Search Results

Search found 11482 results on 460 pages for 'portable device'.

Page 146/460 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

• Windows Audio Issue

  - by Nikki

  This one is driving me nuts. Hoping someone can shed some light. I'm running windows 7 using onboard audio. It's been fine for over 2 years but lately there's a problem every time I play audio. I hear a small soft burst of static and the volume turns itself down from 50% to 23%. Once at 23%, it plays fine. No related events logged in viewer. No reported problems with the device. Different headphones, same problem. I played around with audio settings for hours but the problem persists. EDIT: ok more info: Motherboard: ECS G31T-M LGA775 System info displays this: Name High Definition Audio Device Manufacturer Microsoft Status OK PNP Device ID HDAUDIO\FUNC_01&VEN_1106&DEV_E721&SUBSYS_10192683&REV_1001\4&3D4E739&0&0001 Driver c:\windows\system32\drivers\hdaudio.sys (6.1.7600.16385, 297.00 KB (304,128 bytes), 14/07/2009 9:51 AM) I'll keep adding info as I find it. The question I want resolved is; Is it faulty hardware? If so, I can buy a sound card. I can't imagine software is responsible since I haven't installed anything new for weeks. Virus scans are clear as well. The static burst is irritating to say the least. Tried 2 different headphones and separate speakers. Same problem. I know it's not an easy problem but I was hoping someone had encountered the same thing.

  Read the article

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• frequent "SNMP error" with Cacti

  - by nn4l

  When adding new devices to my Cacti instance, I get frequent "SNMP error" messages in the device screen. But the error is not consistent, not even for the same device. Here's what I already have checked: Sometimes a device shows that "SNMP error" message even when it did not had that error an hour before, and vice versa. I tried this with several different Cacti releases, installed on different OS (Debian squeeze: 0.8.7g-1+squeeze1, Debian Sid: 0.8.7i-3, CentOS 6.0: 0.8.7i-2.el6) tried both from a local (192.168.1.xy) network and from a different data center so I don't think it is a network problem reinstalled the Cacti database, rerun the scripts to install my devices. Now different devices have that error when executing a snmpwalk or snmpgetnext command from the command line, it is always successful increasing the timeout to 20000 (20 seconds) and the retry count to 10 does not make a difference The cacti.log says: 04/14/2012 02:10:19 PM - CMDPHP: Poller[0] WARNING: SNMP GetNext Timeout for Host:'s0026.mydomain.de', and OID:'.1.3.6.1.2.1.1.3.0' 04/14/2012 02:10:20 PM - CMDPHP: Poller[0] WARNING: SNMP GetNext Timeout for Host:'s0026.mydomain.de', and OID:'.1.3' However, when executing snmpget or snmpget with that from the command line a proper response is returned immediately.

  Read the article

• What's up with stat on MacOSX/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on MacOSX 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev <volfs> 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) <volfs> on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputting the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• Verification of files on backup media - after the backup

  - by Greg Sansom

  I have a system in place where I back up my work files daily to a portable hard drive. I actually have two portable hard drives - one is stored off-site and I swap them regularly. I also keep my family photos and other historical files backed up, but I only back the photos up occasionally (ie when I have new photos). The backup media is for backup only, and it is unlikely I will ever read the files from the backup media unless a disaster occurs and I lose the master. It worries me that my backed up files could become corrupt without me knowing it. It is also feasible that my master files could become corrupt, and eventually the corrupt files would be replicated to the backup media. I'm currently using Cobian Backup, but I'm open to alternatives. Is there a tool I can use to confirm that the backed up files are identical to the files that were first copied? I know it would be possible to generate a checksum and periodically validate the backup files against the original checksum, but I'm looking for a tool which will do this automatically.

  Read the article

• Looking for cheap Wireless router, with USB for attached USB disk drive

  - by geoffc

  I have a 802.11b router at home (DLink DI-614+ (B rev)) and it is working perfectly well for me. I want to replace it though, since it is out of updates, and now several years old and heck, I want a new toy to configure! I was trying to decide what to get. I could care less about 802.11g or n support, since B is fast enough, but every device in my house is now B/G, so G would be fine for me. N buys me little to nothing. (Small enough house that range is a non-issue). The features I realized I want are a USB port for sharing a USB hard drive. I would like to have a central device I could store files on. I do not want to waste the power of an always running PC to do this, so a router seems like the place to go. I would love it, if it could support Vonage VOIP as well, then I could ditch a power brick from a second device (I have the small DLink Vonage VOIP box). All the current examples of this router (with USB drive, yet to find one with VOIP too!) are in the $100+ range, and N and silly, when a B/G is in the $30 range around here.

  Read the article

• Sparc v440 unable 2 boot after recommended patch install

  - by user100660

  After installing the October 2011 recommended patch bundle on a Solaris 10 the host fails to boot. The output is {0} ok boot SC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Sun Fire V440, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.10.10, 8192 MB memory installed, Serial #54744555. Ethernet address 0:3:ba:43:55:eb, Host ID: 834355eb. Rebooting with command: boot Boot device: /pci@1f,700000/scsi@2/disk@0,0:a File and args: \ Evaluating: Out of memory Warning: Fcode sequence resulted in a net stack depth change of 1 Evaluating: Evaluating: The file just loaded does not appear to be executable. {3} ok If I do a boot -F failsafe the host come up and I'm able to mount the root device (ufs on /dev/dsk/c1t0d0s0) and nothing appears broken, i.e I can see the logfiles from the patch install etc. Root device still have 1GB+ free. Only 2 kernel patches was installed from the patch bundle: 144500-19 & 147440-02. Any hints how to debug it further, etc.

  Read the article

• BES Express - configure MDS to push messages from 3rd party web application

  - by Max Gontar

  Hi! I have developed IIS web service to send PAP messages using Blackberry Push API over MDS. And there is an application installed on device, configured to receive push messages on appropriate port. Everything works well on MDS simulator. But it's not working well in real environment: I have installed BES Express and register several devices. I can browse MDS url with appropriate port, so url is correct. Also port enabled for reliable pushes is used in push message and in device application. Here is MDS simulator log: <2011-01-12 14:00:03.456 EET>:[272]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = PapServlet: request from 0:0:0:0:0:0:0:1 564 bytes...> <2011-01-12 14:00:03.476 EET>:[273]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Mapping PAP request to push request for pushID:pushID:asdas> <2011-01-12 14:00:03.479 EET>:[274]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = PushServlet: POST request from [UNKNOWN @ 0:0:0:0:0:0:0:1] to [PAPDEST=WAPPUSH%3D2100000A%253A100%2FTYPE%3DUSER%40rim.net&PORT=100&REQUESTURI=/] : -1 bytes...> <2011-01-12 14:00:03.480 EET>:[275]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = submitting push message with id:pushID:asdas> <2011-01-12 14:00:03.482 EET>:[276]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Executing push submit command for pushID:pushID:asdas> <2011-01-12 14:00:03.483 EET>:[278]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Pushing message to: 2100000a> <2011-01-12 14:00:03.484 EET>:[279]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Number of active push connections:1> <2011-01-12 14:00:03.489 EET>:[280]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = added server-initiated connection = -872546301, push id = pushID:asdas> <2011-01-12 14:00:03.491 EET>:[281]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Available threads in DefaultJobPool = 9 running JobRunner: DefaultJobRunner-7> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION => <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Transmission Line Section]:> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = POST / HTTP/1.1> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Headers Section]: 8 headers> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Parameters Section]: 3 parameters> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION => <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Transmission Line Section]:> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = POST / HTTP/1.1> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Headers Section]: 9 headers> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Parameters Section]: 3 parameters> <2011-01-12 14:00:03.501 EET>:[284]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Finished JobRunner: DefaultJobRunner-7, available threads in DefaultJobPool = 10, time spent = 8ms> <2011-01-12 14:00:03.521 EET>:[287]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = CreatedSendingQueue, DEVICEPIN = 2100000a> <2011-01-12 14:00:03.526 EET>:[290]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = Sending, TAG = 1288699908, DEVICEPIN = 2100000a, VERSION = 16, CONNECTIONID = -872546301, SEQUENCE = 0, TYPE = NOTIFY-REQUEST, CONNECTIONHANDLER = http, PROTOCOL = TCP, PARAMETERS = [MGONTAR/10.10.0.35:100], SIZE = 339> <2011-01-12 14:00:03.531 EET>:[291]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Number of active push connections:0> <2011-01-12 14:00:03.591 EET>:[292]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = Notification, TAG = 1288699908, STATE = DELIVERED> <2011-01-12 14:00:03.600 EET>:[296]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Device connections: AVG latency (msecs)79> <2011-01-12 14:00:03.600 EET>:[297]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, Removed push connection:-872546301> <2011-01-12 14:00:07.015 EET>:[298]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = RemovedSendingQueue, DEVICEPIN = 2100000a> And here is real MDS log: <2011-01-12 11:35:02.763 GMT>:[3932]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, PapServlet: request from 192.168.1.241 583 bytes...> <2011-01-12 11:35:02.897 GMT>:[3933]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Mapping PAP request to push request for pushID:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.909 GMT>:[3934]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, PushServlet: POST request from [UNKNOWN @ 192.168.1.241] to [PAPDEST=WAPPUSH%3D22D7F6BD%253A7874%2FTYPE%3DUSER%40rim.net&PORT=7874&REQUESTURI=/]> <2011-01-12 11:35:02.909 GMT>:[3934]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<push id: pushID:sdfsdfwerwer> <2011-01-12 11:35:02.910 GMT>:[3935]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, submitting push message with id:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.910 GMT>:[3936]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Executing push submit command for pushID:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.911 GMT>:[3937]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Pushing message to: 22d7f6bd> <2011-01-12 11:35:02.912 GMT>:[3938]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Number of active push connections:1> <2011-01-12 11:35:02.931 GMT>:[3939]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, added server-initiated connection = -1848311806, push id = pushID:sdfsdfwerwer> <2011-01-12 11:35:03.240 GMT>:[3940]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = CreatedSendingQueue, DEVICEPIN = 22d7f6bd, USERID = u3> <2011-01-12 11:35:03.241 GMT>:[3941]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = Sending, TAG = 536543251, DEVICEPIN = 22d7f6bd, USERID = u3, VERSION = 16, CONNECTIONID = -1848311806, SEQUENCE = 0, TYPE = NOTIFY-REQUEST, CONNECTIONHANDLER = http, PROTOCOL = TCP, PARAMETERS = [LDN-Server1/192.168.1.240:7874], SIZE = 383> <2011-01-12 11:35:03.241 GMT>:[3942]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Number of active push connections:0> <2011-01-12 11:35:03.253 GMT>:[3943]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Sending, VERSION = 1, COMMAND = SEND, TAG = 536543251, SIZE = 570> <2011-01-12 11:35:03.838 GMT>:[3944]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Receiving, VERSION = 1, COMMAND = STATUS, TAG = 536543251, SIZE = 10, STATE = DELIVERED> <2011-01-12 11:35:04.104 GMT>:[3945]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = Notification, TAG = 536543251, STATE = DELIVERED> <2011-01-12 11:35:04.121 GMT>:[3946]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Device connections: AVG latency (msecs)893> <2011-01-12 11:35:04.135 GMT>:[3947]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<INFO >:<LAYER = IPPP, DEVICEPIN = 22d7f6bd, DOMAINNAME = LDN-Server1/192.168.1.240, CONNECTION_TYPE = PUSH_CONN, ConnectionId = -1848311806, DURATION(ms) = 1151, MFH_KBytes = 0, MTH_KBytes = 0.374, MFH_PACKET_COUNT = 0, MTH_PACKET_COUNT = 1> <2011-01-12 11:35:04.144 GMT>:[3948]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, Removed push connection:-1848311806> <2011-01-12 11:35:09.264 GMT>:[3949]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = RemovedSendingQueue, DEVICEPIN = 22d7f6bd, USERID = u3> <2011-01-12 11:35:58.187 GMT>:[3950]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Sending, VERSION = 1, COMMAND = INFO, SIZE = 46> <2011-01-12 11:35:58.187 GMT>:[3951]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Sent health to S27700165[LDN-SERVER1:3200] Health=[0x 0000 0007 0000 0000],Mask=[0x 0000 0007 0000 0000],Load=[60]> As you can see, logs not really differs, message is marked as delivered. But my app on device not really gets this message (as it works in mds simulator) Please advice me, what may be wrong? Is there some certificate to install or security settings I should configure to make this push message came to device application? Thank you! same question on bbforums

  Read the article

• Choosing the right TV tuner - USB or PCI TV tuners, hardware/software, DVB? Hybrid/combo/analog?

  - by Nucleon

  Greetings, I'll start with some background information so you know what I'm trying to accomplish and then get to my question. I work at a Television station in the US and we are working on setting up an online DVR/Podcast system for all of our newscasts. So basically we would be recording every newscast in HD, encoding it to flv/h.264 for viewing in a browser on flash compatible and iphone/ipad devices, eventually migrating to WebM when it's browser compliant. This task is theoretically pretty simple as it all it involves is a TV tuner device and a program like VLC, MythTV or whatever to schedule and dump it to a file, encode it with VLC/FFMPEG and push it to the streaming server. Now to the hardware, in order to accomplish that task, should I use an internal PCI tuner or a USB 2.0 tuner? Is there a difference? The bus speeds of both are not too far apart, and is the bus speed really relevant in this case? Does it matter if the device has a hardware encoder or a software encoder? On many sites the USB was recommended for ease of set up and use, but would it overly task a processor, or is that not a concern as long as it's a decent PC (at least duo core, 6gb ram). What's the difference between the stick USB and the Box USBs? To my understanding analog is basically gone in the US, so we would want a hybrid or combo tuner correct? How do those differ from DVB? Are there any other features or concepts which I am missing which may influence the recommended product. It would be ideal if the device which could work in both Linux and a Windows environment, to my knowledge most Hauppauge are? Example 1: PCI Hauppage http://www.newegg.com/Product/Product.aspx?Item=N82E16815116033 Example 2: USB 2.0 Box http://www.newegg.com/Product/Product.aspx?Item=N82E16815116029 Example 3: USB 2.0 Stick http://www.newegg.com/Product/Product.aspx?Item=N82E16815116031 Any guidance from the Superusers would be much appreciated!

  Read the article

• Connect bluetooth headphones both to PC and phone at the same time

  - by Sergiy Byelozyorov

  I have recently bought Philips SHB6110. Extract from the 13th page of manual: Therefore you can connect your Bluetooth stereo headset. with a Bluetooth stereo enabled phone to both listen to music and lead calls, or with a Bluetooth phone that does not support Bluetooth stereo (A2DP) to lead calls and at the same time to a Bluetooth audio device (Bluetooth enabled MP3 player, Bluetooth audio adapter etc.) to listen to music. Make sure to pair the phone first with your Bluetooth headset, then turn both the phone and headset off to then pair the Bluetooth audio device. With the SwitchStream feature you can listen to music and monitor your calls at the same time. Even while listening to music, you will hear a ring tone when receiving a call and can switch to the call simply by tapping the button. The manual however doesn't specify how do I connect to both device at the same time. I use Toshiba Satellite Pro P300-1CG laptop with Belkin Mini Bluetooth Adapter and Nokia N95 phone. Operating system is Windows 7 64-bit and I have Skype installed. Both phone and compute can be used for listening to music and talking on the phone (on PC via Skype). Best solution would be if I could connect to PC and phone as the same time and monitor calls both mobile and Skype calls while listening music from Winamp. If that is not possible, then I would like at least to be able to listen music from PC, while monitoring calls from mobile. So, please tell me how do I connect both PC and phone to headphones?

  Read the article

• How do I use a self encrypting drive?

  - by Unique_Key

  I recently purchased a Micron RealSSD c400 self encrypting drive, and I am having a few issues when trying to get it recognized by my laptop (HP Elitebook 8440p running Windows 7 x64; also tried on a custom-built desktop). When I try to initialize the drive from disk management, I get a CRC error; also, when attempting to partition it from Windows setup, the program can't create the partitions. I also tried with UBCD, nothing. I assume this is due to drive security, but I haven't been able to find much information about this online; do I need a management software or something? I'm completely stumped here. EDIT As requested, when I try partitioning the device from Windows setup I get a 0x80300024 error; when I try initializing it from disk management, I get a "Data error (cyclic redundancy check)" message, and the event log shows the following under System: Source: VDS Basic Provider, message: unexpected failure. error code 490@01010004 (2x) Source: Virtual Disk Service, message: VDS fails to write boot code on a disk during clean operation. Error code: 80070001@02070008 (1x) Source: Disk, message: The device \Device\Harddisk2\DR2 has a bad block (2x) The security logs show nothing related. Also, when attempting to configure it from UBCD (utility: HDAT2), I get an error along the lines of "can't edit partition information" or something to that tune.

  Read the article

• I keep losing wireless connection

  - by posfan12

  I have a WRT54GL v1.1 wireless router and a WUSB54G v4 wireless adapter, both made by Linksys. The router is in the living room by the TV and the my computer is in the bedroom. My ISP is Brighthouse. Operating System Microsoft Windows 7 Home Premium 64-bit SP1 CPU Intel Core 2 Duo E6600 @ 2.40GHz 36 °C Conroe 65nm Technology RAM 3.00GB Single-Channel DDR2 @ 333MHz (5-4-4-14) Motherboard eMachines EMCP73VT-PM (CPU 1) 26 °C Graphics ASUS VS247 (1920x1080@60Hz) 767MB GeForce GTX 460 (nVidia) 43 °C Hard Drives 466GB Seagate ST350041 8AS SCSI Disk Device (SATA) 35 °C Optical Drives HL-DT-ST DVDRAM GH41N SCSI CdRom Device Audio High Definition Audio Device The problem is that my Internet connection will work fine for 15 minutes or so. Then the data will just stop flowing. Windows says I am still connected, and the systray icon still shows five bars. But Comodo Firewall will stop showing up and down traffic, and another of my systray applications complains about a lack of connection. What I usually do is either disconnect from the network manually, or unplug and re-plug the USB adapter. At which point the connection will work properly for another 15 minutes. I've tried unplugging my router for 30 seconds and letting it reboot. I've also tried looking for a newer driver for my adapter but I seem to have the latest version 3.1.3.0. This is a recent problem starting about a week ago. For the previous several months things were working just fine. I haven't made any changes to my system that I am aware of. The only thing I did was open my case to blow the dust out of it, then put everything back together. How do I fix this issue?

  Read the article

• Linux NIC Bonding Issue (CentOS 4 / RHEL 3)

  - by jinanwow

  I am having an issue with bonding NICs on CentOS 4. It appears the bonding driver does work, but it is stuck in round-robin mode and I am trying to get to active-backup. The current config is: ifcfg-bond0 DEVICE=bond0 IPADDR=192.168.204.18 NETMASK=255.255.255.0 ONBOOT=yes BOOTPROTO=none USERCTL=no TYPE=Bonding BONDING_OPTS="mode=1 miimon=100" ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes TYPE=Ethernet MASTER=bond0 SLAVE=yes ifcfg-eth3 DEVICE=eth3 ONBOOT=yes BOOTPROTO=none TYPE=Ethernet MASTER=bond0 SLAVE=yes cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v2.6.3-rh (June 8, 2005) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:17:a4:8f:94:b1 Slave Interface: eth3 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:1b:21:56:b8:69 cat /etc/modprobe.conf alias eth0 tg3 alias eth1 tg3 alias eth3 e1000 alias eth2 e1000 alias bond0 bonding options bond0 mode=1 miimon=100 I have tried moving the bonding information out of the ifcfg-bond0 into the modprobe configuration file. It seems that it is stuck in RR and I am trying to get it into the Active-backup (mode 1) state. Any ideas what would be causing this issue?

  Read the article

• SQL Server restore a backup results in an error.

  - by Mario

  I have a database in dev (SQL Server 2005 on Windows Server 2008) that I need to move to prod (SQL Server 2000 on Windows Server 2003). My process is as follows: Login to dev, open SQL Server Management Studio Right click on the database | Tasks | Backup. Keep all default options (full backup etc.) Move .bak file locally to prod (no network drive), login to prod, open SQL Server Enterprise Manager. Right click Databases node | All Tasks | Restore database. Change Restore as database to reflect the same database name. Click radio button 'From device'. Click 'Select Devices' Click Restore from: Add..., browse to .bak file (small - only 6mb) Now I am ready to restore the database, so I click OK and get the following error: "The media family on device 'E:...bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE DATABASE is terminating abnormally." This error is immediate. I have tried a few different variations of this - restoring the db to dev machine with a different db name and log file names (where it originated), creating an empty database with the same physical path to files before and trying to restore to that, making a few different .bak files and making sure they are verified before uploading them to prod. I know for a fact the directory for the .mdf and .ldf files exist on prod, though the files themselves don't exist. If, before I click OK to restore, go to the options tab instead I get the following error: Error 3241: The media family on device 'E:...bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE FILELIST is terminating abnormally. Anyone have any bright ideas?

  Read the article

• Most transparent way to connect two LANS using a WET610N Wireless Bridge

  - by Spencer Ruport

  I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Prolific USB-to-Serial Comm Port significantly slower under Windows 7 comparing to Windows XP

  - by Dmitry S

  Not sure if this question should be asked here or on SuperUser but if we get an answer here it may be useful for others here I am using a Prolific USB-to-Serial adapter based on the Prolific chip to use with a device on serial port. I have the latest version of the driver installed: 1.3.0 (2010-7-15). When I use my device with this adapter on my main Windows 7 (32bit) system it takes 8-9 seconds to send a command through to the device. However, when I do the same thing on a different Windows XP system (an old laptop I borrowed for testing) it only takes 2-3 seconds. I have made sure that the port settings and other variables are the same between systems. I also tested on a third laptop (also running Windows 7) and again got a significant delay. So the question is if anyone else experienced the same problem and found a solution. I would like to avoid moving to an XP system for what I need to achieve so that's my last option. Thanks in advance.

  Read the article

• Filtered Router Interface

  - by jviotti

  I'm having some problems with a Scientific-Atlanta DPR2320R2. In specific with the WIFI. A few months ago I changed its password and username and now I can't remember. So I tried cracking it with Hydra but it drove things worse. Content of webadmin was rendered partial, and threw lot of errors. I then reseted the router. I found myself abled to browse the web with ethernet-connected pc. Wifi is configured by registering the device's MAC Address, and indeed the router has been reseted and register MAC address were lost. No device could connect to wifi. In fact, the device does not even recognize the network. I tried the pointing to 192.168.0.1 to restablish the MAC's. But I couldn't connect to the router access point. Tried listing up hosts: $ nmap -sP 192.168.0.0/24 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:18 ART Host 192.168.0.1 is up (0.0018s latency). Host 192.168.0.11 is up (0.00025s latency). Nmap done: 256 IP addresses (2 hosts up) scanned in 59.62 seconds Then checked 192.168.0.1 was really up by sending pings. It responded to all my pings. I quick-scanned the access point: $ nmap 192.168.0.1 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:08 ART Interesting ports on 192.168.0.1: Not shown: 999 closed ports PORT STATE SERVICE 80/tcp filtered http Nmap done: 1 IP address (1 host up) scanned in 6.73 seconds Look the state of the port 80: FILTERED. I'm pretty confused now. Any suggestion would be appreciated. Thanks in advance.

  Read the article

• Windows XP consuming drive letters

  - by billdehaan

  This one's a bit of a stumper. I'm running XP SP3, current with all fixes, etc. My problem is that I can assign a drive letter to a container file (explained below), it works just fine. But once I close the container, the drive letter is no longer available until the next boot. I've got some confidential data that I've placed in a container volume. I've used TrueCrypt (www.truecrypt.com) and FreeOTFE (www.freeotfe.org), with both installed and portable versions for both, with the same result. I open the container file, assign it to a drive letter (say R:), and run some portable apps that are within the volume. When I'm done, I close the container, and the drive letter is released. Fine so far. However, when I attempt to re-open it, the previous drive letter (in this case R:) is no longer available. It's not mapped to anything, it's just unavailable. Even attempting something like "subst R: C:\" returns "Invalid Parameter - R:". I can use the S: drive, no problem, but the next day I have to use T:, then U:, etc. Eventually, I have to reboot to reclaim all of of the drive letters. Unfortunately, everything I've read about drive letters relates to USB assignments, which doesn't apply here. I've tried the "show hidden" command (set devmgr_show_nonpresent_devices=1) with no success. And the Disk Management tool doesn't apply either, since it's not a physical drive. Does anyone know where Windows keeps the list of drive letters? And is there anything short of a reboot that can be used to reset it?

  Read the article

• corrupted, hidden, wireless network adapter from "Network Connections" in Windows 7

  - by srihari reddy

  The issue is that when I install a wireless network adapter on my Windows 7 Professional machine I have no connectivity, the system tray icon has a red X. First, I tried the obvious, install updated drivers from the manufacturer. When I did this, the Network Connections icon had gray bars and there was no connectivity. So I tried installling the network adapter on a different computer on the same network and I verified that it does work with no issues. Next, I ran scan disk with no issues. Next, I ran sfc as admin with no issues. At this point I turned to the router and turned SSID broadcast on but that didn't help. I turned MAC address filtering off at the router but that didn't help. Whenever I installed the original network adapter (a wireless N usb adapter with WPA2 TKIP+AES) it showed up as "Wireless Network Connection 2" with a grayed out icon and no connectivity. Lastly, I tried installing two different "verified working" usb wireless adapters on to the Windows 7 Pro machine. The results were the same "Wireless Network Connection 2" that had a green bar icon but no connectivity. I installed the manufacturers software and it indicated the NIC was not there even thought the driver installed successfully in Device Manager. I guess I should mention, I first tried (insanely in vain) to use the (worthless) Windows Network troubleshooter. The results were....drumroll please... There is a problem with the network adapter... well No Duh! Also, during all of this the network adapter is always showing as "Working Properly" in the properties dialogue of Device Manager for the wireless NIC. I checked for hidden devices in Device Manager but there were none. Here is my fundamental question that I've tried to find in the Windows 7 support center with no luck. How do I remove/delete/uninstall network adapters from the Windows 7 registry? in particular hidden, corrupted network adapters, that used to be working.

  Read the article

• Diverting sound output of MCE to SPDIF

  - by Saxtus

  I have an ASUS SupremeFX II audio card (which in fact is an onboard audio riser slot) with the default drivers that are pre-installed by Windows 7 x64 for this card. I am able to manually switch between analog output and SPDIF output by the means of control panel (or external utilities like STADS), a change that affects all applications. The problem is that by doing that every time I am about to launch Windows Media Center, except that it's not that elegant, also makes all other Windows application's sounds to pass through SPDIF too, bypassing analog output completely, blending with what I am watching at Windows Media Center. Is there a way to make SPDIF as the default playback device for Windows Media Center? I know other programs that have a setting like that (foobar2000 for example) working like charm, allowing me to even have different outputs working at the same time (tested with my current card successfully). But when comes to Windows Media Center... it just use what the default playback device is all the time. The only setting that I know of, is under: Settings General Windows Media Center Setup Set Up Your Speakers and what it does is to just change the default playback device for entire system. Please help!

  Read the article

• What's up with stat on Macos/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Macos 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputing the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• What's up with stat on Mac OS X/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Mac OS X 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev <volfs> 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) <volfs> on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputting the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• What GPT partition type to use for protecting DRBD metadata?

  - by Carsten Scholtes

  I'm planning to install a DRBD device on a (replicated) disk with two GPT partitions. DRBD requires some space for (preferentially "internal") metadata at the end of the underlying device. I'm hesitant to leave this space unpartitionend (or unformatted in a normal partition). I'd like to reserve an extra partition at the end of the underlying disk device for the metadata. (If I understand correctly, DRBD would not care about the partition or its type and could then use that space exclusively.) My question is: Which would be a suitable GPT partition type for such a metadata partition? It should not be a type interpreted while booting (such as EF00 EFI System). It should not be a type prone to be modified accidentialy by the booted OS (such as 8200 Linux swap, 8e00 Linux LVM, fd00 Linux raid). (The booted OS will be Ubuntu Linux 12.04.3.) It should not be a type indicating a normal filesystem (such as 0c01 or 8301), prone to be formatted correspondingly. It should not be a type requiring any special content in the partition (since the content is to be handled exclusively by DRBD). It should express the purpose of being reserved for something special (namely DRBD). (The types I listed are as provided by gdisk. I'm thinking about using some type unlikely to be used by the OS (maybe bf0a Solaris Reserved 4) or an invented(?) type such as fd01 (close to fd00 Linux raid…). Would something like this be suitable, too dangerous or even possible?)

  Read the article

• None of usb-controllers are working after a crash

  - by Cray

  So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

  Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >