setting that I can change from: ACPI_Shutdown: "Shut down if Windows feels like it" to ACPI_Shutdown: "Just do it. Kill programs, bump users, try to be graceful about it, but when I come back, I expect you to be off." This should respond to the ACPI shutdown command, and not be a script on windows, unless that script is triggered by the ACPI power button. I'm hoping this can be changed with registry options.

  Read the article

• Issue resolving names on Hyper-V guest with Routing and Remote Access

  - by John Sheehan

  I've got a Win2k8 standard server running Hyper-V with a Server 2003 web guest instance running. The host is publicly available on the internet. I've created an Internal Private network in the Hyper-V Virtual Network manager. I've set the host IP for that virtual adapter to 192.168.0.1. I've set the IP on the guest to 192.168.0.2. They can ping each other and share files. I can't browse the web on the guest though. NSLOOKUPs are working. I've tried setting the DNS server setting on the guest to 192.168.0.1 and something external like Google's 8.8.8.8 server to no avail. Windows firewall is disabled on the internal virtual network. I've tried it with both DNS installed on the host and without it. I'm not sure which RRAS/NAT settings are relevant to pass on so ask if you need me to clarify anything. How do I get outbound internet working on the guest VM?

  Read the article

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• Internet connection & IIS stopped on windows xp after VMware server 2 installation

  - by Eduardo Xavier

  Hi, I'm running a local network. My IP ranges from 192.168.1.2 to 192.168.1.15. All IP are static ones. And my router's IP is 192.168.1.1 and I provide it as default gateway and preferred DNS server on client machines. Everything worked fine on this scenario. I could use internet and reach services on other machines. BUT I have installed VMware server 2 on the windows XP to host windows 2003 Virtual Machine (VM). I set the following configuration: Windows XP's => 192.168.1.11. Windows 2003 => 192.168.1.12. (virtual machine) This approach worked just fine as it used to work with Microsoft Virtual PC. I can access mysql & IIS websites on the windows 2003 virtual machine. BUT two things doesn't work anymore on the Windows XP: internet connection - but I can see the MAC address on the wireless router IIS - Ping on 127.0.0.1 it's ok as I can hit localhost:8222 nor localhost Does anyone knows how to fix any of this? (at least the internet connection)

  Read the article

• supervisord launches with wrong setuid

  - by friendzis

  I am trying to test a pilot system with nginx connecting to uwsgi served application controlled by supervisord running on ubuntu-server. Application is written in python with Flask in virtualenv, although I'm not sure if that is relevant. To test the system I have created a simple hello world with flask. I want nginx and uwsgi both to run as www-data user. If I launch uwsgi "manually" from root shell I can see uwsgi processes runing as appropriate user (www-data). Although, if I let supervisor launch the application something strange happens - uwsgi processes are runing under my user (friendzis). Consequently, socket file gets created under wrong user and nginx cannot communicate with my applicaion. note: the linux server runs as Hyper-V VM, under Windows Server 2008. Relevant configuration: [uwsgi] socket = /var/www/sockets/cowsay.sock chmod-socket = 666 abstract-socket = false master = true workers = 2 uid = www-data gid = www-data chdir = /var/www/cowsay/cowsay pp = /var/www/cowsay/cowsay pyhome = /var/www/cowsay module = cowsay callable = app supervisor [program:cowsay] command = /var/www/cowsay/bin/uwsgi -s /var/www/sockets/cowsay.sock -w cowsay:app directory = /var/www/cowsay/cowsay user = www-data autostart = true autorestart = true stdout_logfile = /var/www/cowsay/log/supervisor.log redirect_stderr = true stopsignal = QUIT I'm sure I'm missing some minor detail, but I'm unable to notice it. Would appreciate any suggestions.

  Read the article

• Poor gaming performance with hyper-v installed in windows 8

  - by SnowCrash

  I am getting very poor gaming performance on my Windows 8 host OS with Hyper-V installed but no guest machines running. For example World of Tanks reports 60-70 FPS without Hyper-V installed and 4-14 FPS with it installed. A similar, dramatic, hit is observed in several other games so the issue is not WoT specific. To make the point clear, I am not trying to run games in a virtual machine. I don't even have a VM running while observing this effect. I simply have the Hyper-V feature installed. My system specs: AMD Phenom II 965 (3.4 GHz) AMD Radeon 6950 2GB (XFX Double D HD-695X-CDFC) 16GB DDR3 1333 AMD 790GX chipset Mainboard (Gigabyte GA-MA790GPT-UD3H) I have tried every AMD driver from 12.8 to the current 12.11beta8, virtualization is enabled in the BIOS settings, the onboard 3300HD video device is disabled in BIOS and I have read the MSDN blog entry here regarding a similar issue in Server 2008 that was resolved in 2008 R2 (and hopefully not regressed in Win 8). I'd like to be able to use Hyper-V for development and testing at home (I am a sysadmin/software developer professionally). If, however, I can't also use my home system for entertainment I'll have to scrap those plans.

  Read the article

• Migrating Windows 2003 File Server Cluster to Windows 2008 R2 Standalone?

  - by Tatas

  We have a situation where we have an aging Windows 2003 File Server Cluster that we'd like to move to a standalone Windows Server 2008 R2 VM that resides in our Hyper-V R2 installation. We see no need to keep the Clustering as Hyper-V is now providing our Failover/Redundancy. Usually, in a standalone file server migration we migrate the data, preserving NTFS permissions and then export the sharing permissions from the registry and import them on the new server. This does not appear possible in this instance, as the 2003 cluster stores the sharing permissions quite differently. My question is, how would one perform this type of migration? Is it even possible? My current lead is the File Server Migration Toolkit, however I can find no information on the net about migrating from cluster to standalone, only the opposite. Please help. UPDATE: We ended up getting the data copied over (permissions intact), but had to recreate the shares manually by hand. It was a bit of a pain but it did in the end work out.

  Read the article

• Redundant Microsoft server solution for small company

  - by MadBoy

  I'm planning to change one server Microsoft SBS 2003 with SharePoint, Exchange and SQL database into something that will provide me with some redundancy and won't be single point of failure. I was thinking to buy 2x exactly the same physical servers and put 2 virtualized servers on HyperV or VMWare on each. Then i would put SharePoint, Exchange and SQL on that 1 physical server (shared onto 2x VM's). I would like 2nd physical server to be exact duplicate of the first one so that when 1st server goes down (for reboot or hw failure), 2nd takes care of everything so that users don't even see anything changed (in terms all their emails, sharepoint stuff is available). My questions are: Will I have to pay for licenses for both servers even thou only one instance of SharePoint, Exchange, SQL will be used at same time? What are proposed solutions to do that? Any additional hardware I would need, any complicated software configuration to be expected to configure such redundancy so that when one physical server goes down 2nd one is taking care of rest? What problems should I expect? This solution is for 60 people. Later on it may or may expand.

  Read the article

• Instabilities with Bridged and bonded interfaces

  - by Henry-Nicolas Tourneur

  I did post yesterday to get a working setup with several bridged interfaces used for virtual machines (KVM/libvirt). One of the bridged interface is just using eth3 as its ports while the second one (public traffic) is using an ethernet bonded interface. That setup is working but not all the time ! I can start a download from a vm, then it will stop and freeze! So I don't know if my bridge parameters are correct, could you check the below config ? iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.255 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.255 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.255 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.255 And yes, it also sometimes speaks about martian on the host: kernel: [249146.055172] martian source 10.160.0.17 from 10.160.0.10, on dev vnet2 kernel: [249146.073122] ll header: ff:ff:ff:ff:ff:ff:54:52:00:76:c3:5c:08:06

  Read the article

• Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

  - by knda

  I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

  Read the article

< Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >