Search Results

Search found 6065 results on 243 pages for 'usb modeswitch'.

Page 147/243 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

• how do i fix this: the networking and wireless are enabled. but list of networks under wireless networks not available

  - by Ayesha Ahmad

  i started working with ubuntu 11.10 last year. i upgraded to 12.04 a week back. since then i have had all sorts of problems with network connection. first had to install the new driver. the hardware switch somehow got disabled then the above problem arrived. even tho the options are all enabled, the OS is not able to detect scan available network connections. also i have to bring to notice that once in a while it does get connected, can not explain how it happens. I want to fix this problem once and for all. please help. ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:51:b3:c8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:44 eth1 Link encap:Ethernet HWaddr 1c:65:9d:67:d5:e1 inet6 addr: fe80::1e65:9dff:fe67:d5e1/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:170 TX packets:0 errors:27 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:344 errors:0 dropped:0 overruns:0 frame:0 TX packets:344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20336 (20.3 KB) TX bytes:20336 (20.3 KB) lshw -c network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 1c:65:9d:67:d5:e1 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: f0:4d:a2:51:b3:c8 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:196 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) I hope this information is of some help.

  Read the article

• mythbuntu 12 - lirc device doesn't appear to even exist

  - by FrustratedWithFormsDesigner

  I'm trying to get a new installation of Mythbuntu working. So far, everything is OK except the remote. The sensor for the remote is on my Hauppauge WinTV HVR 1250. First I tried to run irw to see what was being picked up by the sensor: $ irw connect: No such file or directory Then trying to run lircd gives: $ lircd start$ lircd start lircd: can't open or create /var/run/lirc/lircd.pid I look for any lirc devices and find there are none: $ ls /dev/li* ls: cannot access /dev/li*: No such file or directory Just to be sure, I check in /proc/bus/input/devices, which shows me two powerbuttons (not sure why), kbd and mouse dev, and the audio devs. Nothing for the IR receiver on the tuner card (which I thought was strange because shouldn't the tuner show up here?). $ cat /proc/bus/input/devices I: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=PNP0C0C/button/input0 S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 U: Uniq= H: Handlers=kbd event0 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=LNXPWRBN/button/input0 S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 U: Uniq= H: Handlers=kbd event1 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0003 Vendor=099a Product=7202 Version=0111 N: Name="Wireless Keyboard/Mouse" P: Phys=usb-0000:00:10.1-2/input0 S: Sysfs=/devices/pci0000:00/0000:00:10.1/usb8/8-2/8-2:1.0/input/input2 U: Uniq= H: Handlers=sysrq kbd event2 B: PROP=0 B: EV=120013 B: KEY=1000000000007 ff9f207ac14057ff febeffdfffefffff fffffffffffffffe B: MSC=10 B: LED=7 I: Bus=0003 Vendor=099a Product=7202 Version=0111 N: Name="Wireless Keyboard/Mouse" P: Phys=usb-0000:00:10.1-2/input1 S: Sysfs=/devices/pci0000:00/0000:00:10.1/usb8/8-2/8-2:1.1/input/input3 U: Uniq= H: Handlers=kbd mouse0 event3 B: PROP=0 B: EV=1f B: KEY=4837fff072ff32d bf54444600000000 70001 20c100b17c000 267bfad9415fed 9e168000004400 10000002 B: REL=143 B: ABS=100000000 B: MSC=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Line" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input4 U: Uniq= H: Handlers=event4 B: PROP=0 B: EV=21 B: SW=2000 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Front Mic" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input5 U: Uniq= H: Handlers=event5 B: PROP=0 B: EV=21 B: SW=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Rear Mic" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input6 U: Uniq= H: Handlers=event6 B: PROP=0 B: EV=21 B: SW=10 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Front Headphone" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input7 U: Uniq= H: Handlers=event7 B: PROP=0 B: EV=21 B: SW=4 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="HD-Audio Generic Line-Out" P: Phys=ALSA S: Sysfs=/devices/pci0000:00/0000:00:14.2/sound/card0/input8 U: Uniq= H: Handlers=event8 B: PROP=0 B: EV=21 B: SW=40 According to dmesg, the driver was registered, but it doesn't look like any devices was associated with the driver: $ dmesg | grep irc [ 10.631162] lirc_dev: IR Remote Control driver registered, major 249 So far, I've seen a number of forum pages suggesting that I use some trick to create a link between /dev/lirc and some other device that is the REAL IR sensor, like /dev/event5, but those cases assume that the real device is shown from /proc/bus/input/devices, and I don't see any such device there. Any suggestions on how to fix or further diagnose this?

  Read the article

• Is this simple XOR encrypted communication absolutely secure?

  - by user3123061

  Say Alice have 4GB USB flash memory and Peter also have 4GB USB flash memory. They once meet and save on both of memories two files named alice_to_peter.key (2GB) and peter_to_alice.key (2GB) which is randomly generated bits. Then they never meet again and communicate electronicaly. Alice also maintains variable called alice_pointer and Peter maintains variable called peter_pointer which is both initially set to zero. Then when Alice needs to send message to Peter they do: encrypted_message_to_peter[n] = message_to_peter[n] XOR alice_to_peter.key[alice_pointer + n] Where n i n-th byte of message. Then alice_pointer is attached at begining of the encrypted message and (alice_pointer + encrypted message) is sent to Peter and then alice_pointer is incremented by length of message (and for maximum security can be used part of key erased) Peter receives encrypted_message, reads alice_pointer stored at beginning of message and do this: message_to_peter[n] = encrypted_message_to_peter[n] XOR alice_to_peter.key[alice_pointer + n] And for maximum security after reading of message also erases used part of key. - EDIT: In fact this step with this simple algorithm (without integrity check and authentication) decreases security, see Paulo Ebermann post below. When Peter needs to send message to Alice they do analogical steps with peter_to_alice.key and with peter_pointer. With this trivial schema they can send for next 50 years each day 2GB / (50 * 365) = cca 115kB of encrypted data in both directions. If they need more data to send, they simple use larger memory for keys for example with today 2TB harddiscs (1TB keys) is possible to exchange next 50years 60MB/day ! (thats practicaly lots of data for example with using compression its more than hour of high quality voice communication) It Seems to me there is no way for attacker to read encrypted message without keys even if they have infinitely fast computer. because even with infinitely fast computer with brute force they get ever possible message that can fit to length of message, but this is astronomical amount of messages and attacker dont know which of them is actual message. I am right? Is this communication schema really absolutely secure? And if its secure, has this communication method its own name? (I mean XOR encryption is well-known, but whats name of this concrete practical application with use large memories at both communication sides for keys? I am humbly expecting that this application has been invented someone before me :-) ) Note: If its absolutely secure then its amazing because with today low cost large memories it is practicaly much cheeper way of secure communication than expensive quantum cryptography and with equivalent security! EDIT: I think it will be more and more practical in future with lower a lower cost of memories. It can solve secure communication forever. Today you have no certainty if someone succesfuly atack to existing ciphers one year later and make its often expensive implementations unsecure. In many cases before comunication exist step where communicating sides meets personaly, thats time to generate large keys. I think its perfect for military communication for example for communication with submarines which can have installed harddrive with large keys and military central can have harddrive for each submarine they have. It can be also practical in everyday life for example for control your bank account because when you create your account you meet with bank etc.

  Read the article

• Automount of external hard disk

  - by moose

  I have an Intenso 6002560 1TB Memory Station - an external hard disk. This hard disk gets connected via Y-USB cable. When I connect both USB-ends to my Notebook, it gets recognized by my Ubuntu 10.04.4 LTS system: moose@pc07:~$ lsusb [...] Bus 002 Device 005: ID 13fd:1840 Initio Corporation [...] and Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065e10 Device Boot Start End Blocks Id System /dev/sda1 * 1 37810 303704064 83 Linux /dev/sda2 37810 38914 8864769 5 Extended /dev/sda5 37810 38914 8864768 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0d6ea32a Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976759008+ c W95 FAT32 (LBA) But it did not get mounted: moose@pc07:/dev$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) However, I could mount it manually with mount -t vfat /dev/sdc1 /mnt/sdc1 as you can see here: moose@pc07:~$ mount -l /dev/sda1 on / type ext4 (rw,errors=remount-ro,user_xattr) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/moose/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=moose) /dev/sdc1 on /mnt/sdc1 type vfat (rw) edit: Another command: moose@pc07:~$ sudo blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 moose@pc07:~$ blkid -o list device fs_type label mount point UUID ---------------------------------------------------------------------------------------------------------------------- /dev/sda1 ext4 / 45eb611b-517e-425b-8057-0391726cccd5 /dev/sda5 swap <swap> e9dc42f3-594c-4b62-874a-305eda5eed41 /dev/sdc1 /mnt/sdc1 edit: another command: moose@pc07:~$ ls -l /dev/disk/by-uuid/ total 0 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 45eb611b-517e-425b-8057-0391726cccd5 -> ../../sda1 lrwxrwxrwx 1 root root 10 2012-09-30 09:31 e9dc42f3-594c-4b62-874a-305eda5eed41 -> ../../sda5 Here is a link to a Launchpad question about this problem. But I would like it to mount automatically. What do I have to do?

  Read the article

• LSI SAS 9240-8i on Ubuntu 12.04 Hangs on Modprobe

  - by Francois Stark

  I used the LSI 9240-8i card on a smaller Intel motherboard with no problems in Ubuntu, with ZFS. However, we rebuilt the server to allow for more disks, using the ASROCK X79 Extreme 11 motherboard. It has 7 PCIe slots, and a LSI 2008 on-board. At first I thought the LSI 9240, when plugged in to PCIe, clashed with the on-board LSI 2008. Every time I plugged in the LSI 9240, modprobe would hang. Then I completely disabled the on-board LSI 2008, and the problem persisted. Last night it booted perfectly ONCE - all LSI cards and connected disks visible... However, all subsequent reboots failed. Both LSI cards' bios scans appear and they both see the disks connected to them, but Ubuntu modprobe hangs. Some selected dmesg lines, with both LSI cards enabled: [ 190.752100] megasas: [ 0]waiting for 1 commands to complete [ 195.772071] megasas: [ 5]waiting for 1 commands to complete [ 200.792079] megasas: [10]waiting for 1 commands to complete [ 205.812078] megasas: [15]waiting for 1 commands to complete [ 210.832037] megasas: [20]waiting for 1 commands to complete [ 215.852077] megasas: [25]waiting for 1 commands to complete [ 220.872072] megasas: [30]waiting for 1 commands to complete [ 225.892078] megasas: [35]waiting for 1 commands to complete [ 230.912086] megasas: [40]waiting for 1 commands to complete [ 235.932075] megasas: [45]waiting for 1 commands to complete [ 240.306157] usb 2-1.5: USB disconnect, device number 7 [ 240.952076] megasas: [50]waiting for 1 commands to complete [ 240.960034] INFO: task modprobe:233 blocked for more than 120 seconds. [ 240.960055] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.960067] modprobe D ffffffff81806200 0 233 146 0x00000004 [ 240.960075] ffff880806ae3b48 0000000000000086 ffff880806ae3ae8 ffffffff8101adf3 [ 240.960083] ffff880806ae3fd8 ffff880806ae3fd8 ffff880806ae3fd8 0000000000013780 [ 240.960090] ffffffff81c0d020 ffff880806acae00 ffff880806ae3b58 ffff880808961720 [ 240.960096] Call Trace: [ 240.960107] [<ffffffff8101adf3>] ? native_sched_clock+0x13/0x80 [ 240.960116] [<ffffffff816579cf>] schedule+0x3f/0x60 [ 240.960137] [<ffffffffa00093f5>] megasas_issue_blocked_cmd+0x75/0xb0 [megaraid_sas] [ 240.960144] [<ffffffff8108aa50>] ? add_wait_queue+0x60/0x60 [ 240.960154] [<ffffffffa000a6c9>] megasas_get_seq_num+0xd9/0x260 [megaraid_sas] [ 240.960164] [<ffffffffa000ab31>] megasas_start_aen+0x31/0x60 [megaraid_sas] [ 240.960174] [<ffffffffa00136f1>] megasas_probe_one+0x69a/0x81c [megaraid_sas] [ 240.960182] [<ffffffff813345bc>] local_pci_probe+0x5c/0xd0 [ 240.960189] [<ffffffff81335e89>] __pci_device_probe+0xf9/0x100 [ 240.960197] [<ffffffff8130ce6a>] ? kobject_get+0x1a/0x30 [ 240.960205] [<ffffffff81335eca>] pci_device_probe+0x3a/0x60 [ 240.960212] [<ffffffff813f5278>] really_probe+0x68/0x190 [ 240.960217] [<ffffffff813f5505>] driver_probe_device+0x45/0x70 [ 240.960223] [<ffffffff813f55db>] __driver_attach+0xab/0xb0 [ 240.960227] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960233] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960237] [<ffffffff813f436c>] bus_for_each_dev+0x5c/0x90 [ 240.960243] [<ffffffff813f503e>] driver_attach+0x1e/0x20 [ 240.960248] [<ffffffff813f4c90>] bus_add_driver+0x1a0/0x270 [ 240.960255] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960260] [<ffffffff813f5b46>] driver_register+0x76/0x140 [ 240.960266] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960271] [<ffffffff81335b66>] __pci_register_driver+0x56/0xd0 [ 240.960277] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960286] [<ffffffffa001e09e>] megasas_init+0x9e/0x1000 [megaraid_sas] [ 240.960294] [<ffffffff81002040>] do_one_initcall+0x40/0x180 [ 240.960301] [<ffffffff810a82fe>] sys_init_module+0xbe/0x230 [ 240.960307] [<ffffffff81661ec2>] system_call_fastpath+0x16/0x1b [ 240.960314] INFO: task scsi_scan_7:349 blocked for more than 120 seconds.

  Read the article

• UEFI Dual-Boot - Ubuntu 12.04.3 + Windows 8.1 (One GPT HDD)

  - by swafbrother

  UEFI Dual-Boot - Ubuntu 12.04.3 + Windows 8.1 (One GPT HDD) Hello, I'm having trouble setting up a dual-boot (Ubuntu 12.04 LTS and Windows 8.1) in my ASUS K55VM laptop's hard drive disk (500 GB). I was mostly following tutorials for doing this, but at some point something has gone wrong. Up to now, I have followed these steps: I formatted my HDD into GPT. I clean-installed Windows 8.1. I didn't prevent Windows from choosing the partitions to use and it created these partitions: A Recovery partition (sda1). An EFI System Partition (sda2). A Microsoft Reserved Partition (sda3). A Windows Data Partition or C drive (sda4). I reduced the Windows Data Partition via Windows' Disk Management. I made a bootable USB Stick with Ubuntu 12.04 LTS from ISO, using Universal USB Installer. I created these partitions for Ubuntu: A Boot partition, mounted at /boot (sda5). A Root partition, mounted at / (sda6). A Swap partition (sda7). In Device for boot loader installation I chose: /dev/sda. Then, when I rebooted, it went straight into Ubuntu. So I installed Boot-Repair, and clicked on Recommended Repair. It automatically did its job without asking for anything. I rebooted and Grub showed up, with a lot of options. At this point I had a decent dual-boot setup; Ubuntu and both Windows entries worked fine: Ubuntu. Windows Boot UEFI Loader. Windows UEFI bkpbootmgfw.efi. I executed this command: sudo grub-install --force /dev/sda5. Then I tried to make Windows 8.1's Boot Manager the main boot manager, so that I could choose which OS to boot into from a menu. I downloaded EasyBCD on Windows. It showed 2 Ubuntu entries and 1 Windows entry. I went into BCD Deployment tab and clicked on Write MBR. At this point, I went into BIOS and made Windows Boot Manager the first boot option. When I rebooted, I got a black screen with the message efidisk read error, and then (I guess) it switched to the next boot option, which is Ubuntu, resulting in Grub showing up. From Grub, Ubuntu entry is working and so are both Windows entries. If I choose Ubuntu, it normally boots into Ubuntu. But if I choose Windows, it goes into Windows' boot manager. In Windows' boot manager, a menu shows up: Ubuntu. Ubuntu. Windows 8.1. If I choose Windows, it boots into Windows without any problem. If I choose Ubuntu, it boots into Grub (back to step 14). Here's my BootInfo Summary: http://paste.ubuntu.com/6698171/ Windows Boot Manager is clearly not working as expected; I can't directly boot into it and I can't boot into it from BIOS either (efidisk read error again). If I want to boot into Windows I need to boot into Grub first, which is the opposite of what I wanted. I need help at this point. What is the best thing I can do? Is there a more reliable and/or simpler way of acomplishing a satisfying dual-boot for this situation? Can someone provide a way for going back to step 8, where I had a more efficient dual-boot setup? If only I could undo what I did with Easy BCD and skip Windows' Boot Menu... Can someone provide a way to fix this mess? Thanks in advance and sorry for the length of this, I wanted to be exhaustive.

  Read the article

• Tweaking Remote Control (In-Kernel LIRC)

  - by Geoff

  I've recently rebuilt my MythTV box using Mythbuntu 12.04, to take advantage of newer hardware (Ivy Bridge). On my previous build I used lirc to manage the remote, i.e. the mapping of key codes - keypresses - application keys; it was quite a journey to learn it all, and I ended up fairly comfortable with how it all worked. What I have: I have a cheap Chinavasion remote and USB dongle, which I've found several articles on; these largely revolve around working with XBMC (interesting, but I don't think directly applicable) and also around getting a Harmony remote to work (it's a Chinavasion CVSB-983 - very useful, since I needed this to get my Harmony 900 working). Mythbuntu 12.04 64-bit MythTV 0.25 (likely irrelevant) How it is right now When I plug this in, it 'just works'. Which is great, except that Ubuntu uses it natively, and prevents some of the button presses from getting through to Myth. For example, I can send a button from the remote that equates to Ctrl-Alt-A (which I assume Ubuntu isn't interested in), and then trap that in Mythfrontend, but the remote's Play button is caught by Ubuntu (which displays a large circle with a line though it, as there's no media player loaded). I understand that this is because lirc is merged into the kernel now, and I like that. What I've done so far: Found the device using lsusb: $ lsusb Bus 001 Device 004: ID 073a:2230 Chaplet Systems, Inc. infrared dongle for remote Found the event device number: $ cat /proc/bus/input/devices I: Bus=0003 Vendor=073a Product=2230 Version=0110 N: Name="HID 073a:2230" P: Phys=usb-0000:00:1a.0-1.2/input0 S: Sysfs=/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input5 U: Uniq= H: Handlers=sysrq kbd mouse1 event5 js0 B: PROP=0 B: EV=10001f B: KEY=4c37fff072ff32d bf54445600000000 ffffffffff 30c100b17c007 ffa67bfad951dfff febeffdfffefffff fffffffffffffffe B: REL=343 B: ABS=100030000 B: MSC=10 Tested the input with evtest (I pressed Play): $ sudo evtest /dev/input/event5 Input driver version is 1.0.1 Input device ID: bus 0x3 vendor 0x73a product 0x2230 version 0x110 Input device name: "HID 073a:2230" Supported events: Event type 0 (EV_SYN) Event type 1 (EV_KEY) Event code 1 (KEY_ESC) Event code 2 (KEY_1) Event code 3 (KEY_2) Event code 4 (KEY_3) Event code 5 (KEY_4) Event code 6 (KEY_5) Event code 7 (KEY_6) <------------snipped lots of 'Event code' lines------------> Testing ... (interrupt to exit) Event: time 1336435683.230656, -------------- SYN_REPORT ------------ Event: time 1336435683.246648, type 4 (EV_MSC), code 4 (MSC_SCAN), value c00cd Event: time 1336435683.246652, type 1 (EV_KEY), code 164 (KEY_PLAYPAUSE), value 0 Event: time 1336435683.246655, -------------- SYN_REPORT ------------ Tested showkey, again for the Play key: $ sudo showkey -s kb mode was RAW [ if you are trying this under X, it might not work since the X server is also reading /dev/console ] press any key (program terminates 10s after last keypress)... 0xe0 0x22 0xe0 0xa2 What I want: I'd like a way to scan the incoming button presses, if the above method isn't correct. I'd like to either remap each button press to something that Ubuntu/Unity will ignore, or even better pass the keypress directly to Myth (I suspect this later is only possible with lirc, but I could be wrong). I would really like to do this with the in-kernel drivers, i.e. without explicitly loading lirc; if that's the way the world is going, I'd rather find a way to map the current behaviour to what I want, rather than forcing the 'old' arrangement of loading lirc outside the kernel. Learning something new is also worthwhile! My guess: I'm assuming that this will require using setkeycodes, but have had trouble finding enough information to configure this. Any help greatly appreciated!

  Read the article

• Radeon Mobility HD 5470 Not Working on Ubuntu 10.10

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Radeon Mobility HD 5470 Not Working

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• VirtualBox 3.2 is released! A Red Letter Day?

  - by Fat Bloke

  Big news today! A new release of VirtualBox packed full of innovation and improvements. Over the next few weeks we'll take a closer look at some of these new features in a lot more depth, but today we'll whet your appetite with the headline descriptions. To start with, we should point out that this is the first Oracle-branded version which makes today a real Red-letter day ;-)  Oracle VM VirtualBox 3.2 Version 3.2 moves VirtualBox forward in 3 main areas ( handily, all beginning with "P" ) : performance, power and supported guest operating system platforms.  Let's take a look: Performance New Latest Intel hardware support - Harnessing the latest in chip-level support for virtualization, VirtualBox 3.2 supports new Intel Core i5 and i7 processor and Intel Xeon processor 5600 Series support for Unrestricted Guest Execution bringing faster boot times for everything from Windows to Solaris guests; New Large Page support - Reducing the size and overhead of key system resources, Large Page support delivers increased performance by enabling faster lookups and shorter table creation times. New In-hypervisor Networking - Significant optimization of the networking subsystem has reduced context switching between guests and host, increasing network throughput by up to 25%. New New Storage I/O subsystem - VirtualBox 3.2 offers a completely re-worked virtual disk subsystem which utilizes asynchronous I/O to achieve high-performance whilst maintaining high data integrity; New Remote Video Acceleration - The unique built-in VirtualBox Remote Display Protocol (VRDP), which is primarily used in virtual desktop infrastructure deployments, has been enhanced to deliver video acceleration. This delivers a rich user experience coupled with reduced computational expense, which is vital when servers are running hundreds of virtual machines; Power New Page Fusion - Traditional Page Sharing techniques have suffered from long and expensive cache construction as pages are scrutinized as candidates for de-duplication. Taking a smarter approach, VirtualBox Page Fusion uses intelligence in the guest virtual machine to determine much more rapidly and accurately those pages which can be eliminated thereby increasing the capacity or vm density of the system; New Memory Ballooning- Ballooning provides another method to increase vm density by allowing the memory of one guest to be recouped and made available to others; New Multiple Virtual Monitors - VirtualBox 3.2 now supports multi-headed virtual machines with up to 8 virtual monitors attached to a guest. Each virtual monitor can be a host window, or be mapped to the hosts physical monitors; New Hot-plug CPU's - Modern operating systems such Windows Server 2008 x64 Data Center Edition or the latest Linux server platforms allow CPUs to be dynamically inserted into a system to provide incremental computing power while the system is running. Version 3.2 introduces support for Hot-plug vCPUs, allowing VirtualBox virtual machines to be given more power, with zero-downtime of the guest; New Virtual SAS Controller - VirtualBox 3.2 now offers a virtual SAS controller, enabling it to run the most demanding of high-end guests; New Online Snapshot Merging - Snapshots are powerful but can eat up disk space and need to be pruned from time to time. Historically, machines have needed to be turned off to delete or merge snapshots but with VirtualBox 3.2 this operation can be done whilst the machines are running. This allows sophisticated system management with minimal interruption of operations; New OVF Enhancements - VirtualBox has supported the OVF standard for virtual machine portability for some time. Now with 3.2, VirtualBox specific configuration data is also stored in the standard allowing richer virtual machine definitions without compromising portability; New Guest Automation - The Guest Automation APIs allow host-based logic to drive operations in the guest; Platforms New USB Keyboard and Mouse - Support more guests that require USB input devices; New Oracle Enterprise Linux 5.5 - Support for the latest version of Oracle's flagship Linux platform; New Ubuntu 10.04 ("Lucid Lynx") - Support for both the desktop and server version of the popular Ubuntu Linux distribution; And as a man once said, "just one more thing" ... New Mac OS X (experimental) - On Apple hardware only, support for creating virtual machines run Mac OS X. All in all this is a pretty powerful release packed full of innovation and speedups. So what are you waiting for?  -FB 

  Read the article

• Wireless cycling between connected and disconnected

  - by Tony Kilgore

  My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

  Read the article

• How to get faster graphics in KVM? VNC is painfully slow with Haiku OS guest, Spice won't install and SDL doesn't work

  - by Don Quixote

  I've been coming up to speed on the Haiku operating system, an Open Source clone of BeOS 5 Pro. I'm using an Apple MacBook Pro as my development machine. Apple's BootCamp BIOS does not support more than four partitions on the internal hard drive. While I can set up extended and logical partitions, doing so will prevent any of the installed operating systems from booting. To run Haiku directly on the iron, I boot it off a USB stick. Using external storage is also helpful because I am perpetually out of filesystem space. While VirtualBox is documented to allow access to physical drives, I could not actually get it to work. Also VirtualBox can only use one of the host CPU's cores. While VB guests can be configured for more than one CPU, they are only emulated. A full build of the Haiku OS takes 4.5 under VB. I had the hope of reducing build times by using KVM instead, but it's not working nearly as well as VirtualBox did. The Linux Kernel Virtual Machine is broken in all manner of fundamental ways as seen from Haiku. But I'm a coder; maybe I could contribute to fixing some of those problems. The first problem I've got is that Haiku's video in virt-manager is quite painfully slow. When I drag Haiku windows around the desktop, they lag quite far behind where my mouse is. It's quite difficult to move a window to a precise position on the screen. Just imagine that the mouse was connected to the window title bar with a really stretchy spring. Also Haiku's mouse lags quite far behind where I have moved it. I found lots of Personal Package Archives that enable Spice from QEMU / KVM at the Ubuntu Personal Package Arhives. I tried a few of the PPAs but none of them worked; with one of them, the command "add-apt-repository" crashed with a traceback. There is a Wiki page about Spice, but it says that it only works on 64-bit. My Early 2006 MacBook Pro is 32-bit. Its Apple Model Identifier is MacBookPro1,1; these use Core Duos NOT Core 2 Duos. I don't mind building a source deb for 32-bit if I can expect it to work. Is there some reason that Spice should be 64-bit only? Does it need features of the x86_64 Instruction Set Architecture that x86 does not have? When I try using SDL from virt-manager, the configuration for Local SDL Window says "Xauth: /home/mike/.Xauthority". When I try to start my guest, virt-manager emits an error. When I Googled the error message, the usual solution was to make ~/.Xauthority readible. However, .Xauthorty does not exist in my home directory. Instead I have a $XAUTHORITY environment variable. There is no way to configure SDL in virt-manager to use $XAUTHORITY instead of ~/.Xauthority. Neither does it work to copy the value of $XAUTHORITY into the file. I am ready to scream, because I've been five fscking days trying to make KVM work for Haiku development. There is a whole lot more that is broken than the slow video. All I really want to do for now is speed up my full builds of Haiku by using "jam -j2" to use both cores in my CPU. I may try Xen next, but the last time I monkeyed with Xen it was far, far more broken than I am finding KVM to be. Just for now, I would be satisfied if there were some way to use my USB stick as a drive in VirtualBox. VB does allow me to configure /dev/sdb as a drive, but it always causes a fatal error when I try to launch the guest. Thank You For Any Advice You Can Give Me. -

  Read the article

• How to fix: Ubuntu 12.04 reboots after loading with elilo

  - by Casey

  I have an HP p6-2120 with CPU: AMD A6-3620 APU with Radeon Graphics RAM: 6GB BIOS: HO2_710.ROM v7.10 [AMI v7.10 4/19/2012] Disk: SATA1 (/dev/sda) - 1 TB (windows) Disk: SATA2 (/dev/sdb) - 1 TB partitioned using "parted -a optimal /dev/sdb" as follows: .. 1049KB 201MB FAT32 boot flag set .. 201MB 60GB ext2 (/) .. 68GB 78GB linux-swap(v1) (swap) .. 78GB 790GB ext4 (/home) .. - rest is "free" space reserved for other purposes (eventually) ubuntu: 12.04.1 LTS [specifically: Release 12.04 (precise) 64-bit] kernel: linux 3.2.0-29-generic I created a bootable EFI USB from the ISO (64-bit) which I downloaded. I can run and install from the USB without any problems. The BIOS is an EFI bios that appears to be capable of booting in either EFI or Legacy mode. Initially, I did the "standard" install with NOTHING on disk2, and let the installer configure everything. The net result of this was that when I started the computer and forced it into "boot" menu mode, it DOES NOT recognize SATA2 as an EFI drive, and when I attempt to "legacy" boot from it, I get the message "ERROR: No Boot Disk has been detected." The "standard" install created one large partition that consumed the entire disk. At that point, I manually partitioned the disk (using sudo parted -a optimal /dev/sdb) as described above. I selected the "other" install, and changed the /dev/sdb1 to "bios_grub", /dev/sdb2 as "/" (ext4), /dev/sdb3 as swap, and /dev/sdb4 as "/home". [Note: fearing that possibly elilo did not recognize ext4, I switched /dev/sdb2 to ext2 and re-insalled] The net result was that the install appeared to trash the /dev/sdb1 partition so that it was NOT readable by anything. I re-formated /dev/sdb1 as FAT32 and set the boot flag. I repeated the install ignoring the messages about no bios_grub partition. After several attempts to get GRUB2 to work, I switched to elilo. I downloaded the most recent version and copied it (elilo-3.14-ia64.efi) to /dev/sdb1/efi/boot/bootx64.efi. (The BIOS boot loader did not recognize it either as elilo-3.14.ia64.efi or as elilo.efi. Based on the advice in one of the web-pages I found, I renamed it to bootx64.efi. This worked.) In that same directory (/efi/boot), I copied the file pointed to the link in /dev/sdb2/vmlinuz to /efi/boot/vmlinuz, and the file pointed to the link in /dev/sdb2/initrd.img to /efi/boot/initrd.img. I created an elilo.conf file as follows: timeout=5000 prompt default=linux-boot image=vmlinuz label=linux-boot read-only initrd=initrd.img root=/dev/sdb2 The /efi/boot directory contains 4 files: bootx64.efi elilo.conf vmlinuz initrd.img When I power-cycle the computer and force the boot menu, drive2 shows up as an EFI bootable drive. When I select it, I get the elilo prompt. Pressing , it appears to load the kernal (I have tried it with verbose=5, and there is a long string of messages with the final one a command line to load the kernel and a series of several dots that fly by) then the screen goes blank, and it reboots the computer. [Note: I have also tried substituting the UUID as found in the /etc/fstab of the installed system for the root directory. This had no effect.] This is a brief synopsis of several nights of fiddling with this. I would deeply appreciate any help you can give.

  Read the article

• Asus X202e VivoBook, dual boot. How to get around UEFI and have Win8 & Ubuntu?

  - by Nukeface

  I've gotten my hands on an Asus Vivobook X202e. I like it, handy to use, small, etc etc. Oh, it's the i3 core version. For school I still need Windows * sigh * for the .NET development. (I know, possible in Ubuntu, this n that, but for ease atm wanting to keep it with Win8). So. How to install both on this little thing? I've found a way into the BIOS (before splash screen, mash F2. Works only after reboot, not cold boot). But the whole boot loading setup is different than from what I know, and I must've messed up something because it's been "Attempting Repairs", "Analyzing hard disk", and a bunch of other things for the past 15 minutes. (All I've done is selected "disabled" on secure boot, picky as ** Microsoft). Keeping the original Windows installation is of no concern. Found the product key already and have a clean install waiting. BTW, not trying to leech knowledge, even though first question and no answers. I'm more and more active on Stackoverflow. But, especially due to secure boot and windows 8, I'm going over to Ubuntu. Well, more and more anyway, I like my Windows based games as well ;) UPDATE Managed to do a clean install of Windows 8 Pro. After disabling Secure Boot, also had to disable fast boot, and enable Launch CSM, leaving the option which appeared (Launch PXE OpROM) disabled. Then I rebooted, with the USB Boot drive I created using the Windows 7 USB DVD Download Tool (scroll down for download link), provided by Microsoft. During the installation, I chose to install a clean version, therefor deleted the partitions containing current windows files. I left the Recovery partition (you never know...). Of course, the new Windows Installation dit not like this. Apparantly Windows cannot be installed on a GPT hard disk. Remember I hadn't changed the partition table, was still factory default! Minus a few partitions, granted. So deleted ALL partittions, did a format of the disk, created a new partition. Et voila, Windows installation started. FINALLY! WONDROUS After the installation, Windows still had background images located in C:/Users/ ME /AppData/Local/Microsoft/Themes/RoamedThemeFiles/DesktopBackground/ that I had in the previous installation. Before doing: format, delete partition, cascade partitions, create new partition of different size, format partition, install Windows. It managed to keep the images through all that. Anyone got an idea on that one? It also remembered the settings for the Windows Aero theme... UPDATED QUESTION: After all this you'd think I'd have the rest figured out. Wrong. Ubuntu 12.10, 64 bit installation can't read the partitioning of the hdd during the installation. Any ideas on how to fix this so the install for a dual-boot system can proceed? (Preferably without starting anew with Windows as well ;) )

  Read the article

• Print raw data to a thermal-printer using .NET

  - by blauesocke

  I'm trying to print out raw ascii data to a thermal printer. I do this by using this code example: http://support.microsoft.com/kb/322091 but my printer prints always only one character and this not until I press the form feed button. If I print something with notepad the printer will do a form feed automatically but without printing any text. The printer is connected via usb over a lpt2usb adapter and Windows 7 uses the "Generic - Generic / Text Only" driver. Anyone knows what is going wrong? How is it possible to print some words and do some form feeds? Are there some control characters I have to send? And if yes: How do I send them? Edit 14.04.2010 21:51 My code (C#) looks like this: PrinterSettings s = new PrinterSettings(); s.PrinterName = "Generic / Text Only"; RawPrinterHelper.SendStringToPrinter(s.PrinterName, "Test"); This code will return a "T" after I pressed the form feed button (This litte black button here: swissmania.ch/images/935-151.jpg - sorry, not enough reputation for two hyperlinks) Edit 15.04.2010 16:56 I'm using now the code form here: c-sharpcorner.com/UploadFile/johnodonell/PrintingDirectlytothePrinter11222005001207AM/PrintingDirectlytothePrinter.aspx I modified it a bit that I can use the following code: byte[] toSend; // 10 = line feed // 13 carriage return/form feed toSend = new byte[1] { 13 }; PrintDirect.WritePrinter(lhPrinter, toSend, toSend.Length, ref pcWritten); Running this code has the same effekt like pressing the form feed button, it works fine! But code like this still does not work: byte[] toSend; // 10 = line feed // 13 carriage return/form feed toSend = new byte[2] { 66, 67 }; PrintDirect.WritePrinter(lhPrinter, toSend, toSend.Length, ref pcWritten); This will print out just a "B" but I expect "BC" and after running any code I have to reconnect the USB cable to make it work agian. Any ideas?

  Read the article

• rails + sheevaplug = rails home development server and more

  - by microspino

  Hello I'd like to build a "Rails Brick" using a Sheevaplug from Marvell (O.S. is Ubuntu out of the box but You can install other distributions on It). It will be a home server and a silent, low cost (99$) low energy development machine. I'd like to add rails RVM, lot of gems, git-based heroku like deployment, passenger + nginx. This way I could have a portable server with a complete development environment and maybe I could find a hosting company where I can co-locate a grid of this devices or I can sell It as a simple little server for 10 or less users offices, with some centralized rails services (I think to a CMS, a BLOG, a WIKI, calendar or whatever this little jewel could afford). The usb port could make It a print server too or a UMTS link to the web via HUAWEI like usb UMTS keys. Can you give me some hint about: Is this project a crazy-close-to-failure idea? Why? which gem would You include? which rails open source app would you suggest? I have already an Excito Bubba Server at home, I saw the TonidoPlug so It came up in my mind to build something similiar but Rails based (Bubba is PHP based, TonidoPlug I don't know but It does not seems a Rails thing).

  Read the article

• Linux: How to find all serial devices (ttyS, ttyUSB and others)?

  - by Thomas Tempelmann

  What is the proper way to get a list of all available serial ports/devices on a Linux system? In other words, when I iterate over all devices in /dev/, how do I tell which ones are serial ports in the classic way, i.e. those usually supporting baud rates and RTS/CTS flow control? The solution would be coded in C. I ask because I am using a 3rd party library that does this clearly wrong: It appears to only iterate over /dev/ttyS*. The problem is that there are, for instance, serial ports over USB (provided by USB-RS232 adapters), and those are listed under /dev/ttyUSB*. And reading the Serial-HOWTO at Linux.org, I get the idea that there'll be other name spaces as well, as time comes. So I need to find the official way to detect serial devices. Problem is that there appears none documented, or I can't find it. I imagine one way would be to open all files from /dev/tty* and call a specific ioctl() on them that is only available on serial devices. Would that be a good solution, though?

  Read the article

• Correct initialization sequence for Linux serial port

  - by whitequark

  I wrote an application that must use serial ports on Linux, especially ttyUSB ones. Reading and writing operations are performed with standard select()/read() loop and write(), and there is probably nothing wrong in them, but initialization code (or absence of some part of it) damages something in the tty subsystem. Here it is: vuxboot(string filename, unsigned baud = B115200) : _debug(false) { _fd = open(filename.c_str(), O_RDWR | O_NOCTTY); if(!_fd) throw new io_error("cannot open port"); // Serial initialization was written with FTDI USB-to-serial converters // in mind. Anyway, who wants to use non-8n1 protocol? tcgetattr(_fd, &_termios); termios tio = {0}; tio.c_iflag = IGNPAR; tio.c_oflag = 0; tio.c_cflag = baud | CLOCAL | CREAD | CS8; tio.c_lflag = 0; tcflush(_fd, TCIFLUSH); tcsetattr(_fd, TCSANOW, &tio); } Another tcsetattr(_fd, TCSANOW, &_termios) sits in the destructor, but it is irrelevant. With or without this termios initialization, strange things happen in system after the application exits. Sometimes plain cat (or hd) exits immediately printing nothing or same stuff each time, sometimes it is waiting and not displaying any of the data that is surely sent onto the port; and close() (read() too, but not every time) emits a strange WARNING to dmesg referring to usb-serial.c. I checked the hardware and firmware tens of times (even on different machines) and I am sure it is working as intended; moreover, I stripped the firmware to just print same message over and over. How can I use serial port without destroying anything? Thanks.

  Read the article

• Webcam video stream processing.

  - by vikramtheone

  Hi Guys, I'm working with an image processing project, my final goal is to detect features on a real time video and finally track those features. I will be working with an Embedded Processor Platform called Freescale's i.MX515, it is a 32-bit media processor running on Ubuntu 9.04. Right now I'm working on the algorithms to locate the features, so, I'm using still images. When I'm satisfied with the results I will have to start using a video stream and I don't want to make use of a video file as a source stream, because then I will have to worry about video decoders then. Instead I would like to plug in a USB Wecam to the embedded platform (It has USB ports on it), directly take the frames as they are captured and send it to my application. I will take care to buy a webcam which will be supported in Linux (Device driver). But my question is will I be able to capture the incoming video stream from the webcam and send it to my application? Will I be able to configure the webcam and DMA to write the incoming frames in a particular memory location whose pointer I can simply pass to my application? (Confused!!!) I hope I could convey my doubts, can anyone guide me with what steps that I have to take to achieve all of these easily? Do you foresee any impossibility here? Help!!! Regards Vikram

  Read the article

• Android SDK not recognizing debug-able device.

  - by kal.zekdor

  I'm new to Android development, and am attempting to run a test application on my actual device. I followed the instructions at http://developer.android.com/guide/developing/device.html (and related links), but the Android Debug Bridge (adb) doesn't recognize my connected device. Some quick background info, I'm running WinXP, developing with Eclipse, with a Motorola Droid running Android 2.1 as my physical device. An overview of the steps I've taken: Installed the Android SDK, downloading all necessary packages. Enabled USB Debugging on my device. Connected Device via USB, installing the driver from the SDK folder. I'll stop here (though I continued to setup my application to be debug-able in Eclipse), because I at this point I noticed a problem. Running "sdk\tools\adb devices" at this point (at least, by my understanding), should list my device as connected. However, running this yields only: List of devices attached My device recognizes that it's connected to a computer in debug mode, and my computer recognizes the device. However, I can't seem to get the sdk to recognize it. I'll leave out the steps I used to setup Eclipse for debugging on a device, as it doesn't seem relevant to the problem. I'll include them if requested. If anyone has any ideas, I'd greatly appreciate some assistance. Thanks in advance for your time.

  Read the article

• Should I base my Embedded Linux product on Qt?

  - by Udi

  My company is developing a medical product. One of the components is a pda-like platform that will run embedded linux. We were considering Qt as the UI framework but found out that Qt is a lot more than that (we are not familiar with Qt). In general, the device needs to do the following: 1. Receive measurements over USB HID from another device (USB HID is used for convenience). 2. Process the measurements. 3. Store them in a database. 4. Interact with the user using the device's touch screen lcd. 5. Communicate (wi-fi, tcp-ip) with a central management station that collects the data and configures the device. 6. Include a web server to allow accessing the device via a browser. We intend to program in C++. My questions are: 1. Is that a good choice for such a device? 2. Assuming we choose Qt, how do we build our product? - Do we use Qt just as a GUI framework and write the application code in a separate process (passing messages between Qt and the application process)? - Do we write the entire application inside Qt, using all of the services the tool has to offer? - Another approach?

  Read the article

• are mobile can be used as a devices to develop application

  - by Richa Media and services

  I say that we can work @ mobile using a technique and work with any IDE and use any OS without problem like work on visual studio and use Window 7 How it possible ? 1. We use Mobile like a CPU and Use a monitor to watch code. We use samsung's techniques to display on monitor. it's give signal to monitor wirelessly to display code on monitor 2 We use Wireless keyboard and Mouse (if user like USB then he also use USB keyboard and mouse) 3. We use a component inside of mobile to control all devices like internet , wi-fi bluethoth. by component user easily setup , control and use feature. 4 don't be confused. i am sure to say that we not use mobile to watch code on mobile screen and Mobile 's keyboard because it's too smaller to work so we use Monitor (LCD) to display code and a keyboard to work comfortably and freely. 5. what are you think if you see a developer who work using this way 6. it is not impossible. give me some feedback and suggestion about your thinking on this technologies.

  Read the article

• threading and getting COM port of attached phone

  - by I__

  i have the following code: using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Linq; using System.Text; using System.Windows.Forms; using System.Threading; namespace WindowsFormsApplication1 { public partial class Form1 : Form { public Form1() { InitializeComponent(); } public class ThreadWork { public static void DoWork() { } } private void Form1_Load(object sender, EventArgs e) { ThreadStart myThreadDelegate = new ThreadStart(ThreadWork.DoWork); Thread myThread = new Thread(myThreadDelegate); myThread.Start(); // Begin communications serialPort1.Open(); serialPort1.Write("AT+CMGF=1\r\n"); //Thread.Sleep(500); serialPort1.Write("AT+CNMI=2,2\r\n"); //Thread.Sleep(500); serialPort1.Write("AT+CSCA=\"+4790002100\"\r\n"); //Thread.Sleep(500); } private void serialPort1_DataReceived_1(object sender, System.IO.Ports.SerialDataReceivedEventArgs e) { string response = serialPort1.ReadLine(); this.BeginInvoke(new MethodInvoker(() => textBox1.AppendText(response + "\r\n"))); } } } what i am trying to do is send AT COMMANDS to my phone which is attached to the computer through USB how do i know how to configure the properties of the serial port? (like which COM is the phone on [it's attached through USB], what about baudrate and databits?) when i run the program nothing really happens, i would like to send AT COMMANDS to my phone and the textbox is there to receive the response from my phone this is my first time using threads. am i using them correctly? what is the purpose of it in the current example? is it to just have a delay between send a response? what am i doing wrong?

  Read the article

• c# threading and getting COM port of attached phone

  - by I__

  i have the following code: using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Linq; using System.Text; using System.Windows.Forms; using System.Threading; namespace WindowsFormsApplication1 { public partial class Form1 : Form { public Form1() { InitializeComponent(); } public class ThreadWork { public static void DoWork() { } } private void Form1_Load(object sender, EventArgs e) { ThreadStart myThreadDelegate = new ThreadStart(ThreadWork.DoWork); Thread myThread = new Thread(myThreadDelegate); myThread.Start(); // Begin communications serialPort1.Open(); serialPort1.Write("AT+CMGF=1\r\n"); //Thread.Sleep(500); serialPort1.Write("AT+CNMI=2,2\r\n"); //Thread.Sleep(500); serialPort1.Write("AT+CSCA=\"+4790002100\"\r\n"); //Thread.Sleep(500); } private void serialPort1_DataReceived_1(object sender, System.IO.Ports.SerialDataReceivedEventArgs e) { string response = serialPort1.ReadLine(); this.BeginInvoke(new MethodInvoker(() => textBox1.AppendText(response + "\r\n"))); } } } what i am trying to do is send AT COMMANDS to my phone which is attached to the computer through USB how do i know how to configure the properties of the serial port? (like which COM is the phone on [it's attached through USB], what about baudrate and databits?) when i run the program nothing really happens, i would like to send AT COMMANDS to my phone and the textbox is there to receive the response from my phone this is my first time using threads. am i using them correctly? what is the purpose of it in the current example? is it to just have a delay between send a response? what am i doing wrong?

  Read the article

• Portable Eclipse

  - by Jeach

  I'm trying to port my entire 'workspace' to a USB key (including the Eclipse executable) so that I can carry my work anywhere with me and work off the key directly. My directory hierarchy is similar to this: /workspace/eclipse - Where my current eclipse binary is stored /workspace/codebase - Where I keep the root of all my eclipse projects /workspace/resources - Where I keep all project files (images, docs, libs, etc.) It all works perfectly fine on one system. But when I change over to another system, the USB key gets mounted on another drive. For example, on my laptop, I get 'E:\', on my PC, I get 'K:\' and at work I get 'F:\', etc, etc. This means that because Eclipse (for 'some' reason) seems to only use full path names (including driver letters) in every single one of its configuration files (such as .classpath), nothing ever works when I want to work on another system. I put a 'libs' directory in the base of every project and populate it with its dependent JAR files. Why doesn't it use relative names instead, so that I could specify something like "../../libs/log4j.jar"? Anyone know how to fix this problem? Does anyone know of a workaround for this? For some reason, I really doubt I'm the first developer to do this! Thanks for your help and any suggestions.

  Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >