Search Results

Search found 4065 results on 163 pages for 'intel mkl'.

Page 147/163 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

  • PC doesn't POST with a certain model of PSU

    - by Core Xii
    I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

    Read the article

  • after building in more ram, bios/debian does nothing [closed]

    - by derty
    My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

    Read the article

  • AA doesn't work due to monitor?

    - by MikeQ
    I have a monitor (with TV tuner - Philips 221T1SB), native resolution of 1920x1080, but there is an Overscan in Catalyst. It says from left to right '10%' and '0%', if i set it (all the way to the left) on 10%, i get screen with black borders (you know what i mean), but if i set it to 0%, i get a filled monitor. It does make sense, but why the hell is there such an option? I never had any AA issues before, but now, with this monitor, here they go. I can't find any solution, i have only one lead = overscan, or pretty much anything with the CCC settings. Yes, i almost forgot. After a bit of trying to configure the monitor with remote, i found there is a PC channel option, few other channels, and then a HDMI option. I have monitor through HDMI, but why i get black screen when i select the PC channel? That might be another problem. I tried almost everything. Please guys, give me a hand. I don't want jaggies! CPU: Intel I5-750 @4,0GHz RAM: Corsair Vengeance 8GB 1600MHz GPU: AMD Gigabyte HD 7950 Windforce @1100/1400, 1,174V Motherboard: ASUS P7P55D-E EVO

    Read the article

  • quad sli with gtx 690 not working

    - by Moaadh
    I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

    Read the article

  • 3-4 old computers = general purpose cluster?

    - by TheLQ
    I have 3 old computers lying around right now running a P2 at 800 MHz(?), Intel Mobile 1.6 GHz, AMD Athlon XP 2000+ at 1.66 GHz, and (might not use this) P4 at 2.7 GHz, all with 512 MB Ram, and am considering clustering them together for fun/knowledge. They would be running an undecided version of linux, preferably ubuntu based. The issue is what I want to use it for: general computing and occasional video encoding. By general computing I mean day to day tasks. However I'm not sure if every program started by a single X session is going to exist on the same machine, defeating the purpose of such a system. Will programs be split up or exist on one machine? Second, assuming this is running 100baseT ethernet (not sure if the PCI slot itself could handle Gigabit), would the speed of having a program exist over the network be an issue? It seems that the constant asking of various things in RAM would be quite slow. And before you say "buy another computer!", that's not the point of this question. I'm asking would it be usable, not necessarily practical. And yes I know, this is going to be extreamly power consuming.

    Read the article

  • Should I buy more RAM for my computer or a better CPU?

    - by Reijer The Coder
    I have recently bought a new laptop, an ASUS N56VJ-S4149H. I bought it to use it in all possible ways I could want, so that would be gaming downloading and streaming movies browsing the web and programming software. So far it has been running great but one thing annoys me a little bit. I frequently play Mount&Blade: Warband, it's a great game and you should check it out. Everything runs smoothly but only when I turn down the 'Texture Detail'. Otherwise it will lag a lot and I can't really play. Now my question is: Is this a problem of not enough RAM? At first I was really sure it was but after thinking about for a while I'm not anymore. My computer only has 4 Gigabytes of RAM and there is still a slot open. So will it improve when I buy another 8 Gigabytes? EDIT: It has an Nvidia GeForce GT 635M inside. and an Intel Core i5 3230M CPU with 2,6 GHz. Help and answers are really appreciated. Thanks to all.

    Read the article

  • Blue screen of Death on Install

    - by Toby Allen
    I have a machine with Windows Vista Installed. It has an Intel X25 SSD as the System Drive I want to reinstall (I plan to format and overwrite Vista) with XP. When I boot up using the Dell XP CD it loads the initial drivers then i get a Blue Screen. This is quite concerning. The installed OS works ok, but its giving problems so I want to remove it. Should I just format the SSD and try again? Will this make any difference? Can I do something to avoid hitting the Blue Screen? Its possible I had corrupt sectors on one of the other disks, will a new XP install use the System drive or drive 0? Can I force the install to use a specific drive when installing? Error: *** STOP: 0x0000007B (0xF78D2524,0x0000034,0x00000000,0x00000000) I never did find the answer, however I removed the SSD and tried to install on other disk - CRASH I disconnected the other disk and tried to install with only SSD plugged in - CRASH I removed 1 block of RAM - CRASH I used a windows 7 CD - NO CRASH

    Read the article

  • Windows 7 not booting after failed SRT (SSD caching) install

    - by david
    This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

    Read the article

  • USB 3.0 ports backwards compatibility problems with 2.0 devices?

    - by AaronLS
    I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

    Read the article

  • Can't access YouTube

    - by Agentleader1
    I can not seem to connect to YouTube at all. If I connect directly to YouTube (youtube.com) I get this: And if I try to connect via video directly (youtube.com/watch?v=), I get this: Here's how this isn't a web issue: I have malware on my computer I believe. And the question here is, how do I get rid of it, or what possible issue could this be? I can verify this is not a website issue or wifi issue, I've tried to connect on another computer in my wifi, and it worked. It is the local machine issue. I've tried to get rid of malware at my best and also have tried to disable possible virus extensions. All can out as the same result: no help. Also, I am unable to find these hiding viruses. I used malware-bytes and Microsoft Security Essentials. Edit: This is OBVIOUSLY Windows. I am currently running on a laptop Windows 7 Home Premium 4gb ram 64-bit os Lifebook series manufactured by Fujitsu America, Inc. Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz nslookup youtube.com:

    Read the article

  • less maximum buffer size?

    - by Tyzoid
    I was messing around with my system and found a novel way to use up memory, but it seems that the less command only holds a limited amount of data before stopping/killing the command. To test, run (careful! uses lots of system memory very fast!) $ cat /dev/zero | less From my testing, it looks like the command is killed after less reaches 2.5 gigabytes of memory, but I can't find anything in the man page that suggests that it would limit it in such a way. In addition, I couldn't find any documentation via the google on the subject. Any light to this quite surprising discovery would be great! System Information: Quad core intel i7, 8gb ram. $ uname -a Linux Tyler-Work 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux $ less --version less 458 (GNU regular expressions) Copyright (C) 1984-2012 Mark Nudelman less comes with NO WARRANTY, to the extent permitted by law. For information about the terms of redistribution, see the file named README in the less distribution. Homepage: http://www.greenwoodsoftware.com/less $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty

    Read the article

  • How should I configure backup of my server?

    - by ed209
    I have just rented a dedicated server. If it helps this is the config I have: CPU1 Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (Cores 8) RAM 15975 MB Disk /dev/sda doesn't contain a valid partition table (=> /dev/sda doesn't) Disk /dev/sdc doesn't contain a valid partition table (=> /dev/sdc doesn't) Disk /dev/sdb doesn't contain a valid partition table (=> /dev/sdb doesn't) Disk /dev/sda: 120.0 GB (=> 114 GIB) Disk /dev/sdc: 3000.6 GB (=> 2861 GIB) Disk /dev/sdb: 3000.6 GB (=> 2861 GIB) /dev/sda is a 120GB SSD. This is where I have Ubuntu/lamp installed. It's the drive that will run my site. With the account I got two other drives of 3000GB each which I really don't need but they came with the account. I figured I could use these to back up my main 120gb drive. So a couple of things I wondered were: Should I use these for backups? How should I back up. The data I want to back up is a user uploads directory full of images and the database. Everything else is either in a code repo or backed up some other way. For example, it would be nice to know there is a disk image of the 120gb drive somewhere that I can copy over should there be any problems but equally I don't mind doing a fresh install of all the software and copying over just the images and database dump. Thanks for your advice! (also, happy to not use the two other drives and backup elsewhere if it's more sensible)

    Read the article

  • Installed Memory (RAM): 8GB (4GB Useable)

    - by Mike Bannister
    I have 4X 2GB RAM sticks installed, Windows 7 Ultimate x64 shows "Installed Memory (RAM): 8GB (4GB Useable)" in the system information. The motherboard says it supports up to 16GB of memory. I had Windows XP x64 and I'm pretty sure it was able to use all 8Gigs of memory. I've just formatted and am not burning through 4GB for sure. *The BIOS only show 4096MB while booting. I was only able to find one option relating to memory mapping and it took it from 4Gigs to 3 and change. CPU-Z shows all 4 sticks as 2048MB I went in to msconfig and checked the limits, they are not set. I tried resetting the CPU and RAM sticks 3 times, the CPU has no pins to be bent (flat contacts, I5) I rearranged all the RAM. I have separate video memory from the system memory. I have a 64 bit OS (I am 100% certain) Hardware: Memory: Four Corsair XMS3 TW3X4G1333C9AG Motherboard: Asus P7P55D Pro CPU: Intel Core i5-760 BX80605I5760 Graphics: Two ZOTAC ZT-50401-10L GeForce GTX 550 Ti If anyone has new ideas or knows the exact setting in the bios, it would be greatly appreciated.

    Read the article

  • Windows 7: Dual Monitor Issue

    - by sdoca
    I have a Dell laptop with a docking station and two external monitors hooked up. I'm running Windows 7 64 bit. Originally, the two monitors were the same - Dell 1908FP. I have replaced one of them with an HP LA2405. I have set the HP 24" (1920 x 1200 connected via DVI port) as montior 1 and extended to use the Dell 19" (12080 x 1024 connected via VGA port) as monitor 2. I have set my power plan so that when the laptop is plugged in, it will turn the monitors off after 10 minutes, but it will not put my laptop to sleep. However, now that I have the HP monitor, when I unlock my laptop and the monitors come back on, all my windows are resized and shifted to the top left corner of the HP monitor as if they had been resized for display on the smaller Dell monitor. A co-worker has the exact same laptop and monitor configuration but doesn't experience this issue, so I figure there's some configuration that's different but we can't find it. I haven't been able to find any mention of a similar problem doing an internet search, but I'm not really sure what terms to use in my search. Anybody have any suggestions as to what may be causing the issue? OS setting? Monitor setting? EDIT: My laptop is using the Intel Graphics and Media Control Panel/drivers.

    Read the article

  • Why am I getting programs stuck in log_wait_commit under Linux?

    - by staticsan
    There is something subtly wrong with my Linux install that I just can't locate. It is Ubuntu Lucid Lynx (10.04) 64-bit. Hardware is a Dell Optiplex 960: Intel Core 2 Quad CPU, 8Gb of RAM, 2x 300Gb HDDs. /home is ext2 on one disk and everything else is on the other (/ is also ext3). I have VirtualBox running a 64-bit Vista image for Outlook calendaring, but the heavyweight apps are IntelliJ, NetBeans, MySQL and Opera. Opera also loads my mail (IMAP) of which there is over 10,000 messages. The problem is that Opera stalls for a few seconds from time-to-time. Watching the process list shows it's in log_wait_commit which means (as far as I have figured out) the filesystem is holding things up. Sometimes I can make this happen by doing a subversion update, but usually it happens for no reason I can see. It usually happens to Opera, but I've seen NetBeans go under, too. It doesn't make the app crash - it's just completely unresponsive for a few seconds. Googling has not helped. The closest I got was to remove the sync attribute in the file system. This achieved nothing. On the advice of a Linux guru friend, I lowered /proc/sys/vm/dirty_writeback_centisecs to 300, but that didn't do anything, either. And it was all he could think of. What is going on and can I fix it? (And how?)

    Read the article

  • LMDE detects a wireless card, but can't use it

    - by Davidos
    LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

    Read the article

  • Can't get 1440x900 resolution with GRUB2 although vbeinfo says it's available

    - by TomSW
    I'm trying to use GRUB2 in graphical mode with 1440x900 resolution, but the result is always garbled nonsense: the highest resolution I can get is 1280x800. Word is from googling that long as vbeinfo lists a resolution, GRUB2 can use it. This doesn't seem to be true: vbeinfo says that 1440x900 is available but it doesn't work. Testing it from the GRUB2 command line: set gxfmode=1440x900 terminal_output gfxterm # -> garbled nonsense # back to trusty 640x480 terminal_output console The graphics card is an Intel GM965. Once linux boots the framebuffer switches to 1440x900. Added after epheminent's reply and various experiments vbeinfo lists two sets of modes. The first set runs from 0x160 to 0x16b, with resolutions 768x480, 960x600, 1280x800 and 1440x900 Then - after a bunch of text-only modes - the second set, containing resolutions 1024x768, 800x600, and 640x480 The first set of modes aren't altered by 915resolution. They all work except 1440x900. The resolution of modes in the second set can be altered using the 915resolution module / command available in GRUB2 = 1.99. # in /boot/grub/grub.cfg insmod 915resolution # 30, 32, 34 all work for me: all that varies is which modes are altered 915resolution 30 1440 900 # setting an impossible resolution changes the mode to "text-only" # in my case 1280x1024 is not supported 915resolution 30 1280 1024 Clearly, 1440x900 should just work: adding it with 915resolution is just a workaround.

    Read the article

  • Computer is dying--what should I be looking for?

    - by Will
    Okay, I'm a bit knowledgeable with pooters and such, but i'm confused. My computer is dying slowly, and I'm not sure what part is causing this. Computer details: Vista, dell machine, intel Q6600, 2.4 Core Duo (quad core), standard memory and drive (unknown manufacturer). Symptoms: I would best describe the symptoms as memory corruption. After a couple days on, I start getting applications crashing or failing to open for a lack of "resources". Sounds are corrupted. Onscreen text gets corrupted; the characters of text are garbled, not the pixels on the screen. Video memory seems untouched as I haven't seen any misplaced pixels. Recently I've lost files on disk. I've also experienced errors reporting a supposed lack of disk space, even though I have fifty gigs free. There was one point where I couldn't get to the POST when booting up. After I cleaned everything (see next) this hasn't happened. Diagnostic steps: First thing I did was clean the case. There was a lot of dust buildup on heatsinks, so I cleaned all that up. No help. Next, I disconnected and reconnected everything, from power cables to memory (did not reseat cpu). No change. Last, I ran the standard vista memory diagnostics and ran checkdisk. Both reported no errors found. I have not run any POST tests, now that I think about it. I'm at a loss at this point. Disk appears fine, memory too. I'd expect motherboard issues to result in the thing not booting up, yet it does every time. What should I be looking at? What more can I do?

    Read the article

  • Server taking too long to respond error

    - by DCJones
    Hi, This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0

    Read the article

  • How to fix Windows 7 device removal notification loop

    - by Barry Kelly
    Bit of an odd one this. One of our PCs is getting caught in a loop some time after being turned on, usually after a USB storage device has been attached - sometimes an iPod, sometimes a GPS. Specifically, Windows Explorer starts showing a drive icon and letter (E:, as of right now) for the System partition (the small hidden one at the start of the boot drive). Then, the icon disappears. Then it reappears again. And disappears. It does this very quickly, at what looks like maybe 50 times a second. CPU usage in this loop is also very high; averages about 66%. This machine has an i7 920 CPU, which is quad core with hyperthreading; so this usage rate works out to about 5 100% busy threads, along with whatever normal idle load is (particularly Task Manager itself). Inspecting with Process Explorer shows that the device removal notification infrastructure has gone berserk. The threads in system service processes (i.e. apart from Windows Explorer) which are using all the CPU power relate to device notification. The Disk Management MMC snap-in also fails to run when the loop starts. The only way to break the loop, it seems, is to reboot the machine. Anyone seen anything similar to this, and know of a way to fix it? Machine details: Windows 7 x64, fully patched i7 920, 12GB RAM Intel SSD 80GB (X25-M, I believe; not G2) 2TB 5.2K disk for bulk storage AMD HD 5870 Further hardware details await. I'm going to go through and update all drivers I can find.

    Read the article

  • Fedora Core 6 Migration

    - by Matthew Sprankle
    I am at a loss as to what I should to for this server. I need it to run php5.3 and corresponding version of mysql. I received a client today through work that is using Fedora core 6 running 10 very small websites on some very hodge podge setup. My original idea was just upgrade to php5.3. I have yum (installed 3.0.8) reconfigured for the fedora archive. The latest version of php it allows is 5.1.8. I am still relatively new to server setups and am nervous about wiping their server to upgrade it. Since it is about 6-8 years old I'm not sure if it will even support the newest version of fedora. The server specs are: Parallels Plesk Panel version 9.5.4 Operating system Linux 2.6.9-023stab048.4-smp CPU GenuineIntel, Intel(R) Xeon(R)CPU E5335 @ 2.00GHz (10gb disk space and 1gb of memory). I use fedora for my personal server so I was a little familiar with it. I haven't done anything too extravagant. Is there a way I can escape this nightmare with installing php5.3 or do I need to migrate these sites to a new server?

    Read the article

  • How to set up multiple video cards in Windows XP

    - by Swish
    All I am trying to do is run a three monitor setup, two widescreens on the good card at high res and a third smaller monitor at 1024x768 that I watch continuously updating info in. I have a Dell Vostro 200 with an HIS Radeon HD 4670 video card in the PCI-e slot. I need an additional video card that will work in an available PCI slot. I Had a Nvidia GeForce 5200 that was installed but due to what I'm assuming was a compatible driver issue (because it was Nvidia not ATI) it wouldn't run at more than 640x480 4bit color when installed simultaneously with the HIS card. Previously I used the Nvidia with the onboard Intel video to run a third monitor, but now that the HSI uses PCI-e the onboard has to be disabled. I tried a Radeon 9200 PCI card that I found (microsoft made I think) with it and only that or the HIS card could be enabled at the same time. When both were in the HIS card said "The device cannot start". SO, based on the fact that I got the Nvidia to work (although very poorly) with the new HIS Radeon HD 4670 PCI-e I know it's possible, just don't know what type of card I need to use. Any ideas?

    Read the article

  • Nvidia GTX 660m crashes games

    - by dcap
    I just recently bought a Lenovo y580 with both HD intel graphics and an Nvidia GTX 660m. It works great except for one thing: playing games. Every time I load a game, either with Steam or Games for Windows Live, games will end up crashing. I've already talked with lenovo tech support and they couldn't help other than send my new laptop for repair which would take 7 days. So before I do that I thought I'd ask around. These are the games I've tested and what happens when they load: Civilization V: Game loads fine but once it gets loaded to the game, there's noticeable "tearing" popping up and certain things flash. Within a minute of this, the game crashes. Does the same thing regardless if Vsync is on or off. Total War Shogun2: Game gets to the menu screen. The background of the menu screen shows what is expected - slideshow of in-game environments rendered on high settings (this is expected). However, within 2 seconds of the menu loading up it crashes. Age of Empires 3 (Non-steam): This game is several years old so it should work on this brand new laptop fine. However the results are similar to that of Civilization V. Noticeable "Tearing" and after a few seconds it'll freeze/crash. I've done tests on all these games with both the latest stable Nvidia driver 285 as well as the nightly build 307. In addition, Nvidia control panel is set on using the dedicated graphics card for all programs. So is there anything I can do to fix this or will I have to send it back for a week to tech support?

    Read the article

  • Low 'Burst Rate' from SATA drive in HDTune?

    - by UpTheCreek
    I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

    Read the article

  • Server specification recommendation

    - by foo
    To cut the story short, I can't buy an item (server/cpu/motherboard/ram) that costs more than USD 330. However, I can combine them, meaning, I can buy a CPU that costs USD 330 and motherboard that costs USD 330. With this limitation, I can't buy a powerful 1U server which will definitely costs me more USD 330. With that in mind, I was hoping to build a powerful desktop PC which will be used as a database server. However, through my experience, desktop PC doesn't last very long, usually the motherboard will just die by itself after 1 or 2 years. So, what would you guys recommend me to buy with this kind of budget? Every item must be <= USD 330. Will be used as a MySQL server. RAID would be nice. 1TB is pretty big for my data. I do not need external graphic card (onboard would do just fine), mouse, keyboard, monitor. Linux friendly. One ethernet port is good enough. It's important that those hardware is made of components that will last long (at least 3 years or something). The server will be placed in an air conditioned room, but a good ventilation for the server is always preferred. I won't overclock it. Intel processor is preferred. Thanks in advance.

    Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >