Search Results

Search found 4575 results on 183 pages for 'tutorial'.

Page 146/183 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

• Why are my socks proxies slow

  - by vps_newcomer

  I have a linux vps, and i have tried a few socks proxy setups to test their performance: All tests were using speedtest.net The standard ssh tunnel proxy 0.8mbit/s download and 0.1-0.2mbit/s upload speeds dante-server proxy 1.3mbit/s download and 0.4-0.5mbit/s upload I am wondering why are these speeds so slow? Is anything shaping them? Is it just the nature of socks proxies? I know that the ssh tunnel has to do encryption and what not so that is why its slow, but i was surprised to see that the second setup was also quite slow. On the VPS i have received download speeds of 25MB/s per second (thats about 200mbit/s and upload speed of atleast 5MB/s (haven't got a good enough pipe to test anything faster). The other option i was going to try is to setup OpenVPN and see how that goes, however i need to find a good tutorial as it's fairly complicated to setup. So why is it so slow? How can i test to see where the bottleneck is? How can i make it faster :D

  Read the article

• FreeBSD ZFS RAID-Z2 performance issues

  - by Axel Gneiting

  I'm trying to build my own network attached storage based on FreeBSD+ZFS+standard components, but there are strange performance issues. The hardware specs are: AMD Athlon II X2 240e processor ASUS M4A78LT-M LE mainboard 2GiB Kingston ECC DDR3 (two sticks) Intel Pro/1000 CT PCIe network adapter 5x Western Digital Caviar Green 1.5TB I created a RAID-Z2 zpool from all disks. I installed FreeBSD 8.1 on that zpool following the tutorial. The SATA controllers are running in AHCI mode. Output of zpool status: pool: zroot state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raidz2 ONLINE 0 0 0 gptid/7ef815fc-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/80344432-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/81741ad9-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/824af5cb-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/82f98a65-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 The problem is that write performance on the pool is very very bad (<10 MB/s) and every application that is accessing the disk is unresponsive every few seconds when writing. It seems like writing is fine until the ZFS ark cache is full and then ZFS stalls the entire system I/O till it's finished writing that data. Also I'm getting kmem_malloc to small kernel panics. I've already tried to put vm.kmem_size="1500M" vm.kmem_size_max="1500M" into /boot/loader.conf, but it doesn't help. Does anyone know what's going on here? Am I really not having enough memory for ZFS to handle this RAID-Z2?

  Read the article

• A-2-Z web hosting on Amazon AWS

  - by JDelage

  All, I am studying web dvp, and one of my classes is project-based. We have to build a functional site that demonstrate our understanding of: HTML, CSS, Javascript, php, MySQL, And potentially Ajax or some other web component. For the project, we can use a local server using WampServer and basically build the site entirely on our laptop. If I have time, I would like to create a real site, and I thought it would be a good way to familiarize myself with Amazon's AWS services. So if I purchase a domain name, can I rely on AWS to host the site from A-to-Z? I understand I can use AWS to host content, the database, and do the background computations, if needed. What else do I need and what are the parts that AWS cannot help me with? Second, is there good documentation for a beginner to navigate AWS and learn how to use it (either on Amazon, or some 3rd party sites, or even a good book, as long as is up to date). The ideal documentation would be a tutorial on creating a web site from a-to-z on AWS, as detailed as possible. As you can guess, I have limited understanding of the IT issues. I have 0 Linux or sysadmin experience, but this is a good opportunity to change that. I hope you can help me. Thank you, JDelage PS: Please keep the answers AWS-specific. At this point, I am only interested in alternative services to the extent that they plug a hole in Amazon's offering.

  Read the article

• Mac updated just now, postgres now broken

  - by Dave

  I run postgres 9.1 / ruby 1.9.2 / rails 3.1.0 on a maxbook air for local dev. It's all been running smoothly for months, (though this is the first time I've done development on a mac.) It's a macbook air from last year, and today I got the mac osx software update message as I have a few times before, and my system downloaded approx 450mb of updates and restarted. It now says it's on OSX 10.7.3. Point is, postgres has stopped working, when I start my thin server (mirror heroku cedar) as normal, and then browse to my rails app I get: PG::Error could not connect to server: Permission denied Is the server running locally and accepting connections on Unix domain socket "/var/pgsql_socket/.s.PGSQL.5432"? What happened? After browsing around a few questions I'm still confused, but here's some extra info: Running psql from command line gives same error I can run pgadmin 3 and connect via it and run SQL no problems Running which psql shows the version as /usr/bin/psql I created a PostgreSQL user back when I got the mac (it's always been on lion) I've no idea why, almost certainly I was following a tutorial which I neglected to store in my notes. Point is I am aware there is a _postgres user as well. I know it's rubbish, but apart from a note on passwords, I don't have any extra info on how I configured postgres - though the obvious implication is that I did not use the _postgres user. Anyone have suggestions or information on what might have changed / what I can try to debug and fix? Thanks. Edit: Playing around based on this question and answer: http://stackoverflow.com/questions/7975414/check-status-of-postgresql-server-mac-os-x, see this string of commands: $ sudo su postgreSQL bash-3.2$ /Library/PostgreSQL/9.1/bin/pg_ctl start -D /Library/PostgreSQL/9.1/data pg_ctl: another server might be running; trying to start server anyway server starting bash-3.2$ 2012-04-08 19:03:39 GMT FATAL: lock file "postmaster.pid" already exists 2012-04-08 19:03:39 GMT HINT: Is another postmaster (PID 68) running in data directory "/Library/PostgreSQL/9.1/data"? bash-3.2$ exit

  Read the article

• How to set up the jdbc driver to connect to hsqldb from libreoffice?

  - by rumtscho

  I am trying to "split" a LibreOffice .odb file into a HSQL database and an OpenOffice document containing forms and macros. I am trying to follow the instructions from this thread: Within a few minutes you can convert your embedded HSQLDB to a stand-alone HSQLDB which is just a very fine database engine. 1) Download and extract the current version from http://hsqldb.org/ and point the Java class path in ToolsOptionsJava to the new hsqldb.jar 2) Extract the database folder from your embedded database and rename the files data, properties, script to name.data name.properties, name.script where "name." is an arbitrary name prefix. 3) Connect a Base document to an existing JDBC database such as jdbc:hsqldb:file:/home/chenier/hsqldb/name;default_schema=true;shutdown=true;hsqldb.default_table_type=cached;get_column_name=false (again, "name" refers to your own file name prefix). This local single-user connection gives you much more than the embedded HSQLDB. 4) Copy queries, forms and reports from the old database over to the new one. The wizard presents me with a window expecting two inputs: a "Datasource URL" and a "JDBC driver class". As far as I can tell, the tutorial above only tells me what to put into the Datasource URL. As for the JDBC driver class, I have no idea what to write into this field. I tried the fully-qualified name of the Java class, org.hsqldb.jdbc.JDBCDriver as given in the HSQLDB documentation. When that failed, I tried the physical path /var/lib/hsqldb/lib/hsqldb.jar (although that should have been unnecessary, because first I pointed to this path as described under 1 and then restarted LibreOffice). In both cases, "Test class" failed with the message "The JDBC driver could not be loaded". OpenOffice's documentation doesn't say anything sensible about the field, it was something like "enter the JDBC driver in this box". Any ideas what I should enter there to get the connection working?

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• Limit copssh users to home directory Windows 7

  - by Siriss

  Hello all- I have found these two sites below: CopSSH SFTP -- limit users access to their home directory only and http://blogs.windowsnetworking.com/wnadmin/2006/11/07/copssh-restricting-users-access/ as well as the Copssh website, but upon completion they do not seem to work. I have copssh installed and I have a separate Windows account "sftpuser" created that is used to connect. The connection works just fine, but I want to limit that user to just their home directory and sub folders. I have 3 hard drives, the C:, a W: and an S: and I want the FTP account to only be able to access the W: drive and its contents (the root of the W: drive is the FTP home directory). Right now "sftpuser" can access all folders, including jump drives to C:, and S:. The linked tutorials do not seem to work, because it seems when I create a group "ftpusersgroup" and add "sftpuser" to the group, and then deny "ftpusersgroup" access to the C: drive, the service breaks and I can no longer login. I have undone everything and am ready to start fresh. Does anyone know how to do this, or is there a better tutorial that someone has or has found? I hope this makes sense. Thank you very much for any help!

  Read the article

• Where is the bare cygwin package list located and how do I manipulate it?

  - by matnagel

  Where is the bare cygwin package list located and how do I manipulate it programmatically or from a shell or with a different method than the gui? I know the gui (setup.exe), and I'd love to go one or more levels deeper. I can retrieve a list of selected/installed packages ( http://serverfault.com/questions/83456/cygwin-package-management ), but how do I write it back or to a different machine? What I have in mind is when I install a new windows I would like to start with my package list in text form, an apply or inject it somehow to the new system. Where is it? In the registry? In a binary file? in a local database? Or has anybody done this, is there a tool, a tutorial? The essence of what I want is to manipulate the selected package list with something else than the gui. It is ok for me to use the gui for the setup process. So I could imagein manipulating the package List and then run setup.exe and just click through it. Note: I do not want to manipulate the list of already installed packages but of packages that "should be installed". But if htis is not possible, maybe there is some workaround. E.g add an outdated version as installed and the installer will then install the new version.

  Read the article

• few basic questions on webhosting (namservers & dns records)

  - by claws

  I bought a domain name on name.com & I want to use free webhosting on 110mb.com By default name.com integrates services of Google apps. Name server entries are ns1.name.com ns2.name.com ns3.name.com ns4.name.com When I registered on 110mb.com it gave me two addresses ns1.110mb.com ns2.110mb.com This is where I'm lost. The concept is that "Domain name should point to an address of the server where the website is hosted" right? Then why are these 4 entires by default. How exactly is it working? should I remove these 4 and then add 110mb.com servers or just append 110mb.com server addresses to name.com ones. I would like to use google apps. If I change these name server addresses would that remove google apps? I especially want to use email service of google. And I really don't understand what is CNAME, MX, or something something. I want to learn about these stuff & how it exactly works. When I search for webhost tutorial. I'm unable to find any fruitful results.

  Read the article

• DKIM- Filter No Signature Data

  - by Vineet Sharma

  I have installed DKIM-Filter on Postfix after reading this tutorial http://www.unibia.com/unibianet/systems-networking/how-setup-domainkeys-identified-mail-dkim-postfix-and-ubuntu-server My email now has a DKIM signature but still it is landing in the SPAM folder. Here is the header Received-SPF: neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=69.164.193.167; Authentication-Results: mx.google.com; spf=neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected]; dkim=hardfail (test mode) [email protected] Received: from promote.a2labs.in (localhost [127.0.0.1]) by promote.a2labs.in (Postfix) with ESMTPA id 34858530E8 for <[email protected]>; Mon, 28 Feb 2011 12:23:07 +0530 (IST) DKIM-Signature: v=1; a=rsa-sha256; c=simple/simple; d=a2labs.in; s=mail; t=1298875987; bh=bo+H1VYPIHMja2u7i1lnzr4k/j4Pe8iSf79bVw94XpI=; h=To:Subject:Message-ID:Date:From:Reply-To:MIME-Version: Content-Type:Content-Transfer-Encoding; b=nhTdlnUwo0iUJ92ycQzKSRjw 5Pfya0DJcJrAc8Mr2hIv8OLpgzBCzdOMWTGqR5nuUmAzgCGYBhYAM2XZwVxo9JG/iz7 oYKysmNQnskFx0TRyW3UOkDWcfHcPnCL6Y7fGzZWinmsyjsg47k+mKZg/e8jqlwTAMO PYKkt5pBz7SM0= Also my mail.err file shows Feb 28 12:17:03 ivineet dkim-filter[32181]: 1F788530E1: no signature data Feb 28 12:18:02 ivineet dkim-filter[32181]: 432BA530E2: no signature data How to fix it

  Read the article

• Do I need to restart my server after editing fstab and mtab?

  - by jaypabs

  I'm just wondering if I need to restart my server after editing fstab and mtab. I changed something in this file manually due to problem with awstats report. I am using ISPConfig 3 with the help of the tutorial from howtoforge. But due to removing/deleting of some account, the configuration of fstab and mtab messed up. I also ask this question at howtoforge forum but until now no one has answered. If you'd like to read my question please visit it here. I tried very hard to fix the problem w/o luck. Update: Here's what happen to my fstab: Before the value was (I omitted the other): /var/log/ispconfig/httpd/mydomain.com /var/www/clients/client1/web1/log none bind,nobootwait 0 0 /var/log/ispconfig/httpd/example.com /var/www/clients/client1/web2/log none bind,nobootwait 0 0 So I changed it to the correct path: /var/log/ispconfig/httpd/mydomain.com /var/www/clients/client1/web2/log none bind,nobootwait 0 0 /var/log/ispconfig/httpd/example.com /var/www/clients/client1/web3/log none bind,nobootwait 0 0 I also found mtab to have the same value as above that's why I edited it manually. from: /var/log/ispconfig/httpd/mydomain.com /var/www/clients/client1/web1/log none rw,bind 0 0 /var/log/ispconfig/httpd/example.com /var/www/clients/client1/web2/log none rw,bind 0 0 to: /var/log/ispconfig/httpd/mydomain.com /var/www/clients/client1/web2/log none rw,bind 0 0 /var/log/ispconfig/httpd/example.com /var/www/clients/client1/web3/log none rw,bind 0 0 I edited those value because the correct path of mydomain.com and example.com should be under web2 and web3 folder respectively. As of now the log of example.com is pointed to: /var/www/clients/client1/web2/log when it should be: /var/www/clients/client1/web3/log So I am thinking that this is because of fstab and mtab. Please guide me how to point the log correctly to it's default directory. I explain the scenario one by one at this link. to dawud: Based on your example mount -o remount,noexec /var, should I run mount -o remount,noexec /var/log/ispconfig/httpd/example.com?

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• Windows 7 mapped drive kicking off OS X users

  - by Collin White

  I've mapped a network drive on my Windows 7 PC at my office. The windows machine has a few TB of storage that is being accessed by my development team (all running mac os 10.7). The share seems to work fine for a little while but will timeout and kick the mac users off and sometimes disallows a connection on the next attempt. Restarting the windows machine fixes the problem. I've tried this tutorial as well as setting the maximum session length in the Local Security Policy section to 99999 (I discovered 0 did not mean unlimited, only a 'reasonable ammount of time') anyway, the setting is now for ~208 days which is sufficient (see attached). I'm having trouble debugging this in general so if anyone has some pointers I'm all ears. This is a intermittent issue which in my opinion are the hardest kinds to debug. If anyone knows of how I might monitor connections from the PC that would also be pretty cool. Previously the files were hosted on a mac mini and everything was working just fine (the mini just didn't have the ability for the storage capacity we needed) so I believe it is some windows setting that is kicking users off. Anyway, thanks for reading.

  Read the article

• NGINX Configuration Error using Codex Example: Is This a Typo in Codex?

  - by jw60660

  I installed NGINX using this tutorial: C3M Digital NGINX Tuturial but after reading this article on security issues with "cut and paste" configuration tutorials: Neal Poole's article regarding security and NGINX configuration I decided to follow Poole's suggestion to use the configuration suggested in the WordPress codex: Codex on NGINX Configuration I used the Codex configuration for a multisite installation using W3 Total Cache. When attempting to start NGINX I get an error saying that the /etc/nginx/nginx.conf test failed. The error message was: "Restarting nginx: nginx: [emerg] unknown directive "//" in /etc/nginx/sites-enabled/teambrazil.com:18" When I looked at my site specific configuration at that path I noticed the rewrite rule in the server block was: rewrite ^ $scheme://teambrazil.conf$request_uri redirect; That line in the Codex example was: rewrite ^ $scheme://mysite.conf$request_uri redirect; That looked like a mistake to me, and I changed my line to: rewrite ^ $scheme://teambrazil.com$request_uri redirect; I then attempted to restart NGINX but got the same error message. My question is: is that a mistake, and is there anything more I have to do aside from restarting NGINX after making this change. As suggested by both tutorials I set up the directories: /etc/nginx/sites-enabled and /etc/nginx/sites-available and created the appropriate symbolic links using: touch /etc/nginx/sites-available/teambrazil.com ln -s /etc/nginx/sites-available/teambrazil.com /etc/nginx/sites-enabled/teambrazil.com Is there something else I need to consider after making this correction? Or was it not an error in the first place? I'm pretty stuck here. BTW, I am using Debian squeeze as an OS on Amerinoc's VPS. I'm just getting familiar with VPS administration and am pretty much a noob. Thanks very much, would appreciate any input.

  Read the article

• Installing mysqlnd for php 5.4.9 on CentOs 6.3

  - by kira423

  Okay let me get straight to the point, I am a complete noob, and have never done stuff like this at all, I have read tutorial after tuorial but I cant get anything to work. When I tried to install the rpm file I got this error rpm -Uvh ftp://ftp.pbone.net/mirror/rpms.famillecollet.com/enterprise/6/test/x86_64/php-mysqlnd-5.4.9-1.el6.remi.x86_64.rpm Retrieving ftp://ftp.pbone.net/mirror/rpms.famillecollet.com/enterprise/6/test/x86_64/php-mysqlnd-5.4.9-1.el6.remi.x86_64.rpm warning: /var/tmp/rpm-tmp.ez4vvd: Header V3 DSA/SHA1 Signature, key ID 00f97f56: NOKEY error: Failed dependencies: php-pdo(x86-64) = 5.4.9-1.el6.remi is needed by php-mysqlnd-5.4.9-1.el6.remi.x86_64 so I tried installing that rpm file and got this error rpm -ivh ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm Retrieving ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm curl: (9) Server denied you to change to the given directory error: skipping ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm - transfer failed I used the ftp links because I have no idea how else to get them to the server. I think I am getting overly frustrated with this, but I have to get this driver installed for any of my scripts to function correctly. Any help would be greatly appreciated!

  Read the article

• How do I Install Intermediate Certificates (in AWS)?

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

  Read the article

• EXCEL workbook, intermitently, takes 30 seconds to load

  - by Julio Nobre

  I am trying to figure out why a simple .XLS EXCEL workbook is taking, randomly, 30 seconds to open. Before answering: Please, bear mind the following: Problem symptoms Hanging is intermitent and it takes exactly 30 seconds; During hanging there is no cpu or disk activity; It only happens during workbook load. Every runs smooth after that; Windows Explorer.exe hangs on folder, but all other folders, system and applications are still responsive; There are no consecutive hangings. I have to wait for while to reproduce this behaviour; All workbooks where located on a local drive (C:\BPI); The workbook has no macros and no addins; Office 2003 is being used for several years; The computer is running Windows XP; Computer has several network mapped drives, all addressed to main file server; Recently, main fileserver was replaced by Windows 2011 SBS Standard Edition What I have done so far I have traced machine Explorer.exe, using Process Monitor, added Duration column, and filtered by Duration 1. That's is how I found that hanging was taking exactly 30 seconds. For further information, please refer to Oliver Salzburg tutorial. Using Process Monitor, I have also figured out than five operations were taking most of sample collecting duration. Looking at sample image below, column Operation below you will notice that one single operation was taking 29 seconds; I have tried different workbooks (all of them smaller than 30 KB); I have, temporarily, removed all shortcuts on User Document's folder that were pointing to network drives or shares; I have runned CCleaner to fix registry issues; I made sure that there were no external links on tested workbooks; I have reproduced this behaviour for hours; I have extensivelly researched for hours on the web; Process Monitor's collected and filtered data

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

• Solr startup script problem

  - by Camran

  I have installed solr and it works finally... I have now problems setting it up to start automatically with a start command. I have followed a tutorial and created a file called solr in the /etc/init.d/solr dir... Here is that file: #!/bin/sh -e # SOLR auto-start # # description: auto-starts solr engine # processname: solr-production # pidfile: /var/run/solr-production.pid NAME="solr" PIDFILE="/var/run/solr-production.pid" LOG_FILE="/var/log/solr-production.log" SOLR_DIR="/etc/jetty" JAVA_OPTIONS="-Xmx1024m -DSTOP.PORT=8079 -DSTOP.KEY=stopkey -jar start.jar" JAVA="/usr/bin/java" start() { echo -n "Starting $NAME... " if [ -f $PIDFILE ]; then echo "is already running!" else cd $SOLR_DIR $JAVA $JAVA_OPTIONS 2> $LOG_FILE & sleep 2 echo `ps -ef | grep -v grep | grep java | awk '{print $2}'` > $PIDFILE echo "(Done)" fi return 0 } stop() { echo -n "Stopping $NAME... " if [ -f $PIDFILE ]; then cd $SOLR_DIR $JAVA $JAVA_OPTIONS --stop sleep 2 rm $PIDFILE echo "(Done)" else echo "can not stop, it is not running!" fi return 0 } case "$1" in start) start ;; stop) stop ;; restart) stop sleep 5 start ;; *) echo "Usage: $0 (start | stop | restart)" exit 1 ;; esac Whenever I do solr -start I get this error: "Error occurred during initialization of VM Could not reserve enough space for object heap" I think this is because of the file above... Also here is where I have solr installed: var/www/solr and here is the start.jar file located: var/www/start.jar Help me out if you know whats causing this. Thanks BTW: OS is ubuntu 9.10

  Read the article

• Postfix SMTP-relay server against Gmail on CentOS 6.4

  - by Alex

  I'm currently trying to setup an SMTP-relay server to Gmail with Postfix on a CentOS 6.4 machine, so I can send e-mails from my PHP scripts. I followed this tutorial but I get this error output when trying to do a sendmail [email protected] Output: tail -f /var/log/maillog Apr 16 01:25:54 ext-server-dev01 postfix/cleanup[3646]: 86C2D3C05B0: message-id=<[email protected]> Apr 16 01:25:54 ext-server-dev01 postfix/qmgr[3643]: 86C2D3C05B0: from=<[email protected]>, size=297, nrcpt=1 (queue active) Apr 16 01:25:56 ext-server-dev01 postfix/smtp[3648]: 86C2D3C05B0: to=<[email protected]>, relay=smtp.gmail.com[173.194.79.108]:587, delay=4.8, delays=3.1/0.04/1.5/0.23, dsn=5.5.1, status=bounced (host smtp.gmail.com[173.194.79.108] said: 530-5.5.1 Authentication Required. Learn more at 530 5.5.1 http://support.google.com/mail/bin/answer.py?answer=14257 qh4sm3305629pac.8 - gsmtp (in reply to MAIL FROM command)) Here is my main.cf configuration, I tried a number of different options but nothing seems to work: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = ipv4 mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost myhostname = host.local.domain myorigin = $myhostname newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relayhost = [smtp.gmail.com]:587 sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_sasl_type = cyrus smtp_tls_CAfile = /etc/ssl/certs/ca-bundle.crt smtp_use_tls = yes smtpd_sasl_path = smtpd unknown_local_recipient_reject_code = 550 In the /etc/postfix/sasl_passwd files (sasl_passwd & sasl_passwd.db) I got the following (removed the real password, and replaced it with "password"): [smtp.google.com]:587 [email protected]:password To create the sasl_passwd.db file, I did that by running this command: postmap hash:/etc/postfix/sasl_passwd Do anybody got an idea why I can't seem to send an e-mail from the server? Kind Regards Alex

  Read the article

• Need a recommendation for shared storage on auto-scaling ec2 w/ scalr

  - by john h.

  I have come across so many answers to this question that I am completely lost! I am moving our 2 sites to a load balanced ec2 system with scalr as our cloud manager. Now the question is coming up about persistent storage for the user's uploaded content and other files. Could someone please give me a suggestion and possible a link to a tutorial for the following setup and goals. 2 websites (1 Forum, 1 ecommerce). 1 LB 1 App server (to scale out to as many as needed) 1 DB server (to scale out to as many as needed) Our sites will need to autoscale and according to what I am learning about scalr, that means as new instances load up, I need to run a script to set the basics up on that server (git,php mods, pull site from git, move keys, etc) What I don't understand is how should I handle user uploaded content like profile pictures, avatars, product images, themes, etc... Do I mount an EBS or s3fs folder to hold the websites (maybe /var/www/websitefolder) or do I do something like mount the avatar folders /var/www/websitefolder/images/avatars) I am not sure where to go with this. Could someone give me some detailed help? -John

  Read the article

• Adding custom service to nagiosgraph

  - by ravloony

  I have successfully added nagiosgraph to our nagios installation. I also added a memory checker plugin, from here : http://blog.vergiss-blackjack.de/2010/04/nagios-plugin-to-check-memory-consumption/. However I can't seem to get the graph of this service to be output by nagiosgraph. The plugin returns a single line like this: 31% (3785 of 11903 MB) used so i added a rule like this to the map file: /output:(\d+)% \((\d+) of (\d+) MB\) used/ and push @s, ['Mem', ['Percentage', 'GUAGE', $1], ['Used', 'GUAGE', $2], ['Total', 'GUAGE', $3] ]; I have also read this : http://www.mail-archive.com/[email protected]/msg36835.html and made sure that process_performance_data=1 in the nagios conf file. So far I have no graph for the Mem service on any host, and no rrd file either. I am unsure how to proceed to get this working. The documentation is rather difficult to follow and I haven't managed yet to understand it enough to do this. Can anyone point me to a tutorial, or some documentation which explains the steps needed to get a service noticed and graphed by nagiosgraph?

  Read the article

• Virtual host redirects to localhost in Ubuntu

  - by Salman

  I have recently configured Virtual Host in my Ubuntu 11.10. But whatever site i type, it always redirects to the localhost page. This is my "our-test-site" file: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/zftut/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/zftut/public/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> and this is my, "etc/hosts" file: 127.0.0.1 localhost 127.0.0.1 our-test-site.local 127.0.0.1 zftut.local 127.0.1.1 System.B System Now when I try to go for "zftut.local", it redirects me to localhost page, showing me this: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. What am I doing wrong? I refered "this" tutorial for setting up virtual host.

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• Service nginx reload: unexpected error

  - by Anna

  I'm trying to install wordpress on my nginx server by following this tutorial: http://premium.wpmudev.org/blog/how-to-setup-your-own-nginx-powered-wordpress-server/ However, the last command at step 7 gave me a strange error: service nginx reload A copy-paste from my terminal: root@server:~# service nginx reload Reloading nginx configuration: nginx: [emerg] unexpected "o" in /etc/nginx/sites-enabled/wordpress:7 nginx: configuration file /etc/nginx/nginx.conf test failed When I nano into sites-enabled/wordpress, on the 7th line I can't find anything strange: <!DOCTYPE html> <html class=" "> <head prefix="og: http://ogp.me/ns# fb: http://ogp.me/ns/fb# object: http://ogp.me/ns/object# article: http://ogp.me/ns/article# profile: http://ogp.me/ns/profile#"> <meta charset='utf-8'> <meta http-equiv="X-UA-Compatible" content="IE=edge"> Also, I don't see any obvious errors in my nginx.conf file, but maybe I'm not checking something? The first couple of lines of the nginx config file: user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } Any help is appreciated, thanks a lot in advance!

  Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >